+# Copyright (C) 2012-2018 Free Software Foundation, Inc.
+
+# This program is free software; you can redistribute it and/or modify
+# it under the terms of the GNU General Public License as published by
+# the Free Software Foundation; either version 3 of the License, or
+# (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street - Fifth Floor, Boston, MA 02110-1301, USA.
+
#
# These tests should be valid on all targets.
#
# This test is meaningless for the PA; the difference of two undefined
# symbols is something that is (and must be) supported on the PA.
+# The same is true for ALPHA-VMS.
#
-# The MN10300 port supports link time relaxation which in turn allows
-# for link time resolution of the differneces of two symbols which are
-# undefined at assembly time. Hence this test will not pass for the
-# MN10300. The same thing is true for the RX port as well.
-if { ![istarget hppa*-*-*]
- && ![istarget rx-*-*]
+# The AVR, MICROBLAZE, MN10300, RL78 and RX ports all support link time
+# relaxation, which in turn allows for link time resolution of the
+# differences of two previously undefined symbols. Hence this test will
+# not pass for these targets.
+if { ![istarget alpha*-*-*vms*]
+ && ![istarget am3*-*-*]
+ && ![istarget avr-*-*]
+ && ![istarget ft32-*-*]
+ && ![istarget hppa*-*-*]
+ && ![istarget microblaze-*-*]
&& ![istarget mn10300-*-*]
- && ![istarget am3*-*-*] } then {
+ && ![istarget msp430*-*-*]
+ && ![istarget riscv*-*-*]
+ && ![istarget rl78-*-*]
+ && ![istarget rx-*-*] } then {
gas_test_error "diff1.s" "" "difference of two undefined symbols"
}
gas_test_error "equiv1.s" "" ".equiv for symbol already set to another one"
gas_test_error "equiv2.s" "" ".equiv for symbol already set to an expression"
+gas_test_error "none.s" "-o $srcdir/$subdir/none.s" "Output file must be distinct from input"
+
# .equ works differently on some targets.
case $target_triplet in {
{ hppa*-*-* } { }
# .equ works differently on some targets.
# linkrelax-ing prevents most forward references from working.
case $target_triplet in {
+ { am3*-*-* } { }
{ *c54x*-*-* } { }
{ cr16*-*-* } { }
{ crx*-*-* } { }
{ h8300*-*-* } { }
{ hppa*-*-* } { }
{ mep-*-* } { }
+ { microblaze-*-* } { }
{ mn10\[23\]00*-*-* } { }
default {
# Some targets don't manage to resolve BFD_RELOC_8 for constants.
setup_xfail "alpha*-*-*" "*c30*-*-*" "*c4x*-*-*" \
- "d\[13\]0v*-*-*" "i860-*-*" "mips*-*-*" "msp430-*-*" \
- "pdp11-*-*" "sparc*-*-*" "xtensa*-*-*"
+ "d\[13\]0v*-*-*" \
+ "pdp11-*-*" "xtensa*-*-*"
run_dump_test forward
}
}
-# aout relocs are often weird, so is mep and mips-ecoff. don't bother testing
+# aout relocs are often weird, so is mep. don't bother testing
# som doesn't use a .text section
# mmix doesn't like .L1:
# ti addresses aren't octets.
{ hppa*64*-*-* } {
run_dump_test fwdexp
}
+ { alpha-*-*linux*ecoff } { }
+ { alpha-*-osf* } { }
{ hppa*-*-hpux* } { }
{ mep-*-* } { }
- { mips*-*-ecoff* } { }
{ mmix-*-* } { }
+ { nds32*-*-* } { }
{ tic30*-*-* } { }
{ tic4x*-*-* } { }
{ tic54x*-*-* } { }
# pdp11 gets unexpected reloc types.
case $target_triplet in {
{ alpha*-*-* } { }
+ { am3*-*-* } { }
{ cr16*-*-* } { }
{ crx*-*-* } { }
{ h8300-*-* } { }
{ mips*-*-* } { }
{ mn10200-*-* } { }
{ mn10300-*-* } { }
+ { msp430*-*-* } { }
+ { nds32*-*-* } { }
{ pdp11-*-* } { }
{ tic30*-*-* } { }
{ tic4x*-*-* } { }
{ z80-*-* } { }
default {
run_dump_test redef
- # The next two tests can fail if the target does not convert fixups
- # against ordinary symbols into relocations against section symbols.
- # This is usually revealed by the error message:
- # symbol `sym' required but not present
- setup_xfail "*arm*-*-*aout*" "*arm*-*-*coff" \
- "*arm*-*-pe" "m68hc*-*-*" \
- "rx-*-*" "vax*-*-*" "z8k-*-*"
+ # These targets fail redef2 because they disallow redefined
+ # symbols on relocs.
+ setup_xfail "m68hc1*-*-*" "m6811-*-*" "m6812-*-*" "rl78-*-*"
+ setup_xfail "riscv*-*-*" "rx-*-*" "vax*-*-*" "xgate*-*-*" "z8k-*-*"
run_dump_test redef2
- setup_xfail "*-*-aix*" "bfin-*-*" "hppa*-*-hpux*" \
- "i\[3-7\]86-*-*coff" "i\[3-7\]86-*-*pe" "i\[3-7\]86-*-go32*" \
+ setup_xfail "m68hc1*-*-*" "m6811-*-*" "m6812-*-*" "rl78-*-*"
+ setup_xfail "riscv*-*-*" "rx-*-*" "vax*-*-*" "xgate*-*-*" "z8k-*-*"
+ # rs6000-aix disallows redefinition via .comm.
+ setup_xfail "*-*-aix*"
+ # These targets fail redef3 because section contents for the
+ # word referencing the .comm sym is not zero and/or its reloc
+ # has a non-zero addend. Relaxing the test would hide real
+ # failures.
+ setup_xfail "bfin-*-*" "i\[3-7\]86-*-*coff" \
+ "i\[3-7\]86-*-*pe" "i\[3-7\]86-*-go32*" \
"i\[3-7\]86-*-cygwin*" "i\[3-7\]86-*-mingw*" \
- "x86_64-*-*coff" "x86_64-*-*pe" \
- "x86_64-*-cygwin*" "x86_64-*-mingw*" \
- "m68hc*-*-*" "or32-*-*" "rx-*-*" "vax*-*-*" "z8k-*-*"
+ "x86_64-*-cygwin*" "x86_64-*-mingw*"
run_dump_test redef3
gas_test_error "redef4.s" "" ".set for symbol already used as label"
gas_test_error "redef5.s" "" ".set for symbol already defined through .comm"
set x 0
gas_start "x930509.s" "-al"
while 1 {
-# We need to accomodate both byte orders here.
+# We need to accommodate both byte orders here.
# If ".long" means an 8-byte value on some target someday, this test will have
# to be fixed.
expect {
# C54x assembler (for compatibility) does not allow differences between
# forward references.
# C30 counts a four byte offset as a difference of one.
-if { ![istarget hppa*-*-*] &&
- ![istarget cr16*-*-*] &&
- ![istarget crx*-*-*] &&
- ![istarget *c30*-*-*] &&
- ![istarget *c4x*-*-*] &&
- ![istarget *c54x*-*-*] } then {
- # the vax fails because VMS can apparently actually handle this
+if { ![istarget *c30*-*-*]
+ && ![istarget *c4x*-*-*]
+ && ![istarget *c54x*-*-*]
+ && ![istarget cr16*-*-*]
+ && ![istarget crx*-*-*]
+ && ![istarget ft32-*-*]
+ && ![istarget h8300*-*-*]
+ && ![istarget hppa*-*-*] } then {
+ # The vax fails because VMS can apparently actually handle this
# case in relocs, so gas doesn't handle it itself.
- setup_xfail "h8300*-*-elf*" "mn10200*-*-*" "mn10300*-*-*" "vax*-*-vms*"
+ # msp430, mn10[23]00 and riscv emit two relocs to handle the difference of two symbols.
+ setup_xfail "am3*-*-*" "mn10200-*-*" "mn10300*-*-*" "msp430*-*-*" "riscv*-*-*" "vax*-*-vms*"
do_930509a
}
default {
run_dump_test struct
run_dump_test align
+ setup_xfail "ns32k-*-*"
run_dump_test align2
}
}
# character (it is allowed to be a line comment character).
if [string match "" [lindex [gas_run excl.s "-o /dev/null" ""] 0]] {
run_dump_test altmac2
- # Similarly this test does not work when ! is a line seperator.
+ # Similarly this test does not work when ! is a line separator.
run_dump_test eval
}
}
# We omit the ARM toolchains because they define locals to
# start with '.', which eliminates .eos, .text etc from the output.
# Omit c54x, since .tag and .def mean something different on that target
-if { ([istarget *-*-coff*] && ![istarget *arm*-*-coff] && ![istarget thumb*-*-coff] && ![istarget xscale-*-coff] && ![istarget *c4x*-*-coff] && ![istarget *c54x*-*-coff]) \
- ||([istarget *-*-pe*] && ![istarget arm*-*-pe*] && ![istarget thumb*-*-pe*]) \
+if { ([istarget *-*-coff*] && ![istarget arm*-*-coff] && ![istarget *c4x*-*-coff] && ![istarget *c54x*-*-coff]) \
+ ||([istarget *-*-pe*] && ![istarget arm*-*-pe*]) \
|| [istarget i*86-*-aix*] \
|| [istarget i*86-*-sco*] \
|| [istarget i*86-*-isc*] \
|| [istarget i*86-*-cygwin*] \
|| [istarget x86_64-*-mingw*] \
|| [istarget i*86-*-*nt] \
- || [istarget i*86-*-interix*] \
- || ([istarget i960-*-vxworks5.*] && ![istarget i960-*-vxworks5.0*]) } {
+ || [istarget i*86-*-interix*] } {
run_dump_test cofftag
}
# This test is not suitable for the PA for various reasons
# not limited to the fact that it depends on specific section
# names appearing in the output file.
-# again, p2align doesn't work on c54x target
+# Again, p2align doesn't work on c54x and related targets.
case $target_triplet in {
+ { alpha-*-linux*ecoff} { }
+ { alpha-*-osf*} { }
{ hppa*-*-* } { }
{ *c4x*-*-* } { }
{ *c54x*-*-* } { }
+ { rl78-*-* } { }
{ rx-*-* } { }
default {
test_cond
gas_test "fastcall.s" "" "" "fastcall labels"
}
-if { ![istarget "bfin-*-*"] } then {
+if { ![istarget "bfin-*-*"] && ![istarget "nds32*-*-*"] } then {
run_dump_test assign
}
run_dump_test sleb128
+run_dump_test sleb128-2
+run_dump_test sleb128-3
+run_dump_test sleb128-4
+run_dump_test sleb128-5
+# .byte is not 8 bits on either tic4x or tic54x
+if { ![istarget "tic4x*-*-*"] && ![istarget "tic54x*-*-*"] } {
+ run_dump_test sleb128-7
+ run_dump_test sleb128-8
+}
+run_dump_test sleb128-9
# .byte is 32 bits on tic4x, and .p2align isn't supported on tic54x
# .space is different on hppa*-hpux.
run_dump_test byte
}
-# .quad is 16 bytes on i960.
-if { ![istarget "i960-*-*"] } {
- run_dump_test quad
-}
-
-# som doesn't use .data section.
-case $target_triplet in {
- { hppa*64*-*-* } {
- run_dump_test octa
- }
- { hppa*-*-hpux* } { }
- default {
- run_dump_test octa
- }
-}
+run_dump_test quad
+run_dump_test octa
# .set works differently on some targets.
case $target_triplet in {
{ *c54x*-*-* } { }
{ z80-*-* } { }
default {
+ setup_xfail "nds32*-*-*"
run_dump_test weakref1
run_dump_test weakref1g
run_dump_test weakref1l
gas_test_error "weakref4.s" "" "is already defined"
run_dump_test string
+if [is_elf_format] {
+ run_dump_test none
+}
+
+run_dump_test quoted-sym-names
+
+run_list_test pr20312
load_lib gas-dg.exp
dg-init
dg-runtest [lsort [glob -nocomplain $srcdir/$subdir/err-*.s $srcdir/$subdir/warn-*.s]] "" ""
dg-finish
+
+# Set $nop_type appropriately to indicate the NOP instruction mnemonic.
+case $target_triplet in {
+ { "mmix-*-*" } {
+ set nop_type 5
+ }
+ { "or1k*-*-*" } {
+ set nop_type 2
+ }
+ { "ia64-*-*" } {
+ set nop_type 1
+ }
+ default {
+ set nop_type 0
+ }
+}
+run_dump_test "org-1" [list [list as "--defsym nop_type=$nop_type"]]
+run_dump_test "org-2"
+run_dump_test "org-3"
+run_dump_test "org-4"
+run_dump_test "org-5"
+run_dump_test "org-6"
+
+run_dump_test "fill-1"