Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | |
2 | ||
3 | Command Line Options for Linux/m68k | |
4 | =================================== | |
5 | ||
6 | Last Update: 2 May 1999 | |
7 | Linux/m68k version: 2.2.6 | |
8 | Author: Roman.Hodek@informatik.uni-erlangen.de (Roman Hodek) | |
9 | Update: jds@kom.auc.dk (Jes Sorensen) and faq@linux-m68k.org (Chris Lawrence) | |
10 | ||
11 | 0) Introduction | |
12 | =============== | |
13 | ||
14 | Often I've been asked which command line options the Linux/m68k | |
15 | kernel understands, or how the exact syntax for the ... option is, or | |
16 | ... about the option ... . I hope, this document supplies all the | |
17 | answers... | |
18 | ||
19 | Note that some options might be outdated, their descriptions being | |
20 | incomplete or missing. Please update the information and send in the | |
21 | patches. | |
22 | ||
23 | ||
24 | 1) Overview of the Kernel's Option Processing | |
25 | ============================================= | |
26 | ||
27 | The kernel knows three kinds of options on its command line: | |
28 | ||
29 | 1) kernel options | |
30 | 2) environment settings | |
31 | 3) arguments for init | |
32 | ||
33 | To which of these classes an argument belongs is determined as | |
34 | follows: If the option is known to the kernel itself, i.e. if the name | |
35 | (the part before the '=') or, in some cases, the whole argument string | |
36 | is known to the kernel, it belongs to class 1. Otherwise, if the | |
37 | argument contains an '=', it is of class 2, and the definition is put | |
38 | into init's environment. All other arguments are passed to init as | |
39 | command line options. | |
40 | ||
41 | This document describes the valid kernel options for Linux/m68k in | |
42 | the version mentioned at the start of this file. Later revisions may | |
43 | add new such options, and some may be missing in older versions. | |
44 | ||
45 | In general, the value (the part after the '=') of an option is a | |
46 | list of values separated by commas. The interpretation of these values | |
47 | is up to the driver that "owns" the option. This association of | |
48 | options with drivers is also the reason that some are further | |
49 | subdivided. | |
50 | ||
51 | ||
52 | 2) General Kernel Options | |
53 | ========================= | |
54 | ||
55 | 2.1) root= | |
56 | ---------- | |
57 | ||
58 | Syntax: root=/dev/<device> | |
59 | or: root=<hex_number> | |
60 | ||
61 | This tells the kernel which device it should mount as the root | |
62 | filesystem. The device must be a block device with a valid filesystem | |
63 | on it. | |
64 | ||
65 | The first syntax gives the device by name. These names are converted | |
66 | into a major/minor number internally in the kernel in an unusual way. | |
67 | Normally, this "conversion" is done by the device files in /dev, but | |
68 | this isn't possible here, because the root filesystem (with /dev) | |
69 | isn't mounted yet... So the kernel parses the name itself, with some | |
70 | hardcoded name to number mappings. The name must always be a | |
71 | combination of two or three letters, followed by a decimal number. | |
72 | Valid names are: | |
73 | ||
74 | /dev/ram: -> 0x0100 (initial ramdisk) | |
75 | /dev/hda: -> 0x0300 (first IDE disk) | |
76 | /dev/hdb: -> 0x0340 (second IDE disk) | |
77 | /dev/sda: -> 0x0800 (first SCSI disk) | |
78 | /dev/sdb: -> 0x0810 (second SCSI disk) | |
79 | /dev/sdc: -> 0x0820 (third SCSI disk) | |
80 | /dev/sdd: -> 0x0830 (forth SCSI disk) | |
81 | /dev/sde: -> 0x0840 (fifth SCSI disk) | |
82 | /dev/fd : -> 0x0200 (floppy disk) | |
83 | /dev/xda: -> 0x0c00 (first XT disk, unused in Linux/m68k) | |
84 | /dev/xdb: -> 0x0c40 (second XT disk, unused in Linux/m68k) | |
85 | /dev/ada: -> 0x1c00 (first ACSI device) | |
86 | /dev/adb: -> 0x1c10 (second ACSI device) | |
87 | /dev/adc: -> 0x1c20 (third ACSI device) | |
88 | /dev/add: -> 0x1c30 (forth ACSI device) | |
89 | ||
90 | The last four names are available only if the kernel has been compiled | |
91 | with Atari and ACSI support. | |
92 | ||
93 | The name must be followed by a decimal number, that stands for the | |
94 | partition number. Internally, the value of the number is just | |
95 | added to the device number mentioned in the table above. The | |
96 | exceptions are /dev/ram and /dev/fd, where /dev/ram refers to an | |
97 | initial ramdisk loaded by your bootstrap program (please consult the | |
98 | instructions for your bootstrap program to find out how to load an | |
99 | initial ramdisk). As of kernel version 2.0.18 you must specify | |
100 | /dev/ram as the root device if you want to boot from an initial | |
101 | ramdisk. For the floppy devices, /dev/fd, the number stands for the | |
102 | floppy drive number (there are no partitions on floppy disks). I.e., | |
103 | /dev/fd0 stands for the first drive, /dev/fd1 for the second, and so | |
104 | on. Since the number is just added, you can also force the disk format | |
105 | by adding a number greater than 3. If you look into your /dev | |
106 | directory, use can see the /dev/fd0D720 has major 2 and minor 16. You | |
107 | can specify this device for the root FS by writing "root=/dev/fd16" on | |
108 | the kernel command line. | |
109 | ||
110 | [Strange and maybe uninteresting stuff ON] | |
111 | ||
112 | This unusual translation of device names has some strange | |
113 | consequences: If, for example, you have a symbolic link from /dev/fd | |
114 | to /dev/fd0D720 as an abbreviation for floppy driver #0 in DD format, | |
115 | you cannot use this name for specifying the root device, because the | |
116 | kernel cannot see this symlink before mounting the root FS and it | |
117 | isn't in the table above. If you use it, the root device will not be | |
118 | set at all, without an error message. Another example: You cannot use a | |
119 | partition on e.g. the sixth SCSI disk as the root filesystem, if you | |
120 | want to specify it by name. This is, because only the devices up to | |
121 | /dev/sde are in the table above, but not /dev/sdf. Although, you can | |
122 | use the sixth SCSI disk for the root FS, but you have to specify the | |
123 | device by number... (see below). Or, even more strange, you can use the | |
124 | fact that there is no range checking of the partition number, and your | |
125 | knowledge that each disk uses 16 minors, and write "root=/dev/sde17" | |
126 | (for /dev/sdf1). | |
127 | ||
128 | [Strange and maybe uninteresting stuff OFF] | |
129 | ||
130 | If the device containing your root partition isn't in the table | |
131 | above, you can also specify it by major and minor numbers. These are | |
132 | written in hex, with no prefix and no separator between. E.g., if you | |
133 | have a CD with contents appropriate as a root filesystem in the first | |
134 | SCSI CD-ROM drive, you boot from it by "root=0b00". Here, hex "0b" = | |
135 | decimal 11 is the major of SCSI CD-ROMs, and the minor 0 stands for | |
136 | the first of these. You can find out all valid major numbers by | |
137 | looking into include/linux/major.h. | |
138 | ||
139 | ||
140 | 2.2) ro, rw | |
141 | ----------- | |
142 | ||
143 | Syntax: ro | |
144 | or: rw | |
145 | ||
146 | These two options tell the kernel whether it should mount the root | |
147 | filesystem read-only or read-write. The default is read-only, except | |
148 | for ramdisks, which default to read-write. | |
149 | ||
150 | ||
151 | 2.3) debug | |
152 | ---------- | |
153 | ||
154 | Syntax: debug | |
155 | ||
156 | This raises the kernel log level to 10 (the default is 7). This is the | |
157 | same level as set by the "dmesg" command, just that the maximum level | |
158 | selectable by dmesg is 8. | |
159 | ||
160 | ||
161 | 2.4) debug= | |
162 | ----------- | |
163 | ||
164 | Syntax: debug=<device> | |
165 | ||
166 | This option causes certain kernel messages be printed to the selected | |
167 | debugging device. This can aid debugging the kernel, since the | |
168 | messages can be captured and analyzed on some other machine. Which | |
169 | devices are possible depends on the machine type. There are no checks | |
170 | for the validity of the device name. If the device isn't implemented, | |
171 | nothing happens. | |
172 | ||
173 | Messages logged this way are in general stack dumps after kernel | |
174 | memory faults or bad kernel traps, and kernel panics. To be exact: all | |
175 | messages of level 0 (panic messages) and all messages printed while | |
176 | the log level is 8 or more (their level doesn't matter). Before stack | |
177 | dumps, the kernel sets the log level to 10 automatically. A level of | |
178 | at least 8 can also be set by the "debug" command line option (see | |
179 | 2.3) and at run time with "dmesg -n 8". | |
180 | ||
181 | Devices possible for Amiga: | |
182 | ||
183 | - "ser": built-in serial port; parameters: 9600bps, 8N1 | |
184 | - "mem": Save the messages to a reserved area in chip mem. After | |
185 | rebooting, they can be read under AmigaOS with the tool | |
186 | 'dmesg'. | |
187 | ||
188 | Devices possible for Atari: | |
189 | ||
190 | - "ser1": ST-MFP serial port ("Modem1"); parameters: 9600bps, 8N1 | |
191 | - "ser2": SCC channel B serial port ("Modem2"); parameters: 9600bps, 8N1 | |
192 | - "ser" : default serial port | |
193 | This is "ser2" for a Falcon, and "ser1" for any other machine | |
194 | - "midi": The MIDI port; parameters: 31250bps, 8N1 | |
195 | - "par" : parallel port | |
196 | The printing routine for this implements a timeout for the | |
197 | case there's no printer connected (else the kernel would | |
198 | lock up). The timeout is not exact, but usually a few | |
199 | seconds. | |
200 | ||
201 | ||
202 | 2.6) ramdisk= | |
203 | ------------- | |
204 | ||
205 | Syntax: ramdisk=<size> | |
206 | ||
207 | This option instructs the kernel to set up a ramdisk of the given | |
208 | size in KBytes. Do not use this option if the ramdisk contents are | |
209 | passed by bootstrap! In this case, the size is selected automatically | |
210 | and should not be overwritten. | |
211 | ||
212 | The only application is for root filesystems on floppy disks, that | |
213 | should be loaded into memory. To do that, select the corresponding | |
214 | size of the disk as ramdisk size, and set the root device to the disk | |
215 | drive (with "root="). | |
216 | ||
217 | ||
218 | 2.7) swap= | |
219 | 2.8) buff= | |
220 | ----------- | |
221 | ||
222 | I can't find any sign of these options in 2.2.6. | |
223 | ||
224 | ||
225 | 3) General Device Options (Amiga and Atari) | |
226 | =========================================== | |
227 | ||
228 | 3.1) ether= | |
229 | ----------- | |
230 | ||
231 | Syntax: ether=[<irq>[,<base_addr>[,<mem_start>[,<mem_end>]]]],<dev-name> | |
232 | ||
233 | <dev-name> is the name of a net driver, as specified in | |
234 | drivers/net/Space.c in the Linux source. Most prominent are eth0, ... | |
235 | eth3, sl0, ... sl3, ppp0, ..., ppp3, dummy, and lo. | |
236 | ||
237 | The non-ethernet drivers (sl, ppp, dummy, lo) obviously ignore the | |
238 | settings by this options. Also, the existing ethernet drivers for | |
239 | Linux/m68k (ariadne, a2065, hydra) don't use them because Zorro boards | |
240 | are really Plug-'n-Play, so the "ether=" option is useless altogether | |
241 | for Linux/m68k. | |
242 | ||
243 | ||
244 | 3.2) hd= | |
245 | -------- | |
246 | ||
247 | Syntax: hd=<cylinders>,<heads>,<sectors> | |
248 | ||
249 | This option sets the disk geometry of an IDE disk. The first hd= | |
250 | option is for the first IDE disk, the second for the second one. | |
251 | (I.e., you can give this option twice.) In most cases, you won't have | |
252 | to use this option, since the kernel can obtain the geometry data | |
253 | itself. It exists just for the case that this fails for one of your | |
254 | disks. | |
255 | ||
256 | ||
257 | 3.3) max_scsi_luns= | |
258 | ------------------- | |
259 | ||
260 | Syntax: max_scsi_luns=<n> | |
261 | ||
262 | Sets the maximum number of LUNs (logical units) of SCSI devices to | |
263 | be scanned. Valid values for <n> are between 1 and 8. Default is 8 if | |
264 | "Probe all LUNs on each SCSI device" was selected during the kernel | |
265 | configuration, else 1. | |
266 | ||
267 | ||
268 | 3.4) st= | |
269 | -------- | |
270 | ||
271 | Syntax: st=<buffer_size>,[<write_thres>,[<max_buffers>]] | |
272 | ||
273 | Sets several parameters of the SCSI tape driver. <buffer_size> is | |
274 | the number of 512-byte buffers reserved for tape operations for each | |
275 | device. <write_thres> sets the number of blocks which must be filled | |
276 | to start an actual write operation to the tape. Maximum value is the | |
277 | total number of buffers. <max_buffer> limits the total number of | |
278 | buffers allocated for all tape devices. | |
279 | ||
280 | ||
281 | 3.5) dmasound= | |
282 | -------------- | |
283 | ||
284 | Syntax: dmasound=[<buffers>,<buffer-size>[,<catch-radius>]] | |
285 | ||
286 | This option controls some configurations of the Linux/m68k DMA sound | |
287 | driver (Amiga and Atari): <buffers> is the number of buffers you want | |
288 | to use (minimum 4, default 4), <buffer-size> is the size of each | |
289 | buffer in kilobytes (minimum 4, default 32) and <catch-radius> says | |
290 | how much percent of error will be tolerated when setting a frequency | |
291 | (maximum 10, default 0). For example with 3% you can play 8000Hz | |
292 | AU-Files on the Falcon with its hardware frequency of 8195Hz and thus | |
293 | don't need to expand the sound. | |
294 | ||
295 | ||
296 | ||
297 | 4) Options for Atari Only | |
298 | ========================= | |
299 | ||
300 | 4.1) video= | |
301 | ----------- | |
302 | ||
303 | Syntax: video=<fbname>:<sub-options...> | |
304 | ||
305 | The <fbname> parameter specifies the name of the frame buffer, | |
306 | eg. most atari users will want to specify `atafb' here. The | |
307 | <sub-options> is a comma-separated list of the sub-options listed | |
308 | below. | |
309 | ||
310 | NB: Please notice that this option was renamed from `atavideo' to | |
311 | `video' during the development of the 1.3.x kernels, thus you | |
312 | might need to update your boot-scripts if upgrading to 2.x from | |
313 | an 1.2.x kernel. | |
314 | ||
315 | NBB: The behavior of video= was changed in 2.1.57 so the recommended | |
316 | option is to specify the name of the frame buffer. | |
317 | ||
318 | 4.1.1) Video Mode | |
319 | ----------------- | |
320 | ||
321 | This sub-option may be any of the predefined video modes, as listed | |
322 | in atari/atafb.c in the Linux/m68k source tree. The kernel will | |
323 | activate the given video mode at boot time and make it the default | |
324 | mode, if the hardware allows. Currently defined names are: | |
325 | ||
326 | - stlow : 320x200x4 | |
327 | - stmid, default5 : 640x200x2 | |
328 | - sthigh, default4: 640x400x1 | |
329 | - ttlow : 320x480x8, TT only | |
330 | - ttmid, default1 : 640x480x4, TT only | |
331 | - tthigh, default2: 1280x960x1, TT only | |
332 | - vga2 : 640x480x1, Falcon only | |
333 | - vga4 : 640x480x2, Falcon only | |
334 | - vga16, default3 : 640x480x4, Falcon only | |
335 | - vga256 : 640x480x8, Falcon only | |
336 | - falh2 : 896x608x1, Falcon only | |
337 | - falh16 : 896x608x4, Falcon only | |
338 | ||
339 | If no video mode is given on the command line, the kernel tries the | |
340 | modes names "default<n>" in turn, until one is possible with the | |
341 | hardware in use. | |
342 | ||
343 | A video mode setting doesn't make sense, if the external driver is | |
344 | activated by a "external:" sub-option. | |
345 | ||
346 | 4.1.2) inverse | |
347 | -------------- | |
348 | ||
349 | Invert the display. This affects both, text (consoles) and graphics | |
350 | (X) display. Usually, the background is chosen to be black. With this | |
351 | option, you can make the background white. | |
352 | ||
353 | 4.1.3) font | |
354 | ----------- | |
355 | ||
356 | Syntax: font:<fontname> | |
357 | ||
358 | Specify the font to use in text modes. Currently you can choose only | |
359 | between `VGA8x8', `VGA8x16' and `PEARL8x8'. `VGA8x8' is default, if the | |
360 | vertical size of the display is less than 400 pixel rows. Otherwise, the | |
361 | `VGA8x16' font is the default. | |
362 | ||
363 | 4.1.4) hwscroll_ | |
364 | ---------------- | |
365 | ||
366 | Syntax: hwscroll_<n> | |
367 | ||
368 | The number of additional lines of video memory to reserve for | |
369 | speeding up the scrolling ("hardware scrolling"). Hardware scrolling | |
370 | is possible only if the kernel can set the video base address in steps | |
371 | fine enough. This is true for STE, MegaSTE, TT, and Falcon. It is not | |
372 | possible with plain STs and graphics cards (The former because the | |
373 | base address must be on a 256 byte boundary there, the latter because | |
374 | the kernel doesn't know how to set the base address at all.) | |
375 | ||
376 | By default, <n> is set to the number of visible text lines on the | |
377 | display. Thus, the amount of video memory is doubled, compared to no | |
378 | hardware scrolling. You can turn off the hardware scrolling altogether | |
379 | by setting <n> to 0. | |
380 | ||
381 | 4.1.5) internal: | |
382 | ---------------- | |
383 | ||
384 | Syntax: internal:<xres>;<yres>[;<xres_max>;<yres_max>;<offset>] | |
385 | ||
386 | This option specifies the capabilities of some extended internal video | |
387 | hardware, like e.g. OverScan. <xres> and <yres> give the (extended) | |
388 | dimensions of the screen. | |
389 | ||
390 | If your OverScan needs a black border, you have to write the last | |
391 | three arguments of the "internal:". <xres_max> is the maximum line | |
392 | length the hardware allows, <yres_max> the maximum number of lines. | |
393 | <offset> is the offset of the visible part of the screen memory to its | |
394 | physical start, in bytes. | |
395 | ||
396 | Often, extended interval video hardware has to be activated somehow. | |
397 | For this, see the "sw_*" options below. | |
398 | ||
399 | 4.1.6) external: | |
400 | ---------------- | |
401 | ||
402 | Syntax: | |
403 | external:<xres>;<yres>;<depth>;<org>;<scrmem>[;<scrlen>[;<vgabase>\ | |
404 | [;<colw>[;<coltype>[;<xres_virtual>]]]]] | |
405 | ||
406 | [I had to break this line...] | |
407 | ||
408 | This is probably the most complicated parameter... It specifies that | |
409 | you have some external video hardware (a graphics board), and how to | |
410 | use it under Linux/m68k. The kernel cannot know more about the hardware | |
411 | than you tell it here! The kernel also is unable to set or change any | |
412 | video modes, since it doesn't know about any board internal. So, you | |
413 | have to switch to that video mode before you start Linux, and cannot | |
414 | switch to another mode once Linux has started. | |
415 | ||
416 | The first 3 parameters of this sub-option should be obvious: <xres>, | |
417 | <yres> and <depth> give the dimensions of the screen and the number of | |
670e9f34 | 418 | planes (depth). The depth is the logarithm to base 2 of the number |
1da177e4 LT |
419 | of colors possible. (Or, the other way round: The number of colors is |
420 | 2^depth). | |
421 | ||
422 | You have to tell the kernel furthermore how the video memory is | |
423 | organized. This is done by a letter as <org> parameter: | |
424 | ||
425 | 'n': "normal planes", i.e. one whole plane after another | |
426 | 'i': "interleaved planes", i.e. 16 bit of the first plane, than 16 bit | |
427 | of the next, and so on... This mode is used only with the | |
428 | built-in Atari video modes, I think there is no card that | |
429 | supports this mode. | |
430 | 'p': "packed pixels", i.e. <depth> consecutive bits stand for all | |
431 | planes of one pixel; this is the most common mode for 8 planes | |
432 | (256 colors) on graphic cards | |
433 | 't': "true color" (more or less packed pixels, but without a color | |
434 | lookup table); usually depth is 24 | |
435 | ||
436 | For monochrome modes (i.e., <depth> is 1), the <org> letter has a | |
437 | different meaning: | |
438 | ||
439 | 'n': normal colors, i.e. 0=white, 1=black | |
440 | 'i': inverted colors, i.e. 0=black, 1=white | |
441 | ||
442 | The next important information about the video hardware is the base | |
443 | address of the video memory. That is given in the <scrmem> parameter, | |
444 | as a hexadecimal number with a "0x" prefix. You have to find out this | |
445 | address in the documentation of your hardware. | |
446 | ||
447 | The next parameter, <scrlen>, tells the kernel about the size of the | |
448 | video memory. If it's missing, the size is calculated from <xres>, | |
449 | <yres>, and <depth>. For now, it is not useful to write a value here. | |
450 | It would be used only for hardware scrolling (which isn't possible | |
451 | with the external driver, because the kernel cannot set the video base | |
452 | address), or for virtual resolutions under X (which the X server | |
453 | doesn't support yet). So, it's currently best to leave this field | |
454 | empty, either by ending the "external:" after the video address or by | |
455 | writing two consecutive semicolons, if you want to give a <vgabase> | |
456 | (it is allowed to leave this parameter empty). | |
457 | ||
458 | The <vgabase> parameter is optional. If it is not given, the kernel | |
459 | cannot read or write any color registers of the video hardware, and | |
460 | thus you have to set appropriate colors before you start Linux. But if | |
461 | your card is somehow VGA compatible, you can tell the kernel the base | |
462 | address of the VGA register set, so it can change the color lookup | |
463 | table. You have to look up this address in your board's documentation. | |
464 | To avoid misunderstandings: <vgabase> is the _base_ address, i.e. a 4k | |
465 | aligned address. For read/writing the color registers, the kernel | |
466 | uses the addresses vgabase+0x3c7...vgabase+0x3c9. The <vgabase> | |
467 | parameter is written in hexadecimal with a "0x" prefix, just as | |
468 | <scrmem>. | |
469 | ||
470 | <colw> is meaningful only if <vgabase> is specified. It tells the | |
471 | kernel how wide each of the color register is, i.e. the number of bits | |
472 | per single color (red/green/blue). Default is 6, another quite usual | |
473 | value is 8. | |
474 | ||
475 | Also <coltype> is used together with <vgabase>. It tells the kernel | |
476 | about the color register model of your gfx board. Currently, the types | |
477 | "vga" (which is also the default) and "mv300" (SANG MV300) are | |
478 | implemented. | |
479 | ||
480 | Parameter <xres_virtual> is required for ProMST or ET4000 cards where | |
481 | the physical linelength differs from the visible length. With ProMST, | |
482 | xres_virtual must be set to 2048. For ET4000, xres_virtual depends on the | |
483 | initialisation of the video-card. | |
484 | If you're missing a corresponding yres_virtual: the external part is legacy, | |
485 | therefore we don't support hardware-dependent functions like hardware-scroll, | |
486 | panning or blanking. | |
487 | ||
488 | 4.1.7) eclock: | |
489 | -------------- | |
490 | ||
491 | The external pixel clock attached to the Falcon VIDEL shifter. This | |
492 | currently works only with the ScreenWonder! | |
493 | ||
494 | 4.1.8) monitorcap: | |
495 | ------------------- | |
496 | ||
497 | Syntax: monitorcap:<vmin>;<vmax>;<hmin>;<hmax> | |
498 | ||
499 | This describes the capabilities of a multisync monitor. Don't use it | |
500 | with a fixed-frequency monitor! For now, only the Falcon frame buffer | |
501 | uses the settings of "monitorcap:". | |
502 | ||
503 | <vmin> and <vmax> are the minimum and maximum, resp., vertical frequencies | |
504 | your monitor can work with, in Hz. <hmin> and <hmax> are the same for | |
505 | the horizontal frequency, in kHz. | |
506 | ||
507 | The defaults are 58;62;31;32 (VGA compatible). | |
508 | ||
509 | The defaults for TV/SC1224/SC1435 cover both PAL and NTSC standards. | |
510 | ||
511 | 4.1.9) keep | |
512 | ------------ | |
513 | ||
514 | If this option is given, the framebuffer device doesn't do any video | |
515 | mode calculations and settings on its own. The only Atari fb device | |
516 | that does this currently is the Falcon. | |
517 | ||
518 | What you reach with this: Settings for unknown video extensions | |
519 | aren't overridden by the driver, so you can still use the mode found | |
520 | when booting, when the driver doesn't know to set this mode itself. | |
521 | But this also means, that you can't switch video modes anymore... | |
522 | ||
523 | An example where you may want to use "keep" is the ScreenBlaster for | |
524 | the Falcon. | |
525 | ||
526 | ||
527 | 4.2) atamouse= | |
528 | -------------- | |
529 | ||
530 | Syntax: atamouse=<x-threshold>,[<y-threshold>] | |
531 | ||
532 | With this option, you can set the mouse movement reporting threshold. | |
533 | This is the number of pixels of mouse movement that have to accumulate | |
534 | before the IKBD sends a new mouse packet to the kernel. Higher values | |
535 | reduce the mouse interrupt load and thus reduce the chance of keyboard | |
536 | overruns. Lower values give a slightly faster mouse responses and | |
537 | slightly better mouse tracking. | |
538 | ||
539 | You can set the threshold in x and y separately, but usually this is | |
540 | of little practical use. If there's just one number in the option, it | |
541 | is used for both dimensions. The default value is 2 for both | |
542 | thresholds. | |
543 | ||
544 | ||
545 | 4.3) ataflop= | |
546 | ------------- | |
547 | ||
548 | Syntax: ataflop=<drive type>[,<trackbuffering>[,<steprateA>[,<steprateB>]]] | |
549 | ||
550 | The drive type may be 0, 1, or 2, for DD, HD, and ED, resp. This | |
551 | setting affects how many buffers are reserved and which formats are | |
552 | probed (see also below). The default is 1 (HD). Only one drive type | |
553 | can be selected. If you have two disk drives, select the "better" | |
554 | type. | |
555 | ||
556 | The second parameter <trackbuffer> tells the kernel whether to use | |
557 | track buffering (1) or not (0). The default is machine-dependent: | |
558 | no for the Medusa and yes for all others. | |
559 | ||
560 | With the two following parameters, you can change the default | |
561 | steprate used for drive A and B, resp. | |
562 | ||
563 | ||
564 | 4.4) atascsi= | |
565 | ------------- | |
566 | ||
567 | Syntax: atascsi=<can_queue>[,<cmd_per_lun>[,<scat-gat>[,<host-id>[,<tagged>]]]] | |
568 | ||
569 | This option sets some parameters for the Atari native SCSI driver. | |
570 | Generally, any number of arguments can be omitted from the end. And | |
571 | for each of the numbers, a negative value means "use default". The | |
572 | defaults depend on whether TT-style or Falcon-style SCSI is used. | |
573 | Below, defaults are noted as n/m, where the first value refers to | |
574 | TT-SCSI and the latter to Falcon-SCSI. If an illegal value is given | |
575 | for one parameter, an error message is printed and that one setting is | |
576 | ignored (others aren't affected). | |
577 | ||
578 | <can_queue>: | |
579 | This is the maximum number of SCSI commands queued internally to the | |
580 | Atari SCSI driver. A value of 1 effectively turns off the driver | |
581 | internal multitasking (if it causes problems). Legal values are >= | |
582 | 1. <can_queue> can be as high as you like, but values greater than | |
583 | <cmd_per_lun> times the number of SCSI targets (LUNs) you have | |
584 | don't make sense. Default: 16/8. | |
585 | ||
586 | <cmd_per_lun>: | |
587 | Maximum number of SCSI commands issued to the driver for one | |
588 | logical unit (LUN, usually one SCSI target). Legal values start | |
589 | from 1. If tagged queuing (see below) is not used, values greater | |
590 | than 2 don't make sense, but waste memory. Otherwise, the maximum | |
591 | is the number of command tags available to the driver (currently | |
592 | 32). Default: 8/1. (Note: Values > 1 seem to cause problems on a | |
593 | Falcon, cause not yet known.) | |
594 | ||
595 | The <cmd_per_lun> value at a great part determines the amount of | |
596 | memory SCSI reserves for itself. The formula is rather | |
597 | complicated, but I can give you some hints: | |
598 | no scatter-gather : cmd_per_lun * 232 bytes | |
599 | full scatter-gather: cmd_per_lun * approx. 17 Kbytes | |
600 | ||
601 | <scat-gat>: | |
602 | Size of the scatter-gather table, i.e. the number of requests | |
603 | consecutive on the disk that can be merged into one SCSI command. | |
604 | Legal values are between 0 and 255. Default: 255/0. Note: This | |
605 | value is forced to 0 on a Falcon, since scatter-gather isn't | |
606 | possible with the ST-DMA. Not using scatter-gather hurts | |
607 | performance significantly. | |
608 | ||
609 | <host-id>: | |
610 | The SCSI ID to be used by the initiator (your Atari). This is | |
611 | usually 7, the highest possible ID. Every ID on the SCSI bus must | |
612 | be unique. Default: determined at run time: If the NV-RAM checksum | |
613 | is valid, and bit 7 in byte 30 of the NV-RAM is set, the lower 3 | |
614 | bits of this byte are used as the host ID. (This method is defined | |
615 | by Atari and also used by some TOS HD drivers.) If the above | |
616 | isn't given, the default ID is 7. (both, TT and Falcon). | |
617 | ||
618 | <tagged>: | |
619 | 0 means turn off tagged queuing support, all other values > 0 mean | |
620 | use tagged queuing for targets that support it. Default: currently | |
621 | off, but this may change when tagged queuing handling has been | |
622 | proved to be reliable. | |
623 | ||
624 | Tagged queuing means that more than one command can be issued to | |
625 | one LUN, and the SCSI device itself orders the requests so they | |
626 | can be performed in optimal order. Not all SCSI devices support | |
627 | tagged queuing (:-(). | |
628 | ||
f9c98d02 | 629 | 4.5 switches= |
1da177e4 LT |
630 | ------------- |
631 | ||
632 | Syntax: switches=<list of switches> | |
633 | ||
634 | With this option you can switch some hardware lines that are often | |
635 | used to enable/disable certain hardware extensions. Examples are | |
636 | OverScan, overclocking, ... | |
637 | ||
638 | The <list of switches> is a comma-separated list of the following | |
639 | items: | |
640 | ||
641 | ikbd: set RTS of the keyboard ACIA high | |
642 | midi: set RTS of the MIDI ACIA high | |
643 | snd6: set bit 6 of the PSG port A | |
644 | snd7: set bit 6 of the PSG port A | |
645 | ||
646 | It doesn't make sense to mention a switch more than once (no | |
647 | difference to only once), but you can give as many switches as you | |
648 | want to enable different features. The switch lines are set as early | |
649 | as possible during kernel initialization (even before determining the | |
650 | present hardware.) | |
651 | ||
652 | All of the items can also be prefixed with "ov_", i.e. "ov_ikbd", | |
653 | "ov_midi", ... These options are meant for switching on an OverScan | |
654 | video extension. The difference to the bare option is that the | |
655 | switch-on is done after video initialization, and somehow synchronized | |
656 | to the HBLANK. A speciality is that ov_ikbd and ov_midi are switched | |
657 | off before rebooting, so that OverScan is disabled and TOS boots | |
658 | correctly. | |
659 | ||
660 | If you give an option both, with and without the "ov_" prefix, the | |
661 | earlier initialization ("ov_"-less) takes precedence. But the | |
662 | switching-off on reset still happens in this case. | |
663 | ||
1da177e4 LT |
664 | 5) Options for Amiga Only: |
665 | ========================== | |
666 | ||
667 | 5.1) video= | |
668 | ----------- | |
669 | ||
670 | Syntax: video=<fbname>:<sub-options...> | |
671 | ||
672 | The <fbname> parameter specifies the name of the frame buffer, valid | |
673 | options are `amifb', `cyber', 'virge', `retz3' and `clgen', provided | |
674 | that the respective frame buffer devices have been compiled into the | |
675 | kernel (or compiled as loadable modules). The behavior of the <fbname> | |
676 | option was changed in 2.1.57 so it is now recommended to specify this | |
677 | option. | |
678 | ||
679 | The <sub-options> is a comma-separated list of the sub-options listed | |
680 | below. This option is organized similar to the Atari version of the | |
681 | "video"-option (4.1), but knows fewer sub-options. | |
682 | ||
683 | 5.1.1) video mode | |
684 | ----------------- | |
685 | ||
686 | Again, similar to the video mode for the Atari (see 4.1.1). Predefined | |
687 | modes depend on the used frame buffer device. | |
688 | ||
689 | OCS, ECS and AGA machines all use the color frame buffer. The following | |
690 | predefined video modes are available: | |
691 | ||
692 | NTSC modes: | |
693 | - ntsc : 640x200, 15 kHz, 60 Hz | |
694 | - ntsc-lace : 640x400, 15 kHz, 60 Hz interlaced | |
695 | PAL modes: | |
696 | - pal : 640x256, 15 kHz, 50 Hz | |
697 | - pal-lace : 640x512, 15 kHz, 50 Hz interlaced | |
698 | ECS modes: | |
699 | - multiscan : 640x480, 29 kHz, 57 Hz | |
700 | - multiscan-lace : 640x960, 29 kHz, 57 Hz interlaced | |
701 | - euro36 : 640x200, 15 kHz, 72 Hz | |
702 | - euro36-lace : 640x400, 15 kHz, 72 Hz interlaced | |
703 | - euro72 : 640x400, 29 kHz, 68 Hz | |
704 | - euro72-lace : 640x800, 29 kHz, 68 Hz interlaced | |
705 | - super72 : 800x300, 23 kHz, 70 Hz | |
706 | - super72-lace : 800x600, 23 kHz, 70 Hz interlaced | |
707 | - dblntsc-ff : 640x400, 27 kHz, 57 Hz | |
708 | - dblntsc-lace : 640x800, 27 kHz, 57 Hz interlaced | |
709 | - dblpal-ff : 640x512, 27 kHz, 47 Hz | |
710 | - dblpal-lace : 640x1024, 27 kHz, 47 Hz interlaced | |
711 | - dblntsc : 640x200, 27 kHz, 57 Hz doublescan | |
712 | - dblpal : 640x256, 27 kHz, 47 Hz doublescan | |
713 | VGA modes: | |
714 | - vga : 640x480, 31 kHz, 60 Hz | |
715 | - vga70 : 640x400, 31 kHz, 70 Hz | |
716 | ||
717 | Please notice that the ECS and VGA modes require either an ECS or AGA | |
718 | chipset, and that these modes are limited to 2-bit color for the ECS | |
719 | chipset and 8-bit color for the AGA chipset. | |
720 | ||
721 | 5.1.2) depth | |
722 | ------------ | |
723 | ||
724 | Syntax: depth:<nr. of bit-planes> | |
725 | ||
726 | Specify the number of bit-planes for the selected video-mode. | |
727 | ||
728 | 5.1.3) inverse | |
729 | -------------- | |
730 | ||
731 | Use inverted display (black on white). Functionally the same as the | |
732 | "inverse" sub-option for the Atari. | |
733 | ||
734 | 5.1.4) font | |
735 | ----------- | |
736 | ||
737 | Syntax: font:<fontname> | |
738 | ||
739 | Specify the font to use in text modes. Functionally the same as the | |
740 | "font" sub-option for the Atari, except that `PEARL8x8' is used instead | |
741 | of `VGA8x8' if the vertical size of the display is less than 400 pixel | |
742 | rows. | |
743 | ||
744 | 5.1.5) monitorcap: | |
745 | ------------------- | |
746 | ||
747 | Syntax: monitorcap:<vmin>;<vmax>;<hmin>;<hmax> | |
748 | ||
749 | This describes the capabilities of a multisync monitor. For now, only | |
750 | the color frame buffer uses the settings of "monitorcap:". | |
751 | ||
752 | <vmin> and <vmax> are the minimum and maximum, resp., vertical frequencies | |
753 | your monitor can work with, in Hz. <hmin> and <hmax> are the same for | |
754 | the horizontal frequency, in kHz. | |
755 | ||
756 | The defaults are 50;90;15;38 (Generic Amiga multisync monitor). | |
757 | ||
758 | ||
759 | 5.2) fd_def_df0= | |
760 | ---------------- | |
761 | ||
762 | Syntax: fd_def_df0=<value> | |
763 | ||
764 | Sets the df0 value for "silent" floppy drives. The value should be in | |
765 | hexadecimal with "0x" prefix. | |
766 | ||
767 | ||
768 | 5.3) wd33c93= | |
769 | ------------- | |
770 | ||
771 | Syntax: wd33c93=<sub-options...> | |
772 | ||
773 | These options affect the A590/A2091, A3000 and GVP Series II SCSI | |
774 | controllers. | |
775 | ||
776 | The <sub-options> is a comma-separated list of the sub-options listed | |
777 | below. | |
778 | ||
779 | 5.3.1) nosync | |
780 | ------------- | |
781 | ||
782 | Syntax: nosync:bitmask | |
783 | ||
784 | bitmask is a byte where the 1st 7 bits correspond with the 7 | |
785 | possible SCSI devices. Set a bit to prevent sync negotiation on that | |
786 | device. To maintain backwards compatibility, a command-line such as | |
787 | "wd33c93=255" will be automatically translated to | |
788 | "wd33c93=nosync:0xff". The default is to disable sync negotiation for | |
789 | all devices, eg. nosync:0xff. | |
790 | ||
791 | 5.3.2) period | |
792 | ------------- | |
793 | ||
794 | Syntax: period:ns | |
795 | ||
796 | `ns' is the minimum # of nanoseconds in a SCSI data transfer | |
797 | period. Default is 500; acceptable values are 250 - 1000. | |
798 | ||
799 | 5.3.3) disconnect | |
800 | ----------------- | |
801 | ||
802 | Syntax: disconnect:x | |
803 | ||
804 | Specify x = 0 to never allow disconnects, 2 to always allow them. | |
805 | x = 1 does 'adaptive' disconnects, which is the default and generally | |
806 | the best choice. | |
807 | ||
808 | 5.3.4) debug | |
809 | ------------ | |
810 | ||
811 | Syntax: debug:x | |
812 | ||
813 | If `DEBUGGING_ON' is defined, x is a bit mask that causes various | |
814 | types of debug output to printed - see the DB_xxx defines in | |
815 | wd33c93.h. | |
816 | ||
817 | 5.3.5) clock | |
818 | ------------ | |
819 | ||
820 | Syntax: clock:x | |
821 | ||
822 | x = clock input in MHz for WD33c93 chip. Normal values would be from | |
823 | 8 through 20. The default value depends on your hostadapter(s), | |
824 | default for the A3000 internal controller is 14, for the A2091 it's 8 | |
825 | and for the GVP hostadapters it's either 8 or 14, depending on the | |
826 | hostadapter and the SCSI-clock jumper present on some GVP | |
827 | hostadapters. | |
828 | ||
829 | 5.3.6) next | |
830 | ----------- | |
831 | ||
832 | No argument. Used to separate blocks of keywords when there's more | |
833 | than one wd33c93-based host adapter in the system. | |
834 | ||
835 | 5.3.7) nodma | |
836 | ------------ | |
837 | ||
838 | Syntax: nodma:x | |
839 | ||
840 | If x is 1 (or if the option is just written as "nodma"), the WD33c93 | |
841 | controller will not use DMA (= direct memory access) to access the | |
842 | Amiga's memory. This is useful for some systems (like A3000's and | |
843 | A4000's with the A3640 accelerator, revision 3.0) that have problems | |
844 | using DMA to chip memory. The default is 0, i.e. to use DMA if | |
845 | possible. | |
846 | ||
847 | ||
848 | 5.4) gvp11= | |
849 | ----------- | |
850 | ||
851 | Syntax: gvp11=<addr-mask> | |
852 | ||
853 | The earlier versions of the GVP driver did not handle DMA | |
854 | address-mask settings correctly which made it necessary for some | |
855 | people to use this option, in order to get their GVP controller | |
856 | running under Linux. These problems have hopefully been solved and the | |
857 | use of this option is now highly unrecommended! | |
858 | ||
859 | Incorrect use can lead to unpredictable behavior, so please only use | |
860 | this option if you *know* what you are doing and have a reason to do | |
861 | so. In any case if you experience problems and need to use this | |
862 | option, please inform us about it by mailing to the Linux/68k kernel | |
863 | mailing list. | |
864 | ||
865 | The address mask set by this option specifies which addresses are | |
866 | valid for DMA with the GVP Series II SCSI controller. An address is | |
867 | valid, if no bits are set except the bits that are set in the mask, | |
868 | too. | |
869 | ||
870 | Some versions of the GVP can only DMA into a 24 bit address range, | |
871 | some can address a 25 bit address range while others can use the whole | |
872 | 32 bit address range for DMA. The correct setting depends on your | |
873 | controller and should be autodetected by the driver. An example is the | |
874 | 24 bit region which is specified by a mask of 0x00fffffe. | |
875 | ||
876 | ||
877 | 5.5) 53c7xx= | |
878 | ------------ | |
879 | ||
880 | Syntax: 53c7xx=<sub-options...> | |
881 | ||
882 | These options affect the A4000T, A4091, WarpEngine, Blizzard 603e+, | |
883 | and GForce 040/060 SCSI controllers on the Amiga, as well as the | |
884 | builtin MVME 16x SCSI controller. | |
885 | ||
886 | The <sub-options> is a comma-separated list of the sub-options listed | |
887 | below. | |
888 | ||
889 | 5.5.1) nosync | |
890 | ------------- | |
891 | ||
892 | Syntax: nosync:0 | |
893 | ||
894 | Disables sync negotiation for all devices. Any value after the | |
895 | colon is acceptable (and has the same effect). | |
896 | ||
897 | 5.5.2) noasync | |
898 | -------------- | |
899 | ||
900 | Syntax: noasync:0 | |
901 | ||
902 | Disables async and sync negotiation for all devices. Any value | |
903 | after the colon is acceptable (and has the same effect). | |
904 | ||
905 | 5.5.3) nodisconnect | |
906 | ------------------- | |
907 | ||
908 | Syntax: nodisconnect:0 | |
909 | ||
910 | Disables SCSI disconnects. Any value after the colon is acceptable | |
911 | (and has the same effect). | |
912 | ||
913 | 5.5.4) validids | |
914 | --------------- | |
915 | ||
916 | Syntax: validids:0xNN | |
917 | ||
918 | Specify which SCSI ids the driver should pay attention to. This is | |
919 | a bitmask (i.e. to only pay attention to ID#4, you'd use 0x10). | |
920 | Default is 0x7f (devices 0-6). | |
921 | ||
922 | 5.5.5) opthi | |
923 | 5.5.6) optlo | |
924 | ------------ | |
925 | ||
926 | Syntax: opthi:M,optlo:N | |
927 | ||
928 | Specify options for "hostdata->options". The acceptable definitions | |
929 | are listed in drivers/scsi/53c7xx.h; the 32 high bits should be in | |
930 | opthi and the 32 low bits in optlo. They must be specified in the | |
931 | order opthi=M,optlo=N. | |
932 | ||
933 | 5.5.7) next | |
934 | ----------- | |
935 | ||
936 | No argument. Used to separate blocks of keywords when there's more | |
937 | than one 53c7xx host adapter in the system. | |
938 | ||
939 | ||
940 | /* Local Variables: */ | |
941 | /* mode: text */ | |
942 | /* End: */ |