drivers/spi/spi-xilinx.c

   1 /*
   2  * Xilinx SPI controller driver (master mode only)
   3  *
   4  * Author: MontaVista Software, Inc.
   5  *      source@mvista.com
   6  *
   7  * Copyright (c) 2010 Secret Lab Technologies, Ltd.
   8  * Copyright (c) 2009 Intel Corporation
   9  * 2002-2007 (c) MontaVista Software, Inc.
  10
  11  * This program is free software; you can redistribute it and/or modify
  12  * it under the terms of the GNU General Public License version 2 as
  13  * published by the Free Software Foundation.
  14  */
  15
  16 #include <linux/module.h>
  17 #include <linux/interrupt.h>
  18 #include <linux/of.h>
  19 #include <linux/platform_device.h>
  20 #include <linux/spi/spi.h>
  21 #include <linux/spi/spi_bitbang.h>
  22 #include <linux/spi/xilinx_spi.h>
  23 #include <linux/io.h>
  24
  25 #define XILINX_SPI_MAX_CS       32
  26
  27 #define XILINX_SPI_NAME "xilinx_spi"
  28
  29 /* Register definitions as per "OPB Serial Peripheral Interface (SPI) (v1.00e)
  30  * Product Specification", DS464
  31  */
  32 #define XSPI_CR_OFFSET          0x60    /* Control Register */
  33
  34 #define XSPI_CR_LOOP            0x01
  35 #define XSPI_CR_ENABLE          0x02
  36 #define XSPI_CR_MASTER_MODE     0x04
  37 #define XSPI_CR_CPOL            0x08
  38 #define XSPI_CR_CPHA            0x10
  39 #define XSPI_CR_MODE_MASK       (XSPI_CR_CPHA | XSPI_CR_CPOL | \
  40                                  XSPI_CR_LSB_FIRST | XSPI_CR_LOOP)
  41 #define XSPI_CR_TXFIFO_RESET    0x20
  42 #define XSPI_CR_RXFIFO_RESET    0x40
  43 #define XSPI_CR_MANUAL_SSELECT  0x80
  44 #define XSPI_CR_TRANS_INHIBIT   0x100
  45 #define XSPI_CR_LSB_FIRST       0x200
  46
  47 #define XSPI_SR_OFFSET          0x64    /* Status Register */
  48
  49 #define XSPI_SR_RX_EMPTY_MASK   0x01    /* Receive FIFO is empty */
  50 #define XSPI_SR_RX_FULL_MASK    0x02    /* Receive FIFO is full */
  51 #define XSPI_SR_TX_EMPTY_MASK   0x04    /* Transmit FIFO is empty */
  52 #define XSPI_SR_TX_FULL_MASK    0x08    /* Transmit FIFO is full */
  53 #define XSPI_SR_MODE_FAULT_MASK 0x10    /* Mode fault error */
  54
  55 #define XSPI_TXD_OFFSET         0x68    /* Data Transmit Register */
  56 #define XSPI_RXD_OFFSET         0x6c    /* Data Receive Register */
  57
  58 #define XSPI_SSR_OFFSET         0x70    /* 32-bit Slave Select Register */
  59
  60 /* Register definitions as per "OPB IPIF (v3.01c) Product Specification", DS414
  61  * IPIF registers are 32 bit
  62  */
  63 #define XIPIF_V123B_DGIER_OFFSET        0x1c    /* IPIF global int enable reg */
  64 #define XIPIF_V123B_GINTR_ENABLE        0x80000000
  65
  66 #define XIPIF_V123B_IISR_OFFSET         0x20    /* IPIF interrupt status reg */
  67 #define XIPIF_V123B_IIER_OFFSET         0x28    /* IPIF interrupt enable reg */
  68
  69 #define XSPI_INTR_MODE_FAULT            0x01    /* Mode fault error */
  70 #define XSPI_INTR_SLAVE_MODE_FAULT      0x02    /* Selected as slave while
  71                                                  * disabled */
  72 #define XSPI_INTR_TX_EMPTY              0x04    /* TxFIFO is empty */
  73 #define XSPI_INTR_TX_UNDERRUN           0x08    /* TxFIFO was underrun */
  74 #define XSPI_INTR_RX_FULL               0x10    /* RxFIFO is full */
  75 #define XSPI_INTR_RX_OVERRUN            0x20    /* RxFIFO was overrun */
  76 #define XSPI_INTR_TX_HALF_EMPTY         0x40    /* TxFIFO is half empty */
  77
  78 #define XIPIF_V123B_RESETR_OFFSET       0x40    /* IPIF reset register */
  79 #define XIPIF_V123B_RESET_MASK          0x0a    /* the value to write */
  80
  81 struct xilinx_spi {
  82         /* bitbang has to be first */
  83         struct spi_bitbang bitbang;
  84         struct completion done;
  85         void __iomem    *regs;  /* virt. address of the control registers */
  86
  87         int             irq;
  88
  89         u8 *rx_ptr;             /* pointer in the Tx buffer */
  90         const u8 *tx_ptr;       /* pointer in the Rx buffer */
  91         u8 bytes_per_word;
  92         int buffer_size;        /* buffer size in words */
  93         u32 cs_inactive;        /* Level of the CS pins when inactive*/
  94         unsigned int (*read_fn)(void __iomem *);
  95         void (*write_fn)(u32, void __iomem *);
  96 };
  97
  98 static void xspi_write32(u32 val, void __iomem *addr)
  99 {
 100         iowrite32(val, addr);
 101 }
 102
 103 static unsigned int xspi_read32(void __iomem *addr)
 104 {
 105         return ioread32(addr);
 106 }
 107
 108 static void xspi_write32_be(u32 val, void __iomem *addr)
 109 {
 110         iowrite32be(val, addr);
 111 }
 112
 113 static unsigned int xspi_read32_be(void __iomem *addr)
 114 {
 115         return ioread32be(addr);
 116 }
 117
 118 static void xilinx_spi_tx(struct xilinx_spi *xspi)
 119 {
 120         u32 data = 0;
 121
 122         if (!xspi->tx_ptr) {
 123                 xspi->write_fn(0, xspi->regs + XSPI_TXD_OFFSET);
 124                 return;
 125         }
 126
 127         switch (xspi->bytes_per_word) {
 128         case 1:
 129                 data = *(u8 *)(xspi->tx_ptr);
 130                 break;
 131         case 2:
 132                 data = *(u16 *)(xspi->tx_ptr);
 133                 break;
 134         case 4:
 135                 data = *(u32 *)(xspi->tx_ptr);
 136                 break;
 137         }
 138
 139         xspi->write_fn(data, xspi->regs + XSPI_TXD_OFFSET);
 140         xspi->tx_ptr += xspi->bytes_per_word;
 141 }
 142
 143 static void xilinx_spi_rx(struct xilinx_spi *xspi)
 144 {
 145         u32 data = xspi->read_fn(xspi->regs + XSPI_RXD_OFFSET);
 146
 147         if (!xspi->rx_ptr)
 148                 return;
 149
 150         switch (xspi->bytes_per_word) {
 151         case 1:
 152                 *(u8 *)(xspi->rx_ptr) = data;
 153                 break;
 154         case 2:
 155                 *(u16 *)(xspi->rx_ptr) = data;
 156                 break;
 157         case 4:
 158                 *(u32 *)(xspi->rx_ptr) = data;
 159                 break;
 160         }
 161
 162         xspi->rx_ptr += xspi->bytes_per_word;
 163 }
 164
 165 static void xspi_init_hw(struct xilinx_spi *xspi)
 166 {
 167         void __iomem *regs_base = xspi->regs;
 168
 169         /* Reset the SPI device */
 170         xspi->write_fn(XIPIF_V123B_RESET_MASK,
 171                 regs_base + XIPIF_V123B_RESETR_OFFSET);
 172         /* Enable the transmit empty interrupt, which we use to determine
 173          * progress on the transmission.
 174          */
 175         xspi->write_fn(XSPI_INTR_TX_EMPTY,
 176                         regs_base + XIPIF_V123B_IIER_OFFSET);
 177         /* Disable the global IPIF interrupt */
 178         xspi->write_fn(0, regs_base + XIPIF_V123B_DGIER_OFFSET);
 179         /* Deselect the slave on the SPI bus */
 180         xspi->write_fn(0xffff, regs_base + XSPI_SSR_OFFSET);
 181         /* Disable the transmitter, enable Manual Slave Select Assertion,
 182          * put SPI controller into master mode, and enable it */
 183         xspi->write_fn(XSPI_CR_MANUAL_SSELECT | XSPI_CR_MASTER_MODE |
 184                 XSPI_CR_ENABLE | XSPI_CR_TXFIFO_RESET | XSPI_CR_RXFIFO_RESET,
 185                 regs_base + XSPI_CR_OFFSET);
 186 }
 187
 188 static void xilinx_spi_chipselect(struct spi_device *spi, int is_on)
 189 {
 190         struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
 191         u16 cr;
 192         u32 cs;
 193
 194         if (is_on == BITBANG_CS_INACTIVE) {
 195                 /* Deselect the slave on the SPI bus */
 196                 xspi->write_fn(xspi->cs_inactive, xspi->regs + XSPI_SSR_OFFSET);
 197                 return;
 198         }
 199
 200         /* Set the SPI clock phase and polarity */
 201         cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET) & ~XSPI_CR_MODE_MASK;
 202         if (spi->mode & SPI_CPHA)
 203                 cr |= XSPI_CR_CPHA;
 204         if (spi->mode & SPI_CPOL)
 205                 cr |= XSPI_CR_CPOL;
 206         if (spi->mode & SPI_LSB_FIRST)
 207                 cr |= XSPI_CR_LSB_FIRST;
 208         if (spi->mode & SPI_LOOP)
 209                 cr |= XSPI_CR_LOOP;
 210         xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
 211
 212         /* We do not check spi->max_speed_hz here as the SPI clock
 213          * frequency is not software programmable (the IP block design
 214          * parameter)
 215          */
 216
 217         cs = xspi->cs_inactive;
 218         cs ^= BIT(spi->chip_select);
 219
 220         /* Activate the chip select */
 221         xspi->write_fn(cs, xspi->regs + XSPI_SSR_OFFSET);
 222 }
 223
 224 /* spi_bitbang requires custom setup_transfer() to be defined if there is a
 225  * custom txrx_bufs().
 226  */
 227 static int xilinx_spi_setup_transfer(struct spi_device *spi,
 228                 struct spi_transfer *t)
 229 {
 230         struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
 231
 232         if (spi->mode & SPI_CS_HIGH)
 233                 xspi->cs_inactive &= ~BIT(spi->chip_select);
 234         else
 235                 xspi->cs_inactive |= BIT(spi->chip_select);
 236
 237         return 0;
 238 }
 239
 240 static int xilinx_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
 241 {
 242         struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
 243         int remaining_words;    /* the number of words left to transfer */
 244         bool use_irq = false;
 245         u16 cr = 0;
 246
 247         /* We get here with transmitter inhibited */
 248
 249         xspi->tx_ptr = t->tx_buf;
 250         xspi->rx_ptr = t->rx_buf;
 251         remaining_words = t->len / xspi->bytes_per_word;
 252
 253         if (xspi->irq >= 0 &&  remaining_words > xspi->buffer_size) {
 254                 u32 isr;
 255                 use_irq = true;
 256                 /* Inhibit irq to avoid spurious irqs on tx_empty*/
 257                 cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET);
 258                 xspi->write_fn(cr | XSPI_CR_TRANS_INHIBIT,
 259                                xspi->regs + XSPI_CR_OFFSET);
 260                 /* ACK old irqs (if any) */
 261                 isr = xspi->read_fn(xspi->regs + XIPIF_V123B_IISR_OFFSET);
 262                 if (isr)
 263                         xspi->write_fn(isr,
 264                                        xspi->regs + XIPIF_V123B_IISR_OFFSET);
 265                 /* Enable the global IPIF interrupt */
 266                 xspi->write_fn(XIPIF_V123B_GINTR_ENABLE,
 267                                 xspi->regs + XIPIF_V123B_DGIER_OFFSET);
 268                 reinit_completion(&xspi->done);
 269         }
 270
 271         while (remaining_words) {
 272                 int n_words, tx_words, rx_words;
 273                 u32 sr;
 274
 275                 n_words = min(remaining_words, xspi->buffer_size);
 276
 277                 tx_words = n_words;
 278                 while (tx_words--)
 279                         xilinx_spi_tx(xspi);
 280
 281                 /* Start the transfer by not inhibiting the transmitter any
 282                  * longer
 283                  */
 284
 285                 if (use_irq) {
 286                         xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
 287                         wait_for_completion(&xspi->done);
 288                         /* A transmit has just completed. Process received data
 289                          * and check for more data to transmit. Always inhibit
 290                          * the transmitter while the Isr refills the transmit
 291                          * register/FIFO, or make sure it is stopped if we're
 292                          * done.
 293                          */
 294                         xspi->write_fn(cr | XSPI_CR_TRANS_INHIBIT,
 295                                        xspi->regs + XSPI_CR_OFFSET);
 296                         sr = XSPI_SR_TX_EMPTY_MASK;
 297                 } else
 298                         sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
 299
 300                 /* Read out all the data from the Rx FIFO */
 301                 rx_words = n_words;
 302                 while (rx_words) {
 303                         if ((sr & XSPI_SR_TX_EMPTY_MASK) && (rx_words > 1)) {
 304                                 xilinx_spi_rx(xspi);
 305                                 rx_words--;
 306                                 continue;
 307                         }
 308
 309                         sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
 310                         if (!(sr & XSPI_SR_RX_EMPTY_MASK)) {
 311                                 xilinx_spi_rx(xspi);
 312                                 rx_words--;
 313                         }
 314                 }
 315
 316                 remaining_words -= n_words;
 317         }
 318
 319         if (use_irq) {
 320                 xspi->write_fn(0, xspi->regs + XIPIF_V123B_DGIER_OFFSET);
 321                 xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
 322         }
 323
 324         return t->len;
 325 }
 326
 327
 328 /* This driver supports single master mode only. Hence Tx FIFO Empty
 329  * is the only interrupt we care about.
 330  * Receive FIFO Overrun, Transmit FIFO Underrun, Mode Fault, and Slave Mode
 331  * Fault are not to happen.
 332  */
 333 static irqreturn_t xilinx_spi_irq(int irq, void *dev_id)
 334 {
 335         struct xilinx_spi *xspi = dev_id;
 336         u32 ipif_isr;
 337
 338         /* Get the IPIF interrupts, and clear them immediately */
 339         ipif_isr = xspi->read_fn(xspi->regs + XIPIF_V123B_IISR_OFFSET);
 340         xspi->write_fn(ipif_isr, xspi->regs + XIPIF_V123B_IISR_OFFSET);
 341
 342         if (ipif_isr & XSPI_INTR_TX_EMPTY) {    /* Transmission completed */
 343                 complete(&xspi->done);
 344         }
 345
 346         return IRQ_HANDLED;
 347 }
 348
 349 static int xilinx_spi_find_buffer_size(struct xilinx_spi *xspi)
 350 {
 351         u8 sr;
 352         int n_words = 0;
 353
 354         /*
 355          * Before the buffer_size detection we reset the core
 356          * to make sure we start with a clean state.
 357          */
 358         xspi->write_fn(XIPIF_V123B_RESET_MASK,
 359                 xspi->regs + XIPIF_V123B_RESETR_OFFSET);
 360
 361         /* Fill the Tx FIFO with as many words as possible */
 362         do {
 363                 xspi->write_fn(0, xspi->regs + XSPI_TXD_OFFSET);
 364                 sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
 365                 n_words++;
 366         } while (!(sr & XSPI_SR_TX_FULL_MASK));
 367
 368         return n_words;
 369 }
 370
 371 static const struct of_device_id xilinx_spi_of_match[] = {
 372         { .compatible = "xlnx,xps-spi-2.00.a", },
 373         { .compatible = "xlnx,xps-spi-2.00.b", },
 374         {}
 375 };
 376 MODULE_DEVICE_TABLE(of, xilinx_spi_of_match);
 377
 378 static int xilinx_spi_probe(struct platform_device *pdev)
 379 {
 380         struct xilinx_spi *xspi;
 381         struct xspi_platform_data *pdata;
 382         struct resource *res;
 383         int ret, num_cs = 0, bits_per_word = 8;
 384         struct spi_master *master;
 385         u32 tmp;
 386         u8 i;
 387
 388         pdata = dev_get_platdata(&pdev->dev);
 389         if (pdata) {
 390                 num_cs = pdata->num_chipselect;
 391                 bits_per_word = pdata->bits_per_word;
 392         } else {
 393                 of_property_read_u32(pdev->dev.of_node, "xlnx,num-ss-bits",
 394                                           &num_cs);
 395         }
 396
 397         if (!num_cs) {
 398                 dev_err(&pdev->dev,
 399                         "Missing slave select configuration data\n");
 400                 return -EINVAL;
 401         }
 402
 403         if (num_cs > XILINX_SPI_MAX_CS) {
 404                 dev_err(&pdev->dev, "Invalid number of spi slaves\n");
 405                 return -EINVAL;
 406         }
 407
 408         master = spi_alloc_master(&pdev->dev, sizeof(struct xilinx_spi));
 409         if (!master)
 410                 return -ENODEV;
 411
 412         /* the spi->mode bits understood by this driver: */
 413         master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_LSB_FIRST | SPI_LOOP |
 414                             SPI_CS_HIGH;
 415
 416         xspi = spi_master_get_devdata(master);
 417         xspi->cs_inactive = 0xffffffff;
 418         xspi->bitbang.master = master;
 419         xspi->bitbang.chipselect = xilinx_spi_chipselect;
 420         xspi->bitbang.setup_transfer = xilinx_spi_setup_transfer;
 421         xspi->bitbang.txrx_bufs = xilinx_spi_txrx_bufs;
 422         init_completion(&xspi->done);
 423
 424         res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 425         xspi->regs = devm_ioremap_resource(&pdev->dev, res);
 426         if (IS_ERR(xspi->regs)) {
 427                 ret = PTR_ERR(xspi->regs);
 428                 goto put_master;
 429         }
 430
 431         master->bus_num = pdev->id;
 432         master->num_chipselect = num_cs;
 433         master->dev.of_node = pdev->dev.of_node;
 434
 435         /*
 436          * Detect endianess on the IP via loop bit in CR. Detection
 437          * must be done before reset is sent because incorrect reset
 438          * value generates error interrupt.
 439          * Setup little endian helper functions first and try to use them
 440          * and check if bit was correctly setup or not.
 441          */
 442         xspi->read_fn = xspi_read32;
 443         xspi->write_fn = xspi_write32;
 444
 445         xspi->write_fn(XSPI_CR_LOOP, xspi->regs + XSPI_CR_OFFSET);
 446         tmp = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET);
 447         tmp &= XSPI_CR_LOOP;
 448         if (tmp != XSPI_CR_LOOP) {
 449                 xspi->read_fn = xspi_read32_be;
 450                 xspi->write_fn = xspi_write32_be;
 451         }
 452
 453         master->bits_per_word_mask = SPI_BPW_MASK(bits_per_word);
 454         xspi->bytes_per_word = bits_per_word / 8;
 455         xspi->buffer_size = xilinx_spi_find_buffer_size(xspi);
 456
 457         xspi->irq = platform_get_irq(pdev, 0);
 458         if (xspi->irq >= 0) {
 459                 /* Register for SPI Interrupt */
 460                 ret = devm_request_irq(&pdev->dev, xspi->irq, xilinx_spi_irq, 0,
 461                                 dev_name(&pdev->dev), xspi);
 462                 if (ret)
 463                         goto put_master;
 464         }
 465
 466         /* SPI controller initializations */
 467         xspi_init_hw(xspi);
 468
 469         ret = spi_bitbang_start(&xspi->bitbang);
 470         if (ret) {
 471                 dev_err(&pdev->dev, "spi_bitbang_start FAILED\n");
 472                 goto put_master;
 473         }
 474
 475         dev_info(&pdev->dev, "at 0x%08llX mapped to 0x%p, irq=%d\n",
 476                 (unsigned long long)res->start, xspi->regs, xspi->irq);
 477
 478         if (pdata) {
 479                 for (i = 0; i < pdata->num_devices; i++)
 480                         spi_new_device(master, pdata->devices + i);
 481         }
 482
 483         platform_set_drvdata(pdev, master);
 484         return 0;
 485
 486 put_master:
 487         spi_master_put(master);
 488
 489         return ret;
 490 }
 491
 492 static int xilinx_spi_remove(struct platform_device *pdev)
 493 {
 494         struct spi_master *master = platform_get_drvdata(pdev);
 495         struct xilinx_spi *xspi = spi_master_get_devdata(master);
 496         void __iomem *regs_base = xspi->regs;
 497
 498         spi_bitbang_stop(&xspi->bitbang);
 499
 500         /* Disable all the interrupts just in case */
 501         xspi->write_fn(0, regs_base + XIPIF_V123B_IIER_OFFSET);
 502         /* Disable the global IPIF interrupt */
 503         xspi->write_fn(0, regs_base + XIPIF_V123B_DGIER_OFFSET);
 504
 505         spi_master_put(xspi->bitbang.master);
 506
 507         return 0;
 508 }
 509
 510 /* work with hotplug and coldplug */
 511 MODULE_ALIAS("platform:" XILINX_SPI_NAME);
 512
 513 static struct platform_driver xilinx_spi_driver = {
 514         .probe = xilinx_spi_probe,
 515         .remove = xilinx_spi_remove,
 516         .driver = {
 517                 .name = XILINX_SPI_NAME,
 518                 .of_match_table = xilinx_spi_of_match,
 519         },
 520 };
 521 module_platform_driver(xilinx_spi_driver);
 522
 523 MODULE_AUTHOR("MontaVista Software, Inc. <source@mvista.com>");
 524 MODULE_DESCRIPTION("Xilinx SPI driver");
 525 MODULE_LICENSE("GPL");