Commit | Line | Data |
---|---|---|
ee9a97db TL |
1 | /* |
2 | * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/ | |
3 | * | |
4 | * This program is free software; you can redistribute it and/or modify | |
5 | * it under the terms of the GNU General Public License version 2 as | |
6 | * published by the Free Software Foundation. | |
7 | */ | |
8 | #include "omap5.dtsi" | |
9 | #include <dt-bindings/interrupt-controller/irq.h> | |
10 | #include <dt-bindings/interrupt-controller/arm-gic.h> | |
11 | ||
12 | / { | |
13 | aliases { | |
14 | display0 = &hdmi0; | |
15 | }; | |
16 | ||
17 | vmmcsd_fixed: fixedregulator-mmcsd { | |
18 | compatible = "regulator-fixed"; | |
19 | regulator-name = "vmmcsd_fixed"; | |
20 | regulator-min-microvolt = <3000000>; | |
21 | regulator-max-microvolt = <3000000>; | |
22 | }; | |
23 | ||
24 | mmc3_pwrseq: sdhci0_pwrseq { | |
25 | compatible = "mmc-pwrseq-simple"; | |
26 | clocks = <&clk32kgaudio>; | |
27 | clock-names = "ext_clock"; | |
28 | }; | |
29 | ||
30 | vmmcsdio_fixed: fixedregulator-mmcsdio { | |
31 | compatible = "regulator-fixed"; | |
32 | regulator-name = "vmmcsdio_fixed"; | |
33 | regulator-min-microvolt = <1800000>; | |
34 | regulator-max-microvolt = <1800000>; | |
35 | gpio = <&gpio5 12 GPIO_ACTIVE_HIGH>; /* gpio140 WLAN_EN */ | |
36 | enable-active-high; | |
37 | startup-delay-us = <70000>; | |
38 | pinctrl-names = "default"; | |
39 | pinctrl-0 = <&wlan_pins>; | |
40 | }; | |
41 | ||
42 | /* HS USB Host PHY on PORT 2 */ | |
43 | hsusb2_phy: hsusb2_phy { | |
44 | compatible = "usb-nop-xceiv"; | |
45 | reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */ | |
46 | clocks = <&auxclk1_ck>; | |
47 | clock-names = "main_clk"; | |
48 | clock-frequency = <19200000>; | |
49 | }; | |
50 | ||
51 | /* HS USB Host PHY on PORT 3 */ | |
52 | hsusb3_phy: hsusb3_phy { | |
53 | compatible = "usb-nop-xceiv"; | |
54 | reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */ | |
55 | }; | |
56 | ||
57 | leds { | |
58 | compatible = "gpio-leds"; | |
59 | led@1 { | |
60 | label = "omap5:blue:usr1"; | |
61 | gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>; /* gpio5_153 D1 LED */ | |
62 | linux,default-trigger = "heartbeat"; | |
63 | default-state = "off"; | |
64 | }; | |
65 | }; | |
66 | ||
67 | tpd12s015: encoder@0 { | |
68 | compatible = "ti,tpd12s015"; | |
69 | ||
70 | pinctrl-names = "default"; | |
71 | pinctrl-0 = <&tpd12s015_pins>; | |
72 | ||
73 | /* gpios defined in the board specific dts */ | |
74 | ||
75 | ports { | |
76 | #address-cells = <1>; | |
77 | #size-cells = <0>; | |
78 | ||
79 | port@0 { | |
80 | reg = <0>; | |
81 | ||
82 | tpd12s015_in: endpoint@0 { | |
83 | remote-endpoint = <&hdmi_out>; | |
84 | }; | |
85 | }; | |
86 | ||
87 | port@1 { | |
88 | reg = <1>; | |
89 | ||
90 | tpd12s015_out: endpoint@0 { | |
91 | remote-endpoint = <&hdmi_connector_in>; | |
92 | }; | |
93 | }; | |
94 | }; | |
95 | }; | |
96 | ||
97 | hdmi0: connector@0 { | |
98 | compatible = "hdmi-connector"; | |
99 | label = "hdmi"; | |
100 | ||
101 | type = "b"; | |
102 | ||
103 | port { | |
104 | hdmi_connector_in: endpoint { | |
105 | remote-endpoint = <&tpd12s015_out>; | |
106 | }; | |
107 | }; | |
108 | }; | |
109 | ||
110 | sound: sound { | |
111 | compatible = "ti,abe-twl6040"; | |
112 | ti,model = "omap5-uevm"; | |
113 | ||
114 | ti,mclk-freq = <19200000>; | |
115 | ||
116 | ti,mcpdm = <&mcpdm>; | |
117 | ||
118 | ti,twl6040 = <&twl6040>; | |
119 | ||
120 | /* Audio routing */ | |
121 | ti,audio-routing = | |
122 | "Headset Stereophone", "HSOL", | |
123 | "Headset Stereophone", "HSOR", | |
124 | "Line Out", "AUXL", | |
125 | "Line Out", "AUXR", | |
126 | "HSMIC", "Headset Mic", | |
127 | "Headset Mic", "Headset Mic Bias", | |
128 | "AFML", "Line In", | |
129 | "AFMR", "Line In"; | |
130 | }; | |
131 | }; | |
132 | ||
af756bbc TL |
133 | &gpio8 { |
134 | /* TI trees use GPIO instead of msecure, see also muxing */ | |
135 | p234 { | |
136 | gpio-hog; | |
137 | gpios = <10 GPIO_ACTIVE_HIGH>; | |
138 | output-high; | |
139 | line-name = "gpio8_234/msecure"; | |
140 | }; | |
141 | }; | |
142 | ||
ee9a97db TL |
143 | &omap5_pmx_core { |
144 | pinctrl-names = "default"; | |
145 | pinctrl-0 = < | |
146 | &usbhost_pins | |
147 | &led_gpio_pins | |
148 | >; | |
149 | ||
150 | twl6040_pins: pinmux_twl6040_pins { | |
151 | pinctrl-single,pins = < | |
2fcf367a | 152 | OMAP5_IOPAD(0x1be, PIN_OUTPUT | MUX_MODE6) /* mcspi1_somi.gpio5_141 */ |
ee9a97db TL |
153 | >; |
154 | }; | |
155 | ||
156 | mcpdm_pins: pinmux_mcpdm_pins { | |
157 | pinctrl-single,pins = < | |
2fcf367a JMC |
158 | OMAP5_IOPAD(0x182, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */ |
159 | OMAP5_IOPAD(0x19c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_ul_data.abemcpdm_ul_data */ | |
160 | OMAP5_IOPAD(0x19e, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_dl_data.abemcpdm_dl_data */ | |
161 | OMAP5_IOPAD(0x1a0, PIN_INPUT_PULLUP | MUX_MODE0) /* abemcpdm_frame.abemcpdm_frame */ | |
162 | OMAP5_IOPAD(0x1a2, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_lb_clk.abemcpdm_lb_clk */ | |
ee9a97db TL |
163 | >; |
164 | }; | |
165 | ||
166 | mcbsp1_pins: pinmux_mcbsp1_pins { | |
167 | pinctrl-single,pins = < | |
2fcf367a JMC |
168 | OMAP5_IOPAD(0x18c, PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */ |
169 | OMAP5_IOPAD(0x18e, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* abedmic_clk3.abemcbsp1_dx */ | |
170 | OMAP5_IOPAD(0x190, PIN_INPUT | MUX_MODE1) /* abeslimbus1_clock.abemcbsp1_clkx */ | |
171 | OMAP5_IOPAD(0x192, PIN_INPUT_PULLDOWN | MUX_MODE1) /* abeslimbus1_data.abemcbsp1_dr */ | |
ee9a97db TL |
172 | >; |
173 | }; | |
174 | ||
175 | mcbsp2_pins: pinmux_mcbsp2_pins { | |
176 | pinctrl-single,pins = < | |
2fcf367a JMC |
177 | OMAP5_IOPAD(0x194, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dr.abemcbsp2_dr */ |
178 | OMAP5_IOPAD(0x196, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dx.abemcbsp2_dx */ | |
179 | OMAP5_IOPAD(0x198, PIN_INPUT | MUX_MODE0) /* abemcbsp2_fsx.abemcbsp2_fsx */ | |
180 | OMAP5_IOPAD(0x19a, PIN_INPUT | MUX_MODE0) /* abemcbsp2_clkx.abemcbsp2_clkx */ | |
ee9a97db TL |
181 | >; |
182 | }; | |
183 | ||
184 | i2c1_pins: pinmux_i2c1_pins { | |
185 | pinctrl-single,pins = < | |
2fcf367a JMC |
186 | OMAP5_IOPAD(0x1f2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ |
187 | OMAP5_IOPAD(0x1f4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ | |
ee9a97db TL |
188 | >; |
189 | }; | |
190 | ||
191 | mcspi2_pins: pinmux_mcspi2_pins { | |
192 | pinctrl-single,pins = < | |
2fcf367a JMC |
193 | OMAP5_IOPAD(0x0fc, PIN_INPUT | MUX_MODE0) /* mcspi2_clk */ |
194 | OMAP5_IOPAD(0x0fe, PIN_INPUT | MUX_MODE0) /* mcspi2_simo */ | |
195 | OMAP5_IOPAD(0x100, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */ | |
196 | OMAP5_IOPAD(0x102, PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0 */ | |
ee9a97db TL |
197 | >; |
198 | }; | |
199 | ||
200 | mcspi3_pins: pinmux_mcspi3_pins { | |
201 | pinctrl-single,pins = < | |
2fcf367a JMC |
202 | OMAP5_IOPAD(0x0b8, PIN_INPUT | MUX_MODE1) /* mcspi3_somi */ |
203 | OMAP5_IOPAD(0x0ba, PIN_INPUT | MUX_MODE1) /* mcspi3_cs0 */ | |
204 | OMAP5_IOPAD(0x0bc, PIN_INPUT | MUX_MODE1) /* mcspi3_simo */ | |
205 | OMAP5_IOPAD(0x0be, PIN_INPUT | MUX_MODE1) /* mcspi3_clk */ | |
ee9a97db TL |
206 | >; |
207 | }; | |
208 | ||
209 | mmc3_pins: pinmux_mmc3_pins { | |
210 | pinctrl-single,pins = < | |
211 | OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */ | |
212 | OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */ | |
213 | OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */ | |
214 | OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */ | |
215 | OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */ | |
216 | OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */ | |
217 | >; | |
218 | }; | |
219 | ||
220 | wlan_pins: pinmux_wlan_pins { | |
221 | pinctrl-single,pins = < | |
222 | OMAP5_IOPAD(0x1bc, PIN_OUTPUT | MUX_MODE6) /* mcspi1_clk.gpio5_140 */ | |
223 | >; | |
224 | }; | |
225 | ||
af756bbc TL |
226 | /* TI trees use GPIO mode; msecure mode does not work reliably? */ |
227 | palmas_msecure_pins: palmas_msecure_pins { | |
228 | pinctrl-single,pins = < | |
229 | OMAP5_IOPAD(0x180, PIN_OUTPUT | MUX_MODE6) /* gpio8_234 */ | |
230 | >; | |
231 | }; | |
232 | ||
ee9a97db TL |
233 | usbhost_pins: pinmux_usbhost_pins { |
234 | pinctrl-single,pins = < | |
2fcf367a JMC |
235 | OMAP5_IOPAD(0x0c4, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */ |
236 | OMAP5_IOPAD(0x0c6, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */ | |
ee9a97db | 237 | |
2fcf367a JMC |
238 | OMAP5_IOPAD(0x1de, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */ |
239 | OMAP5_IOPAD(0x1e0, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */ | |
ee9a97db | 240 | |
2fcf367a JMC |
241 | OMAP5_IOPAD(0x0b0, PIN_OUTPUT | MUX_MODE6) /* gpio3_80 HUB_NRESET */ |
242 | OMAP5_IOPAD(0x0ae, PIN_OUTPUT | MUX_MODE6) /* gpio3_79 ETH_NRESET */ | |
ee9a97db TL |
243 | >; |
244 | }; | |
245 | ||
246 | led_gpio_pins: pinmux_led_gpio_pins { | |
247 | pinctrl-single,pins = < | |
2fcf367a | 248 | OMAP5_IOPAD(0x1d6, PIN_OUTPUT | MUX_MODE6) /* uart3_cts_rctx.gpio5_153 */ |
ee9a97db TL |
249 | >; |
250 | }; | |
251 | ||
252 | uart1_pins: pinmux_uart1_pins { | |
253 | pinctrl-single,pins = < | |
2fcf367a JMC |
254 | OMAP5_IOPAD(0x0a0, PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_cts */ |
255 | OMAP5_IOPAD(0x0a2, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_tx.uart1_cts */ | |
256 | OMAP5_IOPAD(0x0a4, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rx.uart1_rts */ | |
257 | OMAP5_IOPAD(0x0a6, PIN_OUTPUT | MUX_MODE0) /* uart1_rx.uart1_rts */ | |
ee9a97db TL |
258 | >; |
259 | }; | |
260 | ||
261 | uart3_pins: pinmux_uart3_pins { | |
262 | pinctrl-single,pins = < | |
2fcf367a JMC |
263 | OMAP5_IOPAD(0x1da, PIN_OUTPUT | MUX_MODE0) /* uart3_rts_irsd.uart3_tx_irtx */ |
264 | OMAP5_IOPAD(0x1dc, PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_rx_irrx.uart3_usbb3_hsic */ | |
ee9a97db TL |
265 | >; |
266 | }; | |
267 | ||
268 | uart5_pins: pinmux_uart5_pins { | |
269 | pinctrl-single,pins = < | |
2fcf367a JMC |
270 | OMAP5_IOPAD(0x1b0, PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_rx.uart5_rx */ |
271 | OMAP5_IOPAD(0x1b2, PIN_OUTPUT | MUX_MODE0) /* uart5_tx.uart5_tx */ | |
272 | OMAP5_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_cts.uart5_rts */ | |
273 | OMAP5_IOPAD(0x1b6, PIN_OUTPUT | MUX_MODE0) /* uart5_cts.uart5_rts */ | |
ee9a97db TL |
274 | >; |
275 | }; | |
276 | ||
277 | dss_hdmi_pins: pinmux_dss_hdmi_pins { | |
278 | pinctrl-single,pins = < | |
2fcf367a JMC |
279 | OMAP5_IOPAD(0x13c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ |
280 | OMAP5_IOPAD(0x140, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl.hdmi_ddc_scl */ | |
281 | OMAP5_IOPAD(0x142, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda.hdmi_ddc_sda */ | |
ee9a97db TL |
282 | >; |
283 | }; | |
284 | ||
285 | tpd12s015_pins: pinmux_tpd12s015_pins { | |
286 | pinctrl-single,pins = < | |
2fcf367a | 287 | OMAP5_IOPAD(0x13e, PIN_INPUT_PULLDOWN | MUX_MODE6) /* hdmi_hpd.gpio7_193 */ |
ee9a97db TL |
288 | >; |
289 | }; | |
290 | }; | |
291 | ||
292 | &omap5_pmx_wkup { | |
293 | pinctrl-names = "default"; | |
294 | pinctrl-0 = < | |
295 | &usbhost_wkup_pins | |
296 | >; | |
297 | ||
af756bbc TL |
298 | palmas_sys_nirq_pins: pinmux_palmas_sys_nirq_pins { |
299 | pinctrl-single,pins = < | |
300 | OMAP5_IOPAD(0x068, PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq1 */ | |
301 | >; | |
302 | }; | |
303 | ||
ee9a97db TL |
304 | usbhost_wkup_pins: pinmux_usbhost_wkup_pins { |
305 | pinctrl-single,pins = < | |
2fcf367a | 306 | OMAP5_IOPAD(0x05a, PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */ |
ee9a97db TL |
307 | >; |
308 | }; | |
309 | ||
310 | wlcore_irq_pin: pinmux_wlcore_irq_pin { | |
311 | pinctrl-single,pins = < | |
2fcf367a | 312 | OMAP5_IOPAD(0x40, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE6) /* llia_wakereqin.gpio1_wk14 */ |
ee9a97db TL |
313 | >; |
314 | }; | |
315 | }; | |
316 | ||
317 | &mmc1 { | |
318 | vmmc-supply = <&ldo9_reg>; | |
319 | bus-width = <4>; | |
320 | }; | |
321 | ||
322 | &mmc2 { | |
323 | vmmc-supply = <&vmmcsd_fixed>; | |
324 | bus-width = <8>; | |
325 | ti,non-removable; | |
326 | }; | |
327 | ||
328 | &mmc3 { | |
329 | vmmc-supply = <&vmmcsdio_fixed>; | |
330 | mmc-pwrseq = <&mmc3_pwrseq>; | |
331 | bus-width = <4>; | |
332 | non-removable; | |
333 | cap-power-off-card; | |
334 | pinctrl-names = "default"; | |
335 | pinctrl-0 = <&mmc3_pins &wlcore_irq_pin>; | |
336 | interrupts-extended = <&gic GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH | |
337 | &omap5_pmx_core 0x168>; | |
338 | ||
339 | #address-cells = <1>; | |
340 | #size-cells = <0>; | |
341 | wlcore: wlcore@2 { | |
342 | compatible = "ti,wl1271"; | |
343 | reg = <2>; | |
344 | interrupt-parent = <&gpio1>; | |
345 | interrupts = <14 IRQ_TYPE_LEVEL_HIGH>; /* gpio 14 */ | |
346 | ref-clock-frequency = <26000000>; | |
347 | }; | |
348 | }; | |
349 | ||
350 | &mmc4 { | |
351 | status = "disabled"; | |
352 | }; | |
353 | ||
354 | &mmc5 { | |
355 | status = "disabled"; | |
356 | }; | |
357 | ||
358 | &i2c1 { | |
359 | pinctrl-names = "default"; | |
360 | pinctrl-0 = <&i2c1_pins>; | |
361 | ||
362 | clock-frequency = <400000>; | |
363 | ||
364 | palmas: palmas@48 { | |
365 | compatible = "ti,palmas"; | |
366 | interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */ | |
367 | reg = <0x48>; | |
368 | interrupt-controller; | |
369 | #interrupt-cells = <2>; | |
370 | ti,system-power-controller; | |
af756bbc TL |
371 | pinctrl-names = "default"; |
372 | pinctrl-0 = <&palmas_sys_nirq_pins &palmas_msecure_pins>; | |
ee9a97db TL |
373 | |
374 | extcon_usb3: palmas_usb { | |
375 | compatible = "ti,palmas-usb-vid"; | |
376 | ti,enable-vbus-detection; | |
377 | ti,enable-id-detection; | |
378 | ti,wakeup; | |
379 | }; | |
380 | ||
381 | clk32kgaudio: palmas_clk32k@1 { | |
382 | compatible = "ti,palmas-clk32kgaudio"; | |
383 | #clock-cells = <0>; | |
384 | }; | |
385 | ||
c08659d4 NS |
386 | rtc { |
387 | compatible = "ti,palmas-rtc"; | |
388 | interrupt-parent = <&palmas>; | |
389 | interrupts = <8 IRQ_TYPE_NONE>; | |
390 | ti,backup-battery-chargeable; | |
391 | ti,backup-battery-charge-high-current; | |
392 | }; | |
393 | ||
ee9a97db TL |
394 | palmas_pmic { |
395 | compatible = "ti,palmas-pmic"; | |
396 | interrupt-parent = <&palmas>; | |
397 | interrupts = <14 IRQ_TYPE_NONE>; | |
398 | interrupt-name = "short-irq"; | |
399 | ||
400 | ti,ldo6-vibrator; | |
401 | ||
402 | regulators { | |
403 | smps123_reg: smps123 { | |
404 | /* VDD_OPP_MPU */ | |
405 | regulator-name = "smps123"; | |
406 | regulator-min-microvolt = < 600000>; | |
407 | regulator-max-microvolt = <1500000>; | |
408 | regulator-always-on; | |
409 | regulator-boot-on; | |
410 | }; | |
411 | ||
412 | smps45_reg: smps45 { | |
413 | /* VDD_OPP_MM */ | |
414 | regulator-name = "smps45"; | |
415 | regulator-min-microvolt = < 600000>; | |
416 | regulator-max-microvolt = <1310000>; | |
417 | regulator-always-on; | |
418 | regulator-boot-on; | |
419 | }; | |
420 | ||
421 | smps6_reg: smps6 { | |
422 | /* VDD_DDR3 - over VDD_SMPS6 */ | |
423 | regulator-name = "smps6"; | |
424 | regulator-min-microvolt = <1200000>; | |
425 | regulator-max-microvolt = <1200000>; | |
426 | regulator-always-on; | |
427 | regulator-boot-on; | |
428 | }; | |
429 | ||
430 | smps7_reg: smps7 { | |
431 | /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */ | |
432 | regulator-name = "smps7"; | |
433 | regulator-min-microvolt = <1800000>; | |
434 | regulator-max-microvolt = <1800000>; | |
435 | regulator-always-on; | |
436 | regulator-boot-on; | |
437 | }; | |
438 | ||
439 | smps8_reg: smps8 { | |
440 | /* VDD_OPP_CORE */ | |
441 | regulator-name = "smps8"; | |
442 | regulator-min-microvolt = < 600000>; | |
443 | regulator-max-microvolt = <1310000>; | |
444 | regulator-always-on; | |
445 | regulator-boot-on; | |
446 | }; | |
447 | ||
448 | smps9_reg: smps9 { | |
449 | /* VDDA_2v1_AUD over VDD_2v1 */ | |
450 | regulator-name = "smps9"; | |
451 | regulator-min-microvolt = <2100000>; | |
452 | regulator-max-microvolt = <2100000>; | |
453 | ti,smps-range = <0x80>; | |
454 | }; | |
455 | ||
456 | smps10_out2_reg: smps10_out2 { | |
457 | /* VBUS_5V_OTG */ | |
458 | regulator-name = "smps10_out2"; | |
459 | regulator-min-microvolt = <5000000>; | |
460 | regulator-max-microvolt = <5000000>; | |
461 | regulator-always-on; | |
462 | regulator-boot-on; | |
463 | }; | |
464 | ||
465 | smps10_out1_reg: smps10_out1 { | |
466 | /* VBUS_5V_OTG */ | |
467 | regulator-name = "smps10_out1"; | |
468 | regulator-min-microvolt = <5000000>; | |
469 | regulator-max-microvolt = <5000000>; | |
470 | }; | |
471 | ||
472 | ldo1_reg: ldo1 { | |
473 | /* VDDAPHY_CAM: vdda_csiport */ | |
474 | regulator-name = "ldo1"; | |
475 | regulator-min-microvolt = <1500000>; | |
476 | regulator-max-microvolt = <1800000>; | |
477 | }; | |
478 | ||
479 | ldo2_reg: ldo2 { | |
480 | /* VCC_2V8_DISP: Does not go anywhere */ | |
481 | regulator-name = "ldo2"; | |
482 | regulator-min-microvolt = <2800000>; | |
483 | regulator-max-microvolt = <2800000>; | |
484 | /* Unused */ | |
485 | status = "disabled"; | |
486 | }; | |
487 | ||
488 | ldo3_reg: ldo3 { | |
489 | /* VDDAPHY_MDM: vdda_lli */ | |
490 | regulator-name = "ldo3"; | |
491 | regulator-min-microvolt = <1500000>; | |
492 | regulator-max-microvolt = <1500000>; | |
493 | regulator-boot-on; | |
494 | /* Only if Modem is used */ | |
495 | status = "disabled"; | |
496 | }; | |
497 | ||
498 | ldo4_reg: ldo4 { | |
499 | /* VDDAPHY_DISP: vdda_dsiport/hdmi */ | |
500 | regulator-name = "ldo4"; | |
501 | regulator-min-microvolt = <1500000>; | |
502 | regulator-max-microvolt = <1800000>; | |
503 | }; | |
504 | ||
505 | ldo5_reg: ldo5 { | |
506 | /* VDDA_1V8_PHY: usb/sata/hdmi.. */ | |
507 | regulator-name = "ldo5"; | |
508 | regulator-min-microvolt = <1800000>; | |
509 | regulator-max-microvolt = <1800000>; | |
510 | regulator-always-on; | |
511 | regulator-boot-on; | |
512 | }; | |
513 | ||
514 | ldo6_reg: ldo6 { | |
515 | /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */ | |
516 | regulator-name = "ldo6"; | |
517 | regulator-min-microvolt = <1200000>; | |
518 | regulator-max-microvolt = <1200000>; | |
519 | regulator-always-on; | |
520 | regulator-boot-on; | |
521 | }; | |
522 | ||
523 | ldo7_reg: ldo7 { | |
524 | /* VDD_VPP: vpp1 */ | |
525 | regulator-name = "ldo7"; | |
526 | regulator-min-microvolt = <2000000>; | |
527 | regulator-max-microvolt = <2000000>; | |
528 | /* Only for efuse reprograming! */ | |
529 | status = "disabled"; | |
530 | }; | |
531 | ||
532 | ldo8_reg: ldo8 { | |
533 | /* VDD_3v0: Does not go anywhere */ | |
534 | regulator-name = "ldo8"; | |
535 | regulator-min-microvolt = <3000000>; | |
536 | regulator-max-microvolt = <3000000>; | |
537 | regulator-boot-on; | |
538 | /* Unused */ | |
539 | status = "disabled"; | |
540 | }; | |
541 | ||
542 | ldo9_reg: ldo9 { | |
543 | /* VCC_DV_SDIO: vdds_sdcard */ | |
544 | regulator-name = "ldo9"; | |
545 | regulator-min-microvolt = <1800000>; | |
546 | regulator-max-microvolt = <3000000>; | |
547 | regulator-boot-on; | |
548 | }; | |
549 | ||
550 | ldoln_reg: ldoln { | |
551 | /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */ | |
552 | regulator-name = "ldoln"; | |
553 | regulator-min-microvolt = <1800000>; | |
554 | regulator-max-microvolt = <1800000>; | |
555 | regulator-always-on; | |
556 | regulator-boot-on; | |
557 | }; | |
558 | ||
559 | ldousb_reg: ldousb { | |
560 | /* VDDA_3V_USB: VDDA_USBHS33 */ | |
561 | regulator-name = "ldousb"; | |
562 | regulator-min-microvolt = <3250000>; | |
563 | regulator-max-microvolt = <3250000>; | |
564 | regulator-always-on; | |
565 | regulator-boot-on; | |
566 | }; | |
567 | ||
568 | regen3_reg: regen3 { | |
569 | /* REGEN3 controls LDO9 supply to card */ | |
570 | regulator-name = "regen3"; | |
571 | regulator-always-on; | |
572 | regulator-boot-on; | |
573 | }; | |
574 | }; | |
575 | }; | |
576 | ||
577 | palmas_power_button: palmas_power_button { | |
578 | compatible = "ti,palmas-pwrbutton"; | |
579 | interrupt-parent = <&palmas>; | |
580 | interrupts = <1 IRQ_TYPE_EDGE_FALLING>; | |
581 | wakeup-source; | |
582 | }; | |
583 | }; | |
584 | ||
585 | twl6040: twl@4b { | |
586 | compatible = "ti,twl6040"; | |
587 | reg = <0x4b>; | |
588 | ||
589 | pinctrl-names = "default"; | |
590 | pinctrl-0 = <&twl6040_pins>; | |
591 | ||
592 | interrupts = <GIC_SPI 119 IRQ_TYPE_NONE>; /* IRQ_SYS_2N cascaded to gic */ | |
593 | ti,audpwron-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>; /* gpio line 141 */ | |
594 | ||
595 | vio-supply = <&smps7_reg>; | |
596 | v2v1-supply = <&smps9_reg>; | |
597 | enable-active-high; | |
598 | ||
599 | clocks = <&clk32kgaudio>; | |
600 | clock-names = "clk32k"; | |
601 | }; | |
602 | }; | |
603 | ||
604 | &mcpdm { | |
605 | pinctrl-names = "default"; | |
606 | pinctrl-0 = <&mcpdm_pins>; | |
607 | status = "okay"; | |
608 | }; | |
609 | ||
610 | &mcbsp1 { | |
611 | pinctrl-names = "default"; | |
612 | pinctrl-0 = <&mcbsp1_pins>; | |
613 | status = "okay"; | |
614 | }; | |
615 | ||
616 | &mcbsp2 { | |
617 | pinctrl-names = "default"; | |
618 | pinctrl-0 = <&mcbsp2_pins>; | |
619 | status = "okay"; | |
620 | }; | |
621 | ||
622 | &usbhshost { | |
623 | port2-mode = "ehci-hsic"; | |
624 | port3-mode = "ehci-hsic"; | |
625 | }; | |
626 | ||
627 | &usbhsehci { | |
628 | phys = <0 &hsusb2_phy &hsusb3_phy>; | |
629 | }; | |
630 | ||
631 | &usb3 { | |
632 | extcon = <&extcon_usb3>; | |
633 | vbus-supply = <&smps10_out1_reg>; | |
634 | }; | |
635 | ||
636 | &mcspi1 { | |
637 | ||
638 | }; | |
639 | ||
640 | &mcspi2 { | |
641 | pinctrl-names = "default"; | |
642 | pinctrl-0 = <&mcspi2_pins>; | |
643 | }; | |
644 | ||
645 | &mcspi3 { | |
646 | pinctrl-names = "default"; | |
647 | pinctrl-0 = <&mcspi3_pins>; | |
648 | }; | |
649 | ||
650 | &uart1 { | |
651 | pinctrl-names = "default"; | |
652 | pinctrl-0 = <&uart1_pins>; | |
653 | }; | |
654 | ||
655 | &uart3 { | |
656 | pinctrl-names = "default"; | |
657 | pinctrl-0 = <&uart3_pins>; | |
658 | interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>, | |
659 | <&omap5_pmx_core 0x19c>; | |
660 | }; | |
661 | ||
662 | &uart5 { | |
663 | pinctrl-names = "default"; | |
664 | pinctrl-0 = <&uart5_pins>; | |
665 | }; | |
666 | ||
667 | &cpu0 { | |
668 | cpu0-supply = <&smps123_reg>; | |
669 | }; | |
670 | ||
671 | &dss { | |
672 | status = "ok"; | |
673 | }; | |
674 | ||
675 | &hdmi { | |
676 | status = "ok"; | |
677 | ||
678 | /* vdda-supply populated in board specific dts file */ | |
679 | ||
680 | pinctrl-names = "default"; | |
681 | pinctrl-0 = <&dss_hdmi_pins>; | |
682 | ||
683 | port { | |
684 | hdmi_out: endpoint { | |
685 | remote-endpoint = <&tpd12s015_in>; | |
686 | }; | |
687 | }; | |
688 | }; |