drivers/gpu/drm/bridge/parade-ps8622.c

   1 /*
   2  * Parade PS8622 eDP/LVDS bridge driver
   3  *
   4  * Copyright (C) 2014 Google, Inc.
   5  *
   6  * This software is licensed under the terms of the GNU General Public
   7  * License version 2, as published by the Free Software Foundation, and
   8  * may be copied, distributed, and modified under those terms.
   9  *
  10  * This program is distributed in the hope that it will be useful,
  11  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  12  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  13  * GNU General Public License for more details.
  14  */
  15
  16 #include <linux/backlight.h>
  17 #include <linux/delay.h>
  18 #include <linux/err.h>
  19 #include <linux/gpio.h>
  20 #include <linux/gpio/consumer.h>
  21 #include <linux/i2c.h>
  22 #include <linux/module.h>
  23 #include <linux/of.h>
  24 #include <linux/of_device.h>
  25 #include <linux/of_graph.h>
  26 #include <linux/pm.h>
  27 #include <linux/regulator/consumer.h>
  28
  29 #include <drm/drm_panel.h>
  30
  31 #include "drmP.h"
  32 #include "drm_crtc.h"
  33 #include "drm_crtc_helper.h"
  34 #include "drm_atomic_helper.h"
  35
  36 /* Brightness scale on the Parade chip */
  37 #define PS8622_MAX_BRIGHTNESS 0xff
  38
  39 /* Timings taken from the version 1.7 datasheet for the PS8622/PS8625 */
  40 #define PS8622_POWER_RISE_T1_MIN_US 10
  41 #define PS8622_POWER_RISE_T1_MAX_US 10000
  42 #define PS8622_RST_HIGH_T2_MIN_US 3000
  43 #define PS8622_RST_HIGH_T2_MAX_US 30000
  44 #define PS8622_PWMO_END_T12_MS 200
  45 #define PS8622_POWER_FALL_T16_MAX_US 10000
  46 #define PS8622_POWER_OFF_T17_MS 500
  47
  48 #if ((PS8622_RST_HIGH_T2_MIN_US + PS8622_POWER_RISE_T1_MAX_US) > \
  49         (PS8622_RST_HIGH_T2_MAX_US + PS8622_POWER_RISE_T1_MIN_US))
  50 #error "T2.min + T1.max must be less than T2.max + T1.min"
  51 #endif
  52
  53 struct ps8622_bridge {
  54         struct drm_connector connector;
  55         struct i2c_client *client;
  56         struct drm_bridge bridge;
  57         struct drm_panel *panel;
  58         struct regulator *v12;
  59         struct backlight_device *bl;
  60
  61         struct gpio_desc *gpio_slp;
  62         struct gpio_desc *gpio_rst;
  63
  64         u32 max_lane_count;
  65         u32 lane_count;
  66
  67         bool enabled;
  68 };
  69
  70 static inline struct ps8622_bridge *
  71                 bridge_to_ps8622(struct drm_bridge *bridge)
  72 {
  73         return container_of(bridge, struct ps8622_bridge, bridge);
  74 }
  75
  76 static inline struct ps8622_bridge *
  77                 connector_to_ps8622(struct drm_connector *connector)
  78 {
  79         return container_of(connector, struct ps8622_bridge, connector);
  80 }
  81
  82 static int ps8622_set(struct i2c_client *client, u8 page, u8 reg, u8 val)
  83 {
  84         int ret;
  85         struct i2c_adapter *adap = client->adapter;
  86         struct i2c_msg msg;
  87         u8 data[] = {reg, val};
  88
  89         msg.addr = client->addr + page;
  90         msg.flags = 0;
  91         msg.len = sizeof(data);
  92         msg.buf = data;
  93
  94         ret = i2c_transfer(adap, &msg, 1);
  95         if (ret != 1)
  96                 pr_warn("PS8622 I2C write (0x%02x,0x%02x,0x%02x) failed: %d\n",
  97                         client->addr + page, reg, val, ret);
  98         return !(ret == 1);
  99 }
 100
 101 static int ps8622_send_config(struct ps8622_bridge *ps8622)
 102 {
 103         struct i2c_client *cl = ps8622->client;
 104         int err = 0;
 105
 106         /* HPD low */
 107         err = ps8622_set(cl, 0x02, 0xa1, 0x01);
 108         if (err)
 109                 goto error;
 110
 111         /* SW setting: [1:0] SW output 1.2V voltage is lower to 96% */
 112         err = ps8622_set(cl, 0x04, 0x14, 0x01);
 113         if (err)
 114                 goto error;
 115
 116         /* RCO SS setting: [5:4] = b01 0.5%, b10 1%, b11 1.5% */
 117         err = ps8622_set(cl, 0x04, 0xe3, 0x20);
 118         if (err)
 119                 goto error;
 120
 121         /* [7] RCO SS enable */
 122         err = ps8622_set(cl, 0x04, 0xe2, 0x80);
 123         if (err)
 124                 goto error;
 125
 126         /* RPHY Setting
 127          * [3:2] CDR tune wait cycle before measure for fine tune
 128          * b00: 1us b01: 0.5us b10:2us, b11: 4us
 129          */
 130         err = ps8622_set(cl, 0x04, 0x8a, 0x0c);
 131         if (err)
 132                 goto error;
 133
 134         /* [3] RFD always on */
 135         err = ps8622_set(cl, 0x04, 0x89, 0x08);
 136         if (err)
 137                 goto error;
 138
 139         /* CTN lock in/out: 20000ppm/80000ppm. Lock out 2 times. */
 140         err = ps8622_set(cl, 0x04, 0x71, 0x2d);
 141         if (err)
 142                 goto error;
 143
 144         /* 2.7G CDR settings: NOF=40LSB for HBR CDR  setting */
 145         err = ps8622_set(cl, 0x04, 0x7d, 0x07);
 146         if (err)
 147                 goto error;
 148
 149         /* [1:0] Fmin=+4bands */
 150         err = ps8622_set(cl, 0x04, 0x7b, 0x00);
 151         if (err)
 152                 goto error;
 153
 154         /* [7:5] DCO_FTRNG=+-40% */
 155         err = ps8622_set(cl, 0x04, 0x7a, 0xfd);
 156         if (err)
 157                 goto error;
 158
 159         /* 1.62G CDR settings: [5:2]NOF=64LSB [1:0]DCO scale is 2/5 */
 160         err = ps8622_set(cl, 0x04, 0xc0, 0x12);
 161         if (err)
 162                 goto error;
 163
 164         /* Gitune=-37% */
 165         err = ps8622_set(cl, 0x04, 0xc1, 0x92);
 166         if (err)
 167                 goto error;
 168
 169         /* Fbstep=100% */
 170         err = ps8622_set(cl, 0x04, 0xc2, 0x1c);
 171         if (err)
 172                 goto error;
 173
 174         /* [7] LOS signal disable */
 175         err = ps8622_set(cl, 0x04, 0x32, 0x80);
 176         if (err)
 177                 goto error;
 178
 179         /* RPIO Setting: [7:4] LVDS driver bias current : 75% (250mV swing) */
 180         err = ps8622_set(cl, 0x04, 0x00, 0xb0);
 181         if (err)
 182                 goto error;
 183
 184         /* [7:6] Right-bar GPIO output strength is 8mA */
 185         err = ps8622_set(cl, 0x04, 0x15, 0x40);
 186         if (err)
 187                 goto error;
 188
 189         /* EQ Training State Machine Setting, RCO calibration start */
 190         err = ps8622_set(cl, 0x04, 0x54, 0x10);
 191         if (err)
 192                 goto error;
 193
 194         /* Logic, needs more than 10 I2C command */
 195         /* [4:0] MAX_LANE_COUNT set to max supported lanes */
 196         err = ps8622_set(cl, 0x01, 0x02, 0x80 | ps8622->max_lane_count);
 197         if (err)
 198                 goto error;
 199
 200         /* [4:0] LANE_COUNT_SET set to chosen lane count */
 201         err = ps8622_set(cl, 0x01, 0x21, 0x80 | ps8622->lane_count);
 202         if (err)
 203                 goto error;
 204
 205         err = ps8622_set(cl, 0x00, 0x52, 0x20);
 206         if (err)
 207                 goto error;
 208
 209         /* HPD CP toggle enable */
 210         err = ps8622_set(cl, 0x00, 0xf1, 0x03);
 211         if (err)
 212                 goto error;
 213
 214         err = ps8622_set(cl, 0x00, 0x62, 0x41);
 215         if (err)
 216                 goto error;
 217
 218         /* Counter number, add 1ms counter delay */
 219         err = ps8622_set(cl, 0x00, 0xf6, 0x01);
 220         if (err)
 221                 goto error;
 222
 223         /* [6]PWM function control by DPCD0040f[7], default is PWM block */
 224         err = ps8622_set(cl, 0x00, 0x77, 0x06);
 225         if (err)
 226                 goto error;
 227
 228         /* 04h Adjust VTotal toleranceto fix the 30Hz no display issue */
 229         err = ps8622_set(cl, 0x00, 0x4c, 0x04);
 230         if (err)
 231                 goto error;
 232
 233         /* DPCD00400='h00, Parade OUI ='h001cf8 */
 234         err = ps8622_set(cl, 0x01, 0xc0, 0x00);
 235         if (err)
 236                 goto error;
 237
 238         /* DPCD00401='h1c */
 239         err = ps8622_set(cl, 0x01, 0xc1, 0x1c);
 240         if (err)
 241                 goto error;
 242
 243         /* DPCD00402='hf8 */
 244         err = ps8622_set(cl, 0x01, 0xc2, 0xf8);
 245         if (err)
 246                 goto error;
 247
 248         /* DPCD403~408 = ASCII code, D2SLV5='h4432534c5635 */
 249         err = ps8622_set(cl, 0x01, 0xc3, 0x44);
 250         if (err)
 251                 goto error;
 252
 253         /* DPCD404 */
 254         err = ps8622_set(cl, 0x01, 0xc4, 0x32);
 255         if (err)
 256                 goto error;
 257
 258         /* DPCD405 */
 259         err = ps8622_set(cl, 0x01, 0xc5, 0x53);
 260         if (err)
 261                 goto error;
 262
 263         /* DPCD406 */
 264         err = ps8622_set(cl, 0x01, 0xc6, 0x4c);
 265         if (err)
 266                 goto error;
 267
 268         /* DPCD407 */
 269         err = ps8622_set(cl, 0x01, 0xc7, 0x56);
 270         if (err)
 271                 goto error;
 272
 273         /* DPCD408 */
 274         err = ps8622_set(cl, 0x01, 0xc8, 0x35);
 275         if (err)
 276                 goto error;
 277
 278         /* DPCD40A, Initial Code major revision '01' */
 279         err = ps8622_set(cl, 0x01, 0xca, 0x01);
 280         if (err)
 281                 goto error;
 282
 283         /* DPCD40B, Initial Code minor revision '05' */
 284         err = ps8622_set(cl, 0x01, 0xcb, 0x05);
 285         if (err)
 286                 goto error;
 287
 288
 289         if (ps8622->bl) {
 290                 /* DPCD720, internal PWM */
 291                 err = ps8622_set(cl, 0x01, 0xa5, 0xa0);
 292                 if (err)
 293                         goto error;
 294
 295                 /* FFh for 100% brightness, 0h for 0% brightness */
 296                 err = ps8622_set(cl, 0x01, 0xa7,
 297                                 ps8622->bl->props.brightness);
 298                 if (err)
 299                         goto error;
 300         } else {
 301                 /* DPCD720, external PWM */
 302                 err = ps8622_set(cl, 0x01, 0xa5, 0x80);
 303                 if (err)
 304                         goto error;
 305         }
 306
 307         /* Set LVDS output as 6bit-VESA mapping, single LVDS channel */
 308         err = ps8622_set(cl, 0x01, 0xcc, 0x13);
 309         if (err)
 310                 goto error;
 311
 312         /* Enable SSC set by register */
 313         err = ps8622_set(cl, 0x02, 0xb1, 0x20);
 314         if (err)
 315                 goto error;
 316
 317         /* Set SSC enabled and +/-1% central spreading */
 318         err = ps8622_set(cl, 0x04, 0x10, 0x16);
 319         if (err)
 320                 goto error;
 321
 322         /* Logic end */
 323         /* MPU Clock source: LC => RCO */
 324         err = ps8622_set(cl, 0x04, 0x59, 0x60);
 325         if (err)
 326                 goto error;
 327
 328         /* LC -> RCO */
 329         err = ps8622_set(cl, 0x04, 0x54, 0x14);
 330         if (err)
 331                 goto error;
 332
 333         /* HPD high */
 334         err = ps8622_set(cl, 0x02, 0xa1, 0x91);
 335
 336 error:
 337         return err ? -EIO : 0;
 338 }
 339
 340 static int ps8622_backlight_update(struct backlight_device *bl)
 341 {
 342         struct ps8622_bridge *ps8622 = dev_get_drvdata(&bl->dev);
 343         int ret, brightness = bl->props.brightness;
 344
 345         if (bl->props.power != FB_BLANK_UNBLANK ||
 346             bl->props.state & (BL_CORE_SUSPENDED | BL_CORE_FBBLANK))
 347                 brightness = 0;
 348
 349         if (!ps8622->enabled)
 350                 return -EINVAL;
 351
 352         ret = ps8622_set(ps8622->client, 0x01, 0xa7, brightness);
 353
 354         return ret;
 355 }
 356
 357 static const struct backlight_ops ps8622_backlight_ops = {
 358         .update_status  = ps8622_backlight_update,
 359 };
 360
 361 static void ps8622_pre_enable(struct drm_bridge *bridge)
 362 {
 363         struct ps8622_bridge *ps8622 = bridge_to_ps8622(bridge);
 364         int ret;
 365
 366         if (ps8622->enabled)
 367                 return;
 368
 369         gpiod_set_value(ps8622->gpio_rst, 0);
 370
 371         if (ps8622->v12) {
 372                 ret = regulator_enable(ps8622->v12);
 373                 if (ret)
 374                         DRM_ERROR("fails to enable ps8622->v12");
 375         }
 376
 377         if (drm_panel_prepare(ps8622->panel)) {
 378                 DRM_ERROR("failed to prepare panel\n");
 379                 return;
 380         }
 381
 382         gpiod_set_value(ps8622->gpio_slp, 1);
 383
 384         /*
 385          * T1 is the range of time that it takes for the power to rise after we
 386          * enable the lcd/ps8622 fet. T2 is the range of time in which the
 387          * data sheet specifies we should deassert the reset pin.
 388          *
 389          * If it takes T1.max for the power to rise, we need to wait atleast
 390          * T2.min before deasserting the reset pin. If it takes T1.min for the
 391          * power to rise, we need to wait at most T2.max before deasserting the
 392          * reset pin.
 393          */
 394         usleep_range(PS8622_RST_HIGH_T2_MIN_US + PS8622_POWER_RISE_T1_MAX_US,
 395                      PS8622_RST_HIGH_T2_MAX_US + PS8622_POWER_RISE_T1_MIN_US);
 396
 397         gpiod_set_value(ps8622->gpio_rst, 1);
 398
 399         /* wait 20ms after RST high */
 400         usleep_range(20000, 30000);
 401
 402         ret = ps8622_send_config(ps8622);
 403         if (ret) {
 404                 DRM_ERROR("Failed to send config to bridge (%d)\n", ret);
 405                 return;
 406         }
 407
 408         ps8622->enabled = true;
 409 }
 410
 411 static void ps8622_enable(struct drm_bridge *bridge)
 412 {
 413         struct ps8622_bridge *ps8622 = bridge_to_ps8622(bridge);
 414
 415         if (drm_panel_enable(ps8622->panel)) {
 416                 DRM_ERROR("failed to enable panel\n");
 417                 return;
 418         }
 419 }
 420
 421 static void ps8622_disable(struct drm_bridge *bridge)
 422 {
 423         struct ps8622_bridge *ps8622 = bridge_to_ps8622(bridge);
 424
 425         if (drm_panel_disable(ps8622->panel)) {
 426                 DRM_ERROR("failed to disable panel\n");
 427                 return;
 428         }
 429         msleep(PS8622_PWMO_END_T12_MS);
 430 }
 431
 432 static void ps8622_post_disable(struct drm_bridge *bridge)
 433 {
 434         struct ps8622_bridge *ps8622 = bridge_to_ps8622(bridge);
 435
 436         if (!ps8622->enabled)
 437                 return;
 438
 439         ps8622->enabled = false;
 440
 441         /*
 442          * This doesn't matter if the regulators are turned off, but something
 443          * else might keep them on. In that case, we want to assert the slp gpio
 444          * to lower power.
 445          */
 446         gpiod_set_value(ps8622->gpio_slp, 0);
 447
 448         if (drm_panel_unprepare(ps8622->panel)) {
 449                 DRM_ERROR("failed to unprepare panel\n");
 450                 return;
 451         }
 452
 453         if (ps8622->v12)
 454                 regulator_disable(ps8622->v12);
 455
 456         /*
 457          * Sleep for at least the amount of time that it takes the power rail to
 458          * fall to prevent asserting the rst gpio from doing anything.
 459          */
 460         usleep_range(PS8622_POWER_FALL_T16_MAX_US,
 461                      2 * PS8622_POWER_FALL_T16_MAX_US);
 462         gpiod_set_value(ps8622->gpio_rst, 0);
 463
 464         msleep(PS8622_POWER_OFF_T17_MS);
 465 }
 466
 467 static int ps8622_get_modes(struct drm_connector *connector)
 468 {
 469         struct ps8622_bridge *ps8622;
 470
 471         ps8622 = connector_to_ps8622(connector);
 472
 473         return drm_panel_get_modes(ps8622->panel);
 474 }
 475
 476 static const struct drm_connector_helper_funcs ps8622_connector_helper_funcs = {
 477         .get_modes = ps8622_get_modes,
 478 };
 479
 480 static enum drm_connector_status ps8622_detect(struct drm_connector *connector,
 481                                                                 bool force)
 482 {
 483         return connector_status_connected;
 484 }
 485
 486 static void ps8622_connector_destroy(struct drm_connector *connector)
 487 {
 488         drm_connector_cleanup(connector);
 489 }
 490
 491 static const struct drm_connector_funcs ps8622_connector_funcs = {
 492         .dpms = drm_atomic_helper_connector_dpms,
 493         .fill_modes = drm_helper_probe_single_connector_modes,
 494         .detect = ps8622_detect,
 495         .destroy = ps8622_connector_destroy,
 496         .reset = drm_atomic_helper_connector_reset,
 497         .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
 498         .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
 499 };
 500
 501 static int ps8622_attach(struct drm_bridge *bridge)
 502 {
 503         struct ps8622_bridge *ps8622 = bridge_to_ps8622(bridge);
 504         int ret;
 505
 506         if (!bridge->encoder) {
 507                 DRM_ERROR("Parent encoder object not found");
 508                 return -ENODEV;
 509         }
 510
 511         ps8622->connector.polled = DRM_CONNECTOR_POLL_HPD;
 512         ret = drm_connector_init(bridge->dev, &ps8622->connector,
 513                         &ps8622_connector_funcs, DRM_MODE_CONNECTOR_LVDS);
 514         if (ret) {
 515                 DRM_ERROR("Failed to initialize connector with drm\n");
 516                 return ret;
 517         }
 518         drm_connector_helper_add(&ps8622->connector,
 519                                         &ps8622_connector_helper_funcs);
 520         drm_connector_register(&ps8622->connector);
 521         drm_mode_connector_attach_encoder(&ps8622->connector,
 522                                                         bridge->encoder);
 523
 524         if (ps8622->panel)
 525                 drm_panel_attach(ps8622->panel, &ps8622->connector);
 526
 527         drm_helper_hpd_irq_event(ps8622->connector.dev);
 528
 529         return ret;
 530 }
 531
 532 static const struct drm_bridge_funcs ps8622_bridge_funcs = {
 533         .pre_enable = ps8622_pre_enable,
 534         .enable = ps8622_enable,
 535         .disable = ps8622_disable,
 536         .post_disable = ps8622_post_disable,
 537         .attach = ps8622_attach,
 538 };
 539
 540 static const struct of_device_id ps8622_devices[] = {
 541         {.compatible = "parade,ps8622",},
 542         {.compatible = "parade,ps8625",},
 543         {}
 544 };
 545 MODULE_DEVICE_TABLE(of, ps8622_devices);
 546
 547 static int ps8622_probe(struct i2c_client *client,
 548                                         const struct i2c_device_id *id)
 549 {
 550         struct device *dev = &client->dev;
 551         struct device_node *endpoint, *panel_node;
 552         struct ps8622_bridge *ps8622;
 553         int ret;
 554
 555         ps8622 = devm_kzalloc(dev, sizeof(*ps8622), GFP_KERNEL);
 556         if (!ps8622)
 557                 return -ENOMEM;
 558
 559         endpoint = of_graph_get_next_endpoint(dev->of_node, NULL);
 560         if (endpoint) {
 561                 panel_node = of_graph_get_remote_port_parent(endpoint);
 562                 if (panel_node) {
 563                         ps8622->panel = of_drm_find_panel(panel_node);
 564                         of_node_put(panel_node);
 565                         if (!ps8622->panel)
 566                                 return -EPROBE_DEFER;
 567                 }
 568         }
 569
 570         ps8622->client = client;
 571
 572         ps8622->v12 = devm_regulator_get(dev, "vdd12");
 573         if (IS_ERR(ps8622->v12)) {
 574                 dev_info(dev, "no 1.2v regulator found for PS8622\n");
 575                 ps8622->v12 = NULL;
 576         }
 577
 578         ps8622->gpio_slp = devm_gpiod_get(dev, "sleep", GPIOD_OUT_HIGH);
 579         if (IS_ERR(ps8622->gpio_slp)) {
 580                 ret = PTR_ERR(ps8622->gpio_slp);
 581                 dev_err(dev, "cannot get gpio_slp %d\n", ret);
 582                 return ret;
 583         }
 584
 585         /*
 586          * Assert the reset pin high to avoid the bridge being
 587          * initialized prematurely
 588          */
 589         ps8622->gpio_rst = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
 590         if (IS_ERR(ps8622->gpio_rst)) {
 591                 ret = PTR_ERR(ps8622->gpio_rst);
 592                 dev_err(dev, "cannot get gpio_rst %d\n", ret);
 593                 return ret;
 594         }
 595
 596         ps8622->max_lane_count = id->driver_data;
 597
 598         if (of_property_read_u32(dev->of_node, "lane-count",
 599                                                 &ps8622->lane_count)) {
 600                 ps8622->lane_count = ps8622->max_lane_count;
 601         } else if (ps8622->lane_count > ps8622->max_lane_count) {
 602                 dev_info(dev, "lane-count property is too high,"
 603                                                 "using max_lane_count\n");
 604                 ps8622->lane_count = ps8622->max_lane_count;
 605         }
 606
 607         if (!of_find_property(dev->of_node, "use-external-pwm", NULL)) {
 608                 ps8622->bl = backlight_device_register("ps8622-backlight",
 609                                 dev, ps8622, &ps8622_backlight_ops,
 610                                 NULL);
 611                 if (IS_ERR(ps8622->bl)) {
 612                         DRM_ERROR("failed to register backlight\n");
 613                         ret = PTR_ERR(ps8622->bl);
 614                         ps8622->bl = NULL;
 615                         return ret;
 616                 }
 617                 ps8622->bl->props.max_brightness = PS8622_MAX_BRIGHTNESS;
 618                 ps8622->bl->props.brightness = PS8622_MAX_BRIGHTNESS;
 619         }
 620
 621         ps8622->bridge.funcs = &ps8622_bridge_funcs;
 622         ps8622->bridge.of_node = dev->of_node;
 623         ret = drm_bridge_add(&ps8622->bridge);
 624         if (ret) {
 625                 DRM_ERROR("Failed to add bridge\n");
 626                 return ret;
 627         }
 628
 629         i2c_set_clientdata(client, ps8622);
 630
 631         return 0;
 632 }
 633
 634 static int ps8622_remove(struct i2c_client *client)
 635 {
 636         struct ps8622_bridge *ps8622 = i2c_get_clientdata(client);
 637
 638         backlight_device_unregister(ps8622->bl);
 639         drm_bridge_remove(&ps8622->bridge);
 640
 641         return 0;
 642 }
 643
 644 static const struct i2c_device_id ps8622_i2c_table[] = {
 645         /* Device type, max_lane_count */
 646         {"ps8622", 1},
 647         {"ps8625", 2},
 648         {},
 649 };
 650 MODULE_DEVICE_TABLE(i2c, ps8622_i2c_table);
 651
 652 static struct i2c_driver ps8622_driver = {
 653         .id_table       = ps8622_i2c_table,
 654         .probe          = ps8622_probe,
 655         .remove         = ps8622_remove,
 656         .driver         = {
 657                 .name   = "ps8622",
 658                 .of_match_table = ps8622_devices,
 659         },
 660 };
 661 module_i2c_driver(ps8622_driver);
 662
 663 MODULE_AUTHOR("Vincent Palatin <vpalatin@chromium.org>");
 664 MODULE_DESCRIPTION("Parade ps8622/ps8625 eDP-LVDS converter driver");
 665 MODULE_LICENSE("GPL v2");