[deliverable/linux.git] / arch / arm / boot / dts / sama5d3xmb.dtsi

/*
 * sama5d3xmb.dts - Device Tree file for SAMA5D3x mother board
 *
 *  Copyright (C) 2013 Atmel,
 *                2013 Ludovic Desroches <ludovic.desroches@atmel.com>
 *
 * Licensed under GPLv2 or later.
 */
#include "sama5d3xcm.dtsi"

/ {
	compatible = "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";

	ahb {
		apb {
			mmc0: mmc@f0000000 {
				pinctrl-names = "default";
				pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
				status = "okay";
				slot@0 {
					reg = <0>;
					bus-width = <4>;
					cd-gpios = <&pioD 17 GPIO_ACTIVE_HIGH>;
				};
			};

			spi0: spi@f0004000 {
				dmas = <0>, <0>;	/*  Do not use DMA for spi0 */

				m25p80@0 {
					compatible = "atmel,at25df321a";
					spi-max-frequency = <50000000>;
					reg = <0>;
				};
			};

			ssc0: ssc@f0008000 {
				atmel,clk-from-rk-pin;
			};

			/*
			 * i2c0 conflicts with ISI:
			 * disable it to allow the use of ISI
			 * can not enable audio when i2c0 disabled
			 */
			i2c0: i2c@f0014000 {
				wm8904: wm8904@1a {
					compatible = "wm8904";
					reg = <0x1a>;
					clocks = <&pck0>;
					clock-names = "mclk";
				};
			};

			usart1: serial@f0020000 {
				dmas = <0>, <0>;	/*  Do not use DMA for usart1 */
				pinctrl-names = "default";
				pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
				status = "okay";
			};

			isi: isi@f0034000 {
				pinctrl-names = "default";
				pinctrl-0 = <&pinctrl_isi &pinctrl_isi_pck_as_mck &pinctrl_isi_power &pinctrl_isi_reset>;
			};

			mmc1: mmc@f8000000 {
				pinctrl-names = "default";
				pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
				status = "okay";
				slot@0 {
					reg = <0>;
					bus-width = <4>;
					cd-gpios = <&pioD 18 GPIO_ACTIVE_HIGH>;
				};
			};

			adc0: adc@f8018000 {
				pinctrl-names = "default";
				pinctrl-0 = <
					&pinctrl_adc0_adtrg
					&pinctrl_adc0_ad0
					&pinctrl_adc0_ad1
					&pinctrl_adc0_ad2
					&pinctrl_adc0_ad3
					&pinctrl_adc0_ad4
					>;
				status = "okay";
			};

			macb1: ethernet@f802c000 {
				phy-mode = "rmii";

				#address-cells = <1>;
				#size-cells = <0>;
				phy0: ethernet-phy@1 {
					interrupt-parent = <&pioE>;
					interrupts = <30 IRQ_TYPE_EDGE_FALLING>;
					reg = <1>;
				};
			};

			pinctrl@fffff200 {
				board {
					pinctrl_mmc0_cd: mmc0_cd {
						atmel,pins =
							<AT91_PIOD 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD17 GPIO with pullup deglitch */
					};

					pinctrl_mmc1_cd: mmc1_cd {
						atmel,pins =
							<AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD18 GPIO with pullup deglitch */
					};

					pinctrl_pck0_as_audio_mck: pck0_as_audio_mck {
						atmel,pins =
							<AT91_PIOD 30 AT91_PERIPH_B AT91_PINCTRL_NONE>;	/* PD30 periph B */
					};

					pinctrl_isi_reset: isi_reset-0 {
						atmel,pins =
							<AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;   /* PE24 gpio */
					};

					pinctrl_isi_power: isi_power-0 {
						atmel,pins =
							<AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE29 gpio */
					};

					pinctrl_usba_vbus: usba_vbus {
						atmel,pins =
							<AT91_PIOD 29 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PD29 GPIO with deglitch */
					};
				};
			};

			dbgu: serial@ffffee00 {
				dmas = <0>, <0>;	/*  Do not use DMA for dbgu */
				status = "okay";
			};

			watchdog@fffffe40 {
				status = "okay";
			};
		};

		usb0: gadget@00500000 {
			atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
			pinctrl-names = "default";
			pinctrl-0 = <&pinctrl_usba_vbus>;
			status = "okay";
		};

		usb1: ohci@00600000 {
			num-ports = <3>;
			atmel,vbus-gpio = <&pioD 25 GPIO_ACTIVE_HIGH
					   &pioD 26 GPIO_ACTIVE_LOW
					   &pioD 27 GPIO_ACTIVE_LOW
					  >;
			status = "okay";
		};

		usb2: ehci@00700000 {
			status = "okay";
		};
	};

	sound {
		compatible = "atmel,asoc-wm8904";
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_pck0_as_audio_mck>;

		atmel,model = "wm8904 @ SAMA5D3EK";
		atmel,audio-routing =
			"Headphone Jack", "HPOUTL",
			"Headphone Jack", "HPOUTR",
			"IN2L", "Line In Jack",
			"IN2R", "Line In Jack",
			"MICBIAS", "IN1L",
			"IN1L", "Mic";

		atmel,ssc-controller = <&ssc0>;
		atmel,audio-codec = <&wm8904>;

		status = "disabled";
	};
};
Commit	Line	Data
655ff266 LD	1	/*
	2	* sama5d3xmb.dts - Device Tree file for SAMA5D3x mother board
	3	*
	4	* Copyright (C) 2013 Atmel,
	5	* 2013 Ludovic Desroches <ludovic.desroches@atmel.com>
	6	*
	7	* Licensed under GPLv2 or later.
	8	*/
6db64d29	9	#include "sama5d3xcm.dtsi"
655ff266 LD	10
	11	/ {
	12	compatible = "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
	13
	14	ahb {
	15	apb {
	16	mmc0: mmc@f0000000 {
	17	pinctrl-names = "default";
	18	pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
	19	status = "okay";
	20	slot@0 {
	21	reg = <0>;
	22	bus-width = <4>;
92f8629b	23	cd-gpios = <&pioD 17 GPIO_ACTIVE_HIGH>;
655ff266 LD	24	};
	25	};
	26
	27	spi0: spi@f0004000 {
fe855dbf BS	28	dmas = <0>, <0>; /* Do not use DMA for spi0 */
fe855dbf BS	29
655ff266 LD	30	m25p80@0 {
	31	compatible = "atmel,at25df321a";
	32	spi-max-frequency = <50000000>;
	33	reg = <0>;
	34	};
	35	};
	36
27a96a03 BS	37	ssc0: ssc@f0008000 {
	38	atmel,clk-from-rk-pin;
	39	};
	40
655ff266 LD	41	/*
	42	* i2c0 conflicts with ISI:
	43	* disable it to allow the use of ISI
	44	* can not enable audio when i2c0 disabled
	45	*/
	46	i2c0: i2c@f0014000 {
	47	wm8904: wm8904@1a {
	48	compatible = "wm8904";
	49	reg = <0x1a>;
18f44d7b BS	50	clocks = <&pck0>;
18f44d7b BS	51	clock-names = "mclk";
655ff266 LD	52	};
	53	};
	54
	55	usart1: serial@f0020000 {
fe855dbf	56	dmas = <0>, <0>; /* Do not use DMA for usart1 */
655ff266 LD	57	pinctrl-names = "default";
	58	pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
	59	status = "okay";
	60	};
	61
	62	isi: isi@f0034000 {
	63	pinctrl-names = "default";
	64	pinctrl-0 = <&pinctrl_isi &pinctrl_isi_pck_as_mck &pinctrl_isi_power &pinctrl_isi_reset>;
	65	};
	66
	67	mmc1: mmc@f8000000 {
	68	pinctrl-names = "default";
	69	pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
	70	status = "okay";
	71	slot@0 {
	72	reg = <0>;
	73	bus-width = <4>;
92f8629b	74	cd-gpios = <&pioD 18 GPIO_ACTIVE_HIGH>;
655ff266 LD	75	};
	76	};
	77
	78	adc0: adc@f8018000 {
	79	pinctrl-names = "default";
	80	pinctrl-0 = <
	81	&pinctrl_adc0_adtrg
	82	&pinctrl_adc0_ad0
	83	&pinctrl_adc0_ad1
	84	&pinctrl_adc0_ad2
	85	&pinctrl_adc0_ad3
	86	&pinctrl_adc0_ad4
	87	>;
	88	status = "okay";
	89	};
	90
	91	macb1: ethernet@f802c000 {
	92	phy-mode = "rmii";
8c038e7e BB	93
	94	#address-cells = <1>;
	95	#size-cells = <0>;
a3a975b1	96	phy0: ethernet-phy@1 {
8c038e7e BB	97	interrupt-parent = <&pioE>;
	98	interrupts = <30 IRQ_TYPE_EDGE_FALLING>;
	99	reg = <1>;
	100	};
655ff266 LD	101	};
	102
	103	pinctrl@fffff200 {
	104	board {
	105	pinctrl_mmc0_cd: mmc0_cd {
	106	atmel,pins =
c9d0f317	107	<AT91_PIOD 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD17 GPIO with pullup deglitch */
655ff266 LD	108	};
	109
	110	pinctrl_mmc1_cd: mmc1_cd {
	111	atmel,pins =
c9d0f317	112	<AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD18 GPIO with pullup deglitch */
655ff266 LD	113	};
	114
	115	pinctrl_pck0_as_audio_mck: pck0_as_audio_mck {
	116	atmel,pins =
c9d0f317	117	<AT91_PIOD 30 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PD30 periph B */
655ff266 LD	118	};
	119
	120	pinctrl_isi_reset: isi_reset-0 {
	121	atmel,pins =
c9d0f317	122	<AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE24 gpio */
655ff266 LD	123	};
	124
	125	pinctrl_isi_power: isi_power-0 {
	126	atmel,pins =
c9d0f317	127	<AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE29 gpio */
655ff266 LD	128	};
	129
	130	pinctrl_usba_vbus: usba_vbus {
	131	atmel,pins =
c9d0f317	132	<AT91_PIOD 29 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PD29 GPIO with deglitch */
655ff266 LD	133	};
	134	};
	135	};
	136
	137	dbgu: serial@ffffee00 {
fe855dbf	138	dmas = <0>, <0>; /* Do not use DMA for dbgu */
655ff266 LD	139	status = "okay";
	140	};
	141
	142	watchdog@fffffe40 {
	143	status = "okay";
	144	};
	145	};
	146
	147	usb0: gadget@00500000 {
92f8629b	148	atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
655ff266 LD	149	pinctrl-names = "default";
	150	pinctrl-0 = <&pinctrl_usba_vbus>;
	151	status = "okay";
	152	};
	153
	154	usb1: ohci@00600000 {
	155	num-ports = <3>;
92f8629b JCPV	156	atmel,vbus-gpio = <&pioD 25 GPIO_ACTIVE_HIGH
	157	&pioD 26 GPIO_ACTIVE_LOW
	158	&pioD 27 GPIO_ACTIVE_LOW
655ff266 LD	159	>;
	160	status = "okay";
	161	};
	162
	163	usb2: ehci@00700000 {
	164	status = "okay";
	165	};
	166	};
	167
	168	sound {
469bbf0a	169	compatible = "atmel,asoc-wm8904";
655ff266 LD	170	pinctrl-names = "default";
	171	pinctrl-0 = <&pinctrl_pck0_as_audio_mck>;
	172
	173	atmel,model = "wm8904 @ SAMA5D3EK";
	174	atmel,audio-routing =
	175	"Headphone Jack", "HPOUTL",
	176	"Headphone Jack", "HPOUTR",
	177	"IN2L", "Line In Jack",
	178	"IN2R", "Line In Jack",
7a61fb07	179	"MICBIAS", "IN1L",
655ff266 LD	180	"IN1L", "Mic";
	181
	182	atmel,ssc-controller = <&ssc0>;
	183	atmel,audio-codec = <&wm8904>;
208ec6ff BS	184
208ec6ff BS	185	status = "disabled";
655ff266 LD	186	};
655ff266 LD	187	};