drivers/spi/Kconfig

   1 #
   2 # SPI driver configuration
   3 #
   4 # NOTE:  the reason this doesn't show SPI slave support is mostly that
   5 # nobody's needed a slave side API yet.  The master-role API is not
   6 # fully appropriate there, so it'd need some thought to do well.
   7 #
   8 menuconfig SPI
   9         bool "SPI support"
  10         depends on HAS_IOMEM
  11         help
  12           The "Serial Peripheral Interface" is a low level synchronous
  13           protocol.  Chips that support SPI can have data transfer rates
  14           up to several tens of Mbit/sec.  Chips are addressed with a
  15           controller and a chipselect.  Most SPI slaves don't support
  16           dynamic device discovery; some are even write-only or read-only.
  17
  18           SPI is widely used by microcontrollers to talk with sensors,
  19           eeprom and flash memory, codecs and various other controller
  20           chips, analog to digital (and d-to-a) converters, and more.
  21           MMC and SD cards can be accessed using SPI protocol; and for
  22           DataFlash cards used in MMC sockets, SPI must always be used.
  23
  24           SPI is one of a family of similar protocols using a four wire
  25           interface (select, clock, data in, data out) including Microwire
  26           (half duplex), SSP, SSI, and PSP.  This driver framework should
  27           work with most such devices and controllers.
  28
  29 if SPI
  30
  31 config SPI_DEBUG
  32         bool "Debug support for SPI drivers"
  33         depends on DEBUG_KERNEL
  34         help
  35           Say "yes" to enable debug messaging (like dev_dbg and pr_debug),
  36           sysfs, and debugfs support in SPI controller and protocol drivers.
  37
  38 #
  39 # MASTER side ... talking to discrete SPI slave chips including microcontrollers
  40 #
  41
  42 config SPI_MASTER
  43 #       bool "SPI Master Support"
  44         bool
  45         default SPI
  46         help
  47           If your system has an master-capable SPI controller (which
  48           provides the clock and chipselect), you can enable that
  49           controller and the protocol drivers for the SPI slave chips
  50           that are connected.
  51
  52 if SPI_MASTER
  53
  54 comment "SPI Master Controller Drivers"
  55
  56 config SPI_ALTERA
  57         tristate "Altera SPI Controller"
  58         select SPI_BITBANG
  59         help
  60           This is the driver for the Altera SPI Controller.
  61
  62 config SPI_ATH79
  63         tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
  64         depends on ATH79 && GPIOLIB
  65         select SPI_BITBANG
  66         help
  67           This enables support for the SPI controller present on the
  68           Atheros AR71XX/AR724X/AR913X SoCs.
  69
  70 config SPI_ATMEL
  71         tristate "Atmel SPI Controller"
  72         depends on HAS_DMA
  73         depends on (ARCH_AT91 || AVR32 || COMPILE_TEST)
  74         help
  75           This selects a driver for the Atmel SPI Controller, present on
  76           many AT32 (AVR32) and AT91 (ARM) chips.
  77
  78 config SPI_AU1550
  79         tristate "Au1550/Au1200/Au1300 SPI Controller"
  80         depends on MIPS_ALCHEMY
  81         select SPI_BITBANG
  82         help
  83           If you say yes to this option, support will be included for the
  84           PSC SPI controller found on Au1550, Au1200 and Au1300 series.
  85
  86 config SPI_AXI_SPI_ENGINE
  87         tristate "Analog Devices AXI SPI Engine controller"
  88         depends on HAS_IOMEM
  89         help
  90           This enables support for the Analog Devices AXI SPI Engine SPI controller.
  91           It is part of the SPI Engine framework that is used in some Analog Devices
  92           reference designs for FPGAs.
  93
  94 config SPI_BCM2835
  95         tristate "BCM2835 SPI controller"
  96         depends on GPIOLIB
  97         depends on ARCH_BCM2835 || COMPILE_TEST
  98         help
  99           This selects a driver for the Broadcom BCM2835 SPI master.
 100
 101           The BCM2835 contains two types of SPI master controller; the
 102           "universal SPI master", and the regular SPI controller. This driver
 103           is for the regular SPI controller. Slave mode operation is not also
 104           not supported.
 105
 106 config SPI_BCM2835AUX
 107         tristate "BCM2835 SPI auxiliary controller"
 108         depends on (ARCH_BCM2835 && GPIOLIB) || COMPILE_TEST
 109         help
 110           This selects a driver for the Broadcom BCM2835 SPI aux master.
 111
 112           The BCM2835 contains two types of SPI master controller; the
 113           "universal SPI master", and the regular SPI controller.
 114           This driver is for the universal/auxiliary SPI controller.
 115
 116 config SPI_BFIN5XX
 117         tristate "SPI controller driver for ADI Blackfin5xx"
 118         depends on BLACKFIN && !BF60x
 119         help
 120           This is the SPI controller master driver for Blackfin 5xx processor.
 121
 122 config SPI_ADI_V3
 123         tristate "SPI controller v3 for ADI"
 124         depends on BF60x
 125         help
 126           This is the SPI controller v3 master driver
 127           found on Blackfin 60x processor.
 128
 129 config SPI_BFIN_SPORT
 130         tristate "SPI bus via Blackfin SPORT"
 131         depends on BLACKFIN
 132         help
 133           Enable support for a SPI bus via the Blackfin SPORT peripheral.
 134
 135 config SPI_BCM53XX
 136         tristate "Broadcom BCM53xx SPI controller"
 137         depends on ARCH_BCM_5301X
 138         depends on BCMA_POSSIBLE
 139         select BCMA
 140         help
 141           Enable support for the SPI controller on Broadcom BCM53xx ARM SoCs.
 142
 143 config SPI_BCM63XX
 144         tristate "Broadcom BCM63xx SPI controller"
 145         depends on BCM63XX || COMPILE_TEST
 146         help
 147           Enable support for the SPI controller on the Broadcom BCM63xx SoCs.
 148
 149 config SPI_BCM63XX_HSSPI
 150         tristate "Broadcom BCM63XX HS SPI controller driver"
 151         depends on BCM63XX || COMPILE_TEST
 152         help
 153           This enables support for the High Speed SPI controller present on
 154           newer Broadcom BCM63XX SoCs.
 155
 156 config SPI_BITBANG
 157         tristate "Utilities for Bitbanging SPI masters"
 158         help
 159           With a few GPIO pins, your system can bitbang the SPI protocol.
 160           Select this to get SPI support through I/O pins (GPIO, parallel
 161           port, etc).  Or, some systems' SPI master controller drivers use
 162           this code to manage the per-word or per-transfer accesses to the
 163           hardware shift registers.
 164
 165           This is library code, and is automatically selected by drivers that
 166           need it.  You only need to select this explicitly to support driver
 167           modules that aren't part of this kernel tree.
 168
 169 config SPI_BUTTERFLY
 170         tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
 171         depends on PARPORT
 172         select SPI_BITBANG
 173         help
 174           This uses a custom parallel port cable to connect to an AVR
 175           Butterfly <http://www.atmel.com/products/avr/butterfly>, an
 176           inexpensive battery powered microcontroller evaluation board.
 177           This same cable can be used to flash new firmware.
 178
 179 config SPI_CADENCE
 180         tristate "Cadence SPI controller"
 181         help
 182           This selects the Cadence SPI controller master driver
 183           used by Xilinx Zynq and ZynqMP.
 184
 185 config SPI_CLPS711X
 186         tristate "CLPS711X host SPI controller"
 187         depends on ARCH_CLPS711X || COMPILE_TEST
 188         help
 189           This enables dedicated general purpose SPI/Microwire1-compatible
 190           master mode interface (SSI1) for CLPS711X-based CPUs.
 191
 192 config SPI_COLDFIRE_QSPI
 193         tristate "Freescale Coldfire QSPI controller"
 194         depends on (M520x || M523x || M5249 || M525x || M527x || M528x || M532x)
 195         help
 196           This enables support for the Coldfire QSPI controller in master
 197           mode.
 198
 199 config SPI_DAVINCI
 200         tristate "Texas Instruments DaVinci/DA8x/OMAP-L/AM1x SoC SPI controller"
 201         depends on ARCH_DAVINCI || ARCH_KEYSTONE
 202         select SPI_BITBANG
 203         help
 204           SPI master controller for DaVinci/DA8x/OMAP-L/AM1x SPI modules.
 205
 206 config SPI_DESIGNWARE
 207         tristate "DesignWare SPI controller core support"
 208         help
 209           general driver for SPI controller core from DesignWare
 210
 211 config SPI_DW_PCI
 212         tristate "PCI interface driver for DW SPI core"
 213         depends on SPI_DESIGNWARE && PCI
 214
 215 config SPI_DW_MID_DMA
 216         bool "DMA support for DW SPI controller on Intel MID platform"
 217         depends on SPI_DW_PCI && DW_DMAC_PCI
 218
 219 config SPI_DW_MMIO
 220         tristate "Memory-mapped io interface driver for DW SPI core"
 221         depends on SPI_DESIGNWARE
 222
 223 config SPI_DLN2
 224        tristate "Diolan DLN-2 USB SPI adapter"
 225        depends on MFD_DLN2
 226        help
 227          If you say yes to this option, support will be included for Diolan
 228          DLN2, a USB to SPI interface.
 229
 230          This driver can also be built as a module.  If so, the module
 231          will be called spi-dln2.
 232
 233 config SPI_EFM32
 234         tristate "EFM32 SPI controller"
 235         depends on OF && ARM && (ARCH_EFM32 || COMPILE_TEST)
 236         select SPI_BITBANG
 237         help
 238           Driver for the spi controller found on Energy Micro's EFM32 SoCs.
 239
 240 config SPI_EP93XX
 241         tristate "Cirrus Logic EP93xx SPI controller"
 242         depends on HAS_DMA
 243         depends on ARCH_EP93XX || COMPILE_TEST
 244         help
 245           This enables using the Cirrus EP93xx SPI controller in master
 246           mode.
 247
 248 config SPI_FALCON
 249         tristate "Falcon SPI controller support"
 250         depends on SOC_FALCON
 251         help
 252           The external bus unit (EBU) found on the FALC-ON SoC has SPI
 253           emulation that is designed for serial flash access. This driver
 254           has only been tested with m25p80 type chips. The hardware has no
 255           support for other types of SPI peripherals.
 256
 257 config SPI_GPIO
 258         tristate "GPIO-based bitbanging SPI Master"
 259         depends on GPIOLIB || COMPILE_TEST
 260         select SPI_BITBANG
 261         help
 262           This simple GPIO bitbanging SPI master uses the arch-neutral GPIO
 263           interface to manage MOSI, MISO, SCK, and chipselect signals.  SPI
 264           slaves connected to a bus using this driver are configured as usual,
 265           except that the spi_board_info.controller_data holds the GPIO number
 266           for the chipselect used by this controller driver.
 267
 268           Note that this driver often won't achieve even 1 Mbit/sec speeds,
 269           making it unusually slow for SPI.  If your platform can inline
 270           GPIO operations, you should be able to leverage that for better
 271           speed with a custom version of this driver; see the source code.
 272
 273 config SPI_IMG_SPFI
 274         tristate "IMG SPFI controller"
 275         depends on MIPS || COMPILE_TEST
 276         help
 277           This enables support for the SPFI master controller found on
 278           IMG SoCs.
 279
 280 config SPI_IMX
 281         tristate "Freescale i.MX SPI controllers"
 282         depends on ARCH_MXC || COMPILE_TEST
 283         select SPI_BITBANG
 284         help
 285           This enables using the Freescale i.MX SPI controllers in master
 286           mode.
 287
 288 config SPI_LM70_LLP
 289         tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
 290         depends on PARPORT
 291         select SPI_BITBANG
 292         help
 293           This driver supports the NS LM70 LLP Evaluation Board,
 294           which interfaces to an LM70 temperature sensor using
 295           a parallel port.
 296
 297 config SPI_LP8841_RTC
 298         tristate "ICP DAS LP-8841 SPI Controller for RTC"
 299         depends on MACH_PXA27X_DT || COMPILE_TEST
 300         help
 301           This driver provides an SPI master device to drive Maxim
 302           DS-1302 real time clock.
 303
 304           Say N here unless you plan to run the kernel on an ICP DAS
 305           LP-8x4x industrial computer.
 306
 307 config SPI_MPC52xx
 308         tristate "Freescale MPC52xx SPI (non-PSC) controller support"
 309         depends on PPC_MPC52xx
 310         help
 311           This drivers supports the MPC52xx SPI controller in master SPI
 312           mode.
 313
 314 config SPI_MPC52xx_PSC
 315         tristate "Freescale MPC52xx PSC SPI controller"
 316         depends on PPC_MPC52xx
 317         help
 318           This enables using the Freescale MPC52xx Programmable Serial
 319           Controller in master SPI mode.
 320
 321 config SPI_MPC512x_PSC
 322         tristate "Freescale MPC512x PSC SPI controller"
 323         depends on PPC_MPC512x
 324         help
 325           This enables using the Freescale MPC5121 Programmable Serial
 326           Controller in SPI master mode.
 327
 328 config SPI_FSL_LIB
 329         tristate
 330         depends on OF
 331
 332 config SPI_FSL_CPM
 333         tristate
 334         depends on FSL_SOC
 335
 336 config SPI_FSL_SPI
 337         tristate "Freescale SPI controller and Aeroflex Gaisler GRLIB SPI controller"
 338         depends on OF
 339         select SPI_FSL_LIB
 340         select SPI_FSL_CPM if FSL_SOC
 341         help
 342           This enables using the Freescale SPI controllers in master mode.
 343           MPC83xx platform uses the controller in cpu mode or CPM/QE mode.
 344           MPC8569 uses the controller in QE mode, MPC8610 in cpu mode.
 345           This also enables using the Aeroflex Gaisler GRLIB SPI controller in
 346           master mode.
 347
 348 config SPI_FSL_DSPI
 349         tristate "Freescale DSPI controller"
 350         select REGMAP_MMIO
 351         depends on SOC_VF610 || SOC_LS1021A || ARCH_LAYERSCAPE || COMPILE_TEST
 352         help
 353           This enables support for the Freescale DSPI controller in master
 354           mode. VF610 platform uses the controller.
 355
 356 config SPI_FSL_ESPI
 357         tristate "Freescale eSPI controller"
 358         depends on FSL_SOC
 359         select SPI_FSL_LIB
 360         help
 361           This enables using the Freescale eSPI controllers in master mode.
 362           From MPC8536, 85xx platform uses the controller, and all P10xx,
 363           P20xx, P30xx,P40xx, P50xx uses this controller.
 364
 365 config SPI_MESON_SPIFC
 366         tristate "Amlogic Meson SPIFC controller"
 367         depends on ARCH_MESON || COMPILE_TEST
 368         select REGMAP_MMIO
 369         help
 370           This enables master mode support for the SPIFC (SPI flash
 371           controller) available in Amlogic Meson SoCs.
 372
 373 config SPI_MT65XX
 374         tristate "MediaTek SPI controller"
 375         depends on ARCH_MEDIATEK || COMPILE_TEST
 376         help
 377           This selects the MediaTek(R) SPI bus driver.
 378           If you want to use MediaTek(R) SPI interface,
 379           say Y or M here.If you are not sure, say N.
 380           SPI drivers for Mediatek MT65XX and MT81XX series ARM SoCs.
 381
 382 config SPI_NUC900
 383         tristate "Nuvoton NUC900 series SPI"
 384         depends on ARCH_W90X900
 385         select SPI_BITBANG
 386         help
 387           SPI driver for Nuvoton NUC900 series ARM SoCs
 388
 389 config SPI_OC_TINY
 390         tristate "OpenCores tiny SPI"
 391         depends on GPIOLIB || COMPILE_TEST
 392         select SPI_BITBANG
 393         help
 394           This is the driver for OpenCores tiny SPI master controller.
 395
 396 config SPI_OCTEON
 397         tristate "Cavium OCTEON SPI controller"
 398         depends on CAVIUM_OCTEON_SOC
 399         help
 400           SPI host driver for the hardware found on some Cavium OCTEON
 401           SOCs.
 402
 403 config SPI_OMAP_UWIRE
 404         tristate "OMAP1 MicroWire"
 405         depends on ARCH_OMAP1
 406         select SPI_BITBANG
 407         help
 408           This hooks up to the MicroWire controller on OMAP1 chips.
 409
 410 config SPI_OMAP24XX
 411         tristate "McSPI driver for OMAP"
 412         depends on HAS_DMA
 413         depends on ARCH_OMAP2PLUS || COMPILE_TEST
 414         help
 415           SPI master controller for OMAP24XX and later Multichannel SPI
 416           (McSPI) modules.
 417
 418 config SPI_TI_QSPI
 419         tristate "DRA7xxx QSPI controller support"
 420         depends on ARCH_OMAP2PLUS || COMPILE_TEST
 421         help
 422           QSPI master controller for DRA7xxx used for flash devices.
 423           This device supports single, dual and quad read support, while
 424           it only supports single write mode.
 425
 426 config SPI_OMAP_100K
 427         tristate "OMAP SPI 100K"
 428         depends on ARCH_OMAP850 || ARCH_OMAP730 || COMPILE_TEST
 429         help
 430           OMAP SPI 100K master controller for omap7xx boards.
 431
 432 config SPI_ORION
 433         tristate "Orion SPI master"
 434         depends on PLAT_ORION || COMPILE_TEST
 435         help
 436           This enables using the SPI master controller on the Orion chips.
 437
 438 config SPI_PL022
 439         tristate "ARM AMBA PL022 SSP controller"
 440         depends on ARM_AMBA
 441         default y if MACH_U300
 442         default y if ARCH_REALVIEW
 443         default y if INTEGRATOR_IMPD1
 444         default y if ARCH_VERSATILE
 445         help
 446           This selects the ARM(R) AMBA(R) PrimeCell PL022 SSP
 447           controller. If you have an embedded system with an AMBA(R)
 448           bus and a PL022 controller, say Y or M here.
 449
 450 config SPI_PPC4xx
 451         tristate "PPC4xx SPI Controller"
 452         depends on PPC32 && 4xx
 453         select SPI_BITBANG
 454         help
 455           This selects a driver for the PPC4xx SPI Controller.
 456
 457 config SPI_PXA2XX
 458         tristate "PXA2xx SSP SPI master"
 459         depends on (ARCH_PXA || PCI || ACPI)
 460         select PXA_SSP if ARCH_PXA
 461         help
 462           This enables using a PXA2xx or Sodaville SSP port as a SPI master
 463           controller. The driver can be configured to use any SSP port and
 464           additional documentation can be found a Documentation/spi/pxa2xx.
 465
 466 config SPI_PXA2XX_PCI
 467         def_tristate SPI_PXA2XX && PCI && COMMON_CLK
 468
 469 config SPI_ROCKCHIP
 470         tristate "Rockchip SPI controller driver"
 471         help
 472           This selects a driver for Rockchip SPI controller.
 473
 474           If you say yes to this option, support will be included for
 475           RK3066, RK3188 and RK3288 families of SPI controller.
 476           Rockchip SPI controller support DMA transport and PIO mode.
 477           The main usecase of this controller is to use spi flash as boot
 478           device.
 479
 480 config SPI_RB4XX
 481         tristate "Mikrotik RB4XX SPI master"
 482         depends on SPI_MASTER && ATH79
 483         help
 484           SPI controller driver for the Mikrotik RB4xx series boards.
 485
 486 config SPI_RSPI
 487         tristate "Renesas RSPI/QSPI controller"
 488         depends on SUPERH || ARCH_RENESAS || COMPILE_TEST
 489         help
 490           SPI driver for Renesas RSPI and QSPI blocks.
 491
 492 config SPI_QUP
 493         tristate "Qualcomm SPI controller with QUP interface"
 494         depends on ARCH_QCOM || (ARM && COMPILE_TEST)
 495         help
 496           Qualcomm Universal Peripheral (QUP) core is an AHB slave that
 497           provides a common data path (an output FIFO and an input FIFO)
 498           for serial peripheral interface (SPI) mini-core. SPI in master
 499           mode supports up to 50MHz, up to four chip selects, programmable
 500           data path from 4 bits to 32 bits and numerous protocol variants.
 501
 502           This driver can also be built as a module.  If so, the module
 503           will be called spi_qup.
 504
 505 config SPI_S3C24XX
 506         tristate "Samsung S3C24XX series SPI"
 507         depends on ARCH_S3C24XX
 508         select SPI_BITBANG
 509         help
 510           SPI driver for Samsung S3C24XX series ARM SoCs
 511
 512 config SPI_S3C24XX_FIQ
 513         bool "S3C24XX driver with FIQ pseudo-DMA"
 514         depends on SPI_S3C24XX
 515         select FIQ
 516         help
 517           Enable FIQ support for the S3C24XX SPI driver to provide pseudo
 518           DMA by using the fast-interrupt request framework, This allows
 519           the driver to get DMA-like performance when there are either
 520           no free DMA channels, or when doing transfers that required both
 521           TX and RX data paths.
 522
 523 config SPI_S3C64XX
 524         tristate "Samsung S3C64XX series type SPI"
 525         depends on (PLAT_SAMSUNG || ARCH_EXYNOS)
 526         help
 527           SPI driver for Samsung S3C64XX and newer SoCs.
 528
 529 config SPI_SC18IS602
 530         tristate "NXP SC18IS602/602B/603 I2C to SPI bridge"
 531         depends on I2C
 532         help
 533           SPI driver for NXP SC18IS602/602B/603 I2C to SPI bridge.
 534
 535 config SPI_SH_MSIOF
 536         tristate "SuperH MSIOF SPI controller"
 537         depends on HAVE_CLK && HAS_DMA
 538         depends on SUPERH || ARCH_RENESAS || COMPILE_TEST
 539         help
 540           SPI driver for SuperH and SH Mobile MSIOF blocks.
 541
 542 config SPI_SH
 543         tristate "SuperH SPI controller"
 544         depends on SUPERH || COMPILE_TEST
 545         help
 546           SPI driver for SuperH SPI blocks.
 547
 548 config SPI_SH_SCI
 549         tristate "SuperH SCI SPI controller"
 550         depends on SUPERH
 551         select SPI_BITBANG
 552         help
 553           SPI driver for SuperH SCI blocks.
 554
 555 config SPI_SH_HSPI
 556         tristate "SuperH HSPI controller"
 557         depends on ARCH_RENESAS || COMPILE_TEST
 558         help
 559           SPI driver for SuperH HSPI blocks.
 560
 561 config SPI_SIRF
 562         tristate "CSR SiRFprimaII SPI controller"
 563         depends on SIRF_DMA
 564         select SPI_BITBANG
 565         help
 566           SPI driver for CSR SiRFprimaII SoCs
 567
 568 config SPI_ST_SSC4
 569         tristate "STMicroelectronics SPI SSC-based driver"
 570         depends on ARCH_STI
 571         help
 572           STMicroelectronics SoCs support for SPI. If you say yes to
 573           this option, support will be included for the SSC driven SPI.
 574
 575 config SPI_SUN4I
 576         tristate "Allwinner A10 SoCs SPI controller"
 577         depends on ARCH_SUNXI || COMPILE_TEST
 578         help
 579           SPI driver for Allwinner sun4i, sun5i and sun7i SoCs
 580
 581 config SPI_SUN6I
 582         tristate "Allwinner A31 SPI controller"
 583         depends on ARCH_SUNXI || COMPILE_TEST
 584         depends on RESET_CONTROLLER
 585         help
 586           This enables using the SPI controller on the Allwinner A31 SoCs.
 587
 588 config SPI_MXS
 589         tristate "Freescale MXS SPI controller"
 590         depends on ARCH_MXS
 591         select STMP_DEVICE
 592         help
 593           SPI driver for Freescale MXS devices.
 594
 595 config SPI_TEGRA114
 596         tristate "NVIDIA Tegra114 SPI Controller"
 597         depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
 598         depends on RESET_CONTROLLER && HAS_DMA
 599         help
 600           SPI driver for NVIDIA Tegra114 SPI Controller interface. This controller
 601           is different than the older SoCs SPI controller and also register interface
 602           get changed with this controller.
 603
 604 config SPI_TEGRA20_SFLASH
 605         tristate "Nvidia Tegra20 Serial flash Controller"
 606         depends on ARCH_TEGRA || COMPILE_TEST
 607         depends on RESET_CONTROLLER
 608         help
 609           SPI driver for Nvidia Tegra20 Serial flash Controller interface.
 610           The main usecase of this controller is to use spi flash as boot
 611           device.
 612
 613 config SPI_TEGRA20_SLINK
 614         tristate "Nvidia Tegra20/Tegra30 SLINK Controller"
 615         depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
 616         depends on RESET_CONTROLLER && HAS_DMA
 617         help
 618           SPI driver for Nvidia Tegra20/Tegra30 SLINK Controller interface.
 619
 620 config SPI_TOPCLIFF_PCH
 621         tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) SPI"
 622         depends on PCI && (X86_32 || MIPS || COMPILE_TEST)
 623         help
 624           SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus
 625           used in some x86 embedded processors.
 626
 627           This driver also supports the ML7213/ML7223/ML7831, a companion chip
 628           for the Atom E6xx series and compatible with the Intel EG20T PCH.
 629
 630 config SPI_TXX9
 631         tristate "Toshiba TXx9 SPI controller"
 632         depends on GPIOLIB && (CPU_TX49XX || COMPILE_TEST)
 633         help
 634           SPI driver for Toshiba TXx9 MIPS SoCs
 635
 636 config SPI_XCOMM
 637         tristate "Analog Devices AD-FMCOMMS1-EBZ SPI-I2C-bridge driver"
 638         depends on I2C
 639         help
 640           Support for the SPI-I2C bridge found on the Analog Devices
 641           AD-FMCOMMS1-EBZ board.
 642
 643 config SPI_XILINX
 644         tristate "Xilinx SPI controller common module"
 645         depends on HAS_IOMEM
 646         select SPI_BITBANG
 647         help
 648           This exposes the SPI controller IP from the Xilinx EDK.
 649
 650           See the "OPB Serial Peripheral Interface (SPI) (v1.00e)"
 651           Product Specification document (DS464) for hardware details.
 652
 653           Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)"
 654
 655 config SPI_XLP
 656         tristate "Netlogic XLP SPI controller driver"
 657         depends on CPU_XLP || COMPILE_TEST
 658         help
 659           Enable support for the SPI controller on the Netlogic XLP SoCs.
 660           Currently supported XLP variants are XLP8XX, XLP3XX, XLP2XX, XLP9XX
 661           and XLP5XX.
 662
 663           If you have a Netlogic XLP platform say Y here.
 664           If unsure, say N.
 665
 666 config SPI_XTENSA_XTFPGA
 667         tristate "Xtensa SPI controller for xtfpga"
 668         depends on (XTENSA && XTENSA_PLATFORM_XTFPGA) || COMPILE_TEST
 669         select SPI_BITBANG
 670         help
 671           SPI driver for xtfpga SPI master controller.
 672
 673           This simple SPI master controller is built into xtfpga bitstreams
 674           and is used to control daughterboard audio codec. It always transfers
 675           16 bit words in SPI mode 0, automatically asserting CS on transfer
 676           start and deasserting on end.
 677
 678 config SPI_ZYNQMP_GQSPI
 679         tristate "Xilinx ZynqMP GQSPI controller"
 680         depends on SPI_MASTER && HAS_DMA
 681         help
 682           Enables Xilinx GQSPI controller driver for Zynq UltraScale+ MPSoC.
 683
 684 #
 685 # Add new SPI master controllers in alphabetical order above this line
 686 #
 687
 688 #
 689 # There are lots of SPI device types, with sensors and memory
 690 # being probably the most widely used ones.
 691 #
 692 comment "SPI Protocol Masters"
 693
 694 config SPI_SPIDEV
 695         tristate "User mode SPI device driver support"
 696         help
 697           This supports user mode SPI protocol drivers.
 698
 699           Note that this application programming interface is EXPERIMENTAL
 700           and hence SUBJECT TO CHANGE WITHOUT NOTICE while it stabilizes.
 701
 702 config SPI_LOOPBACK_TEST
 703         tristate "spi loopback test framework support"
 704         depends on m
 705         help
 706           This enables the SPI loopback testing framework driver
 707
 708           primarily used for development of spi_master drivers
 709           and to detect regressions
 710
 711 config SPI_TLE62X0
 712         tristate "Infineon TLE62X0 (for power switching)"
 713         depends on SYSFS
 714         help
 715           SPI driver for Infineon TLE62X0 series line driver chips,
 716           such as the TLE6220, TLE6230 and TLE6240.  This provides a
 717           sysfs interface, with each line presented as a kind of GPIO
 718           exposing both switch control and diagnostic feedback.
 719
 720 #
 721 # Add new SPI protocol masters in alphabetical order above this line
 722 #
 723
 724 endif # SPI_MASTER
 725
 726 # (slave support would go here)
 727
 728 endif # SPI