Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | /proc/sys/net/ipv4/* Variables: |
2 | ||
3 | ip_forward - BOOLEAN | |
4 | 0 - disabled (default) | |
5 | not 0 - enabled | |
6 | ||
7 | Forward Packets between interfaces. | |
8 | ||
9 | This variable is special, its change resets all configuration | |
10 | parameters to their default state (RFC1122 for hosts, RFC1812 | |
11 | for routers) | |
12 | ||
13 | ip_default_ttl - INTEGER | |
14 | default 64 | |
15 | ||
16 | ip_no_pmtu_disc - BOOLEAN | |
17 | Disable Path MTU Discovery. | |
18 | default FALSE | |
19 | ||
20 | min_pmtu - INTEGER | |
21 | default 562 - minimum discovered Path MTU | |
22 | ||
23 | mtu_expires - INTEGER | |
24 | Time, in seconds, that cached PMTU information is kept. | |
25 | ||
26 | min_adv_mss - INTEGER | |
27 | The advertised MSS depends on the first hop route MTU, but will | |
28 | never be lower than this setting. | |
29 | ||
30 | IP Fragmentation: | |
31 | ||
32 | ipfrag_high_thresh - INTEGER | |
33 | Maximum memory used to reassemble IP fragments. When | |
34 | ipfrag_high_thresh bytes of memory is allocated for this purpose, | |
35 | the fragment handler will toss packets until ipfrag_low_thresh | |
36 | is reached. | |
37 | ||
38 | ipfrag_low_thresh - INTEGER | |
39 | See ipfrag_high_thresh | |
40 | ||
41 | ipfrag_time - INTEGER | |
42 | Time in seconds to keep an IP fragment in memory. | |
43 | ||
44 | ipfrag_secret_interval - INTEGER | |
45 | Regeneration interval (in seconds) of the hash secret (or lifetime | |
46 | for the hash secret) for IP fragments. | |
47 | Default: 600 | |
48 | ||
89cee8b1 HX |
49 | ipfrag_max_dist - INTEGER |
50 | ipfrag_max_dist is a non-negative integer value which defines the | |
51 | maximum "disorder" which is allowed among fragments which share a | |
52 | common IP source address. Note that reordering of packets is | |
53 | not unusual, but if a large number of fragments arrive from a source | |
54 | IP address while a particular fragment queue remains incomplete, it | |
55 | probably indicates that one or more fragments belonging to that queue | |
56 | have been lost. When ipfrag_max_dist is positive, an additional check | |
57 | is done on fragments before they are added to a reassembly queue - if | |
58 | ipfrag_max_dist (or more) fragments have arrived from a particular IP | |
59 | address between additions to any IP fragment queue using that source | |
60 | address, it's presumed that one or more fragments in the queue are | |
61 | lost. The existing fragment queue will be dropped, and a new one | |
62 | started. An ipfrag_max_dist value of zero disables this check. | |
63 | ||
64 | Using a very small value, e.g. 1 or 2, for ipfrag_max_dist can | |
65 | result in unnecessarily dropping fragment queues when normal | |
66 | reordering of packets occurs, which could lead to poor application | |
67 | performance. Using a very large value, e.g. 50000, increases the | |
68 | likelihood of incorrectly reassembling IP fragments that originate | |
69 | from different IP datagrams, which could result in data corruption. | |
70 | Default: 64 | |
71 | ||
1da177e4 LT |
72 | INET peer storage: |
73 | ||
74 | inet_peer_threshold - INTEGER | |
75 | The approximate size of the storage. Starting from this threshold | |
76 | entries will be thrown aggressively. This threshold also determines | |
77 | entries' time-to-live and time intervals between garbage collection | |
78 | passes. More entries, less time-to-live, less GC interval. | |
79 | ||
80 | inet_peer_minttl - INTEGER | |
81 | Minimum time-to-live of entries. Should be enough to cover fragment | |
82 | time-to-live on the reassembling side. This minimum time-to-live is | |
83 | guaranteed if the pool size is less than inet_peer_threshold. | |
77a538d5 | 84 | Measured in seconds. |
1da177e4 LT |
85 | |
86 | inet_peer_maxttl - INTEGER | |
87 | Maximum time-to-live of entries. Unused entries will expire after | |
88 | this period of time if there is no memory pressure on the pool (i.e. | |
89 | when the number of entries in the pool is very small). | |
77a538d5 | 90 | Measured in seconds. |
1da177e4 LT |
91 | |
92 | inet_peer_gc_mintime - INTEGER | |
93 | Minimum interval between garbage collection passes. This interval is | |
94 | in effect under high memory pressure on the pool. | |
77a538d5 | 95 | Measured in seconds. |
1da177e4 LT |
96 | |
97 | inet_peer_gc_maxtime - INTEGER | |
98 | Minimum interval between garbage collection passes. This interval is | |
99 | in effect under low (or absent) memory pressure on the pool. | |
77a538d5 | 100 | Measured in seconds. |
1da177e4 LT |
101 | |
102 | TCP variables: | |
103 | ||
ef56e622 SH |
104 | somaxconn - INTEGER |
105 | Limit of socket listen() backlog, known in userspace as SOMAXCONN. | |
106 | Defaults to 128. See also tcp_max_syn_backlog for additional tuning | |
107 | for TCP sockets. | |
108 | ||
9772efb9 | 109 | tcp_abc - INTEGER |
b3a8a40d SH |
110 | Controls Appropriate Byte Count (ABC) defined in RFC3465. |
111 | ABC is a way of increasing congestion window (cwnd) more slowly | |
112 | in response to partial acknowledgments. | |
113 | Possible values are: | |
114 | 0 increase cwnd once per acknowledgment (no ABC) | |
115 | 1 increase cwnd once per acknowledgment of full sized segment | |
116 | 2 allow increase cwnd by two if acknowledgment is | |
117 | of two segments to compensate for delayed acknowledgments. | |
118 | Default: 0 (off) | |
9772efb9 | 119 | |
ef56e622 SH |
120 | tcp_abort_on_overflow - BOOLEAN |
121 | If listening service is too slow to accept new connections, | |
122 | reset them. Default state is FALSE. It means that if overflow | |
123 | occurred due to a burst, connection will recover. Enable this | |
124 | option _only_ if you are really sure that listening daemon | |
125 | cannot be tuned to accept connections faster. Enabling this | |
126 | option can harm clients of your server. | |
1da177e4 | 127 | |
ef56e622 SH |
128 | tcp_adv_win_scale - INTEGER |
129 | Count buffering overhead as bytes/2^tcp_adv_win_scale | |
130 | (if tcp_adv_win_scale > 0) or bytes-bytes/2^(-tcp_adv_win_scale), | |
131 | if it is <= 0. | |
132 | Default: 2 | |
1da177e4 | 133 | |
ef56e622 SH |
134 | tcp_allowed_congestion_control - STRING |
135 | Show/set the congestion control choices available to non-privileged | |
136 | processes. The list is a subset of those listed in | |
137 | tcp_available_congestion_control. | |
138 | Default is "reno" and the default setting (tcp_congestion_control). | |
1da177e4 | 139 | |
ef56e622 SH |
140 | tcp_app_win - INTEGER |
141 | Reserve max(window/2^tcp_app_win, mss) of window for application | |
142 | buffer. Value 0 is special, it means that nothing is reserved. | |
143 | Default: 31 | |
1da177e4 | 144 | |
ef56e622 SH |
145 | tcp_available_congestion_control - STRING |
146 | Shows the available congestion control choices that are registered. | |
147 | More congestion control algorithms may be available as modules, | |
148 | but not loaded. | |
1da177e4 | 149 | |
71599cd1 | 150 | tcp_base_mss - INTEGER |
4edc2f34 SH |
151 | The initial value of search_low to be used by the packetization layer |
152 | Path MTU discovery (MTU probing). If MTU probing is enabled, | |
153 | this is the initial MSS used by the connection. | |
71599cd1 | 154 | |
ef56e622 SH |
155 | tcp_congestion_control - STRING |
156 | Set the congestion control algorithm to be used for new | |
157 | connections. The algorithm "reno" is always available, but | |
158 | additional choices may be available based on kernel configuration. | |
159 | Default is set as part of kernel configuration. | |
1da177e4 | 160 | |
ef56e622 SH |
161 | tcp_dsack - BOOLEAN |
162 | Allows TCP to send "duplicate" SACKs. | |
1da177e4 | 163 | |
ef56e622 SH |
164 | tcp_ecn - BOOLEAN |
165 | Enable Explicit Congestion Notification in TCP. | |
166 | ||
167 | tcp_fack - BOOLEAN | |
168 | Enable FACK congestion avoidance and fast retransmission. | |
169 | The value is not used, if tcp_sack is not enabled. | |
1da177e4 LT |
170 | |
171 | tcp_fin_timeout - INTEGER | |
172 | Time to hold socket in state FIN-WAIT-2, if it was closed | |
173 | by our side. Peer can be broken and never close its side, | |
174 | or even died unexpectedly. Default value is 60sec. | |
175 | Usual value used in 2.2 was 180 seconds, you may restore | |
176 | it, but remember that if your machine is even underloaded WEB server, | |
177 | you risk to overflow memory with kilotons of dead sockets, | |
178 | FIN-WAIT-2 sockets are less dangerous than FIN-WAIT-1, | |
179 | because they eat maximum 1.5K of memory, but they tend | |
180 | to live longer. Cf. tcp_max_orphans. | |
181 | ||
89808060 | 182 | tcp_frto - INTEGER |
cd99889c IJ |
183 | Enables Forward RTO-Recovery (F-RTO) defined in RFC4138. |
184 | F-RTO is an enhanced recovery algorithm for TCP retransmission | |
ef56e622 SH |
185 | timeouts. It is particularly beneficial in wireless environments |
186 | where packet loss is typically due to random radio interference | |
564262c1 | 187 | rather than intermediate router congestion. F-RTO is sender-side |
4edc2f34 SH |
188 | only modification. Therefore it does not require any support from |
189 | the peer. | |
190 | ||
cd99889c IJ |
191 | If set to 1, basic version is enabled. 2 enables SACK enhanced |
192 | F-RTO if flow uses SACK. The basic version can be used also when | |
564262c1 | 193 | SACK is in use though scenario(s) with it exists where F-RTO |
cd99889c IJ |
194 | interacts badly with the packet counting of the SACK enabled TCP |
195 | flow. | |
1da177e4 | 196 | |
89808060 IJ |
197 | tcp_frto_response - INTEGER |
198 | When F-RTO has detected that a TCP retransmission timeout was | |
199 | spurious (i.e, the timeout would have been avoided had TCP set a | |
200 | longer retransmission timeout), TCP has several options what to do | |
201 | next. Possible values are: | |
202 | 0 Rate halving based; a smooth and conservative response, | |
203 | results in halved cwnd and ssthresh after one RTT | |
204 | 1 Very conservative response; not recommended because even | |
205 | though being valid, it interacts poorly with the rest of | |
206 | Linux TCP, halves cwnd and ssthresh immediately | |
207 | 2 Aggressive response; undoes congestion control measures | |
208 | that are now known to be unnecessary (ignoring the | |
209 | possibility of a lost retransmission that would require | |
210 | TCP to be more cautious), cwnd and ssthresh are restored | |
211 | to the values prior timeout | |
212 | Default: 0 (rate halving based) | |
213 | ||
ef56e622 SH |
214 | tcp_keepalive_time - INTEGER |
215 | How often TCP sends out keepalive messages when keepalive is enabled. | |
216 | Default: 2hours. | |
1da177e4 | 217 | |
ef56e622 SH |
218 | tcp_keepalive_probes - INTEGER |
219 | How many keepalive probes TCP sends out, until it decides that the | |
220 | connection is broken. Default value: 9. | |
221 | ||
222 | tcp_keepalive_intvl - INTEGER | |
223 | How frequently the probes are send out. Multiplied by | |
224 | tcp_keepalive_probes it is time to kill not responding connection, | |
225 | after probes started. Default value: 75sec i.e. connection | |
226 | will be aborted after ~11 minutes of retries. | |
227 | ||
228 | tcp_low_latency - BOOLEAN | |
229 | If set, the TCP stack makes decisions that prefer lower | |
230 | latency as opposed to higher throughput. By default, this | |
231 | option is not set meaning that higher throughput is preferred. | |
232 | An example of an application where this default should be | |
233 | changed would be a Beowulf compute cluster. | |
234 | Default: 0 | |
1da177e4 LT |
235 | |
236 | tcp_max_orphans - INTEGER | |
237 | Maximal number of TCP sockets not attached to any user file handle, | |
238 | held by system. If this number is exceeded orphaned connections are | |
239 | reset immediately and warning is printed. This limit exists | |
240 | only to prevent simple DoS attacks, you _must_ not rely on this | |
241 | or lower the limit artificially, but rather increase it | |
242 | (probably, after increasing installed memory), | |
243 | if network conditions require more than default value, | |
244 | and tune network services to linger and kill such states | |
245 | more aggressively. Let me to remind again: each orphan eats | |
246 | up to ~64K of unswappable memory. | |
247 | ||
1da177e4 LT |
248 | tcp_max_syn_backlog - INTEGER |
249 | Maximal number of remembered connection requests, which are | |
250 | still did not receive an acknowledgment from connecting client. | |
251 | Default value is 1024 for systems with more than 128Mb of memory, | |
252 | and 128 for low memory machines. If server suffers of overload, | |
253 | try to increase this number. | |
254 | ||
ef56e622 SH |
255 | tcp_max_tw_buckets - INTEGER |
256 | Maximal number of timewait sockets held by system simultaneously. | |
257 | If this number is exceeded time-wait socket is immediately destroyed | |
258 | and warning is printed. This limit exists only to prevent | |
259 | simple DoS attacks, you _must_ not lower the limit artificially, | |
260 | but rather increase it (probably, after increasing installed memory), | |
261 | if network conditions require more than default value. | |
1da177e4 | 262 | |
ef56e622 SH |
263 | tcp_mem - vector of 3 INTEGERs: min, pressure, max |
264 | min: below this number of pages TCP is not bothered about its | |
265 | memory appetite. | |
1da177e4 | 266 | |
ef56e622 SH |
267 | pressure: when amount of memory allocated by TCP exceeds this number |
268 | of pages, TCP moderates its memory consumption and enters memory | |
269 | pressure mode, which is exited when memory consumption falls | |
270 | under "min". | |
1da177e4 | 271 | |
ef56e622 | 272 | max: number of pages allowed for queueing by all TCP sockets. |
1da177e4 | 273 | |
ef56e622 SH |
274 | Defaults are calculated at boot time from amount of available |
275 | memory. | |
1da177e4 | 276 | |
71599cd1 | 277 | tcp_moderate_rcvbuf - BOOLEAN |
4edc2f34 | 278 | If set, TCP performs receive buffer auto-tuning, attempting to |
71599cd1 JH |
279 | automatically size the buffer (no greater than tcp_rmem[2]) to |
280 | match the size required by the path for full throughput. Enabled by | |
281 | default. | |
282 | ||
283 | tcp_mtu_probing - INTEGER | |
284 | Controls TCP Packetization-Layer Path MTU Discovery. Takes three | |
285 | values: | |
286 | 0 - Disabled | |
287 | 1 - Disabled by default, enabled when an ICMP black hole detected | |
288 | 2 - Always enabled, use initial MSS of tcp_base_mss. | |
289 | ||
290 | tcp_no_metrics_save - BOOLEAN | |
291 | By default, TCP saves various connection metrics in the route cache | |
292 | when the connection closes, so that connections established in the | |
293 | near future can use these to set initial conditions. Usually, this | |
294 | increases overall performance, but may sometimes cause performance | |
0f035b8e | 295 | degradation. If set, TCP will not cache metrics on closing |
71599cd1 JH |
296 | connections. |
297 | ||
ef56e622 SH |
298 | tcp_orphan_retries - INTEGER |
299 | How may times to retry before killing TCP connection, closed | |
300 | by our side. Default value 7 corresponds to ~50sec-16min | |
301 | depending on RTO. If you machine is loaded WEB server, | |
302 | you should think about lowering this value, such sockets | |
303 | may consume significant resources. Cf. tcp_max_orphans. | |
1da177e4 LT |
304 | |
305 | tcp_reordering - INTEGER | |
306 | Maximal reordering of packets in a TCP stream. | |
307 | Default: 3 | |
308 | ||
309 | tcp_retrans_collapse - BOOLEAN | |
310 | Bug-to-bug compatibility with some broken printers. | |
311 | On retransmit try to send bigger packets to work around bugs in | |
312 | certain TCP stacks. | |
313 | ||
ef56e622 SH |
314 | tcp_retries1 - INTEGER |
315 | How many times to retry before deciding that something is wrong | |
316 | and it is necessary to report this suspicion to network layer. | |
317 | Minimal RFC value is 3, it is default, which corresponds | |
318 | to ~3sec-8min depending on RTO. | |
1da177e4 | 319 | |
ef56e622 SH |
320 | tcp_retries2 - INTEGER |
321 | How may times to retry before killing alive TCP connection. | |
322 | RFC1122 says that the limit should be longer than 100 sec. | |
323 | It is too small number. Default value 15 corresponds to ~13-30min | |
324 | depending on RTO. | |
1da177e4 | 325 | |
ef56e622 SH |
326 | tcp_rfc1337 - BOOLEAN |
327 | If set, the TCP stack behaves conforming to RFC1337. If unset, | |
328 | we are not conforming to RFC, but prevent TCP TIME_WAIT | |
329 | assassination. | |
330 | Default: 0 | |
1da177e4 LT |
331 | |
332 | tcp_rmem - vector of 3 INTEGERs: min, default, max | |
333 | min: Minimal size of receive buffer used by TCP sockets. | |
334 | It is guaranteed to each TCP socket, even under moderate memory | |
335 | pressure. | |
336 | Default: 8K | |
337 | ||
53025f5e | 338 | default: initial size of receive buffer used by TCP sockets. |
1da177e4 LT |
339 | This value overrides net.core.rmem_default used by other protocols. |
340 | Default: 87380 bytes. This value results in window of 65535 with | |
341 | default setting of tcp_adv_win_scale and tcp_app_win:0 and a bit | |
342 | less for default tcp_app_win. See below about these variables. | |
343 | ||
344 | max: maximal size of receive buffer allowed for automatically | |
345 | selected receiver buffers for TCP socket. This value does not override | |
53025f5e BF |
346 | net.core.rmem_max. Calling setsockopt() with SO_RCVBUF disables |
347 | automatic tuning of that socket's receive buffer size, in which | |
348 | case this value is ignored. | |
349 | Default: between 87380B and 4MB, depending on RAM size. | |
1da177e4 | 350 | |
ef56e622 SH |
351 | tcp_sack - BOOLEAN |
352 | Enable select acknowledgments (SACKS). | |
1da177e4 | 353 | |
ef56e622 SH |
354 | tcp_slow_start_after_idle - BOOLEAN |
355 | If set, provide RFC2861 behavior and time out the congestion | |
356 | window after an idle period. An idle period is defined at | |
357 | the current RTO. If unset, the congestion window will not | |
358 | be timed out after an idle period. | |
359 | Default: 1 | |
1da177e4 | 360 | |
ef56e622 | 361 | tcp_stdurg - BOOLEAN |
4edc2f34 | 362 | Use the Host requirements interpretation of the TCP urgent pointer field. |
ef56e622 SH |
363 | Most hosts use the older BSD interpretation, so if you turn this on |
364 | Linux might not communicate correctly with them. | |
365 | Default: FALSE | |
1da177e4 | 366 | |
ef56e622 SH |
367 | tcp_synack_retries - INTEGER |
368 | Number of times SYNACKs for a passive TCP connection attempt will | |
369 | be retransmitted. Should not be higher than 255. Default value | |
370 | is 5, which corresponds to ~180seconds. | |
1da177e4 | 371 | |
ef56e622 SH |
372 | tcp_syncookies - BOOLEAN |
373 | Only valid when the kernel was compiled with CONFIG_SYNCOOKIES | |
374 | Send out syncookies when the syn backlog queue of a socket | |
4edc2f34 | 375 | overflows. This is to prevent against the common 'SYN flood attack' |
ef56e622 | 376 | Default: FALSE |
1da177e4 | 377 | |
ef56e622 SH |
378 | Note, that syncookies is fallback facility. |
379 | It MUST NOT be used to help highly loaded servers to stand | |
4edc2f34 | 380 | against legal connection rate. If you see SYN flood warnings |
ef56e622 SH |
381 | in your logs, but investigation shows that they occur |
382 | because of overload with legal connections, you should tune | |
383 | another parameters until this warning disappear. | |
384 | See: tcp_max_syn_backlog, tcp_synack_retries, tcp_abort_on_overflow. | |
1da177e4 | 385 | |
ef56e622 SH |
386 | syncookies seriously violate TCP protocol, do not allow |
387 | to use TCP extensions, can result in serious degradation | |
388 | of some services (f.e. SMTP relaying), visible not by you, | |
389 | but your clients and relays, contacting you. While you see | |
4edc2f34 | 390 | SYN flood warnings in logs not being really flooded, your server |
ef56e622 | 391 | is seriously misconfigured. |
1da177e4 | 392 | |
ef56e622 SH |
393 | tcp_syn_retries - INTEGER |
394 | Number of times initial SYNs for an active TCP connection attempt | |
395 | will be retransmitted. Should not be higher than 255. Default value | |
396 | is 5, which corresponds to ~180seconds. | |
397 | ||
398 | tcp_timestamps - BOOLEAN | |
399 | Enable timestamps as defined in RFC1323. | |
1da177e4 | 400 | |
1da177e4 | 401 | tcp_tso_win_divisor - INTEGER |
ef56e622 SH |
402 | This allows control over what percentage of the congestion window |
403 | can be consumed by a single TSO frame. | |
404 | The setting of this parameter is a choice between burstiness and | |
405 | building larger TSO frames. | |
406 | Default: 3 | |
1da177e4 | 407 | |
ef56e622 SH |
408 | tcp_tw_recycle - BOOLEAN |
409 | Enable fast recycling TIME-WAIT sockets. Default value is 0. | |
410 | It should not be changed without advice/request of technical | |
411 | experts. | |
1da177e4 | 412 | |
ef56e622 SH |
413 | tcp_tw_reuse - BOOLEAN |
414 | Allow to reuse TIME-WAIT sockets for new connections when it is | |
415 | safe from protocol viewpoint. Default value is 0. | |
416 | It should not be changed without advice/request of technical | |
417 | experts. | |
ce7bc3bf | 418 | |
ef56e622 SH |
419 | tcp_window_scaling - BOOLEAN |
420 | Enable window scaling as defined in RFC1323. | |
3ff825b2 | 421 | |
ef56e622 | 422 | tcp_wmem - vector of 3 INTEGERs: min, default, max |
53025f5e | 423 | min: Amount of memory reserved for send buffers for TCP sockets. |
ef56e622 SH |
424 | Each TCP socket has rights to use it due to fact of its birth. |
425 | Default: 4K | |
9d7bcfc6 | 426 | |
53025f5e BF |
427 | default: initial size of send buffer used by TCP sockets. This |
428 | value overrides net.core.wmem_default used by other protocols. | |
429 | It is usually lower than net.core.wmem_default. | |
ef56e622 SH |
430 | Default: 16K |
431 | ||
53025f5e BF |
432 | max: Maximal amount of memory allowed for automatically tuned |
433 | send buffers for TCP sockets. This value does not override | |
434 | net.core.wmem_max. Calling setsockopt() with SO_SNDBUF disables | |
435 | automatic tuning of that socket's send buffer size, in which case | |
436 | this value is ignored. | |
437 | Default: between 64K and 4MB, depending on RAM size. | |
1da177e4 | 438 | |
15d99e02 RJ |
439 | tcp_workaround_signed_windows - BOOLEAN |
440 | If set, assume no receipt of a window scaling option means the | |
441 | remote TCP is broken and treats the window as a signed quantity. | |
442 | If unset, assume the remote TCP is not broken even if we do | |
443 | not receive a window scaling option from them. | |
444 | Default: 0 | |
445 | ||
72d0b7a8 CL |
446 | tcp_dma_copybreak - INTEGER |
447 | Lower limit, in bytes, of the size of socket reads that will be | |
448 | offloaded to a DMA copy engine, if one is present in the system | |
449 | and CONFIG_NET_DMA is enabled. | |
450 | Default: 4096 | |
451 | ||
95766fff HA |
452 | UDP variables: |
453 | ||
454 | udp_mem - vector of 3 INTEGERs: min, pressure, max | |
455 | Number of pages allowed for queueing by all UDP sockets. | |
456 | ||
457 | min: Below this number of pages UDP is not bothered about its | |
458 | memory appetite. When amount of memory allocated by UDP exceeds | |
459 | this number, UDP starts to moderate memory usage. | |
460 | ||
461 | pressure: This value was introduced to follow format of tcp_mem. | |
462 | ||
463 | max: Number of pages allowed for queueing by all UDP sockets. | |
464 | ||
465 | Default is calculated at boot time from amount of available memory. | |
466 | ||
467 | udp_rmem_min - INTEGER | |
468 | Minimal size of receive buffer used by UDP sockets in moderation. | |
469 | Each UDP socket is able to use the size for receiving data, even if | |
470 | total pages of UDP sockets exceed udp_mem pressure. The unit is byte. | |
471 | Default: 4096 | |
472 | ||
473 | udp_wmem_min - INTEGER | |
474 | Minimal size of send buffer used by UDP sockets in moderation. | |
475 | Each UDP socket is able to use the size for sending data, even if | |
476 | total pages of UDP sockets exceed udp_mem pressure. The unit is byte. | |
477 | Default: 4096 | |
478 | ||
8802f616 PM |
479 | CIPSOv4 Variables: |
480 | ||
481 | cipso_cache_enable - BOOLEAN | |
482 | If set, enable additions to and lookups from the CIPSO label mapping | |
483 | cache. If unset, additions are ignored and lookups always result in a | |
484 | miss. However, regardless of the setting the cache is still | |
485 | invalidated when required when means you can safely toggle this on and | |
486 | off and the cache will always be "safe". | |
487 | Default: 1 | |
488 | ||
489 | cipso_cache_bucket_size - INTEGER | |
490 | The CIPSO label cache consists of a fixed size hash table with each | |
491 | hash bucket containing a number of cache entries. This variable limits | |
492 | the number of entries in each hash bucket; the larger the value the | |
493 | more CIPSO label mappings that can be cached. When the number of | |
494 | entries in a given hash bucket reaches this limit adding new entries | |
495 | causes the oldest entry in the bucket to be removed to make room. | |
496 | Default: 10 | |
497 | ||
498 | cipso_rbm_optfmt - BOOLEAN | |
499 | Enable the "Optimized Tag 1 Format" as defined in section 3.4.2.6 of | |
500 | the CIPSO draft specification (see Documentation/netlabel for details). | |
501 | This means that when set the CIPSO tag will be padded with empty | |
502 | categories in order to make the packet data 32-bit aligned. | |
503 | Default: 0 | |
504 | ||
505 | cipso_rbm_structvalid - BOOLEAN | |
506 | If set, do a very strict check of the CIPSO option when | |
507 | ip_options_compile() is called. If unset, relax the checks done during | |
508 | ip_options_compile(). Either way is "safe" as errors are caught else | |
509 | where in the CIPSO processing code but setting this to 0 (False) should | |
510 | result in less work (i.e. it should be faster) but could cause problems | |
511 | with other implementations that require strict checking. | |
512 | Default: 0 | |
513 | ||
1da177e4 LT |
514 | IP Variables: |
515 | ||
516 | ip_local_port_range - 2 INTEGERS | |
517 | Defines the local port range that is used by TCP and UDP to | |
518 | choose the local port. The first number is the first, the | |
519 | second the last local port number. Default value depends on | |
520 | amount of memory available on the system: | |
521 | > 128Mb 32768-61000 | |
522 | < 128Mb 1024-4999 or even less. | |
523 | This number defines number of active connections, which this | |
524 | system can issue simultaneously to systems not supporting | |
525 | TCP extensions (timestamps). With tcp_tw_recycle enabled | |
526 | (i.e. by default) range 1024-4999 is enough to issue up to | |
527 | 2000 connections per second to systems supporting timestamps. | |
528 | ||
529 | ip_nonlocal_bind - BOOLEAN | |
530 | If set, allows processes to bind() to non-local IP addresses, | |
531 | which can be quite useful - but may break some applications. | |
532 | Default: 0 | |
533 | ||
534 | ip_dynaddr - BOOLEAN | |
535 | If set non-zero, enables support for dynamic addresses. | |
536 | If set to a non-zero value larger than 1, a kernel log | |
537 | message will be printed when dynamic address rewriting | |
538 | occurs. | |
539 | Default: 0 | |
540 | ||
541 | icmp_echo_ignore_all - BOOLEAN | |
7ce31246 DM |
542 | If set non-zero, then the kernel will ignore all ICMP ECHO |
543 | requests sent to it. | |
544 | Default: 0 | |
545 | ||
1da177e4 | 546 | icmp_echo_ignore_broadcasts - BOOLEAN |
7ce31246 DM |
547 | If set non-zero, then the kernel will ignore all ICMP ECHO and |
548 | TIMESTAMP requests sent to it via broadcast/multicast. | |
549 | Default: 1 | |
1da177e4 LT |
550 | |
551 | icmp_ratelimit - INTEGER | |
552 | Limit the maximal rates for sending ICMP packets whose type matches | |
553 | icmp_ratemask (see below) to specific targets. | |
6dbf4bca SH |
554 | 0 to disable any limiting, |
555 | otherwise the minimal space between responses in milliseconds. | |
556 | Default: 1000 | |
1da177e4 LT |
557 | |
558 | icmp_ratemask - INTEGER | |
559 | Mask made of ICMP types for which rates are being limited. | |
560 | Significant bits: IHGFEDCBA9876543210 | |
561 | Default mask: 0000001100000011000 (6168) | |
562 | ||
563 | Bit definitions (see include/linux/icmp.h): | |
564 | 0 Echo Reply | |
565 | 3 Destination Unreachable * | |
566 | 4 Source Quench * | |
567 | 5 Redirect | |
568 | 8 Echo Request | |
569 | B Time Exceeded * | |
570 | C Parameter Problem * | |
571 | D Timestamp Request | |
572 | E Timestamp Reply | |
573 | F Info Request | |
574 | G Info Reply | |
575 | H Address Mask Request | |
576 | I Address Mask Reply | |
577 | ||
578 | * These are rate limited by default (see default mask above) | |
579 | ||
580 | icmp_ignore_bogus_error_responses - BOOLEAN | |
581 | Some routers violate RFC1122 by sending bogus responses to broadcast | |
582 | frames. Such violations are normally logged via a kernel warning. | |
583 | If this is set to TRUE, the kernel will not give such warnings, which | |
584 | will avoid log file clutter. | |
585 | Default: FALSE | |
586 | ||
95f7daf1 H |
587 | icmp_errors_use_inbound_ifaddr - BOOLEAN |
588 | ||
589 | If zero, icmp error messages are sent with the primary address of | |
590 | the exiting interface. | |
591 | ||
592 | If non-zero, the message will be sent with the primary address of | |
593 | the interface that received the packet that caused the icmp error. | |
594 | This is the behaviour network many administrators will expect from | |
595 | a router. And it can make debugging complicated network layouts | |
596 | much easier. | |
597 | ||
598 | Note that if no primary address exists for the interface selected, | |
599 | then the primary address of the first non-loopback interface that | |
d6bc8ac9 | 600 | has one will be used regardless of this setting. |
95f7daf1 H |
601 | |
602 | Default: 0 | |
603 | ||
1da177e4 LT |
604 | igmp_max_memberships - INTEGER |
605 | Change the maximum number of multicast groups we can subscribe to. | |
606 | Default: 20 | |
607 | ||
608 | conf/interface/* changes special settings per interface (where "interface" is | |
609 | the name of your network interface) | |
610 | conf/all/* is special, changes the settings for all interfaces | |
611 | ||
612 | ||
613 | log_martians - BOOLEAN | |
614 | Log packets with impossible addresses to kernel log. | |
615 | log_martians for the interface will be enabled if at least one of | |
616 | conf/{all,interface}/log_martians is set to TRUE, | |
617 | it will be disabled otherwise | |
618 | ||
619 | accept_redirects - BOOLEAN | |
620 | Accept ICMP redirect messages. | |
621 | accept_redirects for the interface will be enabled if: | |
622 | - both conf/{all,interface}/accept_redirects are TRUE in the case forwarding | |
623 | for the interface is enabled | |
624 | or | |
625 | - at least one of conf/{all,interface}/accept_redirects is TRUE in the case | |
626 | forwarding for the interface is disabled | |
627 | accept_redirects for the interface will be disabled otherwise | |
628 | default TRUE (host) | |
629 | FALSE (router) | |
630 | ||
631 | forwarding - BOOLEAN | |
632 | Enable IP forwarding on this interface. | |
633 | ||
634 | mc_forwarding - BOOLEAN | |
635 | Do multicast routing. The kernel needs to be compiled with CONFIG_MROUTE | |
636 | and a multicast routing daemon is required. | |
637 | conf/all/mc_forwarding must also be set to TRUE to enable multicast routing | |
638 | for the interface | |
639 | ||
640 | medium_id - INTEGER | |
641 | Integer value used to differentiate the devices by the medium they | |
642 | are attached to. Two devices can have different id values when | |
643 | the broadcast packets are received only on one of them. | |
644 | The default value 0 means that the device is the only interface | |
645 | to its medium, value of -1 means that medium is not known. | |
646 | ||
647 | Currently, it is used to change the proxy_arp behavior: | |
648 | the proxy_arp feature is enabled for packets forwarded between | |
649 | two devices attached to different media. | |
650 | ||
651 | proxy_arp - BOOLEAN | |
652 | Do proxy arp. | |
653 | proxy_arp for the interface will be enabled if at least one of | |
654 | conf/{all,interface}/proxy_arp is set to TRUE, | |
655 | it will be disabled otherwise | |
656 | ||
657 | shared_media - BOOLEAN | |
658 | Send(router) or accept(host) RFC1620 shared media redirects. | |
659 | Overrides ip_secure_redirects. | |
660 | shared_media for the interface will be enabled if at least one of | |
661 | conf/{all,interface}/shared_media is set to TRUE, | |
662 | it will be disabled otherwise | |
663 | default TRUE | |
664 | ||
665 | secure_redirects - BOOLEAN | |
666 | Accept ICMP redirect messages only for gateways, | |
667 | listed in default gateway list. | |
668 | secure_redirects for the interface will be enabled if at least one of | |
669 | conf/{all,interface}/secure_redirects is set to TRUE, | |
670 | it will be disabled otherwise | |
671 | default TRUE | |
672 | ||
673 | send_redirects - BOOLEAN | |
674 | Send redirects, if router. | |
675 | send_redirects for the interface will be enabled if at least one of | |
676 | conf/{all,interface}/send_redirects is set to TRUE, | |
677 | it will be disabled otherwise | |
678 | Default: TRUE | |
679 | ||
680 | bootp_relay - BOOLEAN | |
681 | Accept packets with source address 0.b.c.d destined | |
682 | not to this host as local ones. It is supposed, that | |
683 | BOOTP relay daemon will catch and forward such packets. | |
684 | conf/all/bootp_relay must also be set to TRUE to enable BOOTP relay | |
685 | for the interface | |
686 | default FALSE | |
687 | Not Implemented Yet. | |
688 | ||
689 | accept_source_route - BOOLEAN | |
690 | Accept packets with SRR option. | |
691 | conf/all/accept_source_route must also be set to TRUE to accept packets | |
692 | with SRR option on the interface | |
693 | default TRUE (router) | |
694 | FALSE (host) | |
695 | ||
696 | rp_filter - BOOLEAN | |
697 | 1 - do source validation by reversed path, as specified in RFC1812 | |
698 | Recommended option for single homed hosts and stub network | |
699 | routers. Could cause troubles for complicated (not loop free) | |
700 | networks running a slow unreliable protocol (sort of RIP), | |
701 | or using static routes. | |
702 | ||
703 | 0 - No source validation. | |
704 | ||
705 | conf/all/rp_filter must also be set to TRUE to do source validation | |
706 | on the interface | |
707 | ||
708 | Default value is 0. Note that some distributions enable it | |
709 | in startup scripts. | |
710 | ||
711 | arp_filter - BOOLEAN | |
712 | 1 - Allows you to have multiple network interfaces on the same | |
713 | subnet, and have the ARPs for each interface be answered | |
714 | based on whether or not the kernel would route a packet from | |
715 | the ARP'd IP out that interface (therefore you must use source | |
716 | based routing for this to work). In other words it allows control | |
717 | of which cards (usually 1) will respond to an arp request. | |
718 | ||
719 | 0 - (default) The kernel can respond to arp requests with addresses | |
720 | from other interfaces. This may seem wrong but it usually makes | |
721 | sense, because it increases the chance of successful communication. | |
722 | IP addresses are owned by the complete host on Linux, not by | |
723 | particular interfaces. Only for more complex setups like load- | |
724 | balancing, does this behaviour cause problems. | |
725 | ||
726 | arp_filter for the interface will be enabled if at least one of | |
727 | conf/{all,interface}/arp_filter is set to TRUE, | |
728 | it will be disabled otherwise | |
729 | ||
730 | arp_announce - INTEGER | |
731 | Define different restriction levels for announcing the local | |
732 | source IP address from IP packets in ARP requests sent on | |
733 | interface: | |
734 | 0 - (default) Use any local address, configured on any interface | |
735 | 1 - Try to avoid local addresses that are not in the target's | |
736 | subnet for this interface. This mode is useful when target | |
737 | hosts reachable via this interface require the source IP | |
738 | address in ARP requests to be part of their logical network | |
739 | configured on the receiving interface. When we generate the | |
740 | request we will check all our subnets that include the | |
741 | target IP and will preserve the source address if it is from | |
742 | such subnet. If there is no such subnet we select source | |
743 | address according to the rules for level 2. | |
744 | 2 - Always use the best local address for this target. | |
745 | In this mode we ignore the source address in the IP packet | |
746 | and try to select local address that we prefer for talks with | |
747 | the target host. Such local address is selected by looking | |
748 | for primary IP addresses on all our subnets on the outgoing | |
749 | interface that include the target IP address. If no suitable | |
750 | local address is found we select the first local address | |
751 | we have on the outgoing interface or on all other interfaces, | |
752 | with the hope we will receive reply for our request and | |
753 | even sometimes no matter the source IP address we announce. | |
754 | ||
755 | The max value from conf/{all,interface}/arp_announce is used. | |
756 | ||
757 | Increasing the restriction level gives more chance for | |
758 | receiving answer from the resolved target while decreasing | |
759 | the level announces more valid sender's information. | |
760 | ||
761 | arp_ignore - INTEGER | |
762 | Define different modes for sending replies in response to | |
763 | received ARP requests that resolve local target IP addresses: | |
764 | 0 - (default): reply for any local target IP address, configured | |
765 | on any interface | |
766 | 1 - reply only if the target IP address is local address | |
767 | configured on the incoming interface | |
768 | 2 - reply only if the target IP address is local address | |
769 | configured on the incoming interface and both with the | |
770 | sender's IP address are part from same subnet on this interface | |
771 | 3 - do not reply for local addresses configured with scope host, | |
772 | only resolutions for global and link addresses are replied | |
773 | 4-7 - reserved | |
774 | 8 - do not reply for all local addresses | |
775 | ||
776 | The max value from conf/{all,interface}/arp_ignore is used | |
777 | when ARP request is received on the {interface} | |
778 | ||
c1b1bce8 NH |
779 | arp_accept - BOOLEAN |
780 | Define behavior when gratuitous arp replies are received: | |
781 | 0 - drop gratuitous arp frames | |
782 | 1 - accept gratuitous arp frames | |
783 | ||
1da177e4 LT |
784 | app_solicit - INTEGER |
785 | The maximum number of probes to send to the user space ARP daemon | |
786 | via netlink before dropping back to multicast probes (see | |
787 | mcast_solicit). Defaults to 0. | |
788 | ||
789 | disable_policy - BOOLEAN | |
790 | Disable IPSEC policy (SPD) for this interface | |
791 | ||
792 | disable_xfrm - BOOLEAN | |
793 | Disable IPSEC encryption on this interface, whatever the policy | |
794 | ||
795 | ||
796 | ||
797 | tag - INTEGER | |
798 | Allows you to write a number, which can be used as required. | |
799 | Default value is 0. | |
800 | ||
1da177e4 LT |
801 | Alexey Kuznetsov. |
802 | kuznet@ms2.inr.ac.ru | |
803 | ||
804 | Updated by: | |
805 | Andi Kleen | |
806 | ak@muc.de | |
807 | Nicolas Delon | |
808 | delon.nicolas@wanadoo.fr | |
809 | ||
810 | ||
811 | ||
812 | ||
813 | /proc/sys/net/ipv6/* Variables: | |
814 | ||
815 | IPv6 has no global variables such as tcp_*. tcp_* settings under ipv4/ also | |
816 | apply to IPv6 [XXX?]. | |
817 | ||
818 | bindv6only - BOOLEAN | |
819 | Default value for IPV6_V6ONLY socket option, | |
820 | which restricts use of the IPv6 socket to IPv6 communication | |
821 | only. | |
822 | TRUE: disable IPv4-mapped address feature | |
823 | FALSE: enable IPv4-mapped address feature | |
824 | ||
825 | Default: FALSE (as specified in RFC2553bis) | |
826 | ||
827 | IPv6 Fragmentation: | |
828 | ||
829 | ip6frag_high_thresh - INTEGER | |
830 | Maximum memory used to reassemble IPv6 fragments. When | |
831 | ip6frag_high_thresh bytes of memory is allocated for this purpose, | |
832 | the fragment handler will toss packets until ip6frag_low_thresh | |
833 | is reached. | |
834 | ||
835 | ip6frag_low_thresh - INTEGER | |
836 | See ip6frag_high_thresh | |
837 | ||
838 | ip6frag_time - INTEGER | |
839 | Time in seconds to keep an IPv6 fragment in memory. | |
840 | ||
841 | ip6frag_secret_interval - INTEGER | |
842 | Regeneration interval (in seconds) of the hash secret (or lifetime | |
843 | for the hash secret) for IPv6 fragments. | |
844 | Default: 600 | |
845 | ||
846 | conf/default/*: | |
847 | Change the interface-specific default settings. | |
848 | ||
849 | ||
850 | conf/all/*: | |
851 | Change all the interface-specific settings. | |
852 | ||
853 | [XXX: Other special features than forwarding?] | |
854 | ||
855 | conf/all/forwarding - BOOLEAN | |
856 | Enable global IPv6 forwarding between all interfaces. | |
857 | ||
858 | IPv4 and IPv6 work differently here; e.g. netfilter must be used | |
859 | to control which interfaces may forward packets and which not. | |
860 | ||
861 | This also sets all interfaces' Host/Router setting | |
862 | 'forwarding' to the specified value. See below for details. | |
863 | ||
864 | This referred to as global forwarding. | |
865 | ||
fbea49e1 YH |
866 | proxy_ndp - BOOLEAN |
867 | Do proxy ndp. | |
868 | ||
1da177e4 LT |
869 | conf/interface/*: |
870 | Change special settings per interface. | |
871 | ||
872 | The functional behaviour for certain settings is different | |
873 | depending on whether local forwarding is enabled or not. | |
874 | ||
875 | accept_ra - BOOLEAN | |
876 | Accept Router Advertisements; autoconfigure using them. | |
877 | ||
878 | Functional default: enabled if local forwarding is disabled. | |
879 | disabled if local forwarding is enabled. | |
880 | ||
65f5c7c1 YH |
881 | accept_ra_defrtr - BOOLEAN |
882 | Learn default router in Router Advertisement. | |
883 | ||
884 | Functional default: enabled if accept_ra is enabled. | |
885 | disabled if accept_ra is disabled. | |
886 | ||
c4fd30eb | 887 | accept_ra_pinfo - BOOLEAN |
2fe0ae78 | 888 | Learn Prefix Information in Router Advertisement. |
c4fd30eb YH |
889 | |
890 | Functional default: enabled if accept_ra is enabled. | |
891 | disabled if accept_ra is disabled. | |
892 | ||
09c884d4 YH |
893 | accept_ra_rt_info_max_plen - INTEGER |
894 | Maximum prefix length of Route Information in RA. | |
895 | ||
896 | Route Information w/ prefix larger than or equal to this | |
897 | variable shall be ignored. | |
898 | ||
899 | Functional default: 0 if accept_ra_rtr_pref is enabled. | |
900 | -1 if accept_ra_rtr_pref is disabled. | |
901 | ||
930d6ff2 YH |
902 | accept_ra_rtr_pref - BOOLEAN |
903 | Accept Router Preference in RA. | |
904 | ||
905 | Functional default: enabled if accept_ra is enabled. | |
906 | disabled if accept_ra is disabled. | |
907 | ||
1da177e4 LT |
908 | accept_redirects - BOOLEAN |
909 | Accept Redirects. | |
910 | ||
911 | Functional default: enabled if local forwarding is disabled. | |
912 | disabled if local forwarding is enabled. | |
913 | ||
0bcbc926 YH |
914 | accept_source_route - INTEGER |
915 | Accept source routing (routing extension header). | |
916 | ||
bb4dbf9e | 917 | >= 0: Accept only routing header type 2. |
0bcbc926 YH |
918 | < 0: Do not accept routing header. |
919 | ||
920 | Default: 0 | |
921 | ||
1da177e4 LT |
922 | autoconf - BOOLEAN |
923 | Autoconfigure addresses using Prefix Information in Router | |
924 | Advertisements. | |
925 | ||
c4fd30eb YH |
926 | Functional default: enabled if accept_ra_pinfo is enabled. |
927 | disabled if accept_ra_pinfo is disabled. | |
1da177e4 LT |
928 | |
929 | dad_transmits - INTEGER | |
930 | The amount of Duplicate Address Detection probes to send. | |
931 | Default: 1 | |
932 | ||
933 | forwarding - BOOLEAN | |
934 | Configure interface-specific Host/Router behaviour. | |
935 | ||
936 | Note: It is recommended to have the same setting on all | |
937 | interfaces; mixed router/host scenarios are rather uncommon. | |
938 | ||
939 | FALSE: | |
940 | ||
941 | By default, Host behaviour is assumed. This means: | |
942 | ||
943 | 1. IsRouter flag is not set in Neighbour Advertisements. | |
944 | 2. Router Solicitations are being sent when necessary. | |
945 | 3. If accept_ra is TRUE (default), accept Router | |
946 | Advertisements (and do autoconfiguration). | |
947 | 4. If accept_redirects is TRUE (default), accept Redirects. | |
948 | ||
949 | TRUE: | |
950 | ||
951 | If local forwarding is enabled, Router behaviour is assumed. | |
952 | This means exactly the reverse from the above: | |
953 | ||
954 | 1. IsRouter flag is set in Neighbour Advertisements. | |
955 | 2. Router Solicitations are not sent. | |
956 | 3. Router Advertisements are ignored. | |
957 | 4. Redirects are ignored. | |
958 | ||
959 | Default: FALSE if global forwarding is disabled (default), | |
960 | otherwise TRUE. | |
961 | ||
962 | hop_limit - INTEGER | |
963 | Default Hop Limit to set. | |
964 | Default: 64 | |
965 | ||
966 | mtu - INTEGER | |
967 | Default Maximum Transfer Unit | |
968 | Default: 1280 (IPv6 required minimum) | |
969 | ||
52e16356 YH |
970 | router_probe_interval - INTEGER |
971 | Minimum interval (in seconds) between Router Probing described | |
972 | in RFC4191. | |
973 | ||
974 | Default: 60 | |
975 | ||
1da177e4 LT |
976 | router_solicitation_delay - INTEGER |
977 | Number of seconds to wait after interface is brought up | |
978 | before sending Router Solicitations. | |
979 | Default: 1 | |
980 | ||
981 | router_solicitation_interval - INTEGER | |
982 | Number of seconds to wait between Router Solicitations. | |
983 | Default: 4 | |
984 | ||
985 | router_solicitations - INTEGER | |
986 | Number of Router Solicitations to send until assuming no | |
987 | routers are present. | |
988 | Default: 3 | |
989 | ||
990 | use_tempaddr - INTEGER | |
991 | Preference for Privacy Extensions (RFC3041). | |
992 | <= 0 : disable Privacy Extensions | |
993 | == 1 : enable Privacy Extensions, but prefer public | |
994 | addresses over temporary addresses. | |
995 | > 1 : enable Privacy Extensions and prefer temporary | |
996 | addresses over public addresses. | |
997 | Default: 0 (for most devices) | |
998 | -1 (for point-to-point devices and loopback devices) | |
999 | ||
1000 | temp_valid_lft - INTEGER | |
1001 | valid lifetime (in seconds) for temporary addresses. | |
1002 | Default: 604800 (7 days) | |
1003 | ||
1004 | temp_prefered_lft - INTEGER | |
1005 | Preferred lifetime (in seconds) for temporary addresses. | |
1006 | Default: 86400 (1 day) | |
1007 | ||
1008 | max_desync_factor - INTEGER | |
1009 | Maximum value for DESYNC_FACTOR, which is a random value | |
1010 | that ensures that clients don't synchronize with each | |
1011 | other and generate new addresses at exactly the same time. | |
1012 | value is in seconds. | |
1013 | Default: 600 | |
1014 | ||
1015 | regen_max_retry - INTEGER | |
1016 | Number of attempts before give up attempting to generate | |
1017 | valid temporary addresses. | |
1018 | Default: 5 | |
1019 | ||
1020 | max_addresses - INTEGER | |
1021 | Number of maximum addresses per interface. 0 disables limitation. | |
1022 | It is recommended not set too large value (or 0) because it would | |
1023 | be too easy way to crash kernel to allow to create too much of | |
1024 | autoconfigured addresses. | |
1025 | Default: 16 | |
1026 | ||
778d80be YH |
1027 | disable_ipv6 - BOOLEAN |
1028 | Disable IPv6 operation. | |
1029 | Default: FALSE (enable IPv6 operation) | |
1030 | ||
1b34be74 YH |
1031 | accept_dad - INTEGER |
1032 | Whether to accept DAD (Duplicate Address Detection). | |
1033 | 0: Disable DAD | |
1034 | 1: Enable DAD (default) | |
1035 | 2: Enable DAD, and disable IPv6 operation if MAC-based duplicate | |
1036 | link-local address has been found. | |
1037 | ||
1da177e4 LT |
1038 | icmp/*: |
1039 | ratelimit - INTEGER | |
1040 | Limit the maximal rates for sending ICMPv6 packets. | |
6dbf4bca SH |
1041 | 0 to disable any limiting, |
1042 | otherwise the minimal space between responses in milliseconds. | |
1043 | Default: 1000 | |
1da177e4 LT |
1044 | |
1045 | ||
1046 | IPv6 Update by: | |
1047 | Pekka Savola <pekkas@netcore.fi> | |
1048 | YOSHIFUJI Hideaki / USAGI Project <yoshfuji@linux-ipv6.org> | |
1049 | ||
1050 | ||
1051 | /proc/sys/net/bridge/* Variables: | |
1052 | ||
1053 | bridge-nf-call-arptables - BOOLEAN | |
1054 | 1 : pass bridged ARP traffic to arptables' FORWARD chain. | |
1055 | 0 : disable this. | |
1056 | Default: 1 | |
1057 | ||
1058 | bridge-nf-call-iptables - BOOLEAN | |
1059 | 1 : pass bridged IPv4 traffic to iptables' chains. | |
1060 | 0 : disable this. | |
1061 | Default: 1 | |
1062 | ||
1063 | bridge-nf-call-ip6tables - BOOLEAN | |
1064 | 1 : pass bridged IPv6 traffic to ip6tables' chains. | |
1065 | 0 : disable this. | |
1066 | Default: 1 | |
1067 | ||
1068 | bridge-nf-filter-vlan-tagged - BOOLEAN | |
516299d2 MM |
1069 | 1 : pass bridged vlan-tagged ARP/IP/IPv6 traffic to {arp,ip,ip6}tables. |
1070 | 0 : disable this. | |
1071 | Default: 1 | |
1072 | ||
1073 | bridge-nf-filter-pppoe-tagged - BOOLEAN | |
1074 | 1 : pass bridged pppoe-tagged IP/IPv6 traffic to {ip,ip6}tables. | |
1da177e4 LT |
1075 | 0 : disable this. |
1076 | Default: 1 | |
1077 | ||
1078 | ||
32e8d494 VY |
1079 | proc/sys/net/sctp/* Variables: |
1080 | ||
1081 | addip_enable - BOOLEAN | |
1082 | Enable or disable extension of Dynamic Address Reconfiguration | |
1083 | (ADD-IP) functionality specified in RFC5061. This extension provides | |
1084 | the ability to dynamically add and remove new addresses for the SCTP | |
1085 | associations. | |
1086 | ||
1087 | 1: Enable extension. | |
1088 | ||
1089 | 0: Disable extension. | |
1090 | ||
1091 | Default: 0 | |
1092 | ||
1093 | addip_noauth_enable - BOOLEAN | |
1094 | Dynamic Address Reconfiguration (ADD-IP) requires the use of | |
1095 | authentication to protect the operations of adding or removing new | |
1096 | addresses. This requirement is mandated so that unauthorized hosts | |
1097 | would not be able to hijack associations. However, older | |
1098 | implementations may not have implemented this requirement while | |
1099 | allowing the ADD-IP extension. For reasons of interoperability, | |
1100 | we provide this variable to control the enforcement of the | |
1101 | authentication requirement. | |
1102 | ||
1103 | 1: Allow ADD-IP extension to be used without authentication. This | |
1104 | should only be set in a closed environment for interoperability | |
1105 | with older implementations. | |
1106 | ||
1107 | 0: Enforce the authentication requirement | |
1108 | ||
1109 | Default: 0 | |
1110 | ||
1111 | auth_enable - BOOLEAN | |
1112 | Enable or disable Authenticated Chunks extension. This extension | |
1113 | provides the ability to send and receive authenticated chunks and is | |
1114 | required for secure operation of Dynamic Address Reconfiguration | |
1115 | (ADD-IP) extension. | |
1116 | ||
1117 | 1: Enable this extension. | |
1118 | 0: Disable this extension. | |
1119 | ||
1120 | Default: 0 | |
1121 | ||
1122 | prsctp_enable - BOOLEAN | |
1123 | Enable or disable the Partial Reliability extension (RFC3758) which | |
1124 | is used to notify peers that a given DATA should no longer be expected. | |
1125 | ||
1126 | 1: Enable extension | |
1127 | 0: Disable | |
1128 | ||
1129 | Default: 1 | |
1130 | ||
1131 | max_burst - INTEGER | |
1132 | The limit of the number of new packets that can be initially sent. It | |
1133 | controls how bursty the generated traffic can be. | |
1134 | ||
1135 | Default: 4 | |
1136 | ||
1137 | association_max_retrans - INTEGER | |
1138 | Set the maximum number for retransmissions that an association can | |
1139 | attempt deciding that the remote end is unreachable. If this value | |
1140 | is exceeded, the association is terminated. | |
1141 | ||
1142 | Default: 10 | |
1143 | ||
1144 | max_init_retransmits - INTEGER | |
1145 | The maximum number of retransmissions of INIT and COOKIE-ECHO chunks | |
1146 | that an association will attempt before declaring the destination | |
1147 | unreachable and terminating. | |
1148 | ||
1149 | Default: 8 | |
1150 | ||
1151 | path_max_retrans - INTEGER | |
1152 | The maximum number of retransmissions that will be attempted on a given | |
1153 | path. Once this threshold is exceeded, the path is considered | |
1154 | unreachable, and new traffic will use a different path when the | |
1155 | association is multihomed. | |
1156 | ||
1157 | Default: 5 | |
1158 | ||
1159 | rto_initial - INTEGER | |
1160 | The initial round trip timeout value in milliseconds that will be used | |
1161 | in calculating round trip times. This is the initial time interval | |
1162 | for retransmissions. | |
1163 | ||
1164 | Default: 3000 | |
1da177e4 | 1165 | |
32e8d494 VY |
1166 | rto_max - INTEGER |
1167 | The maximum value (in milliseconds) of the round trip timeout. This | |
1168 | is the largest time interval that can elapse between retransmissions. | |
1169 | ||
1170 | Default: 60000 | |
1171 | ||
1172 | rto_min - INTEGER | |
1173 | The minimum value (in milliseconds) of the round trip timeout. This | |
1174 | is the smallest time interval the can elapse between retransmissions. | |
1175 | ||
1176 | Default: 1000 | |
1177 | ||
1178 | hb_interval - INTEGER | |
1179 | The interval (in milliseconds) between HEARTBEAT chunks. These chunks | |
1180 | are sent at the specified interval on idle paths to probe the state of | |
1181 | a given path between 2 associations. | |
1182 | ||
1183 | Default: 30000 | |
1184 | ||
1185 | sack_timeout - INTEGER | |
1186 | The amount of time (in milliseconds) that the implementation will wait | |
1187 | to send a SACK. | |
1188 | ||
1189 | Default: 200 | |
1190 | ||
1191 | valid_cookie_life - INTEGER | |
1192 | The default lifetime of the SCTP cookie (in milliseconds). The cookie | |
1193 | is used during association establishment. | |
1194 | ||
1195 | Default: 60000 | |
1196 | ||
1197 | cookie_preserve_enable - BOOLEAN | |
1198 | Enable or disable the ability to extend the lifetime of the SCTP cookie | |
1199 | that is used during the establishment phase of SCTP association | |
1200 | ||
1201 | 1: Enable cookie lifetime extension. | |
1202 | 0: Disable | |
1203 | ||
1204 | Default: 1 | |
1205 | ||
1206 | rcvbuf_policy - INTEGER | |
1207 | Determines if the receive buffer is attributed to the socket or to | |
1208 | association. SCTP supports the capability to create multiple | |
1209 | associations on a single socket. When using this capability, it is | |
1210 | possible that a single stalled association that's buffering a lot | |
1211 | of data may block other associations from delivering their data by | |
1212 | consuming all of the receive buffer space. To work around this, | |
1213 | the rcvbuf_policy could be set to attribute the receiver buffer space | |
1214 | to each association instead of the socket. This prevents the described | |
1215 | blocking. | |
1216 | ||
1217 | 1: rcvbuf space is per association | |
1218 | 0: recbuf space is per socket | |
1219 | ||
1220 | Default: 0 | |
1221 | ||
1222 | sndbuf_policy - INTEGER | |
1223 | Similar to rcvbuf_policy above, this applies to send buffer space. | |
1224 | ||
1225 | 1: Send buffer is tracked per association | |
1226 | 0: Send buffer is tracked per socket. | |
1227 | ||
1228 | Default: 0 | |
1229 | ||
1230 | sctp_mem - vector of 3 INTEGERs: min, pressure, max | |
1231 | Number of pages allowed for queueing by all SCTP sockets. | |
1232 | ||
1233 | min: Below this number of pages SCTP is not bothered about its | |
1234 | memory appetite. When amount of memory allocated by SCTP exceeds | |
1235 | this number, SCTP starts to moderate memory usage. | |
1236 | ||
1237 | pressure: This value was introduced to follow format of tcp_mem. | |
1238 | ||
1239 | max: Number of pages allowed for queueing by all SCTP sockets. | |
1240 | ||
1241 | Default is calculated at boot time from amount of available memory. | |
1242 | ||
1243 | sctp_rmem - vector of 3 INTEGERs: min, default, max | |
1244 | See tcp_rmem for a description. | |
1245 | ||
1246 | sctp_wmem - vector of 3 INTEGERs: min, default, max | |
1247 | See tcp_wmem for a description. | |
1248 | ||
1da177e4 | 1249 | UNDOCUMENTED: |
1da177e4 | 1250 | |
4edc2f34 SH |
1251 | /proc/sys/net/core/* |
1252 | dev_weight FIXME | |
1253 | ||
1254 | /proc/sys/net/unix/* | |
1255 | max_dgram_qlen FIXME | |
1256 | ||
1257 | /proc/sys/net/irda/* | |
1258 | fast_poll_increase FIXME | |
1259 | warn_noreply_time FIXME | |
1260 | discovery_slots FIXME | |
1261 | slot_timeout FIXME | |
1262 | max_baud_rate FIXME | |
1263 | discovery_timeout FIXME | |
1264 | lap_keepalive_time FIXME | |
1265 | max_noreply_time FIXME | |
1266 | max_tx_data_size FIXME | |
1267 | max_tx_window FIXME | |
1268 | min_tx_turn_time FIXME |