Commit | Line | Data |
---|---|---|
6af7fd88 LJ |
1 | /* |
2 | * Copyright 2012 ST-Ericsson AB | |
3 | * | |
4 | * The code contained herein is licensed under the GNU General Public | |
5 | * License. You may obtain a copy of the GNU General Public License | |
6 | * Version 2 or later at the following locations: | |
7 | * | |
8 | * http://www.opensource.org/licenses/gpl-license.html | |
9 | * http://www.gnu.org/copyleft/gpl.html | |
10 | */ | |
11 | ||
2ce05a14 | 12 | #include "ste-dbx5x0.dtsi" |
83200629 | 13 | #include "ste-href-ab8500.dtsi" |
2ce05a14 | 14 | #include "ste-href.dtsi" |
6af7fd88 LJ |
15 | |
16 | / { | |
d1b8bfa3 | 17 | model = "ST-Ericsson HREF (v60+) platform with Device Tree"; |
79b40753 | 18 | compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500"; |
6b8db132 | 19 | |
b1ba1439 | 20 | soc { |
7127c57f LJ |
21 | // External Micro SD slot |
22 | sdi0_per1@80126000 { | |
bf7a9b6f | 23 | cd-gpios = <&gpio2 31 0x4>; // 95 |
7127c57f | 24 | }; |
1e662353 | 25 | |
a1ab5e4c UH |
26 | vmmci: regulator-gpio { |
27 | gpios = <&gpio0 5 0x4>; | |
28 | enable-gpio = <&gpio5 9 0x4>; | |
29 | }; | |
30 | ||
1e662353 | 31 | pinctrl { |
7ab05bd1 LW |
32 | /* |
33 | * Set this up using hogs, as time goes by and as seems fit, these | |
34 | * can be moved over to being controlled by respective device. | |
35 | */ | |
1c850e4a | 36 | pinctrl-names = "default"; |
7ab05bd1 | 37 | pinctrl-0 = <&ipgpio_hrefv60_mode>, |
7ab05bd1 LW |
38 | <&etm_hrefv60_mode>, |
39 | <&nahj_hrefv60_mode>, | |
40 | <&nfc_hrefv60_mode>, | |
41 | <&force_hrefv60_mode>, | |
42 | <&dipro_hrefv60_mode>, | |
43 | <&vaudio_hf_hrefv60_mode>, | |
44 | <&gbf_hrefv60_mode>, | |
45 | <&hdtv_hrefv60_mode>, | |
46 | <&touch_hrefv60_mode>; | |
1c850e4a | 47 | |
1e662353 LW |
48 | sdi0 { |
49 | /* SD card detect GPIO pin, extend default state */ | |
50 | sdi0_default_mode: sdi0_default { | |
51 | default_hrefv60_cfg1 { | |
52 | ste,pins = "GPIO95_E8"; | |
53 | ste,config = <&gpio_in_pu>; | |
54 | }; | |
55 | }; | |
56 | }; | |
1c850e4a LW |
57 | ipgpio { |
58 | /* | |
59 | * XENON Flashgun on image processor GPIO (controlled from image | |
60 | * processor firmware), mux in these image processor GPIO lines 0 | |
61 | * (XENON_FLASH_ID), 1 (XENON_READY) and there is an assistant | |
62 | * LED on IP GPIO 4 (XENON_EN2) on altfunction C, that need bias | |
63 | * from GPIO21 so pull up 0, 1 and drive 4 and GPIO21 low as output. | |
64 | */ | |
65 | ipgpio_hrefv60_mode: ipgpio_hrefv60 { | |
66 | hrefv60_mux { | |
67 | ste,function = "ipgpio"; | |
68 | ste,pins = "ipgpio0_c_1", "ipgpio1_c_1", "ipgpio4_c_1"; | |
69 | }; | |
70 | hrefv60_cfg1 { | |
71 | ste,pins = "GPIO6_AF6", "GPIO7_AG5"; | |
72 | ste,config = <&in_pu>; | |
73 | }; | |
74 | hrefv60_cfg2 { | |
75 | ste,pins = "GPIO21_AB3"; | |
76 | ste,config = <&gpio_out_lo>; | |
77 | }; | |
78 | hrefv60_cfg3 { | |
79 | ste,pins = "GPIO64_F3"; | |
80 | ste,config = <&out_lo>; | |
81 | }; | |
7ab05bd1 LW |
82 | }; |
83 | }; | |
7ab05bd1 LW |
84 | etm { |
85 | /* | |
86 | * Drive D19-D23 for the ETM PTM trace interface low, | |
87 | * (presumably pins are unconnected therefore grounded here, | |
88 | * the "other alt C1" setting enables these pins) | |
89 | */ | |
90 | etm_hrefv60_mode: etm_hrefv60 { | |
91 | hrefv60_cfg1 { | |
92 | ste,pins = | |
93 | "GPIO70_G5", | |
94 | "GPIO71_G4", | |
95 | "GPIO72_H4", | |
96 | "GPIO73_H3", | |
97 | "GPIO74_J3"; | |
98 | ste,config = <&gpio_out_lo>; | |
99 | }; | |
1c850e4a LW |
100 | }; |
101 | }; | |
7ab05bd1 LW |
102 | nahj { |
103 | nahj_hrefv60_mode: nahj_hrefv60 { | |
104 | /* NAHJ CTRL on GPIO76 to low, CTRL_INV on GPIO216 to high */ | |
105 | hrefv60_cfg1 { | |
106 | ste,pins = "GPIO76_J2"; | |
107 | ste,config = <&gpio_out_lo>; | |
108 | }; | |
109 | hrefv60_cfg2 { | |
110 | ste,pins = "GPIO216_AG12"; | |
111 | ste,config = <&gpio_out_hi>; | |
112 | }; | |
113 | }; | |
114 | }; | |
115 | nfc { | |
116 | nfc_hrefv60_mode: nfc_hrefv60 { | |
117 | /* NFC ENA and RESET to low, pulldown IRQ line */ | |
118 | hrefv60_cfg1 { | |
119 | ste,pins = | |
120 | "GPIO77_H1", /* NFC_ENA */ | |
121 | "GPIO142_C11"; /* NFC_RESET */ | |
122 | ste,config = <&gpio_out_lo>; | |
123 | }; | |
124 | hrefv60_cfg2 { | |
125 | ste,pins = "GPIO144_B13"; /* NFC_IRQ */ | |
126 | ste,config = <&gpio_in_pd>; | |
127 | }; | |
128 | }; | |
129 | }; | |
130 | force { | |
131 | force_hrefv60_mode: force_hrefv60 { | |
132 | hrefv60_cfg1 { | |
133 | ste,pins = "GPIO91_B6"; /* FORCE_SENSING_INT */ | |
134 | ste,config = <&gpio_in_pu>; | |
135 | }; | |
136 | hrefv60_cfg2 { | |
137 | ste,pins = | |
138 | "GPIO92_D6", /* FORCE_SENSING_RST */ | |
139 | "GPIO97_D9"; /* FORCE_SENSING_WU */ | |
140 | ste,config = <&gpio_out_lo>; | |
141 | }; | |
142 | }; | |
143 | }; | |
144 | dipro { | |
145 | dipro_hrefv60_mode: dipro_hrefv60 { | |
146 | hrefv60_cfg1 { | |
147 | ste,pins = "GPIO139_C9"; /* DIPRO_INT */ | |
148 | ste,config = <&gpio_in_pu>; | |
149 | }; | |
150 | }; | |
151 | }; | |
152 | vaudio_hf { | |
153 | vaudio_hf_hrefv60_mode: vaudio_hf_hrefv60 { | |
154 | /* Audio Amplifier HF enable GPIO */ | |
155 | hrefv60_cfg1 { | |
156 | ste,pins = "GPIO149_B14"; /* VAUDIO_HF_EN, enable MAX8968 */ | |
157 | ste,config = <&gpio_out_hi>; | |
158 | }; | |
159 | }; | |
160 | }; | |
161 | gbf { | |
162 | gbf_hrefv60_mode: gbf_hrefv60 { | |
163 | /* | |
164 | * GBF (GPS, Bluetooth, FM-radio) interface, | |
165 | * pull low to reset state | |
166 | */ | |
167 | hrefv60_cfg1 { | |
168 | ste,pins = "GPIO171_D23"; /* GBF_ENA_RESET */ | |
169 | ste,config = <&gpio_out_lo>; | |
170 | }; | |
171 | }; | |
172 | }; | |
173 | hdtv { | |
174 | hdtv_hrefv60_mode: hdtv_hrefv60 { | |
175 | /* MSP : HDTV INTERFACE GPIO line */ | |
176 | hrefv60_cfg1 { | |
177 | ste,pins = "GPIO192_AJ27"; | |
178 | ste,config = <&gpio_in_pd>; | |
179 | }; | |
180 | }; | |
181 | }; | |
182 | touch { | |
183 | touch_hrefv60_mode: touch_hrefv60 { | |
184 | /* | |
185 | * Touch screen uses GPIO 143 for RST1, GPIO 146 for RST2 and | |
186 | * GPIO 67 for interrupts. Pull-up the IRQ line and drive both | |
187 | * reset signals low. | |
188 | */ | |
189 | hrefv60_cfg1 { | |
190 | ste,pins = "GPIO143_D12", "GPIO146_D13"; | |
191 | ste,config = <&gpio_out_lo>; | |
192 | }; | |
193 | hrefv60_cfg2 { | |
194 | ste,pins = "GPIO67_G2"; | |
195 | ste,config = <&gpio_in_pu>; | |
196 | }; | |
197 | }; | |
198 | }; | |
17afa716 LW |
199 | mcde { |
200 | lcd_hrefv60_mode: lcd_hrefv60 { | |
201 | /* | |
202 | * Display Interface 1 uses GPIO 65 for RST (reset). | |
203 | * Display Interface 2 uses GPIO 66 for RST (reset). | |
204 | * Drive DISP1 reset high (not reset), driver DISP2 reset low (reset) | |
205 | */ | |
206 | hrefv60_cfg1 { | |
207 | ste,pins ="GPIO65_F1"; | |
208 | ste,config = <&gpio_out_hi>; | |
209 | }; | |
210 | hrefv60_cfg2 { | |
211 | ste,pins ="GPIO66_G3"; | |
212 | ste,config = <&gpio_out_lo>; | |
213 | }; | |
214 | }; | |
215 | }; | |
1e662353 | 216 | }; |
cbebba7d | 217 | }; |
6af7fd88 | 218 | }; |