SND_SOC_DAPM_SUPPLY("ADC Power", NAU8825_REG_ANALOG_ADC_2, 6, 0, NULL,
0),
- /* ADC for button press detection */
- SND_SOC_DAPM_ADC("SAR", NULL, NAU8825_REG_SAR_CTRL,
- NAU8825_SAR_ADC_EN_SFT, 0),
+ /* ADC for button press detection. A dapm supply widget is used to
+ * prevent dapm_power_widgets keeping the codec at SND_SOC_BIAS_ON
+ * during suspend.
+ */
+ SND_SOC_DAPM_SUPPLY("SAR", NAU8825_REG_SAR_CTRL,
+ NAU8825_SAR_ADC_EN_SFT, 0, NULL, 0),
SND_SOC_DAPM_PGA_S("ADACL", 2, NAU8825_REG_RDAC, 12, 0, NULL, 0),
SND_SOC_DAPM_PGA_S("ADACR", 2, NAU8825_REG_RDAC, 13, 0, NULL, 0),
static void nau8825_restart_jack_detection(struct regmap *regmap)
{
+ /* Chip needs one FSCLK cycle in order to generate interrupts,
+ * as we cannot guarantee one will be provided by the system. Turning
+ * master mode on then off enables us to generate that FSCLK cycle
+ * with a minimum of contention on the clock bus.
+ */
+ regmap_update_bits(regmap, NAU8825_REG_I2S_PCM_CTRL2,
+ NAU8825_I2S_MS_MASK, NAU8825_I2S_MS_MASTER);
+ regmap_update_bits(regmap, NAU8825_REG_I2S_PCM_CTRL2,
+ NAU8825_I2S_MS_MASK, NAU8825_I2S_MS_SLAVE);
+
/* this will restart the entire jack detection process including MIC/GND
* switching and create interrupts. We have to go from 0 to 1 and back
* to 0 to restart.
struct regmap *regmap = nau8825->regmap;
int active_irq, clear_irq = 0, event = 0, event_mask = 0;
- regmap_read(regmap, NAU8825_REG_IRQ_STATUS, &active_irq);
+ if (regmap_read(regmap, NAU8825_REG_IRQ_STATUS, &active_irq)) {
+ dev_err(nau8825->dev, "failed to read irq status\n");
+ return IRQ_NONE;
+ }
if ((active_irq & NAU8825_JACK_EJECTION_IRQ_MASK) ==
NAU8825_JACK_EJECTION_DETECTED) {
return ret;
}
}
-
- ret = regcache_sync(nau8825->regmap);
- if (ret) {
- dev_err(codec->dev,
- "Failed to sync cache: %d\n", ret);
- return ret;
- }
}
-
break;
case SND_SOC_BIAS_OFF:
if (nau8825->mclk_freq)
clk_disable_unprepare(nau8825->mclk);
-
- regcache_mark_dirty(nau8825->regmap);
break;
}
return 0;
}
+#ifdef CONFIG_PM
+static int nau8825_suspend(struct snd_soc_codec *codec)
+{
+ struct nau8825 *nau8825 = snd_soc_codec_get_drvdata(codec);
+
+ disable_irq(nau8825->irq);
+ regcache_cache_only(nau8825->regmap, true);
+ regcache_mark_dirty(nau8825->regmap);
+
+ return 0;
+}
+
+static int nau8825_resume(struct snd_soc_codec *codec)
+{
+ struct nau8825 *nau8825 = snd_soc_codec_get_drvdata(codec);
+
+ /* The chip may lose power and reset in S3. regcache_sync restores
+ * register values including configurations for sysclk, irq, and
+ * jack/button detection.
+ */
+ regcache_cache_only(nau8825->regmap, false);
+ regcache_sync(nau8825->regmap);
+
+ /* Check the jack plug status directly. If the headset is unplugged
+ * during S3 when the chip has no power, there will be no jack
+ * detection irq even after the nau8825_restart_jack_detection below,
+ * because the chip just thinks no headset has ever been plugged in.
+ */
+ if (!nau8825_is_jack_inserted(nau8825->regmap)) {
+ nau8825_eject_jack(nau8825);
+ snd_soc_jack_report(nau8825->jack, 0, SND_JACK_HEADSET);
+ }
+
+ enable_irq(nau8825->irq);
+
+ /* Run jack detection to check the type (OMTP or CTIA) of the headset
+ * if there is one. This handles the case where a different type of
+ * headset is plugged in during S3. This triggers an IRQ iff a headset
+ * is already plugged in.
+ */
+ nau8825_restart_jack_detection(nau8825->regmap);
+
+ return 0;
+}
+#else
+#define nau8825_suspend NULL
+#define nau8825_resume NULL
+#endif
+
static struct snd_soc_codec_driver nau8825_codec_driver = {
.probe = nau8825_codec_probe,
.set_sysclk = nau8825_set_sysclk,
.set_pll = nau8825_set_pll,
.set_bias_level = nau8825_set_bias_level,
.suspend_bias_off = true,
+ .suspend = nau8825_suspend,
+ .resume = nau8825_resume,
.controls = nau8825_controls,
.num_controls = ARRAY_SIZE(nau8825_controls),
regmap_update_bits(regmap, NAU8825_REG_ENA_CTRL,
NAU8825_ENABLE_DACR, NAU8825_ENABLE_DACR);
- /* Chip needs one FSCLK cycle in order to generate interrupts,
- * as we cannot guarantee one will be provided by the system. Turning
- * master mode on then off enables us to generate that FSCLK cycle
- * with a minimum of contention on the clock bus.
- */
- regmap_update_bits(regmap, NAU8825_REG_I2S_PCM_CTRL2,
- NAU8825_I2S_MS_MASK, NAU8825_I2S_MS_MASTER);
- regmap_update_bits(regmap, NAU8825_REG_I2S_PCM_CTRL2,
- NAU8825_I2S_MS_MASK, NAU8825_I2S_MS_SLAVE);
-
ret = devm_request_threaded_irq(nau8825->dev, nau8825->irq, NULL,
nau8825_interrupt, IRQF_TRIGGER_LOW | IRQF_ONESHOT,
"nau8825", nau8825);
return 0;
}
-#ifdef CONFIG_PM_SLEEP
-static int nau8825_suspend(struct device *dev)
-{
- struct i2c_client *client = to_i2c_client(dev);
- struct nau8825 *nau8825 = dev_get_drvdata(dev);
-
- disable_irq(client->irq);
- regcache_cache_only(nau8825->regmap, true);
- regcache_mark_dirty(nau8825->regmap);
-
- return 0;
-}
-
-static int nau8825_resume(struct device *dev)
-{
- struct i2c_client *client = to_i2c_client(dev);
- struct nau8825 *nau8825 = dev_get_drvdata(dev);
-
- regcache_cache_only(nau8825->regmap, false);
- regcache_sync(nau8825->regmap);
- enable_irq(client->irq);
-
- return 0;
-}
-#endif
-
-static const struct dev_pm_ops nau8825_pm = {
- SET_SYSTEM_SLEEP_PM_OPS(nau8825_suspend, nau8825_resume)
-};
-
static const struct i2c_device_id nau8825_i2c_ids[] = {
{ "nau8825", 0 },
{ }
.name = "nau8825",
.of_match_table = of_match_ptr(nau8825_of_ids),
.acpi_match_table = ACPI_PTR(nau8825_acpi_match),
- .pm = &nau8825_pm,
},
.probe = nau8825_i2c_probe,
.remove = nau8825_i2c_remove,
projects / deliverable / linux.git / blobdiff