Commit | Line | Data |
---|---|---|
53d02858 TV |
1 | #include <dt-bindings/input/input.h> |
2 | #include "tegra124.dtsi" | |
3 | ||
4 | / { | |
5 | aliases { | |
6 | rtc0 = "/i2c@0,7000d000/pmic@40"; | |
7 | rtc1 = "/rtc@0,7000e000"; | |
8 | serial0 = &uarta; | |
9 | }; | |
10 | ||
11 | memory { | |
12 | reg = <0x0 0x80000000 0x0 0x80000000>; | |
13 | }; | |
14 | ||
15 | host1x@0,50000000 { | |
16 | hdmi@0,54280000 { | |
17 | status = "okay"; | |
18 | ||
19 | vdd-supply = <&vdd_3v3_hdmi>; | |
20 | pll-supply = <&vdd_hdmi_pll>; | |
21 | hdmi-supply = <&vdd_5v0_hdmi>; | |
22 | ||
23 | nvidia,ddc-i2c-bus = <&hdmi_ddc>; | |
24 | nvidia,hpd-gpio = | |
25 | <&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>; | |
26 | }; | |
27 | ||
28 | sor@0,54540000 { | |
29 | status = "okay"; | |
30 | ||
31 | nvidia,dpaux = <&dpaux>; | |
32 | nvidia,panel = <&panel>; | |
33 | }; | |
34 | ||
35 | dpaux@0,545c0000 { | |
36 | vdd-supply = <&vdd_3v3_panel>; | |
37 | status = "okay"; | |
38 | }; | |
39 | }; | |
40 | ||
41 | serial@0,70006000 { | |
42 | /* Debug connector on the bottom of the board near SD card. */ | |
43 | status = "okay"; | |
44 | }; | |
45 | ||
46 | pwm@0,7000a000 { | |
47 | status = "okay"; | |
48 | }; | |
49 | ||
50 | i2c@0,7000c000 { | |
51 | status = "okay"; | |
52 | clock-frequency = <100000>; | |
53 | ||
54 | acodec: audio-codec@10 { | |
55 | compatible = "maxim,max98090"; | |
56 | reg = <0x10>; | |
57 | interrupt-parent = <&gpio>; | |
58 | interrupts = <TEGRA_GPIO(H, 4) GPIO_ACTIVE_HIGH>; | |
59 | }; | |
60 | ||
61 | temperature-sensor@4c { | |
62 | compatible = "ti,tmp451"; | |
63 | reg = <0x4c>; | |
64 | interrupt-parent = <&gpio>; | |
65 | interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>; | |
66 | ||
67 | #thermal-sensor-cells = <1>; | |
68 | }; | |
69 | }; | |
70 | ||
71 | i2c@0,7000c400 { | |
72 | status = "okay"; | |
73 | clock-frequency = <100000>; | |
a0b9c1cb TV |
74 | |
75 | trackpad@15 { | |
76 | compatible = "elan,ekth3000"; | |
77 | reg = <0x15>; | |
78 | interrupt-parent = <&gpio>; | |
79 | interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_EDGE_FALLING>; | |
80 | wakeup-source; | |
81 | }; | |
53d02858 TV |
82 | }; |
83 | ||
84 | i2c@0,7000c500 { | |
85 | status = "okay"; | |
86 | clock-frequency = <400000>; | |
87 | ||
88 | tpm@20 { | |
89 | compatible = "infineon,slb9645tt"; | |
90 | reg = <0x20>; | |
91 | }; | |
92 | }; | |
93 | ||
94 | hdmi_ddc: i2c@0,7000c700 { | |
95 | status = "okay"; | |
96 | clock-frequency = <100000>; | |
97 | }; | |
98 | ||
99 | i2c@0,7000d000 { | |
100 | status = "okay"; | |
101 | clock-frequency = <400000>; | |
102 | ||
103 | pmic: pmic@40 { | |
104 | compatible = "ams,as3722"; | |
105 | reg = <0x40>; | |
106 | interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>; | |
107 | ||
108 | ams,system-power-controller; | |
109 | ||
110 | #interrupt-cells = <2>; | |
111 | interrupt-controller; | |
112 | ||
113 | gpio-controller; | |
114 | #gpio-cells = <2>; | |
115 | ||
116 | pinctrl-names = "default"; | |
117 | pinctrl-0 = <&as3722_default>; | |
118 | ||
119 | as3722_default: pinmux { | |
120 | gpio0 { | |
121 | pins = "gpio0"; | |
122 | function = "gpio"; | |
123 | bias-pull-down; | |
124 | }; | |
125 | ||
126 | gpio1 { | |
127 | pins = "gpio1"; | |
128 | function = "gpio"; | |
129 | bias-pull-up; | |
130 | }; | |
131 | ||
132 | gpio2_4_7 { | |
133 | pins = "gpio2", "gpio4", "gpio7"; | |
134 | function = "gpio"; | |
135 | bias-pull-up; | |
136 | }; | |
137 | ||
138 | gpio3_6 { | |
139 | pins = "gpio3", "gpio6"; | |
140 | bias-high-impedance; | |
141 | }; | |
142 | ||
143 | gpio5 { | |
144 | pins = "gpio5"; | |
145 | function = "clk32k-out"; | |
146 | bias-pull-down; | |
147 | }; | |
148 | }; | |
149 | ||
150 | regulators { | |
151 | vsup-sd2-supply = <&vdd_5v0_sys>; | |
152 | vsup-sd3-supply = <&vdd_5v0_sys>; | |
153 | vsup-sd4-supply = <&vdd_5v0_sys>; | |
154 | vsup-sd5-supply = <&vdd_5v0_sys>; | |
155 | vin-ldo0-supply = <&vdd_1v35_lp0>; | |
156 | vin-ldo1-6-supply = <&vdd_3v3_run>; | |
157 | vin-ldo2-5-7-supply = <&vddio_1v8>; | |
158 | vin-ldo3-4-supply = <&vdd_3v3_sys>; | |
159 | vin-ldo9-10-supply = <&vdd_5v0_sys>; | |
160 | vin-ldo11-supply = <&vdd_3v3_run>; | |
161 | ||
9a0baee9 | 162 | vdd_cpu: sd0 { |
53d02858 TV |
163 | regulator-name = "+VDD_CPU_AP"; |
164 | regulator-min-microvolt = <700000>; | |
165 | regulator-max-microvolt = <1350000>; | |
166 | regulator-min-microamp = <3500000>; | |
167 | regulator-max-microamp = <3500000>; | |
168 | regulator-always-on; | |
169 | regulator-boot-on; | |
170 | ams,ext-control = <2>; | |
171 | }; | |
172 | ||
173 | sd1 { | |
174 | regulator-name = "+VDD_CORE"; | |
175 | regulator-min-microvolt = <700000>; | |
176 | regulator-max-microvolt = <1350000>; | |
177 | regulator-min-microamp = <2500000>; | |
178 | regulator-max-microamp = <4000000>; | |
179 | regulator-always-on; | |
180 | regulator-boot-on; | |
181 | ams,ext-control = <1>; | |
182 | }; | |
183 | ||
184 | vdd_1v35_lp0: sd2 { | |
185 | regulator-name = "+1.35V_LP0(sd2)"; | |
186 | regulator-min-microvolt = <1350000>; | |
187 | regulator-max-microvolt = <1350000>; | |
188 | regulator-always-on; | |
189 | regulator-boot-on; | |
190 | }; | |
191 | ||
192 | sd3 { | |
193 | regulator-name = "+1.35V_LP0(sd3)"; | |
194 | regulator-min-microvolt = <1350000>; | |
195 | regulator-max-microvolt = <1350000>; | |
196 | regulator-always-on; | |
197 | regulator-boot-on; | |
198 | }; | |
199 | ||
200 | vdd_1v05_run: sd4 { | |
201 | regulator-name = "+1.05V_RUN"; | |
202 | regulator-min-microvolt = <1050000>; | |
203 | regulator-max-microvolt = <1050000>; | |
204 | }; | |
205 | ||
206 | vddio_1v8: sd5 { | |
207 | regulator-name = "+1.8V_VDDIO"; | |
208 | regulator-min-microvolt = <1800000>; | |
209 | regulator-max-microvolt = <1800000>; | |
53d02858 TV |
210 | regulator-always-on; |
211 | }; | |
212 | ||
213 | sd6 { | |
214 | regulator-name = "+VDD_GPU_AP"; | |
215 | regulator-min-microvolt = <650000>; | |
216 | regulator-max-microvolt = <1200000>; | |
217 | regulator-min-microamp = <3500000>; | |
218 | regulator-max-microamp = <3500000>; | |
219 | regulator-boot-on; | |
220 | regulator-always-on; | |
221 | }; | |
222 | ||
223 | ldo0 { | |
224 | regulator-name = "+1.05V_RUN_AVDD"; | |
225 | regulator-min-microvolt = <1050000>; | |
226 | regulator-max-microvolt = <1050000>; | |
227 | regulator-boot-on; | |
228 | regulator-always-on; | |
229 | ams,ext-control = <1>; | |
230 | }; | |
231 | ||
232 | ldo1 { | |
233 | regulator-name = "+1.8V_RUN_CAM"; | |
234 | regulator-min-microvolt = <1800000>; | |
235 | regulator-max-microvolt = <1800000>; | |
236 | }; | |
237 | ||
238 | ldo2 { | |
239 | regulator-name = "+1.2V_GEN_AVDD"; | |
240 | regulator-min-microvolt = <1200000>; | |
241 | regulator-max-microvolt = <1200000>; | |
242 | regulator-boot-on; | |
243 | regulator-always-on; | |
244 | }; | |
245 | ||
246 | ldo3 { | |
247 | regulator-name = "+1.00V_LP0_VDD_RTC"; | |
248 | regulator-min-microvolt = <1000000>; | |
249 | regulator-max-microvolt = <1000000>; | |
250 | regulator-boot-on; | |
251 | regulator-always-on; | |
252 | ams,enable-tracking; | |
253 | }; | |
254 | ||
255 | vdd_run_cam: ldo4 { | |
256 | regulator-name = "+3.3V_RUN_CAM"; | |
257 | regulator-min-microvolt = <2800000>; | |
258 | regulator-max-microvolt = <2800000>; | |
259 | }; | |
260 | ||
261 | ldo5 { | |
262 | regulator-name = "+1.2V_RUN_CAM_FRONT"; | |
263 | regulator-min-microvolt = <1200000>; | |
264 | regulator-max-microvolt = <1200000>; | |
265 | }; | |
266 | ||
267 | vddio_sdmmc3: ldo6 { | |
268 | regulator-name = "+VDDIO_SDMMC3"; | |
269 | regulator-min-microvolt = <1800000>; | |
270 | regulator-max-microvolt = <3300000>; | |
271 | }; | |
272 | ||
273 | ldo7 { | |
274 | regulator-name = "+1.05V_RUN_CAM_REAR"; | |
275 | regulator-min-microvolt = <1050000>; | |
276 | regulator-max-microvolt = <1050000>; | |
277 | }; | |
278 | ||
279 | ldo9 { | |
280 | regulator-name = "+2.8V_RUN_TOUCH"; | |
281 | regulator-min-microvolt = <2800000>; | |
282 | regulator-max-microvolt = <2800000>; | |
283 | }; | |
284 | ||
285 | ldo10 { | |
286 | regulator-name = "+2.8V_RUN_CAM_AF"; | |
287 | regulator-min-microvolt = <2800000>; | |
288 | regulator-max-microvolt = <2800000>; | |
289 | }; | |
290 | ||
291 | ldo11 { | |
292 | regulator-name = "+1.8V_RUN_VPP_FUSE"; | |
293 | regulator-min-microvolt = <1800000>; | |
294 | regulator-max-microvolt = <1800000>; | |
295 | }; | |
296 | }; | |
297 | }; | |
298 | }; | |
299 | ||
300 | spi@0,7000d400 { | |
301 | status = "okay"; | |
302 | ||
303 | cros_ec: cros-ec@0 { | |
304 | compatible = "google,cros-ec-spi"; | |
305 | spi-max-frequency = <3000000>; | |
306 | interrupt-parent = <&gpio>; | |
307 | interrupts = <TEGRA_GPIO(C, 7) IRQ_TYPE_LEVEL_LOW>; | |
308 | reg = <0>; | |
309 | ||
310 | google,cros-ec-spi-msg-delay = <2000>; | |
311 | ||
312 | i2c-tunnel { | |
313 | compatible = "google,cros-ec-i2c-tunnel"; | |
314 | #address-cells = <1>; | |
315 | #size-cells = <0>; | |
316 | ||
317 | google,remote-bus = <0>; | |
318 | ||
319 | charger: bq24735@9 { | |
320 | compatible = "ti,bq24735"; | |
321 | reg = <0x9>; | |
322 | interrupt-parent = <&gpio>; | |
323 | interrupts = <TEGRA_GPIO(J, 0) | |
324 | GPIO_ACTIVE_HIGH>; | |
325 | ti,ac-detect-gpios = <&gpio | |
326 | TEGRA_GPIO(J, 0) | |
327 | GPIO_ACTIVE_HIGH>; | |
328 | }; | |
329 | ||
330 | battery: sbs-battery@b { | |
331 | compatible = "sbs,sbs-battery"; | |
332 | reg = <0xb>; | |
333 | sbs,i2c-retry-count = <2>; | |
334 | sbs,poll-retry-count = <10>; | |
335 | power-supplies = <&charger>; | |
336 | }; | |
337 | }; | |
338 | }; | |
339 | }; | |
340 | ||
341 | spi@0,7000da00 { | |
342 | status = "okay"; | |
343 | spi-max-frequency = <25000000>; | |
344 | ||
345 | flash@0 { | |
346 | compatible = "winbond,w25q32dw"; | |
97e147e8 | 347 | spi-max-frequency = <25000000>; |
53d02858 TV |
348 | reg = <0>; |
349 | }; | |
350 | }; | |
351 | ||
352 | pmc@0,7000e400 { | |
353 | nvidia,invert-interrupt; | |
354 | nvidia,suspend-mode = <0>; | |
355 | nvidia,cpu-pwr-good-time = <500>; | |
356 | nvidia,cpu-pwr-off-time = <300>; | |
357 | nvidia,core-pwr-good-time = <641 3845>; | |
358 | nvidia,core-pwr-off-time = <61036>; | |
359 | nvidia,core-power-req-active-high; | |
360 | nvidia,sys-clock-req-active-high; | |
361 | }; | |
362 | ||
363 | hda@0,70030000 { | |
364 | status = "okay"; | |
365 | }; | |
366 | ||
1d1690b8 TV |
367 | sdhci0_pwrseq: sdhci0_pwrseq { |
368 | compatible = "mmc-pwrseq-simple"; | |
369 | ||
370 | reset-gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_LOW>; | |
371 | }; | |
372 | ||
53d02858 TV |
373 | sdhci@0,700b0000 { /* WiFi/BT on this bus */ |
374 | status = "okay"; | |
53d02858 TV |
375 | bus-width = <4>; |
376 | no-1-8-v; | |
377 | non-removable; | |
1d1690b8 TV |
378 | mmc-pwrseq = <&sdhci0_pwrseq>; |
379 | vmmc-supply = <&vdd_3v3_lp0>; | |
380 | vqmmc-supply = <&vddio_1v8>; | |
160b2dd7 | 381 | keep-power-in-suspend; |
53d02858 TV |
382 | }; |
383 | ||
384 | sdhci@0,700b0400 { /* SD Card on this bus */ | |
385 | status = "okay"; | |
386 | cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>; | |
387 | power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>; | |
388 | bus-width = <4>; | |
389 | no-1-8-v; | |
390 | vqmmc-supply = <&vddio_sdmmc3>; | |
391 | }; | |
392 | ||
393 | sdhci@0,700b0600 { /* eMMC on this bus */ | |
394 | status = "okay"; | |
395 | bus-width = <8>; | |
396 | no-1-8-v; | |
397 | non-removable; | |
398 | }; | |
399 | ||
9a0baee9 JH |
400 | /* CPU DFLL clock */ |
401 | clock@0,70110000 { | |
80373d37 | 402 | status = "disabled"; |
9a0baee9 JH |
403 | vdd-cpu-supply = <&vdd_cpu>; |
404 | nvidia,i2c-fs-rate = <400000>; | |
405 | }; | |
406 | ||
53d02858 TV |
407 | ahub@0,70300000 { |
408 | i2s@0,70301100 { | |
409 | status = "okay"; | |
410 | }; | |
411 | }; | |
412 | ||
413 | usb@0,7d000000 { /* Rear external USB port. */ | |
414 | status = "okay"; | |
415 | }; | |
416 | ||
417 | usb-phy@0,7d000000 { | |
418 | status = "okay"; | |
419 | vbus-supply = <&vdd_usb1_vbus>; | |
420 | }; | |
421 | ||
422 | usb@0,7d004000 { /* Internal webcam. */ | |
423 | status = "okay"; | |
424 | }; | |
425 | ||
426 | usb-phy@0,7d004000 { | |
427 | status = "okay"; | |
428 | vbus-supply = <&vdd_run_cam>; | |
429 | }; | |
430 | ||
431 | usb@0,7d008000 { /* Left external USB port. */ | |
432 | status = "okay"; | |
433 | }; | |
434 | ||
435 | usb-phy@0,7d008000 { | |
436 | status = "okay"; | |
437 | vbus-supply = <&vdd_usb3_vbus>; | |
438 | }; | |
439 | ||
440 | backlight: backlight { | |
441 | compatible = "pwm-backlight"; | |
442 | ||
443 | enable-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>; | |
444 | power-supply = <&vdd_led>; | |
445 | pwms = <&pwm 1 1000000>; | |
446 | ||
447 | default-brightness-level = <224>; | |
448 | brightness-levels = | |
449 | < 0 1 2 3 4 5 6 7 | |
450 | 8 9 10 11 12 13 14 15 | |
451 | 16 17 18 19 20 21 22 23 | |
452 | 24 25 26 27 28 29 30 31 | |
453 | 32 33 34 35 36 37 38 39 | |
454 | 40 41 42 43 44 45 46 47 | |
455 | 48 49 50 51 52 53 54 55 | |
456 | 56 57 58 59 60 61 62 63 | |
457 | 64 65 66 67 68 69 70 71 | |
458 | 72 73 74 75 76 77 78 79 | |
459 | 80 81 82 83 84 85 86 87 | |
460 | 88 89 90 91 92 93 94 95 | |
461 | 96 97 98 99 100 101 102 103 | |
462 | 104 105 106 107 108 109 110 111 | |
463 | 112 113 114 115 116 117 118 119 | |
464 | 120 121 122 123 124 125 126 127 | |
465 | 128 129 130 131 132 133 134 135 | |
466 | 136 137 138 139 140 141 142 143 | |
467 | 144 145 146 147 148 149 150 151 | |
468 | 152 153 154 155 156 157 158 159 | |
469 | 160 161 162 163 164 165 166 167 | |
470 | 168 169 170 171 172 173 174 175 | |
471 | 176 177 178 179 180 181 182 183 | |
472 | 184 185 186 187 188 189 190 191 | |
473 | 192 193 194 195 196 197 198 199 | |
474 | 200 201 202 203 204 205 206 207 | |
475 | 208 209 210 211 212 213 214 215 | |
476 | 216 217 218 219 220 221 222 223 | |
477 | 224 225 226 227 228 229 230 231 | |
478 | 232 233 234 235 236 237 238 239 | |
479 | 240 241 242 243 244 245 246 247 | |
480 | 248 249 250 251 252 253 254 255 | |
481 | 256>; | |
482 | }; | |
483 | ||
484 | clocks { | |
485 | compatible = "simple-bus"; | |
486 | #address-cells = <1>; | |
487 | #size-cells = <0>; | |
488 | ||
489 | clk32k_in: clock@0 { | |
490 | compatible = "fixed-clock"; | |
491 | reg = <0>; | |
492 | #clock-cells = <0>; | |
493 | clock-frequency = <32768>; | |
494 | }; | |
495 | }; | |
496 | ||
9a0baee9 JH |
497 | cpus { |
498 | cpu@0 { | |
499 | vdd-cpu-supply = <&vdd_cpu>; | |
500 | }; | |
501 | }; | |
502 | ||
53d02858 TV |
503 | gpio-keys { |
504 | compatible = "gpio-keys"; | |
505 | ||
506 | lid { | |
507 | label = "Lid"; | |
508 | gpios = <&gpio TEGRA_GPIO(R, 4) GPIO_ACTIVE_LOW>; | |
509 | linux,input-type = <5>; | |
510 | linux,code = <KEY_RESERVED>; | |
511 | debounce-interval = <1>; | |
512 | gpio-key,wakeup; | |
513 | }; | |
514 | ||
515 | power { | |
516 | label = "Power"; | |
517 | gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>; | |
518 | linux,code = <KEY_POWER>; | |
519 | debounce-interval = <30>; | |
520 | gpio-key,wakeup; | |
521 | }; | |
522 | }; | |
523 | ||
524 | regulators { | |
525 | compatible = "simple-bus"; | |
526 | #address-cells = <1>; | |
527 | #size-cells = <0>; | |
528 | ||
529 | vdd_mux: regulator@0 { | |
530 | compatible = "regulator-fixed"; | |
531 | reg = <0>; | |
532 | regulator-name = "+VDD_MUX"; | |
533 | regulator-min-microvolt = <12000000>; | |
534 | regulator-max-microvolt = <12000000>; | |
535 | regulator-always-on; | |
536 | regulator-boot-on; | |
537 | }; | |
538 | ||
539 | vdd_5v0_sys: regulator@1 { | |
540 | compatible = "regulator-fixed"; | |
541 | reg = <1>; | |
542 | regulator-name = "+5V_SYS"; | |
543 | regulator-min-microvolt = <5000000>; | |
544 | regulator-max-microvolt = <5000000>; | |
545 | regulator-always-on; | |
546 | regulator-boot-on; | |
547 | vin-supply = <&vdd_mux>; | |
548 | }; | |
549 | ||
550 | vdd_3v3_sys: regulator@2 { | |
551 | compatible = "regulator-fixed"; | |
552 | reg = <2>; | |
553 | regulator-name = "+3.3V_SYS"; | |
554 | regulator-min-microvolt = <3300000>; | |
555 | regulator-max-microvolt = <3300000>; | |
556 | regulator-always-on; | |
557 | regulator-boot-on; | |
558 | vin-supply = <&vdd_mux>; | |
559 | }; | |
560 | ||
561 | vdd_3v3_run: regulator@3 { | |
562 | compatible = "regulator-fixed"; | |
563 | reg = <3>; | |
564 | regulator-name = "+3.3V_RUN"; | |
565 | regulator-min-microvolt = <3300000>; | |
566 | regulator-max-microvolt = <3300000>; | |
567 | regulator-always-on; | |
568 | regulator-boot-on; | |
569 | gpio = <&pmic 1 GPIO_ACTIVE_HIGH>; | |
570 | enable-active-high; | |
571 | vin-supply = <&vdd_3v3_sys>; | |
572 | }; | |
573 | ||
574 | vdd_3v3_hdmi: regulator@4 { | |
575 | compatible = "regulator-fixed"; | |
576 | reg = <4>; | |
577 | regulator-name = "+3.3V_AVDD_HDMI_AP_GATED"; | |
578 | regulator-min-microvolt = <3300000>; | |
579 | regulator-max-microvolt = <3300000>; | |
580 | vin-supply = <&vdd_3v3_run>; | |
581 | }; | |
582 | ||
583 | vdd_led: regulator@5 { | |
584 | compatible = "regulator-fixed"; | |
585 | reg = <5>; | |
586 | regulator-name = "+VDD_LED"; | |
587 | gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>; | |
588 | enable-active-high; | |
589 | vin-supply = <&vdd_mux>; | |
590 | }; | |
591 | ||
592 | vdd_5v0_ts: regulator@6 { | |
593 | compatible = "regulator-fixed"; | |
594 | reg = <6>; | |
595 | regulator-name = "+5V_VDD_TS_SW"; | |
596 | regulator-min-microvolt = <5000000>; | |
597 | regulator-max-microvolt = <5000000>; | |
598 | regulator-boot-on; | |
599 | gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>; | |
600 | enable-active-high; | |
601 | vin-supply = <&vdd_5v0_sys>; | |
602 | }; | |
603 | ||
604 | vdd_usb1_vbus: regulator@7 { | |
605 | compatible = "regulator-fixed"; | |
606 | reg = <7>; | |
607 | regulator-name = "+5V_USB_HS"; | |
608 | regulator-min-microvolt = <5000000>; | |
609 | regulator-max-microvolt = <5000000>; | |
610 | gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>; | |
611 | enable-active-high; | |
612 | gpio-open-drain; | |
613 | vin-supply = <&vdd_5v0_sys>; | |
614 | }; | |
615 | ||
616 | vdd_usb3_vbus: regulator@8 { | |
617 | compatible = "regulator-fixed"; | |
618 | reg = <8>; | |
619 | regulator-name = "+5V_USB_SS"; | |
620 | regulator-min-microvolt = <5000000>; | |
621 | regulator-max-microvolt = <5000000>; | |
622 | gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>; | |
623 | enable-active-high; | |
624 | gpio-open-drain; | |
625 | vin-supply = <&vdd_5v0_sys>; | |
626 | }; | |
627 | ||
628 | vdd_3v3_panel: regulator@9 { | |
629 | compatible = "regulator-fixed"; | |
630 | reg = <9>; | |
631 | regulator-name = "+3.3V_PANEL"; | |
632 | regulator-min-microvolt = <3300000>; | |
633 | regulator-max-microvolt = <3300000>; | |
634 | gpio = <&pmic 4 GPIO_ACTIVE_HIGH>; | |
635 | enable-active-high; | |
636 | vin-supply = <&vdd_3v3_run>; | |
637 | }; | |
638 | ||
639 | vdd_3v3_lp0: regulator@10 { | |
640 | compatible = "regulator-fixed"; | |
641 | reg = <10>; | |
642 | regulator-name = "+3.3V_LP0"; | |
643 | regulator-min-microvolt = <3300000>; | |
644 | regulator-max-microvolt = <3300000>; | |
645 | /* | |
646 | * TODO: find a way to wire this up with the USB EHCI | |
647 | * controllers so that it can be enabled on demand. | |
648 | */ | |
649 | regulator-always-on; | |
650 | gpio = <&pmic 2 GPIO_ACTIVE_HIGH>; | |
651 | enable-active-high; | |
652 | vin-supply = <&vdd_3v3_sys>; | |
653 | }; | |
654 | ||
655 | vdd_hdmi_pll: regulator@11 { | |
656 | compatible = "regulator-fixed"; | |
657 | reg = <11>; | |
658 | regulator-name = "+1.05V_RUN_AVDD_HDMI_PLL"; | |
659 | regulator-min-microvolt = <1050000>; | |
660 | regulator-max-microvolt = <1050000>; | |
661 | gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_LOW>; | |
662 | vin-supply = <&vdd_1v05_run>; | |
663 | }; | |
664 | ||
665 | vdd_5v0_hdmi: regulator@12 { | |
666 | compatible = "regulator-fixed"; | |
667 | reg = <12>; | |
668 | regulator-name = "+5V_HDMI_CON"; | |
669 | regulator-min-microvolt = <5000000>; | |
670 | regulator-max-microvolt = <5000000>; | |
671 | gpio = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>; | |
672 | enable-active-high; | |
673 | vin-supply = <&vdd_5v0_sys>; | |
674 | }; | |
675 | }; | |
676 | ||
677 | sound { | |
678 | nvidia,audio-routing = | |
679 | "Headphones", "HPR", | |
680 | "Headphones", "HPL", | |
681 | "Speakers", "SPKR", | |
682 | "Speakers", "SPKL", | |
683 | "Mic Jack", "MICBIAS", | |
684 | "DMICL", "Int Mic", | |
685 | "DMICR", "Int Mic", | |
686 | "IN34", "Mic Jack"; | |
687 | ||
688 | nvidia,i2s-controller = <&tegra_i2s1>; | |
689 | nvidia,audio-codec = <&acodec>; | |
690 | ||
691 | clocks = <&tegra_car TEGRA124_CLK_PLL_A>, | |
692 | <&tegra_car TEGRA124_CLK_PLL_A_OUT0>, | |
693 | <&tegra_car TEGRA124_CLK_EXTERN1>; | |
694 | clock-names = "pll_a", "pll_a_out0", "mclk"; | |
695 | ||
696 | nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(I, 7) GPIO_ACTIVE_HIGH>; | |
697 | nvidia,mic-det-gpios = | |
698 | <&gpio TEGRA_GPIO(R, 7) GPIO_ACTIVE_HIGH>; | |
699 | }; | |
1755de86 TV |
700 | |
701 | gpio-restart { | |
702 | compatible = "gpio-restart"; | |
703 | gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>; | |
704 | priority = <200>; | |
705 | }; | |
53d02858 TV |
706 | }; |
707 | ||
708 | #include "cros-ec-keyboard.dtsi" |