projects / deliverable / linux.git / blame
| Commit | Line | Data |
|---|---|---|
| 1f5e6c63 SH |
1 | /dts-v1/; |
| 2 | ||
| 3 | /include/ "dove.dtsi" | |
| 4 | ||
| 5 | / { | |
| 6 | model = "SolidRun CuBox"; | |
| 7 | compatible = "solidrun,cubox", "marvell,dove"; | |
| 8 | ||
| 9 | memory { | |
| 10 | device_type = "memory"; | |
| 11 | reg = <0x00000000 0x40000000>; | |
| 12 | }; | |
| 13 | ||
| 14 | chosen { | |
| 15 | bootargs = "console=ttyS0,115200n8 earlyprintk"; | |
| 16 | }; | |
| 17 | ||
| 18 | leds { | |
| 19 | compatible = "gpio-leds"; | |
| e35e40cd SH |
20 | pinctrl-0 = <&pmx_gpio_18>; |
| 21 | pinctrl-names = "default"; | |
| 22 | ||
| 1f5e6c63 SH |
23 | power { |
| 24 | label = "Power"; | |
| 25 | gpios = <&gpio0 18 1>; | |
| 26 | linux,default-trigger = "default-on"; | |
| 27 | }; | |
| 28 | }; | |
| 41e364bb SH |
29 | |
| 30 | regulators { | |
| 31 | compatible = "simple-bus"; | |
| 32 | #address-cells = <1>; | |
| 33 | #size-cells = <0>; | |
| 34 | ||
| 35 | usb_power: regulator@1 { | |
| 36 | compatible = "regulator-fixed"; | |
| 37 | reg = <1>; | |
| 38 | regulator-name = "USB Power"; | |
| 39 | regulator-min-microvolt = <5000000>; | |
| 40 | regulator-max-microvolt = <5000000>; | |
| 41 | enable-active-high; | |
| 42 | regulator-always-on; | |
| 43 | regulator-boot-on; | |
| 44 | gpio = <&gpio0 1 0>; | |
| 535fb344 SH |
45 | pinctrl-0 = <&pmx_gpio_1>; |
| 46 | pinctrl-names = "default"; | |
| 41e364bb SH |
47 | }; |
| 48 | }; | |
| 53e9cb1d SH |
49 | |
| 50 | clocks { | |
| 51 | /* 25MHz reference crystal */ | |
| 52 | ref25: oscillator { | |
| 53 | compatible = "fixed-clock"; | |
| 54 | #clock-cells = <0>; | |
| 55 | clock-frequency = <25000000>; | |
| 56 | }; | |
| 57 | }; | |
| 1f5e6c63 SH |
58 | }; |
| 59 | ||
| 60 | &uart0 { status = "okay"; }; | |
| 1f5e6c63 | 61 | &sata0 { status = "okay"; }; |
| 4c3f6b86 SH |
62 | &mdio { status = "okay"; }; |
| 63 | ð { status = "okay"; }; | |
| 64 | ||
| 65 | ðphy { | |
| 66 | compatible = "marvell,88e1310"; | |
| 67 | reg = <1>; | |
| 68 | }; | |
| 53e9cb1d SH |
69 | |
| 70 | &i2c0 { | |
| 71 | status = "okay"; | |
| 72 | clock-frequency = <100000>; | |
| 73 | ||
| 74 | si5351: clock-generator { | |
| 75 | compatible = "silabs,si5351a-msop"; | |
| 76 | reg = <0x60>; | |
| 77 | #address-cells = <1>; | |
| 78 | #size-cells = <0>; | |
| 79 | #clock-cells = <1>; | |
| 80 | ||
| 81 | /* connect xtal input to 25MHz reference */ | |
| 82 | clocks = <&ref25>; | |
| 83 | ||
| 84 | /* connect xtal input as source of pll0 and pll1 */ | |
| 85 | silabs,pll-source = <0 0>, <1 0>; | |
| 86 | ||
| 87 | clkout0 { | |
| 88 | reg = <0>; | |
| 89 | silabs,drive-strength = <8>; | |
| 90 | silabs,multisynth-source = <0>; | |
| 91 | silabs,clock-source = <0>; | |
| 92 | silabs,pll-master; | |
| 93 | }; | |
| 94 | ||
| 95 | clkout1 { | |
| 96 | reg = <1>; | |
| 97 | silabs,drive-strength = <8>; | |
| 98 | silabs,multisynth-source = <1>; | |
| 99 | silabs,clock-source = <0>; | |
| 100 | silabs,pll-master; | |
| 101 | }; | |
| 102 | ||
| 103 | clkout2 { | |
| 104 | reg = <2>; | |
| 105 | silabs,multisynth-source = <1>; | |
| 106 | silabs,clock-source = <0>; | |
| 107 | }; | |
| 108 | }; | |
| 109 | }; | |
| 1f5e6c63 | 110 | |
| 9e1c96ed SH |
111 | &sdio0 { |
| 112 | status = "okay"; | |
| 113 | /* sdio0 card detect is connected to wrong pin on CuBox */ | |
| 114 | cd-gpios = <&gpio0 12 1>; | |
| 535fb344 | 115 | pinctrl-0 = <&pmx_sdio0 &pmx_gpio_12>; |
| 9e1c96ed SH |
116 | }; |
| 117 | ||
| 1f5e6c63 SH |
118 | &spi0 { |
| 119 | status = "okay"; | |
| 120 | ||
| 121 | /* spi0.0: 4M Flash Winbond W25Q32BV */ | |
| 122 | spi-flash@0 { | |
| 123 | compatible = "st,w25q32"; | |
| 124 | spi-max-frequency = <20000000>; | |
| 125 | reg = <0>; | |
| 126 | }; | |
| 127 | }; |