arch/arm/mach-imx/Kconfig

   1 menuconfig ARCH_MXC
   2         bool "Freescale i.MX family"
   3         depends on ARCH_MULTI_V4_V5 || ARCH_MULTI_V6_V7 || ARM_SINGLE_ARMV7M
   4         select ARCH_SUPPORTS_BIG_ENDIAN
   5         select CLKSRC_IMX_GPT
   6         select GENERIC_IRQ_CHIP
   7         select GPIOLIB
   8         select PINCTRL
   9         select PM_OPP if PM
  10         select SOC_BUS
  11         select SRAM
  12         help
  13           Support for Freescale MXC/iMX-based family of processors
  14
  15 if ARCH_MXC
  16
  17 config MXC_TZIC
  18         bool
  19
  20 config MXC_AVIC
  21         bool
  22
  23 config MXC_DEBUG_BOARD
  24         bool "Enable MXC debug board(for 3-stack)"
  25         depends on MACH_MX27_3DS || MACH_MX31_3DS || MACH_MX35_3DS
  26         help
  27           The debug board is an integral part of the MXC 3-stack(PDK)
  28           platforms, it can be attached or removed from the peripheral
  29           board. On debug board, several debug devices(ethernet, UART,
  30           buttons, LEDs and JTAG) are implemented. Between the MCU and
  31           these devices, a CPLD is added as a bridge which performs
  32           data/address de-multiplexing and decode, signal level shift,
  33           interrupt control and various board functions.
  34
  35 config HAVE_EPIT
  36         bool
  37
  38 config MXC_USE_EPIT
  39         bool "Use EPIT instead of GPT"
  40         depends on HAVE_EPIT
  41         help
  42           Use EPIT as the system timer on systems that have it. Normally you
  43           don't have a reason to do so as the EPIT has the same features and
  44           uses the same clocks as the GPT. Anyway, on some systems the GPT
  45           may be in use for other purposes.
  46
  47 config HAVE_IMX_ANATOP
  48         bool
  49
  50 config HAVE_IMX_GPC
  51         bool
  52         select PM_GENERIC_DOMAINS if PM
  53
  54 config HAVE_IMX_MMDC
  55         bool
  56
  57 config HAVE_IMX_SRC
  58         def_bool y if SMP
  59         select ARCH_HAS_RESET_CONTROLLER
  60
  61 config IMX_HAVE_IOMUX_V1
  62         bool
  63
  64 config ARCH_MXC_IOMUX_V3
  65         bool
  66
  67 config SOC_IMX1
  68         bool
  69         select CPU_ARM920T
  70         select IMX_HAVE_IOMUX_V1
  71         select MXC_AVIC
  72         select PINCTRL_IMX1
  73
  74 config SOC_IMX21
  75         bool
  76         select CPU_ARM926T
  77         select IMX_HAVE_IOMUX_V1
  78         select MXC_AVIC
  79
  80 config SOC_IMX27
  81         bool
  82         select CPU_ARM926T
  83         select IMX_HAVE_IOMUX_V1
  84         select MXC_AVIC
  85         select PINCTRL_IMX27
  86
  87 config SOC_IMX31
  88         bool
  89         select CPU_V6
  90         select MXC_AVIC
  91         select SMP_ON_UP if SMP
  92
  93 config SOC_IMX35
  94         bool
  95         select ARCH_MXC_IOMUX_V3
  96         select HAVE_EPIT
  97         select MXC_AVIC
  98         select PINCTRL_IMX35
  99         select SMP_ON_UP if SMP
 100
 101 if ARCH_MULTI_V4T
 102
 103 comment "MX1 platforms:"
 104
 105 config MACH_SCB9328
 106         bool "Synertronixx scb9328"
 107         select IMX_HAVE_PLATFORM_IMX_UART
 108         select SOC_IMX1
 109         help
 110           Say Y here if you are using a Synertronixx scb9328 board
 111
 112 config MACH_APF9328
 113         bool "APF9328"
 114         select IMX_HAVE_PLATFORM_IMX_I2C
 115         select IMX_HAVE_PLATFORM_IMX_UART
 116         select SOC_IMX1
 117         help
 118           Say Yes here if you are using the Armadeus APF9328 development board
 119
 120 config MACH_IMX1_DT
 121         bool "Support i.MX1 platforms from device tree"
 122         select SOC_IMX1
 123         help
 124           Include support for Freescale i.MX1 based platforms
 125           using the device tree for discovery.
 126
 127 endif
 128
 129 if ARCH_MULTI_V5
 130
 131 comment "MX21 platforms:"
 132
 133 config MACH_MX21ADS
 134         bool "MX21ADS platform"
 135         select IMX_HAVE_PLATFORM_IMX_FB
 136         select IMX_HAVE_PLATFORM_IMX_UART
 137         select IMX_HAVE_PLATFORM_MXC_MMC
 138         select IMX_HAVE_PLATFORM_MXC_NAND
 139         select SOC_IMX21
 140         help
 141           Include support for MX21ADS platform. This includes specific
 142           configurations for the board and its peripherals.
 143
 144 comment "MX27 platforms:"
 145
 146 config MACH_MX27ADS
 147         bool "MX27ADS platform"
 148         select IMX_HAVE_PLATFORM_IMX_FB
 149         select IMX_HAVE_PLATFORM_IMX_I2C
 150         select IMX_HAVE_PLATFORM_IMX_UART
 151         select IMX_HAVE_PLATFORM_MXC_MMC
 152         select IMX_HAVE_PLATFORM_MXC_NAND
 153         select IMX_HAVE_PLATFORM_MXC_W1
 154         select SOC_IMX27
 155         help
 156           Include support for MX27ADS platform. This includes specific
 157           configurations for the board and its peripherals.
 158
 159 config MACH_MX27_3DS
 160         bool "MX27PDK platform"
 161         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 162         select IMX_HAVE_PLATFORM_IMX2_WDT
 163         select IMX_HAVE_PLATFORM_IMX_FB
 164         select IMX_HAVE_PLATFORM_IMX_I2C
 165         select IMX_HAVE_PLATFORM_IMX_KEYPAD
 166         select IMX_HAVE_PLATFORM_IMX_SSI
 167         select IMX_HAVE_PLATFORM_IMX_UART
 168         select IMX_HAVE_PLATFORM_MX2_CAMERA
 169         select IMX_HAVE_PLATFORM_MXC_EHCI
 170         select IMX_HAVE_PLATFORM_MXC_MMC
 171         select IMX_HAVE_PLATFORM_SPI_IMX
 172         select MXC_DEBUG_BOARD
 173         select USB_ULPI_VIEWPORT if USB_ULPI
 174         select SOC_IMX27
 175         help
 176           Include support for MX27PDK platform. This includes specific
 177           configurations for the board and its peripherals.
 178
 179 config MACH_IMX27_VISSTRIM_M10
 180         bool "Vista Silicon i.MX27 Visstrim_m10"
 181         select IMX_HAVE_PLATFORM_GPIO_KEYS
 182         select IMX_HAVE_PLATFORM_IMX_I2C
 183         select IMX_HAVE_PLATFORM_IMX_SSI
 184         select IMX_HAVE_PLATFORM_IMX_UART
 185         select IMX_HAVE_PLATFORM_MX2_CAMERA
 186         select IMX_HAVE_PLATFORM_MX2_EMMA
 187         select IMX_HAVE_PLATFORM_MXC_EHCI
 188         select IMX_HAVE_PLATFORM_MXC_MMC
 189         select LEDS_GPIO_REGISTER
 190         select SOC_IMX27
 191         help
 192           Include support for Visstrim_m10 platform and its different variants.
 193           This includes specific configurations for the board and its
 194           peripherals.
 195
 196 config MACH_PCA100
 197         bool "Phytec phyCARD-s (pca100)"
 198         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 199         select IMX_HAVE_PLATFORM_IMX2_WDT
 200         select IMX_HAVE_PLATFORM_IMX_FB
 201         select IMX_HAVE_PLATFORM_IMX_I2C
 202         select IMX_HAVE_PLATFORM_IMX_SSI
 203         select IMX_HAVE_PLATFORM_IMX_UART
 204         select IMX_HAVE_PLATFORM_MXC_EHCI
 205         select IMX_HAVE_PLATFORM_MXC_MMC
 206         select IMX_HAVE_PLATFORM_MXC_NAND
 207         select IMX_HAVE_PLATFORM_MXC_W1
 208         select IMX_HAVE_PLATFORM_SPI_IMX
 209         select USB_ULPI_VIEWPORT if USB_ULPI
 210         select SOC_IMX27
 211         help
 212           Include support for phyCARD-s (aka pca100) platform. This
 213           includes specific configurations for the module and its peripherals.
 214
 215 config MACH_IMX27_DT
 216         bool "Support i.MX27 platforms from device tree"
 217         select SOC_IMX27
 218         help
 219           Include support for Freescale i.MX27 based platforms
 220           using the device tree for discovery
 221
 222 endif
 223
 224 if ARCH_MULTI_V6
 225
 226 comment "MX31 platforms:"
 227
 228 config MACH_MX31ADS
 229         bool "Support MX31ADS platforms"
 230         default y
 231         select IMX_HAVE_PLATFORM_IMX_I2C
 232         select IMX_HAVE_PLATFORM_IMX_SSI
 233         select IMX_HAVE_PLATFORM_IMX_UART
 234         select SOC_IMX31
 235         help
 236           Include support for MX31ADS platform. This includes specific
 237           configurations for the board and its peripherals.
 238
 239 config MACH_MX31ADS_WM1133_EV1
 240         bool "Support Wolfson Microelectronics 1133-EV1 module"
 241         depends on MACH_MX31ADS
 242         depends on MFD_WM8350_I2C
 243         depends on REGULATOR_WM8350 = y
 244         help
 245           Include support for the Wolfson Microelectronics 1133-EV1 PMU
 246           and audio module for the MX31ADS platform.
 247
 248 config MACH_MX31LILLY
 249         bool "Support MX31 LILLY-1131 platforms (INCO startec)"
 250         select IMX_HAVE_PLATFORM_IMX_UART
 251         select IMX_HAVE_PLATFORM_IPU_CORE
 252         select IMX_HAVE_PLATFORM_MXC_EHCI
 253         select IMX_HAVE_PLATFORM_MXC_MMC
 254         select IMX_HAVE_PLATFORM_SPI_IMX
 255         select USB_ULPI_VIEWPORT if USB_ULPI
 256         select SOC_IMX31
 257         help
 258           Include support for mx31 based LILLY1131 modules. This includes
 259           specific configurations for the board and its peripherals.
 260
 261 config MACH_MX31LITE
 262         bool "Support MX31 LITEKIT (LogicPD)"
 263         select IMX_HAVE_PLATFORM_IMX2_WDT
 264         select IMX_HAVE_PLATFORM_IMX_UART
 265         select IMX_HAVE_PLATFORM_MXC_EHCI
 266         select IMX_HAVE_PLATFORM_MXC_MMC
 267         select IMX_HAVE_PLATFORM_MXC_NAND
 268         select IMX_HAVE_PLATFORM_MXC_RTC
 269         select IMX_HAVE_PLATFORM_SPI_IMX
 270         select LEDS_GPIO_REGISTER
 271         select USB_ULPI_VIEWPORT if USB_ULPI
 272         select SOC_IMX31
 273         help
 274           Include support for MX31 LITEKIT platform. This includes specific
 275           configurations for the board and its peripherals.
 276
 277 config MACH_PCM037
 278         bool "Support Phytec pcm037 (i.MX31) platforms"
 279         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 280         select IMX_HAVE_PLATFORM_IMX2_WDT
 281         select IMX_HAVE_PLATFORM_IMX_I2C
 282         select IMX_HAVE_PLATFORM_IMX_UART
 283         select IMX_HAVE_PLATFORM_IPU_CORE
 284         select IMX_HAVE_PLATFORM_MXC_EHCI
 285         select IMX_HAVE_PLATFORM_MXC_MMC
 286         select IMX_HAVE_PLATFORM_MXC_NAND
 287         select IMX_HAVE_PLATFORM_MXC_W1
 288         select USB_ULPI_VIEWPORT if USB_ULPI
 289         select SOC_IMX31
 290         help
 291           Include support for Phytec pcm037 platform. This includes
 292           specific configurations for the board and its peripherals.
 293
 294 config MACH_PCM037_EET
 295         bool "Support pcm037 EET board extensions"
 296         depends on MACH_PCM037
 297         select IMX_HAVE_PLATFORM_GPIO_KEYS
 298         select IMX_HAVE_PLATFORM_SPI_IMX
 299         help
 300           Add support for PCM037 EET baseboard extensions. If you are using the
 301           OLED display with EET, use "video=mx3fb:CMEL-OLED" kernel
 302           command-line parameter.
 303
 304 config MACH_MX31_3DS
 305         bool "Support MX31PDK (3DS)"
 306         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 307         select IMX_HAVE_PLATFORM_IMX2_WDT
 308         select IMX_HAVE_PLATFORM_IMX_I2C
 309         select IMX_HAVE_PLATFORM_IMX_KEYPAD
 310         select IMX_HAVE_PLATFORM_IMX_SSI
 311         select IMX_HAVE_PLATFORM_IMX_UART
 312         select IMX_HAVE_PLATFORM_IPU_CORE
 313         select IMX_HAVE_PLATFORM_MXC_EHCI
 314         select IMX_HAVE_PLATFORM_MXC_MMC
 315         select IMX_HAVE_PLATFORM_MXC_NAND
 316         select IMX_HAVE_PLATFORM_SPI_IMX
 317         select MXC_DEBUG_BOARD
 318         select USB_ULPI_VIEWPORT if USB_ULPI
 319         select SOC_IMX31
 320         help
 321           Include support for MX31PDK (3DS) platform. This includes specific
 322           configurations for the board and its peripherals.
 323
 324 config MACH_MX31_3DS_MXC_NAND_USE_BBT
 325         bool "Make the MXC NAND driver use the in flash Bad Block Table"
 326         depends on MACH_MX31_3DS
 327         depends on MTD_NAND_MXC
 328         help
 329           Enable this if you want that the MXC NAND driver uses the in flash
 330           Bad Block Table to know what blocks are bad instead of scanning the
 331           entire flash looking for bad block markers.
 332
 333 config MACH_MX31MOBOARD
 334         bool "Support mx31moboard platforms (EPFL Mobots group)"
 335         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 336         select IMX_HAVE_PLATFORM_IMX2_WDT
 337         select IMX_HAVE_PLATFORM_IMX_I2C
 338         select IMX_HAVE_PLATFORM_IMX_SSI
 339         select IMX_HAVE_PLATFORM_IMX_UART
 340         select IMX_HAVE_PLATFORM_IPU_CORE
 341         select IMX_HAVE_PLATFORM_MXC_EHCI
 342         select IMX_HAVE_PLATFORM_MXC_MMC
 343         select IMX_HAVE_PLATFORM_SPI_IMX
 344         select LEDS_GPIO_REGISTER
 345         select USB_ULPI_VIEWPORT if USB_ULPI
 346         select SOC_IMX31
 347         help
 348           Include support for mx31moboard platform. This includes specific
 349           configurations for the board and its peripherals.
 350
 351 config MACH_QONG
 352         bool "Support Dave/DENX QongEVB-LITE platform"
 353         select IMX_HAVE_PLATFORM_IMX2_WDT
 354         select IMX_HAVE_PLATFORM_IMX_UART
 355         select SOC_IMX31
 356         help
 357           Include support for Dave/DENX QongEVB-LITE platform. This includes
 358           specific configurations for the board and its peripherals.
 359
 360 config MACH_ARMADILLO5X0
 361         bool "Support Atmark Armadillo-500 Development Base Board"
 362         select IMX_HAVE_PLATFORM_GPIO_KEYS
 363         select IMX_HAVE_PLATFORM_IMX_I2C
 364         select IMX_HAVE_PLATFORM_IMX_UART
 365         select IMX_HAVE_PLATFORM_IPU_CORE
 366         select IMX_HAVE_PLATFORM_MXC_EHCI
 367         select IMX_HAVE_PLATFORM_MXC_MMC
 368         select IMX_HAVE_PLATFORM_MXC_NAND
 369         select USB_ULPI_VIEWPORT if USB_ULPI
 370         select SOC_IMX31
 371         help
 372           Include support for Atmark Armadillo-500 platform. This includes
 373           specific configurations for the board and its peripherals.
 374
 375 config MACH_KZM_ARM11_01
 376         bool "Support KZM-ARM11-01(Kyoto Microcomputer)"
 377         select IMX_HAVE_PLATFORM_IMX_UART
 378         select SOC_IMX31
 379         help
 380           Include support for KZM-ARM11-01. This includes specific
 381           configurations for the board and its peripherals.
 382
 383 config MACH_BUG
 384         bool "Support Buglabs BUGBase platform"
 385         default y
 386         select IMX_HAVE_PLATFORM_IMX_UART
 387         select SOC_IMX31
 388         help
 389           Include support for BUGBase 1.3 platform. This includes specific
 390           configurations for the board and its peripherals.
 391
 392 config MACH_IMX31_DT
 393         bool "Support i.MX31 platforms from device tree"
 394         select SOC_IMX31
 395         help
 396           Include support for Freescale i.MX31 based platforms
 397           using the device tree for discovery.
 398
 399 comment "MX35 platforms:"
 400
 401 config MACH_IMX35_DT
 402         bool "Support i.MX35 platforms from device tree"
 403         select SOC_IMX35
 404         help
 405           Include support for Freescale i.MX35 based platforms
 406           using the device tree for discovery.
 407
 408 config MACH_PCM043
 409         bool "Support Phytec pcm043 (i.MX35) platforms"
 410         select IMX_HAVE_PLATFORM_FLEXCAN
 411         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 412         select IMX_HAVE_PLATFORM_IMX2_WDT
 413         select IMX_HAVE_PLATFORM_IMX_I2C
 414         select IMX_HAVE_PLATFORM_IMX_SSI
 415         select IMX_HAVE_PLATFORM_IMX_UART
 416         select IMX_HAVE_PLATFORM_IPU_CORE
 417         select IMX_HAVE_PLATFORM_MXC_EHCI
 418         select IMX_HAVE_PLATFORM_MXC_NAND
 419         select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
 420         select USB_ULPI_VIEWPORT if USB_ULPI
 421         select SOC_IMX35
 422         help
 423           Include support for Phytec pcm043 platform. This includes
 424           specific configurations for the board and its peripherals.
 425
 426 config MACH_MX35_3DS
 427         bool "Support MX35PDK platform"
 428         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 429         select IMX_HAVE_PLATFORM_IMX2_WDT
 430         select IMX_HAVE_PLATFORM_IMX_FB
 431         select IMX_HAVE_PLATFORM_IMX_I2C
 432         select IMX_HAVE_PLATFORM_IMX_UART
 433         select IMX_HAVE_PLATFORM_IPU_CORE
 434         select IMX_HAVE_PLATFORM_MXC_EHCI
 435         select IMX_HAVE_PLATFORM_MXC_NAND
 436         select IMX_HAVE_PLATFORM_MXC_RTC
 437         select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
 438         select MXC_DEBUG_BOARD
 439         select SOC_IMX35
 440         help
 441           Include support for MX35PDK platform. This includes specific
 442           configurations for the board and its peripherals.
 443
 444 config MACH_VPR200
 445         bool "Support VPR200 platform"
 446         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 447         select IMX_HAVE_PLATFORM_GPIO_KEYS
 448         select IMX_HAVE_PLATFORM_IMX2_WDT
 449         select IMX_HAVE_PLATFORM_IMX_I2C
 450         select IMX_HAVE_PLATFORM_IMX_UART
 451         select IMX_HAVE_PLATFORM_IPU_CORE
 452         select IMX_HAVE_PLATFORM_MXC_EHCI
 453         select IMX_HAVE_PLATFORM_MXC_NAND
 454         select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
 455         select SOC_IMX35
 456         help
 457           Include support for VPR200 platform. This includes specific
 458           configurations for the board and its peripherals.
 459
 460 endif
 461
 462 comment "Device tree only"
 463
 464 if ARCH_MULTI_V5
 465
 466 config SOC_IMX25
 467         bool "i.MX25 support"
 468         select ARCH_MXC_IOMUX_V3
 469         select CPU_ARM926T
 470         select MXC_AVIC
 471         select PINCTRL_IMX25
 472         help
 473           This enables support for Freescale i.MX25 processor
 474 endif
 475
 476 if ARCH_MULTI_V7
 477
 478 comment "Cortex-A platforms"
 479
 480 config SOC_IMX5
 481         bool
 482         select HAVE_IMX_SRC
 483         select MXC_TZIC
 484
 485 config  SOC_IMX50
 486         bool "i.MX50 support"
 487         select PINCTRL_IMX50
 488         select SOC_IMX5
 489
 490         help
 491           This enables support for Freescale i.MX50 processor.
 492
 493 config SOC_IMX51
 494         bool "i.MX51 support"
 495         select PINCTRL_IMX51
 496         select SOC_IMX5
 497         help
 498           This enables support for Freescale i.MX51 processor
 499
 500 config  SOC_IMX53
 501         bool "i.MX53 support"
 502         select PINCTRL_IMX53
 503         select SOC_IMX5
 504
 505         help
 506           This enables support for Freescale i.MX53 processor.
 507
 508 config SOC_IMX6
 509         bool
 510         select ARM_CPU_SUSPEND if PM
 511         select ARM_ERRATA_754322
 512         select ARM_ERRATA_775420
 513         select ARM_GIC
 514         select HAVE_IMX_ANATOP
 515         select HAVE_IMX_GPC
 516         select HAVE_IMX_MMDC
 517         select HAVE_IMX_SRC
 518         select MFD_SYSCON
 519         select PL310_ERRATA_769419 if CACHE_L2X0
 520
 521 config SOC_IMX6Q
 522         bool "i.MX6 Quad/DualLite support"
 523         select ARM_ERRATA_764369 if SMP
 524         select HAVE_ARM_SCU if SMP
 525         select HAVE_ARM_TWD
 526         select PCI_DOMAINS if PCI
 527         select PINCTRL_IMX6Q
 528         select SOC_IMX6
 529
 530         help
 531           This enables support for Freescale i.MX6 Quad processor.
 532
 533 config SOC_IMX6SL
 534         bool "i.MX6 SoloLite support"
 535         select PINCTRL_IMX6SL
 536         select SOC_IMX6
 537
 538         help
 539           This enables support for Freescale i.MX6 SoloLite processor.
 540
 541 config SOC_IMX6SX
 542         bool "i.MX6 SoloX support"
 543         select PINCTRL_IMX6SX
 544         select SOC_IMX6
 545
 546         help
 547           This enables support for Freescale i.MX6 SoloX processor.
 548
 549 config SOC_IMX6UL
 550         bool "i.MX6 UltraLite support"
 551         select PINCTRL_IMX6UL
 552         select SOC_IMX6
 553
 554         help
 555           This enables support for Freescale i.MX6 UltraLite processor.
 556
 557 config SOC_IMX7D
 558         bool "i.MX7 Dual support"
 559         select PINCTRL_IMX7D
 560         select ARM_GIC
 561         select HAVE_ARM_ARCH_TIMER
 562         select HAVE_IMX_ANATOP
 563         select HAVE_IMX_MMDC
 564         select HAVE_IMX_SRC
 565         help
 566                 This enables support for Freescale i.MX7 Dual processor.
 567
 568 config SOC_LS1021A
 569         bool "Freescale LS1021A support"
 570         select ARM_GIC
 571         select HAVE_ARM_ARCH_TIMER
 572         select PCI_DOMAINS if PCI
 573         select ZONE_DMA if ARM_LPAE
 574         help
 575           This enables support for Freescale LS1021A processor.
 576
 577 endif
 578
 579 comment "Cortex-A/Cortex-M asymmetric multiprocessing platforms"
 580
 581 if ARCH_MULTI_V7 || ARM_SINGLE_ARMV7M
 582
 583 config SOC_VF610
 584         bool "Vybrid Family VF610 support"
 585         select ARM_GIC if ARCH_MULTI_V7
 586         select PINCTRL_VF610
 587         select PL310_ERRATA_769419 if CACHE_L2X0
 588         select SMP_ON_UP if SMP
 589
 590         help
 591           This enables support for Freescale Vybrid VF610 processor.
 592
 593 choice
 594         prompt "Clocksource for scheduler clock"
 595         depends on SOC_VF610
 596         default VF_USE_ARM_GLOBAL_TIMER
 597
 598         config VF_USE_ARM_GLOBAL_TIMER
 599                 bool "Use ARM Global Timer"
 600                 depends on ARCH_MULTI_V7
 601                 select ARM_GLOBAL_TIMER
 602                 select CLKSRC_ARM_GLOBAL_TIMER_SCHED_CLOCK
 603                 help
 604                   Use the ARM Global Timer as clocksource
 605
 606         config VF_USE_PIT_TIMER
 607                 bool "Use PIT timer"
 608                 select VF_PIT_TIMER
 609                 help
 610                   Use SoC Periodic Interrupt Timer (PIT) as clocksource
 611
 612 endchoice
 613
 614 endif
 615
 616 source "arch/arm/mach-imx/devices/Kconfig"
 617
 618 endif