[deliverable/linux.git] / arch / arm / boot / dts / qcom-apq8064-cm-qs600.dts

#include "qcom-apq8064-v2.0.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>

/ {
	model = "CompuLab CM-QS600";
	compatible = "qcom,apq8064-cm-qs600", "qcom,apq8064";

	aliases {
		serial0 = &gsbi7_serial;
	};

	chosen {
		stdout-path = "serial0:115200n8";
	};

	pwrseq {
		#address-cells = <1>;
		#size-cells = <1>;
		ranges;
		compatible = "simple-bus";

		sdcc4_pwrseq: sdcc4_pwrseq {
			pinctrl-names = "default";
			pinctrl-0 = <&wlan_default_gpios>;
			compatible = "mmc-pwrseq-simple";
			reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>;
		};
	};

	soc {
		rpm@108000 {
			regulators {
				vin_lvs1_3_6-supply = <&pm8921_s4>;
				vin_lvs2-supply = <&pm8921_s1>;
				vin_lvs4_5_7-supply = <&pm8921_s4>;

				vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
				vdd_l24-supply = <&pm8921_s1>;
				vdd_l25-supply = <&pm8921_s1>;
				vdd_l26-supply = <&pm8921_s7>;
				vdd_l27-supply = <&pm8921_s7>;
				vdd_l28-supply = <&pm8921_s7>;


				/* Buck SMPS */
				pm8921_s1: s1 {
					regulator-always-on;
					regulator-min-microvolt = <1225000>;
					regulator-max-microvolt = <1225000>;
					qcom,switch-mode-frequency = <3200000>;
					bias-pull-down;
				};

				pm8921_s3: s3 {
					regulator-min-microvolt = <1000000>;
					regulator-max-microvolt = <1400000>;
					qcom,switch-mode-frequency = <4800000>;
				};

				pm8921_s4: s4 {
					regulator-min-microvolt	= <1800000>;
					regulator-max-microvolt	= <1800000>;
					qcom,switch-mode-frequency = <3200000>;
				};

				pm8921_s7: s7 {
					regulator-min-microvolt = <1300000>;
					regulator-max-microvolt = <1300000>;
					qcom,switch-mode-frequency = <3200000>;
				};

				pm8921_l3: l3 {
					regulator-min-microvolt = <3050000>;
					regulator-max-microvolt = <3300000>;
					bias-pull-down;
				};

				pm8921_l4: l4 {
					regulator-min-microvolt = <1000000>;
					regulator-max-microvolt = <1800000>;
					bias-pull-down;
				};

				pm8921_l5: l5 {
					regulator-min-microvolt = <2750000>;
					regulator-max-microvolt = <3000000>;
					bias-pull-down;
				};

				pm8921_l23: l23 {
					regulator-min-microvolt = <1700000>;
					regulator-max-microvolt = <1900000>;
					bias-pull-down;
				};
			};
		};

		gsbi@12440000 {
			status = "okay";
			qcom,mode = <GSBI_PROT_I2C>;

			i2c@12460000 {
				status = "okay";
				clock-frequency = <200000>;

				eeprom@50 {
					compatible = "24c02";
					reg = <0x50>;
					pagesize = <32>;
				};
			};
		};

		gsbi@16600000 {
			status = "ok";
			qcom,mode = <GSBI_PROT_I2C_UART>;
			serial@16640000 {
				status = "ok";
				pinctrl-names = "default";
				pinctrl-0 = <&gsbi7_uart_2pins>;
			};
		};

		/* OTG */
		usb1_phy: phy@12500000 {
			status		= "okay";
			vddcx-supply	= <&pm8921_s3>;
			v3p3-supply	= <&pm8921_l3>;
			v1p8-supply	= <&pm8921_l4>;
		};

		usb3_phy: phy@12520000 {
			status		= "okay";
			vddcx-supply	= <&pm8921_s3>;
			v3p3-supply	= <&pm8921_l3>;
			v1p8-supply	= <&pm8921_l23>;
		};

		usb4_phy: phy@12530000 {
			status		= "okay";
			vddcx-supply	= <&pm8921_s3>;
			v3p3-supply	= <&pm8921_l3>;
			v1p8-supply	= <&pm8921_l23>;
		};

		gadget1: gadget@12500000 {
			status = "ok";
		};

		/* OTG */
		usb1: usb@12500000 {
			status = "ok";
		};

		usb3: usb@12520000 {
			status = "okay";
		};

		usb4: usb@12530000 {
			status = "okay";
		};

		/* on board fixed 3.3v supply */
		v3p3_fixed: v3p3 {
			compatible = "regulator-fixed";
			regulator-name = "PCIE V3P3";
			regulator-min-microvolt = <3300000>;
			regulator-max-microvolt = <3300000>;
			regulator-always-on;
		};

		qcom,ssbi@500000 {
			pmic@0 {
				gpio@150 {
					wlan_default_gpios: wlan-gpios {
						pios {
							pins = "gpio43";
							function = "normal";
							bias-disable;
							power-source = <PM8921_GPIO_S4>;
						};
					};
				};
			};
		};

		amba {
			/* eMMC */
			sdcc1: sdcc@12400000 {
				status = "okay";
				vmmc-supply = <&pm8921_l5>;
				vqmmc-supply = <&pm8921_s4>;
			};

			/* External micro SD card */
			sdcc3: sdcc@12180000 {
				status = "okay";
				vmmc-supply = <&v3p3_fixed>;
			};
			/* WLAN */
			sdcc4: sdcc@121c0000 {
				status = "okay";
				vmmc-supply = <&v3p3_fixed>;
				vqmmc-supply = <&v3p3_fixed>;
				mmc-pwrseq = <&sdcc4_pwrseq>;
			};
		};
	};
};
Commit	Line	Data
7dac24bd	1	#include "qcom-apq8064-v2.0.dtsi"
f0b6d950 SK	2	#include <dt-bindings/gpio/gpio.h>
f0b6d950 SK	3	#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
7dac24bd MR	4
	5	/ {
	6	model = "CompuLab CM-QS600";
	7	compatible = "qcom,apq8064-cm-qs600", "qcom,apq8064";
	8
4e19db11 SB	9	aliases {
	10	serial0 = &gsbi7_serial;
	11	};
	12
	13	chosen {
	14	stdout-path = "serial0:115200n8";
	15	};
	16
f0b6d950 SK	17	pwrseq {
	18	#address-cells = <1>;
	19	#size-cells = <1>;
	20	ranges;
	21	compatible = "simple-bus";
	22
	23	sdcc4_pwrseq: sdcc4_pwrseq {
	24	pinctrl-names = "default";
	25	pinctrl-0 = <&wlan_default_gpios>;
	26	compatible = "mmc-pwrseq-simple";
	27	reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>;
	28	};
	29	};
	30
7dac24bd	31	soc {
1a621d35 SK	32	rpm@108000 {
	33	regulators {
	34	vin_lvs1_3_6-supply = <&pm8921_s4>;
	35	vin_lvs2-supply = <&pm8921_s1>;
	36	vin_lvs4_5_7-supply = <&pm8921_s4>;
	37
	38	vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
	39	vdd_l24-supply = <&pm8921_s1>;
	40	vdd_l25-supply = <&pm8921_s1>;
	41	vdd_l26-supply = <&pm8921_s7>;
	42	vdd_l27-supply = <&pm8921_s7>;
	43	vdd_l28-supply = <&pm8921_s7>;
	44
	45
	46	/* Buck SMPS */
	47	pm8921_s1: s1 {
	48	regulator-always-on;
	49	regulator-min-microvolt = <1225000>;
	50	regulator-max-microvolt = <1225000>;
	51	qcom,switch-mode-frequency = <3200000>;
	52	bias-pull-down;
	53	};
	54
	55	pm8921_s3: s3 {
	56	regulator-min-microvolt = <1000000>;
	57	regulator-max-microvolt = <1400000>;
	58	qcom,switch-mode-frequency = <4800000>;
	59	};
	60
	61	pm8921_s4: s4 {
	62	regulator-min-microvolt = <1800000>;
	63	regulator-max-microvolt = <1800000>;
	64	qcom,switch-mode-frequency = <3200000>;
	65	};
	66
	67	pm8921_s7: s7 {
	68	regulator-min-microvolt = <1300000>;
	69	regulator-max-microvolt = <1300000>;
	70	qcom,switch-mode-frequency = <3200000>;
	71	};
	72
	73	pm8921_l3: l3 {
	74	regulator-min-microvolt = <3050000>;
	75	regulator-max-microvolt = <3300000>;
	76	bias-pull-down;
	77	};
	78
	79	pm8921_l4: l4 {
	80	regulator-min-microvolt = <1000000>;
	81	regulator-max-microvolt = <1800000>;
	82	bias-pull-down;
	83	};
	84
baff39e6 SK	85	pm8921_l5: l5 {
	86	regulator-min-microvolt = <2750000>;
	87	regulator-max-microvolt = <3000000>;
	88	bias-pull-down;
	89	};
	90
1a621d35 SK	91	pm8921_l23: l23 {
	92	regulator-min-microvolt = <1700000>;
	93	regulator-max-microvolt = <1900000>;
	94	bias-pull-down;
	95	};
	96	};
	97	};
	98
7dac24bd MR	99	gsbi@12440000 {
	100	status = "okay";
	101	qcom,mode = <GSBI_PROT_I2C>;
	102
	103	i2c@12460000 {
	104	status = "okay";
	105	clock-frequency = <200000>;
7dac24bd	106
2c9c2e5a	107	eeprom@50 {
7dac24bd MR	108	compatible = "24c02";
	109	reg = <0x50>;
	110	pagesize = <32>;
	111	};
	112	};
	113	};
	114
	115	gsbi@16600000 {
	116	status = "ok";
	117	qcom,mode = <GSBI_PROT_I2C_UART>;
	118	serial@16640000 {
	119	status = "ok";
be87cd0e SK	120	pinctrl-names = "default";
be87cd0e SK	121	pinctrl-0 = <&gsbi7_uart_2pins>;
7dac24bd MR	122	};
	123	};
	124
08372ce9 ND	125	/* OTG */
	126	usb1_phy: phy@12500000 {
	127	status = "okay";
	128	vddcx-supply = <&pm8921_s3>;
	129	v3p3-supply = <&pm8921_l3>;
	130	v1p8-supply = <&pm8921_l4>;
	131	};
	132
84db78b8 ND	133	usb3_phy: phy@12520000 {
	134	status = "okay";
	135	vddcx-supply = <&pm8921_s3>;
	136	v3p3-supply = <&pm8921_l3>;
	137	v1p8-supply = <&pm8921_l23>;
	138	};
	139
	140	usb4_phy: phy@12530000 {
	141	status = "okay";
	142	vddcx-supply = <&pm8921_s3>;
	143	v3p3-supply = <&pm8921_l3>;
	144	v1p8-supply = <&pm8921_l23>;
	145	};
	146
08372ce9 ND	147	gadget1: gadget@12500000 {
	148	status = "ok";
	149	};
	150
	151	/* OTG */
	152	usb1: usb@12500000 {
	153	status = "ok";
	154	};
	155
84db78b8 ND	156	usb3: usb@12520000 {
	157	status = "okay";
	158	};
	159
	160	usb4: usb@12530000 {
	161	status = "okay";
	162	};
	163
baff39e6 SK	164	/* on board fixed 3.3v supply */
	165	v3p3_fixed: v3p3 {
	166	compatible = "regulator-fixed";
	167	regulator-name = "PCIE V3P3";
	168	regulator-min-microvolt = <3300000>;
	169	regulator-max-microvolt = <3300000>;
	170	regulator-always-on;
	171	};
	172
f0b6d950 SK	173	qcom,ssbi@500000 {
	174	pmic@0 {
	175	gpio@150 {
	176	wlan_default_gpios: wlan-gpios {
	177	pios {
	178	pins = "gpio43";
	179	function = "normal";
	180	bias-disable;
	181	power-source = <PM8921_GPIO_S4>;
	182	};
	183	};
	184	};
	185	};
	186	};
	187
7dac24bd MR	188	amba {
	189	/* eMMC */
	190	sdcc1: sdcc@12400000 {
	191	status = "okay";
baff39e6 SK	192	vmmc-supply = <&pm8921_l5>;
baff39e6 SK	193	vqmmc-supply = <&pm8921_s4>;
7dac24bd MR	194	};
	195
	196	/* External micro SD card */
	197	sdcc3: sdcc@12180000 {
	198	status = "okay";
baff39e6	199	vmmc-supply = <&v3p3_fixed>;
7dac24bd MR	200	};
	201	/* WLAN */
	202	sdcc4: sdcc@121c0000 {
	203	status = "okay";
baff39e6 SK	204	vmmc-supply = <&v3p3_fixed>;
baff39e6 SK	205	vqmmc-supply = <&v3p3_fixed>;
f0b6d950	206	mmc-pwrseq = <&sdcc4_pwrseq>;
7dac24bd MR	207	};
	208	};
	209	};
	210	};