Commit | Line | Data |
---|---|---|
3c1c2fce DH |
1 | What: /sys/bus/hid/drivers/wiimote/<dev>/led1 |
2 | What: /sys/bus/hid/drivers/wiimote/<dev>/led2 | |
3 | What: /sys/bus/hid/drivers/wiimote/<dev>/led3 | |
4 | What: /sys/bus/hid/drivers/wiimote/<dev>/led4 | |
5 | Date: July 2011 | |
6 | KernelVersion: 3.1 | |
7 | Contact: David Herrmann <dh.herrmann@googlemail.com> | |
8 | Description: Make it possible to set/get current led state. Reading from it | |
9 | returns 0 if led is off and 1 if it is on. Writing 0 to it | |
10 | disables the led, writing 1 enables it. | |
c1e51398 DH |
11 | |
12 | What: /sys/bus/hid/drivers/wiimote/<dev>/extension | |
13 | Date: August 2011 | |
14 | KernelVersion: 3.2 | |
c7da0867 | 15 | Contact: David Herrmann <dh.herrmann@gmail.com> |
c1e51398 DH |
16 | Description: This file contains the currently connected and initialized |
17 | extensions. It can be one of: none, motionp, nunchuck, classic, | |
18 | motionp+nunchuck, motionp+classic | |
19 | motionp is the official Nintendo Motion+ extension, nunchuck is | |
20 | the official Nintendo Nunchuck extension and classic is the | |
21 | Nintendo Classic Controller extension. The motionp extension can | |
22 | be combined with the other two. | |
c7da0867 DH |
23 | Starting with kernel-version 3.11 Motion Plus hotplugging is |
24 | supported and if detected, it's no longer reported as static | |
25 | extension. You will get uevent notifications for the motion-plus | |
26 | device then. | |
27 | ||
28 | What: /sys/bus/hid/drivers/wiimote/<dev>/devtype | |
29 | Date: May 2013 | |
30 | KernelVersion: 3.11 | |
31 | Contact: David Herrmann <dh.herrmann@gmail.com> | |
32 | Description: While a device is initialized by the wiimote driver, we perform | |
33 | a device detection and signal a "change" uevent after it is | |
34 | done. This file shows the detected device type. "pending" means | |
35 | that the detection is still ongoing, "unknown" means, that the | |
36 | device couldn't be detected or loaded. "generic" means, that the | |
37 | device couldn't be detected but supports basic Wii Remote | |
38 | features and can be used. | |
39 | Other strings for each device-type are available and may be | |
40 | added if new device-specific detections are added. | |
41 | Currently supported are: | |
42 | gen10: First Wii Remote generation | |
43 | gen20: Second Wii Remote Plus generation (builtin MP) | |
44 | balanceboard: Wii Balance Board | |
8b1fded7 DH |
45 | |
46 | What: /sys/bus/hid/drivers/wiimote/<dev>/bboard_calib | |
47 | Date: May 2013 | |
48 | KernelVersion: 3.11 | |
49 | Contact: David Herrmann <dh.herrmann@gmail.com> | |
50 | Description: This attribute is only provided if the device was detected as a | |
51 | balance board. It provides a single line with 3 calibration | |
52 | values for all 4 sensors. The values are separated by colons and | |
53 | are each 2 bytes long (encoded as 4 digit hexadecimal value). | |
54 | First, 0kg values for all 4 sensors are written, followed by the | |
55 | 17kg values for all 4 sensors and last the 34kg values for all 4 | |
56 | sensors. | |
57 | Calibration data is already applied by the kernel to all input | |
58 | values but may be used by user-space to perform other | |
59 | transformations. | |
08072dde DH |
60 | |
61 | What: /sys/bus/hid/drivers/wiimote/<dev>/pro_calib | |
62 | Date: October 2013 | |
63 | KernelVersion: 3.13 | |
64 | Contact: David Herrmann <dh.herrmann@gmail.com> | |
65 | Description: This attribute is only provided if the device was detected as a | |
66 | pro-controller. It provides a single line with 4 calibration | |
67 | values for all 4 analog sticks. Format is: "x1:y1 x2:y2". Data | |
68 | is prefixed with a +/-. Each value is a signed 16bit number. | |
69 | Data is encoded as decimal numbers and specifies the offsets of | |
70 | the analog sticks of the pro-controller. | |
71 | Calibration data is already applied by the kernel to all input | |
72 | values but may be used by user-space to perform other | |
73 | transformations. | |
74 | Calibration data is detected by the kernel during device setup. | |
75 | You can write "scan\n" into this file to re-trigger calibration. | |
76 | You can also write data directly in the form "x1:y1 x2:y2" to | |
77 | set the calibration values manually. |