Documentation/devicetree/bindings/mfd/qcom-rpm.txt

   1 Qualcomm Resource Power Manager (RPM)
   2
   3 This driver is used to interface with the Resource Power Manager (RPM) found in
   4 various Qualcomm platforms. The RPM allows each component in the system to vote
   5 for state of the system resources, such as clocks, regulators and bus
   6 frequencies.
   7
   8 - compatible:
   9         Usage: required
  10         Value type: <string>
  11         Definition: must be one of:
  12                     "qcom,rpm-apq8064"
  13                     "qcom,rpm-msm8660"
  14                     "qcom,rpm-msm8960"
  15                     "qcom,rpm-ipq8064"
  16                     "qcom,rpm-mdm9615"
  17
  18 - reg:
  19         Usage: required
  20         Value type: <prop-encoded-array>
  21         Definition: base address and size of the RPM's message ram
  22
  23 - interrupts:
  24         Usage: required
  25         Value type: <prop-encoded-array>
  26         Definition: three entries specifying the RPM's:
  27                     1. acknowledgement interrupt
  28                     2. error interrupt
  29                     3. wakeup interrupt
  30
  31 - interrupt-names:
  32         Usage: required
  33         Value type: <string-array>
  34         Definition: must be the three strings "ack", "err" and "wakeup", in order
  35
  36 - qcom,ipc:
  37         Usage: required
  38         Value type: <prop-encoded-array>
  39
  40         Definition: three entries specifying the outgoing ipc bit used for
  41                     signaling the RPM:
  42                     - phandle to a syscon node representing the apcs registers
  43                     - u32 representing offset to the register within the syscon
  44                     - u32 representing the ipc bit within the register
  45
  46
  47 = SUBNODES
  48
  49 The RPM exposes resources to its subnodes. The below bindings specify the set
  50 of valid subnodes that can operate on these resources.
  51
  52 == Regulators
  53
  54 Regulator nodes are identified by their compatible:
  55
  56 - compatible:
  57         Usage: required
  58         Value type: <string>
  59         Definition: must be one of:
  60                     "qcom,rpm-pm8058-regulators"
  61                     "qcom,rpm-pm8901-regulators"
  62                     "qcom,rpm-pm8921-regulators"
  63                     "qcom,rpm-pm8018-regulators"
  64
  65 - vdd_l0_l1_lvs-supply:
  66 - vdd_l2_l11_l12-supply:
  67 - vdd_l3_l4_l5-supply:
  68 - vdd_l6_l7-supply:
  69 - vdd_l8-supply:
  70 - vdd_l9-supply:
  71 - vdd_l10-supply:
  72 - vdd_l13_l16-supply:
  73 - vdd_l14_l15-supply:
  74 - vdd_l17_l18-supply:
  75 - vdd_l19_l20-supply:
  76 - vdd_l21-supply:
  77 - vdd_l22-supply:
  78 - vdd_l23_l24_l25-supply:
  79 - vdd_ncp-supply:
  80 - vdd_s0-supply:
  81 - vdd_s1-supply:
  82 - vdd_s2-supply:
  83 - vdd_s3-supply:
  84 - vdd_s4-supply:
  85         Usage: optional (pm8058 only)
  86         Value type: <phandle>
  87         Definition: reference to regulator supplying the input pin, as
  88                     described in the data sheet
  89
  90 - lvs0_in-supply:
  91 - lvs1_in-supply:
  92 - lvs2_in-supply:
  93 - lvs3_in-supply:
  94 - mvs_in-supply:
  95 - vdd_l0-supply:
  96 - vdd_l1-supply:
  97 - vdd_l2-supply:
  98 - vdd_l3-supply:
  99 - vdd_l4-supply:
 100 - vdd_l5-supply:
 101 - vdd_l6-supply:
 102 - vdd_s0-supply:
 103 - vdd_s1-supply:
 104 - vdd_s2-supply:
 105 - vdd_s3-supply:
 106 - vdd_s4-supply:
 107         Usage: optional (pm8901 only)
 108         Value type: <phandle>
 109         Definition: reference to regulator supplying the input pin, as
 110                     described in the data sheet
 111
 112 - vdd_l1_l2_l12_l18-supply:
 113 - vdd_l3_l15_l17-supply:
 114 - vdd_l4_l14-supply:
 115 - vdd_l5_l8_l16-supply:
 116 - vdd_l6_l7-supply:
 117 - vdd_l9_l11-supply:
 118 - vdd_l10_l22-supply:
 119 - vdd_l21_l23_l29-supply:
 120 - vdd_l24-supply:
 121 - vdd_l25-supply:
 122 - vdd_l26-supply:
 123 - vdd_l27-supply:
 124 - vdd_l28-supply:
 125 - vdd_ncp-supply:
 126 - vdd_s1-supply:
 127 - vdd_s2-supply:
 128 - vdd_s4-supply:
 129 - vdd_s5-supply:
 130 - vdd_s6-supply:
 131 - vdd_s7-supply:
 132 - vdd_s8-supply:
 133 - vin_5vs-supply:
 134 - vin_lvs1_3_6-supply:
 135 - vin_lvs2-supply:
 136 - vin_lvs4_5_7-supply:
 137         Usage: optional (pm8921 only)
 138         Value type: <phandle>
 139         Definition: reference to regulator supplying the input pin, as
 140                     described in the data sheet
 141
 142 - vin_lvs1-supply:
 143 - vdd_l7-supply:
 144 - vdd_l8-supply:
 145 - vdd_l9_l10_l11_l12-supply:
 146         Usage: optional (pm8018 only)
 147         Value type: <phandle>
 148         Definition: reference to regulator supplying the input pin, as
 149                     described in the data sheet
 150
 151 The regulator node houses sub-nodes for each regulator within the device. Each
 152 sub-node is identified using the node's name, with valid values listed for each
 153 of the pmics below.
 154
 155 pm8058:
 156         l0, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14, l15,
 157         l16, l17, l18, l19, l20, l21, l22, l23, l24, l25, s0, s1, s2, s3, s4,
 158         lvs0, lvs1, ncp
 159
 160 pm8901:
 161         l0, l1, l2, l3, l4, l5, l6, s0, s1, s2, s3, s4, lvs0, lvs1, lvs2, lvs3,
 162         mvs
 163
 164 pm8921:
 165         s1, s2, s3, s4, s7, s8, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11,
 166         l12, l14, l15, l16, l17, l18, l21, l22, l23, l24, l25, l26, l27, l28,
 167         l29, lvs1, lvs2, lvs3, lvs4, lvs5, lvs6, lvs7, usb-switch, hdmi-switch,
 168         ncp
 169
 170 pm8018:
 171         s1, s2, s3, s4, s5, , l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11,
 172         l12, l14, lvs1
 173
 174 The content of each sub-node is defined by the standard binding for regulators -
 175 see regulator.txt - with additional custom properties described below:
 176
 177 === Switch-mode Power Supply regulator custom properties
 178
 179 - bias-pull-down:
 180         Usage: optional
 181         Value type: <empty>
 182         Definition: enable pull down of the regulator when inactive
 183
 184 - qcom,switch-mode-frequency:
 185         Usage: required
 186         Value type: <u32>
 187         Definition: Frequency (Hz) of the switch-mode power supply;
 188                     must be one of:
 189                     19200000, 9600000, 6400000, 4800000, 3840000, 3200000,
 190                     2740000, 2400000, 2130000, 1920000, 1750000, 1600000,
 191                     1480000, 1370000, 1280000, 1200000
 192
 193 - qcom,force-mode:
 194         Usage: optional (default if no other qcom,force-mode is specified)
 195         Value type: <u32>
 196         Definition: indicates that the regulator should be forced to a
 197                    particular mode, valid values are:
 198                    QCOM_RPM_FORCE_MODE_NONE - do not force any mode
 199                    QCOM_RPM_FORCE_MODE_LPM - force into low power mode
 200                    QCOM_RPM_FORCE_MODE_HPM - force into high power mode
 201                    QCOM_RPM_FORCE_MODE_AUTO - allow regulator to automatically
 202                                               select its own mode based on
 203                                               realtime current draw, only for:
 204                                               pm8921 smps and ftsmps
 205
 206 - qcom,power-mode-hysteretic:
 207         Usage: optional
 208         Value type: <empty>
 209         Definition: select that the power supply should operate in hysteretic
 210                     mode, instead of the default pwm mode
 211
 212 === Low-dropout regulator custom properties
 213
 214 - bias-pull-down:
 215         Usage: optional
 216         Value type: <empty>
 217         Definition: enable pull down of the regulator when inactive
 218
 219 - qcom,force-mode:
 220         Usage: optional
 221         Value type: <u32>
 222         Definition: indicates that the regulator should not be forced to any
 223                    particular mode, valid values are:
 224                    QCOM_RPM_FORCE_MODE_NONE - do not force any mode
 225                    QCOM_RPM_FORCE_MODE_LPM - force into low power mode
 226                    QCOM_RPM_FORCE_MODE_HPM - force into high power mode
 227                    QCOM_RPM_FORCE_MODE_BYPASS - set regulator to use bypass
 228                                                 mode, i.e.  to act as a switch
 229                                                 and not regulate, only for:
 230                                                 pm8921 pldo, nldo and nldo1200
 231
 232 === Negative Charge Pump custom properties
 233
 234 - qcom,switch-mode-frequency:
 235         Usage: required
 236         Value type: <u32>
 237         Definition: Frequency (Hz) of the swith mode power supply;
 238                     must be one of:
 239                     19200000, 9600000, 6400000, 4800000, 3840000, 3200000,
 240                     2740000, 2400000, 2130000, 1920000, 1750000, 1600000,
 241                     1480000, 1370000, 1280000, 1200000
 242
 243 = EXAMPLE
 244
 245         #include <dt-bindings/mfd/qcom-rpm.h>
 246
 247         rpm@108000 {
 248                 compatible = "qcom,rpm-msm8960";
 249                 reg = <0x108000 0x1000>;
 250                 qcom,ipc = <&apcs 0x8 2>;
 251
 252                 interrupts = <0 19 0>, <0 21 0>, <0 22 0>;
 253                 interrupt-names = "ack", "err", "wakeup";
 254
 255                 regulators {
 256                         compatible = "qcom,rpm-pm8921-regulators";
 257                         vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
 258
 259                         s1 {
 260                                 regulator-min-microvolt = <1225000>;
 261                                 regulator-max-microvolt = <1225000>;
 262
 263                                 bias-pull-down;
 264
 265                                 qcom,switch-mode-frequency = <3200000>;
 266                         };
 267
 268                         pm8921_s4: s4 {
 269                                 regulator-min-microvolt = <1800000>;
 270                                 regulator-max-microvolt = <1800000>;
 271
 272                                 qcom,switch-mode-frequency = <1600000>;
 273                                 bias-pull-down;
 274
 275                                 qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
 276                         };
 277                 };
 278         };
 279