| 1 | @c Copyright (C) 2002-2014 Free Software Foundation, Inc. |
| 2 | @c This is part of the GAS manual. |
| 3 | @c For copying conditions, see the file as.texinfo. |
| 4 | @ifset GENERIC |
| 5 | @page |
| 6 | @node MSP430-Dependent |
| 7 | @chapter MSP 430 Dependent Features |
| 8 | @end ifset |
| 9 | @ifclear GENERIC |
| 10 | @node Machine Dependencies |
| 11 | @chapter MSP 430 Dependent Features |
| 12 | @end ifclear |
| 13 | |
| 14 | @cindex MSP 430 support |
| 15 | @cindex 430 support |
| 16 | @menu |
| 17 | * MSP430 Options:: Options |
| 18 | * MSP430 Syntax:: Syntax |
| 19 | * MSP430 Floating Point:: Floating Point |
| 20 | * MSP430 Directives:: MSP 430 Machine Directives |
| 21 | * MSP430 Opcodes:: Opcodes |
| 22 | * MSP430 Profiling Capability:: Profiling Capability |
| 23 | @end menu |
| 24 | |
| 25 | @node MSP430 Options |
| 26 | @section Options |
| 27 | @cindex MSP 430 options (none) |
| 28 | @cindex options for MSP430 (none) |
| 29 | @table @code |
| 30 | |
| 31 | @item -mmcu |
| 32 | selects the mcu architecture. If the architecture is 430Xv2 then this |
| 33 | also enables NOP generation unless the @option{-mN} is also specified. |
| 34 | |
| 35 | @item -mcpu |
| 36 | selects the cpu architecture. If the architecture is 430Xv2 then this |
| 37 | also enables NOP generation unless the @option{-mN} is also specified. |
| 38 | |
| 39 | @item -mP |
| 40 | enables polymorph instructions handler. |
| 41 | |
| 42 | @item -mQ |
| 43 | enables relaxation at assembly time. DANGEROUS! |
| 44 | |
| 45 | @item -ml |
| 46 | indicates that the input uses the large code model. |
| 47 | |
| 48 | @item -mn |
| 49 | enables the generation of a NOP instruction following any instruction |
| 50 | that might change the interrupts enabled/disabled state. The |
| 51 | pipelined nature of the MSP430 core means that any instruction that |
| 52 | changes the interrupt state (@code{EINT}, @code{DINT}, @code{BIC #8, |
| 53 | SR}, @code{BIS #8, SR} or @code{MOV.W <>, SR}) must be |
| 54 | followed by a NOP instruction in order to ensure the correct |
| 55 | processing of interrupts. By default it is up to the programmer to |
| 56 | supply these NOP instructions, but this command line option enables |
| 57 | the automatic insertion by the assembler, if they are missing. |
| 58 | |
| 59 | @item -mN |
| 60 | disables the generation of a NOP instruction following any instruction |
| 61 | that might change the interrupts enabled/disabled state. This is the |
| 62 | default behaviour. |
| 63 | |
| 64 | @item -mz |
| 65 | tells the assembler to generate a warning message if a NOP does not |
| 66 | immediately forllow an instruction that enables or disables |
| 67 | interrupts. This is the default. |
| 68 | |
| 69 | Note that this option can be stacked with the @option{-mn} option so |
| 70 | that the assembler will both warn about missing NOP instructions and |
| 71 | then insert them automatically. |
| 72 | |
| 73 | @item -mZ |
| 74 | disables warnings about missing NOP instructions. |
| 75 | |
| 76 | @item -md |
| 77 | mark the object file as one that requires data to copied from ROM to |
| 78 | RAM at execution startup. Disabled by default. |
| 79 | |
| 80 | @end table |
| 81 | |
| 82 | @node MSP430 Syntax |
| 83 | @section Syntax |
| 84 | @menu |
| 85 | * MSP430-Macros:: Macros |
| 86 | * MSP430-Chars:: Special Characters |
| 87 | * MSP430-Regs:: Register Names |
| 88 | * MSP430-Ext:: Assembler Extensions |
| 89 | @end menu |
| 90 | |
| 91 | @node MSP430-Macros |
| 92 | @subsection Macros |
| 93 | |
| 94 | @cindex Macros, MSP 430 |
| 95 | @cindex MSP 430 macros |
| 96 | The macro syntax used on the MSP 430 is like that described in the MSP |
| 97 | 430 Family Assembler Specification. Normal @code{@value{AS}} |
| 98 | macros should still work. |
| 99 | |
| 100 | Additional built-in macros are: |
| 101 | |
| 102 | @table @code |
| 103 | |
| 104 | @item llo(exp) |
| 105 | Extracts least significant word from 32-bit expression 'exp'. |
| 106 | |
| 107 | @item lhi(exp) |
| 108 | Extracts most significant word from 32-bit expression 'exp'. |
| 109 | |
| 110 | @item hlo(exp) |
| 111 | Extracts 3rd word from 64-bit expression 'exp'. |
| 112 | |
| 113 | @item hhi(exp) |
| 114 | Extracts 4rd word from 64-bit expression 'exp'. |
| 115 | |
| 116 | @end table |
| 117 | |
| 118 | They normally being used as an immediate source operand. |
| 119 | @smallexample |
| 120 | mov #llo(1), r10 ; == mov #1, r10 |
| 121 | mov #lhi(1), r10 ; == mov #0, r10 |
| 122 | @end smallexample |
| 123 | |
| 124 | @node MSP430-Chars |
| 125 | @subsection Special Characters |
| 126 | |
| 127 | @cindex line comment character, MSP 430 |
| 128 | @cindex MSP 430 line comment character |
| 129 | A semicolon (@samp{;}) appearing anywhere on a line starts a comment |
| 130 | that extends to the end of that line. |
| 131 | |
| 132 | If a @samp{#} appears as the first character of a line then the whole |
| 133 | line is treated as a comment, but it can also be a logical line number |
| 134 | directive (@pxref{Comments}) or a preprocessor control command |
| 135 | (@pxref{Preprocessing}). |
| 136 | |
| 137 | @cindex line separator, MSP 430 |
| 138 | @cindex statement separator, MSP 430 |
| 139 | @cindex MSP 430 line separator |
| 140 | Multiple statements can appear on the same line provided that they are |
| 141 | separated by the @samp{@{} character. |
| 142 | |
| 143 | @cindex identifiers, MSP 430 |
| 144 | @cindex MSP 430 identifiers |
| 145 | The character @samp{$} in jump instructions indicates current location and |
| 146 | implemented only for TI syntax compatibility. |
| 147 | |
| 148 | @node MSP430-Regs |
| 149 | @subsection Register Names |
| 150 | |
| 151 | @cindex MSP 430 register names |
| 152 | @cindex register names, MSP 430 |
| 153 | General-purpose registers are represented by predefined symbols of the |
| 154 | form @samp{r@var{N}} (for global registers), where @var{N} represents |
| 155 | a number between @code{0} and @code{15}. The leading |
| 156 | letters may be in either upper or lower case; for example, @samp{r13} |
| 157 | and @samp{R7} are both valid register names. |
| 158 | |
| 159 | @cindex special purpose registers, MSP 430 |
| 160 | Register names @samp{PC}, @samp{SP} and @samp{SR} cannot be used as register names |
| 161 | and will be treated as variables. Use @samp{r0}, @samp{r1}, and @samp{r2} instead. |
| 162 | |
| 163 | |
| 164 | @node MSP430-Ext |
| 165 | @subsection Assembler Extensions |
| 166 | @cindex MSP430 Assembler Extensions |
| 167 | |
| 168 | @table @code |
| 169 | |
| 170 | @item @@rN |
| 171 | As destination operand being treated as @samp{0(rn)} |
| 172 | |
| 173 | @item 0(rN) |
| 174 | As source operand being treated as @samp{@@rn} |
| 175 | |
| 176 | @item jCOND +N |
| 177 | Skips next N bytes followed by jump instruction and equivalent to |
| 178 | @samp{jCOND $+N+2} |
| 179 | |
| 180 | @end table |
| 181 | |
| 182 | Also, there are some instructions, which cannot be found in other assemblers. |
| 183 | These are branch instructions, which has different opcodes upon jump distance. |
| 184 | They all got PC relative addressing mode. |
| 185 | |
| 186 | @table @code |
| 187 | @item beq label |
| 188 | A polymorph instruction which is @samp{jeq label} in case if jump distance |
| 189 | within allowed range for cpu's jump instruction. If not, this unrolls into |
| 190 | a sequence of |
| 191 | @smallexample |
| 192 | jne $+6 |
| 193 | br label |
| 194 | @end smallexample |
| 195 | |
| 196 | @item bne label |
| 197 | A polymorph instruction which is @samp{jne label} or @samp{jeq +4; br label} |
| 198 | |
| 199 | @item blt label |
| 200 | A polymorph instruction which is @samp{jl label} or @samp{jge +4; br label} |
| 201 | |
| 202 | @item bltn label |
| 203 | A polymorph instruction which is @samp{jn label} or @samp{jn +2; jmp +4; br label} |
| 204 | |
| 205 | @item bltu label |
| 206 | A polymorph instruction which is @samp{jlo label} or @samp{jhs +2; br label} |
| 207 | |
| 208 | @item bge label |
| 209 | A polymorph instruction which is @samp{jge label} or @samp{jl +4; br label} |
| 210 | |
| 211 | @item bgeu label |
| 212 | A polymorph instruction which is @samp{jhs label} or @samp{jlo +4; br label} |
| 213 | |
| 214 | @item bgt label |
| 215 | A polymorph instruction which is @samp{jeq +2; jge label} or @samp{jeq +6; jl +4; br label} |
| 216 | |
| 217 | @item bgtu label |
| 218 | A polymorph instruction which is @samp{jeq +2; jhs label} or @samp{jeq +6; jlo +4; br label} |
| 219 | |
| 220 | @item bleu label |
| 221 | A polymorph instruction which is @samp{jeq label; jlo label} or @samp{jeq +2; jhs +4; br label} |
| 222 | |
| 223 | @item ble label |
| 224 | A polymorph instruction which is @samp{jeq label; jl label} or @samp{jeq +2; jge +4; br label} |
| 225 | |
| 226 | @item jump label |
| 227 | A polymorph instruction which is @samp{jmp label} or @samp{br label} |
| 228 | @end table |
| 229 | |
| 230 | |
| 231 | @node MSP430 Floating Point |
| 232 | @section Floating Point |
| 233 | |
| 234 | @cindex floating point, MSP 430 (@sc{ieee}) |
| 235 | @cindex MSP 430 floating point (@sc{ieee}) |
| 236 | The MSP 430 family uses @sc{ieee} 32-bit floating-point numbers. |
| 237 | |
| 238 | @node MSP430 Directives |
| 239 | @section MSP 430 Machine Directives |
| 240 | |
| 241 | @cindex machine directives, MSP 430 |
| 242 | @cindex MSP 430 machine directives |
| 243 | @table @code |
| 244 | @cindex @code{file} directive, MSP 430 |
| 245 | @item .file |
| 246 | This directive is ignored; it is accepted for compatibility with other |
| 247 | MSP 430 assemblers. |
| 248 | |
| 249 | @quotation |
| 250 | @emph{Warning:} in other versions of the @sc{gnu} assembler, @code{.file} is |
| 251 | used for the directive called @code{.app-file} in the MSP 430 support. |
| 252 | @end quotation |
| 253 | |
| 254 | @cindex @code{line} directive, MSP 430 |
| 255 | @item .line |
| 256 | This directive is ignored; it is accepted for compatibility with other |
| 257 | MSP 430 assemblers. |
| 258 | |
| 259 | @cindex @code{arch} directive, MSP 430 |
| 260 | @item .arch |
| 261 | Sets the target microcontroller in the same way as the @option{-mmcu} |
| 262 | command line option. |
| 263 | |
| 264 | @cindex @code{cpu} directive, MSP 430 |
| 265 | @item .cpu |
| 266 | Sets the target architecture in the same way as the @option{-mcpu} |
| 267 | command line option. |
| 268 | |
| 269 | @cindex @code{profiler} directive, MSP 430 |
| 270 | @item .profiler |
| 271 | This directive instructs assembler to add new profile entry to the object file. |
| 272 | |
| 273 | @cindex @code{refsym} directive, MSP 430 |
| 274 | @item .refsym |
| 275 | This directive instructs assembler to add an undefined reference to |
| 276 | the symbol following the directive. The maximum symbol name length is |
| 277 | 1023 characters. No relocation is created for this symbol; it will |
| 278 | exist purely for pulling in object files from archives. Note that |
| 279 | this reloc is not sufficient to prevent garbage collection; use a |
| 280 | KEEP() directive in the linker file to preserve such objects. |
| 281 | |
| 282 | @end table |
| 283 | |
| 284 | @node MSP430 Opcodes |
| 285 | @section Opcodes |
| 286 | |
| 287 | @cindex MSP 430 opcodes |
| 288 | @cindex opcodes for MSP 430 |
| 289 | @code{@value{AS}} implements all the standard MSP 430 opcodes. No |
| 290 | additional pseudo-instructions are needed on this family. |
| 291 | |
| 292 | For information on the 430 machine instruction set, see @cite{MSP430 |
| 293 | User's Manual, document slau049d}, Texas Instrument, Inc. |
| 294 | |
| 295 | @node MSP430 Profiling Capability |
| 296 | @section Profiling Capability |
| 297 | |
| 298 | @cindex MSP 430 profiling capability |
| 299 | @cindex profiling capability for MSP 430 |
| 300 | It is a performance hit to use gcc's profiling approach for this tiny target. |
| 301 | Even more -- jtag hardware facility does not perform any profiling functions. |
| 302 | However we've got gdb's built-in simulator where we can do anything. |
| 303 | |
| 304 | We define new section @samp{.profiler} which holds all profiling information. |
| 305 | We define new pseudo operation @samp{.profiler} which will instruct assembler to |
| 306 | add new profile entry to the object file. Profile should take place at the |
| 307 | present address. |
| 308 | |
| 309 | Pseudo operation format: |
| 310 | |
| 311 | @samp{.profiler flags,function_to_profile [, cycle_corrector, extra]} |
| 312 | |
| 313 | |
| 314 | where: |
| 315 | |
| 316 | @table @code |
| 317 | |
| 318 | @table @code |
| 319 | |
| 320 | @samp{flags} is a combination of the following characters: |
| 321 | |
| 322 | @item s |
| 323 | function entry |
| 324 | @item x |
| 325 | function exit |
| 326 | @item i |
| 327 | function is in init section |
| 328 | @item f |
| 329 | function is in fini section |
| 330 | @item l |
| 331 | library call |
| 332 | @item c |
| 333 | libc standard call |
| 334 | @item d |
| 335 | stack value demand |
| 336 | @item I |
| 337 | interrupt service routine |
| 338 | @item P |
| 339 | prologue start |
| 340 | @item p |
| 341 | prologue end |
| 342 | @item E |
| 343 | epilogue start |
| 344 | @item e |
| 345 | epilogue end |
| 346 | @item j |
| 347 | long jump / sjlj unwind |
| 348 | @item a |
| 349 | an arbitrary code fragment |
| 350 | @item t |
| 351 | extra parameter saved (a constant value like frame size) |
| 352 | @end table |
| 353 | |
| 354 | @item function_to_profile |
| 355 | a function address |
| 356 | @item cycle_corrector |
| 357 | a value which should be added to the cycle counter, zero if omitted. |
| 358 | @item extra |
| 359 | any extra parameter, zero if omitted. |
| 360 | |
| 361 | @end table |
| 362 | |
| 363 | For example: |
| 364 | @smallexample |
| 365 | .global fxx |
| 366 | .type fxx,@@function |
| 367 | fxx: |
| 368 | .LFrameOffset_fxx=0x08 |
| 369 | .profiler "scdP", fxx ; function entry. |
| 370 | ; we also demand stack value to be saved |
| 371 | push r11 |
| 372 | push r10 |
| 373 | push r9 |
| 374 | push r8 |
| 375 | .profiler "cdpt",fxx,0, .LFrameOffset_fxx ; check stack value at this point |
| 376 | ; (this is a prologue end) |
| 377 | ; note, that spare var filled with |
| 378 | ; the farme size |
| 379 | mov r15,r8 |
| 380 | ... |
| 381 | .profiler cdE,fxx ; check stack |
| 382 | pop r8 |
| 383 | pop r9 |
| 384 | pop r10 |
| 385 | pop r11 |
| 386 | .profiler xcde,fxx,3 ; exit adds 3 to the cycle counter |
| 387 | ret ; cause 'ret' insn takes 3 cycles |
| 388 | @end smallexample |