[deliverable/linux.git] / arch / cris / Kconfig

config MMU
	bool
	default y

config ZONE_DMA
	bool
	default y

config RWSEM_GENERIC_SPINLOCK
	bool
	default y

config RWSEM_XCHGADD_ALGORITHM
	bool

config ARCH_HAS_ILOG2_U32
	bool
	default n

config ARCH_HAS_ILOG2_U64
	bool
	default n

config GENERIC_HWEIGHT
	bool
	default y

config GENERIC_CALIBRATE_DELAY
	bool
	default y

config NO_IOPORT
	def_bool y

config FORCE_MAX_ZONEORDER
	int
	default 6

config CRIS
	bool
	default y
	select HAVE_IDE
	select GENERIC_ATOMIC64
	select HAVE_GENERIC_HARDIRQS
	select GENERIC_IRQ_SHOW
	select GENERIC_IOMAP
	select GENERIC_SMP_IDLE_THREAD if ETRAX_ARCH_V32
	select GENERIC_CMOS_UPDATE

config HZ
	int
	default 100

source "init/Kconfig"

source "kernel/Kconfig.freezer"

menu "General setup"

source "fs/Kconfig.binfmt"

config ETRAX_CMDLINE
	string "Kernel command line"
	default "root=/dev/mtdblock3"
	help
	  Pass additional commands to the kernel.

config ETRAX_WATCHDOG
	bool "Enable ETRAX watchdog"
	help
	  Enable the built-in watchdog timer support on ETRAX based embedded
	  network computers.

config ETRAX_WATCHDOG_NICE_DOGGY
	bool "Disable watchdog during Oops printouts"
	depends on ETRAX_WATCHDOG
	help
	  By enabling this you make sure that the watchdog does not bite while
	  printing oopses. Recommended for development systems but not for
	  production releases.

config ETRAX_FAST_TIMER
       bool "Enable ETRAX fast timer API"
       help
         This options enables the API to a fast timer implementation using
	 timer1 to get sub jiffie resolution timers (primarily one-shot
	 timers).
	 This is needed if CONFIG_ETRAX_SERIAL_FAST_TIMER is enabled.

config ETRAX_KMALLOCED_MODULES
	bool "Enable module allocation with kmalloc"
	help
	  Enable module allocation with kmalloc instead of vmalloc.

config OOM_REBOOT
       bool "Enable reboot at out of memory"

source "kernel/Kconfig.preempt"

source mm/Kconfig

endmenu

menu "Hardware setup"

choice
	prompt "Processor type"
	default ETRAX100LX

config ETRAX100LX
	bool "ETRAX-100LX-v1"
	select ARCH_USES_GETTIMEOFFSET
	help
	  Support version 1 of the ETRAX 100LX.

config ETRAX100LX_V2
	bool "ETRAX-100LX-v2"
	select ARCH_USES_GETTIMEOFFSET
	help
	  Support version 2 of the ETRAX 100LX.

config SVINTO_SIM
	bool "ETRAX-100LX-for-xsim-simulator"
	select ARCH_USES_GETTIMEOFFSET
	help
	  Support the xsim ETRAX Simulator.

config ETRAXFS
	bool "ETRAX-FS-V32"
	help
	  Support CRIS V32.

config CRIS_MACH_ARTPEC3
        bool "ARTPEC-3"
        help
          Support Axis ARTPEC-3.

endchoice

config ETRAX_VCS_SIM
	bool "VCS Simulator"
	help
	  Setup hardware to be run in the VCS simulator.

config ETRAX_ARCH_V10
       bool
       default y if ETRAX100LX || ETRAX100LX_V2
       default n if !(ETRAX100LX || ETRAX100LX_V2)

config ETRAX_ARCH_V32
       bool
       default y if (ETRAXFS || CRIS_MACH_ARTPEC3)
       default n if !(ETRAXFS || CRIS_MACH_ARTPEC3)

config ETRAX_DRAM_SIZE
	int "DRAM size (dec, in MB)"
	default "8"
	help
	  Size of DRAM (decimal in MB) typically 2, 8 or 16.

config ETRAX_VMEM_SIZE
       int "Video memory size (dec, in MB)"
       depends on ETRAX_ARCH_V32 && !ETRAXFS
       default 8 if !ETRAXFS
       help
	Size of Video accessible memory (decimal, in MB).

config ETRAX_FLASH_BUSWIDTH
	int "Buswidth of NOR flash in bytes"
	default "2"
	help
	  Width in bytes of the NOR Flash bus (1, 2 or 4). Is usually 2.

config ETRAX_NANDFLASH_BUSWIDTH
	int "Buswidth of NAND flash in bytes"
	default "1"
	help
	  Width in bytes of the NAND flash (1 or 2).

config ETRAX_FLASH1_SIZE
       int "FLASH1 size (dec, in MB. 0 = Unknown)"
       default "0"

choice
	prompt "Product debug-port"
	default ETRAX_DEBUG_PORT0

config ETRAX_DEBUG_PORT0
	bool "Serial-0"
	help
	  Choose a serial port for the ETRAX debug console.  Default to
	  port 0.

config ETRAX_DEBUG_PORT1
	bool "Serial-1"
	help
	  Use serial port 1 for the console.

config ETRAX_DEBUG_PORT2
	bool "Serial-2"
	help
	  Use serial port 2 for the console.

config ETRAX_DEBUG_PORT3
	bool "Serial-3"
	help
	  Use serial port 3 for the console.

config ETRAX_DEBUG_PORT_NULL
	bool "disabled"
	help
	  Disable serial-port debugging.

endchoice

choice
	prompt "Kernel GDB port"
	depends on ETRAX_KGDB
	default ETRAX_KGDB_PORT0
	help
	  Choose a serial port for kernel debugging.  NOTE: This port should
	  not be enabled under Drivers for built-in interfaces (as it has its
	  own initialization code) and should not be the same as the debug port.

config ETRAX_KGDB_PORT0
	bool "Serial-0"
	help
	  Use serial port 0 for kernel debugging.

config ETRAX_KGDB_PORT1
	bool "Serial-1"
	help
	  Use serial port 1 for kernel debugging.

config ETRAX_KGDB_PORT2
	bool "Serial-2"
	help
	  Use serial port 2 for kernel debugging.

config ETRAX_KGDB_PORT3
	bool "Serial-3"
	help
	  Use serial port 3 for kernel debugging.

endchoice

source arch/cris/arch-v10/Kconfig
source arch/cris/arch-v32/Kconfig

endmenu

source "net/Kconfig"

# bring in ETRAX built-in drivers
menu "Drivers for built-in interfaces"
source arch/cris/arch-v10/drivers/Kconfig
source arch/cris/arch-v32/drivers/Kconfig

config ETRAX_AXISFLASHMAP
	bool "Axis flash-map support"
	select MTD
	select MTD_CFI
	select MTD_CFI_AMDSTD
	select MTD_JEDECPROBE if ETRAX_ARCH_V32
	select MTD_CHAR
	select MTD_BLOCK
	select MTD_COMPLEX_MAPPINGS
	help
	  This option enables MTD mapping of flash devices.  Needed to use
	  flash memories.  If unsure, say Y.

config ETRAX_RTC
	bool "Real Time Clock support"
	depends on ETRAX_I2C
	help
	  Enables drivers for the Real-Time Clock battery-backed chips on
	  some products. The kernel reads the time when booting, and
	  the date can be set using ioctl(fd, RTC_SET_TIME, &rt) with rt a
	  rtc_time struct (see <file:arch/cris/include/asm/rtc.h>) on the
	  /dev/rtc device.  You can check the time with cat /proc/rtc, but
	  normal time reading should be done using libc function time and
	  friends.

choice
	prompt "RTC chip"
	depends on ETRAX_RTC
	default ETRAX_DS1302

config ETRAX_DS1302
	depends on ETRAX_ARCH_V10
	bool "DS1302"
	help
	  Enables the driver for the DS1302 Real-Time Clock battery-backed
	  chip on some products.

config ETRAX_PCF8563
	bool "PCF8563"
	help
	  Enables the driver for the PCF8563 Real-Time Clock battery-backed
	  chip on some products.

endchoice

config ETRAX_SYNCHRONOUS_SERIAL
	bool "Synchronous serial-port support"
	help
	  Select this to enable the synchronous serial port driver.

config ETRAX_SYNCHRONOUS_SERIAL_PORT0
	bool "Synchronous serial port 0 enabled"
	depends on ETRAX_SYNCHRONOUS_SERIAL
	help
	  Enabled synchronous serial port 0.

config ETRAX_SYNCHRONOUS_SERIAL0_DMA
	bool "Enable DMA on synchronous serial port 0."
	depends on ETRAX_SYNCHRONOUS_SERIAL_PORT0
	help
	  A synchronous serial port can run in manual or DMA mode.
	  Selecting this option will make it run in DMA mode.

config ETRAX_SYNCHRONOUS_SERIAL_PORT1
	bool "Synchronous serial port 1 enabled"
	depends on ETRAX_SYNCHRONOUS_SERIAL && (ETRAXFS || ETRAX_ARCH_V10)
	help
	  Enabled synchronous serial port 1.

config ETRAX_SYNCHRONOUS_SERIAL1_DMA
	bool "Enable DMA on synchronous serial port 1."
	depends on ETRAX_SYNCHRONOUS_SERIAL_PORT1
	help
	  A synchronous serial port can run in manual or DMA mode.
	  Selecting this option will make it run in DMA mode.

choice
	prompt "Network LED behavior"
	depends on ETRAX_ETHERNET
	default ETRAX_NETWORK_LED_ON_WHEN_ACTIVITY

config ETRAX_NETWORK_LED_ON_WHEN_LINK
	bool "LED_on_when_link"
	help
	  Selecting LED_on_when_link will light the LED when there is a
	  connection and will flash off when there is activity.

	  Selecting LED_on_when_activity will light the LED only when
	  there is activity.

	  This setting will also affect the behaviour of other activity LEDs
	  e.g. Bluetooth.

config ETRAX_NETWORK_LED_ON_WHEN_ACTIVITY
	bool "LED_on_when_activity"
	help
	  Selecting LED_on_when_link will light the LED when there is a
	  connection and will flash off when there is activity.

	  Selecting LED_on_when_activity will light the LED only when
	  there is activity.

	  This setting will also affect the behaviour of other activity LEDs
	  e.g. Bluetooth.

endchoice

choice
	prompt "Ser0 DMA out channel"
	depends on ETRAX_SERIAL_PORT0
	default ETRAX_SERIAL_PORT0_DMA6_OUT if ETRAX_ARCH_V32
	default ETRAX_SERIAL_PORT0_NO_DMA_OUT if ETRAX_ARCH_V10

config ETRAX_SERIAL_PORT0_NO_DMA_OUT
	bool "Ser0 uses no DMA for output"
	help
	  Do not use DMA for ser0 output.

config ETRAX_SERIAL_PORT0_DMA6_OUT
	bool "Ser0 uses DMA6 for output"
	depends on ETRAXFS
	help
	  Enables the DMA6 output channel for ser0 (ttyS0).
	  If you do not enable DMA, an interrupt for each character will be
	  used when transmitting data.
	  Normally you want to use DMA, unless you use the DMA channel for
	  something else.

config ETRAX_SERIAL_PORT0_DMA0_OUT
	bool "Ser0 uses DMA0 for output"
	depends on CRIS_MACH_ARTPEC3
	help
	  Enables the DMA0 output channel for ser0 (ttyS0).
	  If you do not enable DMA, an interrupt for each character will be
	  used when transmitting data.
	  Normally you want to use DMA, unless you use the DMA channel for
	  something else.

endchoice

choice
	prompt "Ser0 DMA in channel "
	depends on ETRAX_SERIAL_PORT0
	default ETRAX_SERIAL_PORT0_NO_DMA_IN if ETRAX_ARCH_V32
	default ETRAX_SERIAL_PORT0_DMA7_IN if ETRAX_ARCH_V10
	help
	  What DMA channel to use for ser0.

config ETRAX_SERIAL_PORT0_NO_DMA_IN
	bool "Ser0 uses no DMA for input"
	help
	  Do not use DMA for ser0 input.

config ETRAX_SERIAL_PORT0_DMA7_IN
	bool "Ser0 uses DMA7 for input"
	depends on ETRAXFS
	help
	  Enables the DMA7 input channel for ser0 (ttyS0).
	  If you do not enable DMA, an interrupt for each character will be
	  used when receiving data.
	  Normally you want to use DMA, unless you use the DMA channel for
	  something else.

config ETRAX_SERIAL_PORT0_DMA1_IN
	bool "Ser0 uses DMA1 for input"
	depends on CRIS_MACH_ARTPEC3
	help
	  Enables the DMA1 input channel for ser0 (ttyS0).
	  If you do not enable DMA, an interrupt for each character will be
	  used when receiving data.
	  Normally you want to use DMA, unless you use the DMA channel for
	  something else.

endchoice

choice
	prompt "Ser1 DMA in channel "
	depends on ETRAX_SERIAL_PORT1
	default ETRAX_SERIAL_PORT1_NO_DMA_IN if ETRAX_ARCH_V32
	default ETRAX_SERIAL_PORT1_DMA9_IN if ETRAX_ARCH_V10
	help
	  What DMA channel to use for ser1.

config ETRAX_SERIAL_PORT1_NO_DMA_IN
	bool "Ser1 uses no DMA for input"
	help
	  Do not use DMA for ser1 input.

config ETRAX_SERIAL_PORT1_DMA5_IN
	bool "Ser1 uses DMA5 for input"
	depends on ETRAX_ARCH_V32
	help
	  Enables the DMA5 input channel for ser1 (ttyS1).
	  If you do not enable DMA, an interrupt for each character will be
	  used when receiving data.
	  Normally you want this on, unless you use the DMA channel for
	  something else.

config ETRAX_SERIAL_PORT1_DMA9_IN
	depends on ETRAX_ARCH_V10
	bool "Ser1 uses DMA9 for input"

endchoice


choice
	prompt "Ser1 DMA out channel"
	depends on ETRAX_SERIAL_PORT1
	default ETRAX_SERIAL_PORT1_NO_DMA_OUT if ETRAX_ARCH_V32
	default ETRAX_SERIAL_PORT1_DMA8_OUT if ETRAX_ARCH_V10
	help
	  What DMA channel to use for ser1.

config ETRAX_SERIAL_PORT1_NO_DMA_OUT
	bool "Ser1 uses no DMA for output"
	help
	  Do not use DMA for ser1 output.

config ETRAX_SERIAL_PORT1_DMA8_OUT
	depends on ETRAX_ARCH_V10
	bool "Ser1 uses DMA8 for output"

config ETRAX_SERIAL_PORT1_DMA4_OUT
	depends on ETRAX_ARCH_V32
	bool "Ser1 uses DMA4 for output"
	help
	  Enables the DMA4 output channel for ser1 (ttyS1).
	  If you do not enable DMA, an interrupt for each character will be
	  used when transmitting data.
	  Normally you want this on, unless you use the DMA channel for
	  something else.

endchoice

choice
	prompt "Ser2 DMA out channel"
	depends on ETRAX_SERIAL_PORT2
	default ETRAX_SERIAL_PORT2_NO_DMA_OUT if ETRAX_ARCH_V32
	default ETRAX_SERIAL_PORT2_DMA2_OUT if ETRAX_ARCH_V10

config ETRAX_SERIAL_PORT2_NO_DMA_OUT
	bool "Ser2 uses no DMA for output"
	help
	  Do not use DMA for ser2 output.

config ETRAX_SERIAL_PORT2_DMA2_OUT
	bool "Ser2 uses DMA2 for output"
	depends on ETRAXFS || ETRAX_ARCH_V10
	help
	  Enables the DMA2 output channel for ser2 (ttyS2).
	  If you do not enable DMA, an interrupt for each character will be
	  used when transmitting data.
	  Normally you want to use DMA, unless you use the DMA channel for
	  something else.

config ETRAX_SERIAL_PORT2_DMA6_OUT
	bool "Ser2 uses DMA6 for output"
	depends on CRIS_MACH_ARTPEC3
	help
	  Enables the DMA6 output channel for ser2 (ttyS2).
	  If you do not enable DMA, an interrupt for each character will be
	  used when transmitting data.
	  Normally you want to use DMA, unless you use the DMA channel for
	  something else.

endchoice

choice
	prompt "Ser2 DMA in channel"
	depends on ETRAX_SERIAL_PORT2
	default ETRAX_SERIAL_PORT2_NO_DMA_IN if ETRAX_ARCH_V32
	default ETRAX_SERIAL_PORT2_DMA3_IN if ETRAX_ARCH_V10
	help
	  What DMA channel to use for ser2.

config ETRAX_SERIAL_PORT2_NO_DMA_IN
	bool "Ser2 uses no DMA for input"
	help
	  Do not use DMA for ser2 input.

config ETRAX_SERIAL_PORT2_DMA3_IN
	bool "Ser2 uses DMA3 for input"
	depends on ETRAXFS || ETRAX_ARCH_V10
	help
	  Enables the DMA3 input channel for ser2 (ttyS2).
	  If you do not enable DMA, an interrupt for each character will be
	  used when receiving data.
	  Normally you want to use DMA, unless you use the DMA channel for
	  something else.

config ETRAX_SERIAL_PORT2_DMA7_IN
	bool "Ser2 uses DMA7 for input"
	depends on CRIS_MACH_ARTPEC3
	help
	  Enables the DMA7 input channel for ser2 (ttyS2).
	  If you do not enable DMA, an interrupt for each character will be
	  used when receiving data.
	  Normally you want to use DMA, unless you use the DMA channel for
	  something else.

endchoice

choice
	prompt "Ser3 DMA in channel"
	depends on ETRAX_SERIAL_PORT3
	default ETRAX_SERIAL_PORT3_NO_DMA_IN if ETRAX_ARCH_V32
	default ETRAX_SERIAL_PORT3_DMA5_IN if ETRAX_ARCH_V10
	help
	  What DMA channel to use for ser3.

config ETRAX_SERIAL_PORT3_NO_DMA_IN
	bool "Ser3 uses no DMA for input"
	help
	  Do not use DMA for ser3 input.

config ETRAX_SERIAL_PORT3_DMA5_IN
	depends on ETRAX_ARCH_V10
	bool "DMA 5"

config ETRAX_SERIAL_PORT3_DMA9_IN
	bool "Ser3 uses DMA9 for input"
	depends on ETRAXFS
	help
	  Enables the DMA9 input channel for ser3 (ttyS3).
	  If you do not enable DMA, an interrupt for each character will be
	  used when receiving data.
	  Normally you want to use DMA, unless you use the DMA channel for
	  something else.

config ETRAX_SERIAL_PORT3_DMA3_IN
	bool "Ser3 uses DMA3 for input"
	depends on CRIS_MACH_ARTPEC3
	help
	  Enables the DMA3 input channel for ser3 (ttyS3).
	  If you do not enable DMA, an interrupt for each character will be
	  used when receiving data.
	  Normally you want to use DMA, unless you use the DMA channel for
	  something else.

endchoice

choice
	prompt "Ser3 DMA out channel"
	depends on ETRAX_SERIAL_PORT3
	default ETRAX_SERIAL_PORT3_NO_DMA_OUT if ETRAX_ARCH_V32
	default ETRAX_SERIAL_PORT3_DMA4_OUT if ETRAX_ARCH_V10

config ETRAX_SERIAL_PORT3_NO_DMA_OUT
	bool "Ser3 uses no DMA for output"
	help
	  Do not use DMA for ser3 output.

config ETRAX_SERIAL_PORT3_DMA4_OUT
	depends on ETRAX_ARCH_V10
	bool "DMA 4"

config ETRAX_SERIAL_PORT3_DMA8_OUT
	bool "Ser3 uses DMA8 for output"
	depends on ETRAXFS
	help
	  Enables the DMA8 output channel for ser3 (ttyS3).
	  If you do not enable DMA, an interrupt for each character will be
	  used when transmitting data.
	  Normally you want to use DMA, unless you use the DMA channel for
	  something else.

config ETRAX_SERIAL_PORT3_DMA2_OUT
	bool "Ser3 uses DMA2 for output"
	depends on CRIS_MACH_ARTPEC3
	help
	  Enables the DMA2 output channel for ser3 (ttyS3).
	  If you do not enable DMA, an interrupt for each character will be
	  used when transmitting data.
	  Normally you want to use DMA, unless you use the DMA channel for
	  something else.

endchoice

endmenu

source "drivers/base/Kconfig"

# standard linux drivers
source "drivers/mtd/Kconfig"

source "drivers/parport/Kconfig"

source "drivers/pnp/Kconfig"

source "drivers/block/Kconfig"

source "drivers/ide/Kconfig"

source "drivers/net/Kconfig"

source "drivers/i2c/Kconfig"

source "drivers/rtc/Kconfig"

#
# input before char - char/joystick depends on it. As does USB.
#
source "drivers/input/Kconfig"

source "drivers/char/Kconfig"

source "fs/Kconfig"

source "drivers/usb/Kconfig"

source "drivers/uwb/Kconfig"

source "drivers/staging/Kconfig"

source "arch/cris/Kconfig.debug"

source "security/Kconfig"

source "crypto/Kconfig"

source "lib/Kconfig"
Commit	Line	Data
1da177e4 LT	1	config MMU
	2	bool
	3	default y
	4
66701b14 CL	5	config ZONE_DMA
	6	bool
	7	default y
	8
1da177e4 LT	9	config RWSEM_GENERIC_SPINLOCK
	10	bool
	11	default y
	12
	13	config RWSEM_XCHGADD_ALGORITHM
	14	bool
	15
f0d1b0b3 DH	16	config ARCH_HAS_ILOG2_U32
	17	bool
	18	default n
	19
	20	config ARCH_HAS_ILOG2_U64
	21	bool
	22	default n
	23
e9f26df1 AM	24	config GENERIC_HWEIGHT
	25	bool
	26	default y
	27
1da177e4 LT	28	config GENERIC_CALIBRATE_DELAY
	29	bool
	30	default y
	31
5ea81769 AV	32	config NO_IOPORT
	33	def_bool y
	34
923dd2a4 JN	35	config FORCE_MAX_ZONEORDER
	36	int
	37	default 6
	38
1da177e4 LT	39	config CRIS
	40	bool
	41	default y
ec7748b5	42	select HAVE_IDE
4c9c6a1b	43	select GENERIC_ATOMIC64
30139785	44	select HAVE_GENERIC_HARDIRQS
15825a5c	45	select GENERIC_IRQ_SHOW
4673ca8e	46	select GENERIC_IOMAP
a4cfc31d	47	select GENERIC_SMP_IDLE_THREAD if ETRAX_ARCH_V32
5227b636	48	select GENERIC_CMOS_UPDATE
1da177e4	49
bdc80787 PA	50	config HZ
	51	int
	52	default 100
	53
1da177e4 LT	54	source "init/Kconfig"
1da177e4 LT	55
dc52ddc0 MH	56	source "kernel/Kconfig.freezer"
dc52ddc0 MH	57
1da177e4 LT	58	menu "General setup"
	59
	60	source "fs/Kconfig.binfmt"
	61
	62	config ETRAX_CMDLINE
	63	string "Kernel command line"
	64	default "root=/dev/mtdblock3"
	65	help
	66	Pass additional commands to the kernel.
	67
	68	config ETRAX_WATCHDOG
	69	bool "Enable ETRAX watchdog"
	70	help
	71	Enable the built-in watchdog timer support on ETRAX based embedded
	72	network computers.
	73
	74	config ETRAX_WATCHDOG_NICE_DOGGY
	75	bool "Disable watchdog during Oops printouts"
	76	depends on ETRAX_WATCHDOG
	77	help
	78	By enabling this you make sure that the watchdog does not bite while
	79	printing oopses. Recommended for development systems but not for
	80	production releases.
	81
	82	config ETRAX_FAST_TIMER
	83	bool "Enable ETRAX fast timer API"
	84	help
	85	This options enables the API to a fast timer implementation using
	86	timer1 to get sub jiffie resolution timers (primarily one-shot
	87	timers).
	88	This is needed if CONFIG_ETRAX_SERIAL_FAST_TIMER is enabled.
	89
923dd2a4 JN	90	config ETRAX_KMALLOCED_MODULES
923dd2a4 JN	91	bool "Enable module allocation with kmalloc"
1da177e4	92	help
923dd2a4 JN	93	Enable module allocation with kmalloc instead of vmalloc.
	94
	95	config OOM_REBOOT
	96	bool "Enable reboot at out of memory"
1da177e4	97
923dd2a4	98	source "kernel/Kconfig.preempt"
1da177e4	99
3f22ab27 DH	100	source mm/Kconfig
3f22ab27 DH	101
1da177e4 LT	102	endmenu
	103
	104	menu "Hardware setup"
	105
	106	choice
	107	prompt "Processor type"
	108	default ETRAX100LX
	109
	110	config ETRAX100LX
	111	bool "ETRAX-100LX-v1"
60dbd663	112	select ARCH_USES_GETTIMEOFFSET
1da177e4 LT	113	help
	114	Support version 1 of the ETRAX 100LX.
	115
	116	config ETRAX100LX_V2
	117	bool "ETRAX-100LX-v2"
60dbd663	118	select ARCH_USES_GETTIMEOFFSET
1da177e4 LT	119	help
	120	Support version 2 of the ETRAX 100LX.
	121
	122	config SVINTO_SIM
	123	bool "ETRAX-100LX-for-xsim-simulator"
60dbd663	124	select ARCH_USES_GETTIMEOFFSET
1da177e4 LT	125	help
	126	Support the xsim ETRAX Simulator.
	127
923dd2a4 JN	128	config ETRAXFS
	129	bool "ETRAX-FS-V32"
	130	help
	131	Support CRIS V32.
	132
	133	config CRIS_MACH_ARTPEC3
	134	bool "ARTPEC-3"
	135	help
	136	Support Axis ARTPEC-3.
	137
1da177e4 LT	138	endchoice
1da177e4 LT	139
923dd2a4 JN	140	config ETRAX_VCS_SIM
	141	bool "VCS Simulator"
	142	help
	143	Setup hardware to be run in the VCS simulator.
	144
1da177e4 LT	145	config ETRAX_ARCH_V10
	146	bool
	147	default y if ETRAX100LX \|\| ETRAX100LX_V2
	148	default n if !(ETRAX100LX \|\| ETRAX100LX_V2)
	149
923dd2a4 JN	150	config ETRAX_ARCH_V32
	151	bool
	152	default y if (ETRAXFS \|\| CRIS_MACH_ARTPEC3)
	153	default n if !(ETRAXFS \|\| CRIS_MACH_ARTPEC3)
	154
1da177e4 LT	155	config ETRAX_DRAM_SIZE
	156	int "DRAM size (dec, in MB)"
	157	default "8"
	158	help
	159	Size of DRAM (decimal in MB) typically 2, 8 or 16.
	160
923dd2a4 JN	161	config ETRAX_VMEM_SIZE
	162	int "Video memory size (dec, in MB)"
	163	depends on ETRAX_ARCH_V32 && !ETRAXFS
	164	default 8 if !ETRAXFS
	165	help
	166	Size of Video accessible memory (decimal, in MB).
	167
1da177e4	168	config ETRAX_FLASH_BUSWIDTH
923dd2a4	169	int "Buswidth of NOR flash in bytes"
1da177e4 LT	170	default "2"
1da177e4 LT	171	help
923dd2a4 JN	172	Width in bytes of the NOR Flash bus (1, 2 or 4). Is usually 2.
	173
	174	config ETRAX_NANDFLASH_BUSWIDTH
	175	int "Buswidth of NAND flash in bytes"
	176	default "1"
	177	help
	178	Width in bytes of the NAND flash (1 or 2).
	179
	180	config ETRAX_FLASH1_SIZE
	181	int "FLASH1 size (dec, in MB. 0 = Unknown)"
	182	default "0"
	183
	184	choice
	185	prompt "Product debug-port"
	186	default ETRAX_DEBUG_PORT0
	187
	188	config ETRAX_DEBUG_PORT0
	189	bool "Serial-0"
	190	help
	191	Choose a serial port for the ETRAX debug console. Default to
	192	port 0.
	193
	194	config ETRAX_DEBUG_PORT1
	195	bool "Serial-1"
	196	help
	197	Use serial port 1 for the console.
	198
	199	config ETRAX_DEBUG_PORT2
	200	bool "Serial-2"
	201	help
	202	Use serial port 2 for the console.
	203
	204	config ETRAX_DEBUG_PORT3
	205	bool "Serial-3"
	206	help
	207	Use serial port 3 for the console.
	208
	209	config ETRAX_DEBUG_PORT_NULL
	210	bool "disabled"
	211	help
	212	Disable serial-port debugging.
	213
	214	endchoice
	215
	216	choice
	217	prompt "Kernel GDB port"
	218	depends on ETRAX_KGDB
	219	default ETRAX_KGDB_PORT0
	220	help
	221	Choose a serial port for kernel debugging. NOTE: This port should
	222	not be enabled under Drivers for built-in interfaces (as it has its
	223	own initialization code) and should not be the same as the debug port.
	224
	225	config ETRAX_KGDB_PORT0
	226	bool "Serial-0"
	227	help
	228	Use serial port 0 for kernel debugging.
	229
	230	config ETRAX_KGDB_PORT1
	231	bool "Serial-1"
	232	help
	233	Use serial port 1 for kernel debugging.
	234
	235	config ETRAX_KGDB_PORT2
236	bool "Serial-2"
237	help
238	Use serial port 2 for kernel debugging.
239
240	config ETRAX_KGDB_PORT3
241	bool "Serial-3"
242	help
243	Use serial port 3 for kernel debugging.
244
245	endchoice
1da177e4 LT	246
1da177e4 LT	247	source arch/cris/arch-v10/Kconfig
2d33d563	248	source arch/cris/arch-v32/Kconfig
1da177e4 LT	249
	250	endmenu
	251
d5950b43 SR	252	source "net/Kconfig"
d5950b43 SR	253
1da177e4 LT	254	# bring in ETRAX built-in drivers
1da177e4 LT	255	menu "Drivers for built-in interfaces"
2d33d563 JN	256	source arch/cris/arch-v10/drivers/Kconfig
2d33d563 JN	257	source arch/cris/arch-v32/drivers/Kconfig
1da177e4	258
79e04fdb JN	259	config ETRAX_AXISFLASHMAP
	260	bool "Axis flash-map support"
	261	select MTD
	262	select MTD_CFI
	263	select MTD_CFI_AMDSTD
	264	select MTD_JEDECPROBE if ETRAX_ARCH_V32
	265	select MTD_CHAR
	266	select MTD_BLOCK
79e04fdb JN	267	select MTD_COMPLEX_MAPPINGS
	268	help
	269	This option enables MTD mapping of flash devices. Needed to use
	270	flash memories. If unsure, say Y.
	271
c3d6dddd JN	272	config ETRAX_RTC
	273	bool "Real Time Clock support"
	274	depends on ETRAX_I2C
	275	help
	276	Enables drivers for the Real-Time Clock battery-backed chips on
	277	some products. The kernel reads the time when booting, and
	278	the date can be set using ioctl(fd, RTC_SET_TIME, &rt) with rt a
0348299a JFS	279	rtc_time struct (see <file:arch/cris/include/asm/rtc.h>) on the
0348299a JFS	280	/dev/rtc device. You can check the time with cat /proc/rtc, but
c3d6dddd JN	281	normal time reading should be done using libc function time and
	282	friends.
	283
923dd2a4 JN	284	choice
	285	prompt "RTC chip"
	286	depends on ETRAX_RTC
7673538c	287	default ETRAX_DS1302
923dd2a4 JN	288
	289	config ETRAX_DS1302
	290	depends on ETRAX_ARCH_V10
	291	bool "DS1302"
	292	help
	293	Enables the driver for the DS1302 Real-Time Clock battery-backed
	294	chip on some products.
	295
	296	config ETRAX_PCF8563
	297	bool "PCF8563"
	298	help
	299	Enables the driver for the PCF8563 Real-Time Clock battery-backed
	300	chip on some products.
	301
	302	endchoice
	303
c974a9e5 JN	304	config ETRAX_SYNCHRONOUS_SERIAL
	305	bool "Synchronous serial-port support"
	306	help
	307	Select this to enable the synchronous serial port driver.
	308
	309	config ETRAX_SYNCHRONOUS_SERIAL_PORT0
	310	bool "Synchronous serial port 0 enabled"
	311	depends on ETRAX_SYNCHRONOUS_SERIAL
	312	help
	313	Enabled synchronous serial port 0.
	314
	315	config ETRAX_SYNCHRONOUS_SERIAL0_DMA
	316	bool "Enable DMA on synchronous serial port 0."
	317	depends on ETRAX_SYNCHRONOUS_SERIAL_PORT0
	318	help
	319	A synchronous serial port can run in manual or DMA mode.
	320	Selecting this option will make it run in DMA mode.
	321
	322	config ETRAX_SYNCHRONOUS_SERIAL_PORT1
	323	bool "Synchronous serial port 1 enabled"
	324	depends on ETRAX_SYNCHRONOUS_SERIAL && (ETRAXFS \|\| ETRAX_ARCH_V10)
	325	help
	326	Enabled synchronous serial port 1.
	327
	328	config ETRAX_SYNCHRONOUS_SERIAL1_DMA
	329	bool "Enable DMA on synchronous serial port 1."
	330	depends on ETRAX_SYNCHRONOUS_SERIAL_PORT1
	331	help
	332	A synchronous serial port can run in manual or DMA mode.
	333	Selecting this option will make it run in DMA mode.
	334
923dd2a4 JN	335	choice
	336	prompt "Network LED behavior"
	337	depends on ETRAX_ETHERNET
	338	default ETRAX_NETWORK_LED_ON_WHEN_ACTIVITY
	339
	340	config ETRAX_NETWORK_LED_ON_WHEN_LINK
	341	bool "LED_on_when_link"
	342	help
	343	Selecting LED_on_when_link will light the LED when there is a
	344	connection and will flash off when there is activity.
	345
	346	Selecting LED_on_when_activity will light the LED only when
	347	there is activity.
	348
	349	This setting will also affect the behaviour of other activity LEDs
	350	e.g. Bluetooth.
	351
	352	config ETRAX_NETWORK_LED_ON_WHEN_ACTIVITY
	353	bool "LED_on_when_activity"
	354	help
	355	Selecting LED_on_when_link will light the LED when there is a
	356	connection and will flash off when there is activity.
	357
	358	Selecting LED_on_when_activity will light the LED only when
	359	there is activity.
	360
	361	This setting will also affect the behaviour of other activity LEDs
	362	e.g. Bluetooth.
	363
	364	endchoice
	365
	366	choice
	367	prompt "Ser0 DMA out channel"
	368	depends on ETRAX_SERIAL_PORT0
	369	default ETRAX_SERIAL_PORT0_DMA6_OUT if ETRAX_ARCH_V32
	370	default ETRAX_SERIAL_PORT0_NO_DMA_OUT if ETRAX_ARCH_V10
	371
	372	config ETRAX_SERIAL_PORT0_NO_DMA_OUT
	373	bool "Ser0 uses no DMA for output"
	374	help
	375	Do not use DMA for ser0 output.
	376
	377	config ETRAX_SERIAL_PORT0_DMA6_OUT
	378	bool "Ser0 uses DMA6 for output"
	379	depends on ETRAXFS
	380	help
	381	Enables the DMA6 output channel for ser0 (ttyS0).
	382	If you do not enable DMA, an interrupt for each character will be
	383	used when transmitting data.
	384	Normally you want to use DMA, unless you use the DMA channel for
	385	something else.
	386
	387	config ETRAX_SERIAL_PORT0_DMA0_OUT
	388	bool "Ser0 uses DMA0 for output"
	389	depends on CRIS_MACH_ARTPEC3
	390	help
	391	Enables the DMA0 output channel for ser0 (ttyS0).
	392	If you do not enable DMA, an interrupt for each character will be
	393	used when transmitting data.
	394	Normally you want to use DMA, unless you use the DMA channel for
	395	something else.
	396
	397	endchoice
	398
399	choice
400	prompt "Ser0 DMA in channel "
401	depends on ETRAX_SERIAL_PORT0
402	default ETRAX_SERIAL_PORT0_NO_DMA_IN if ETRAX_ARCH_V32
403	default ETRAX_SERIAL_PORT0_DMA7_IN if ETRAX_ARCH_V10
404	help
405	What DMA channel to use for ser0.
406
407	config ETRAX_SERIAL_PORT0_NO_DMA_IN
408	bool "Ser0 uses no DMA for input"
409	help
410	Do not use DMA for ser0 input.
411
412	config ETRAX_SERIAL_PORT0_DMA7_IN
413	bool "Ser0 uses DMA7 for input"
414	depends on ETRAXFS
415	help
416	Enables the DMA7 input channel for ser0 (ttyS0).
417	If you do not enable DMA, an interrupt for each character will be
418	used when receiving data.
419	Normally you want to use DMA, unless you use the DMA channel for
420	something else.
421
422	config ETRAX_SERIAL_PORT0_DMA1_IN
423	bool "Ser0 uses DMA1 for input"
424	depends on CRIS_MACH_ARTPEC3
425	help
426	Enables the DMA1 input channel for ser0 (ttyS0).
427	If you do not enable DMA, an interrupt for each character will be
692105b8	428	used when receiving data.
923dd2a4 JN	429	Normally you want to use DMA, unless you use the DMA channel for
	430	something else.
	431
	432	endchoice
	433
	434	choice
	435	prompt "Ser1 DMA in channel "
	436	depends on ETRAX_SERIAL_PORT1
	437	default ETRAX_SERIAL_PORT1_NO_DMA_IN if ETRAX_ARCH_V32
	438	default ETRAX_SERIAL_PORT1_DMA9_IN if ETRAX_ARCH_V10
	439	help
	440	What DMA channel to use for ser1.
	441
	442	config ETRAX_SERIAL_PORT1_NO_DMA_IN
	443	bool "Ser1 uses no DMA for input"
	444	help
	445	Do not use DMA for ser1 input.
	446
	447	config ETRAX_SERIAL_PORT1_DMA5_IN
	448	bool "Ser1 uses DMA5 for input"
	449	depends on ETRAX_ARCH_V32
	450	help
	451	Enables the DMA5 input channel for ser1 (ttyS1).
	452	If you do not enable DMA, an interrupt for each character will be
	453	used when receiving data.
	454	Normally you want this on, unless you use the DMA channel for
	455	something else.
	456
	457	config ETRAX_SERIAL_PORT1_DMA9_IN
	458	depends on ETRAX_ARCH_V10
	459	bool "Ser1 uses DMA9 for input"
	460
	461	endchoice
	462
	463
	464	choice
	465	prompt "Ser1 DMA out channel"
	466	depends on ETRAX_SERIAL_PORT1
	467	default ETRAX_SERIAL_PORT1_NO_DMA_OUT if ETRAX_ARCH_V32
	468	default ETRAX_SERIAL_PORT1_DMA8_OUT if ETRAX_ARCH_V10
	469	help
	470	What DMA channel to use for ser1.
	471
	472	config ETRAX_SERIAL_PORT1_NO_DMA_OUT
	473	bool "Ser1 uses no DMA for output"
	474	help
	475	Do not use DMA for ser1 output.
	476
	477	config ETRAX_SERIAL_PORT1_DMA8_OUT
	478	depends on ETRAX_ARCH_V10
	479	bool "Ser1 uses DMA8 for output"
	480
	481	config ETRAX_SERIAL_PORT1_DMA4_OUT
	482	depends on ETRAX_ARCH_V32
	483	bool "Ser1 uses DMA4 for output"
	484	help
	485	Enables the DMA4 output channel for ser1 (ttyS1).
	486	If you do not enable DMA, an interrupt for each character will be
	487	used when transmitting data.
	488	Normally you want this on, unless you use the DMA channel for
	489	something else.
	490
	491	endchoice
	492
493	choice
494	prompt "Ser2 DMA out channel"
495	depends on ETRAX_SERIAL_PORT2
496	default ETRAX_SERIAL_PORT2_NO_DMA_OUT if ETRAX_ARCH_V32
497	default ETRAX_SERIAL_PORT2_DMA2_OUT if ETRAX_ARCH_V10
498
499	config ETRAX_SERIAL_PORT2_NO_DMA_OUT
500	bool "Ser2 uses no DMA for output"
501	help
502	Do not use DMA for ser2 output.
503
504	config ETRAX_SERIAL_PORT2_DMA2_OUT
505	bool "Ser2 uses DMA2 for output"
506	depends on ETRAXFS \|\| ETRAX_ARCH_V10
507	help
508	Enables the DMA2 output channel for ser2 (ttyS2).
509	If you do not enable DMA, an interrupt for each character will be
510	used when transmitting data.
511	Normally you want to use DMA, unless you use the DMA channel for
512	something else.
513
514	config ETRAX_SERIAL_PORT2_DMA6_OUT
515	bool "Ser2 uses DMA6 for output"
516	depends on CRIS_MACH_ARTPEC3
517	help
518	Enables the DMA6 output channel for ser2 (ttyS2).
519	If you do not enable DMA, an interrupt for each character will be
520	used when transmitting data.
521	Normally you want to use DMA, unless you use the DMA channel for
522	something else.
523
524	endchoice
525
526	choice
527	prompt "Ser2 DMA in channel"
528	depends on ETRAX_SERIAL_PORT2
529	default ETRAX_SERIAL_PORT2_NO_DMA_IN if ETRAX_ARCH_V32
530	default ETRAX_SERIAL_PORT2_DMA3_IN if ETRAX_ARCH_V10
531	help
532	What DMA channel to use for ser2.
533
534	config ETRAX_SERIAL_PORT2_NO_DMA_IN
535	bool "Ser2 uses no DMA for input"
536	help
537	Do not use DMA for ser2 input.
538
539	config ETRAX_SERIAL_PORT2_DMA3_IN
540	bool "Ser2 uses DMA3 for input"
541	depends on ETRAXFS \|\| ETRAX_ARCH_V10
542	help
543	Enables the DMA3 input channel for ser2 (ttyS2).
544	If you do not enable DMA, an interrupt for each character will be
545	used when receiving data.
546	Normally you want to use DMA, unless you use the DMA channel for
547	something else.
548
549	config ETRAX_SERIAL_PORT2_DMA7_IN
550	bool "Ser2 uses DMA7 for input"
551	depends on CRIS_MACH_ARTPEC3
552	help
553	Enables the DMA7 input channel for ser2 (ttyS2).
554	If you do not enable DMA, an interrupt for each character will be
692105b8	555	used when receiving data.
923dd2a4 JN	556	Normally you want to use DMA, unless you use the DMA channel for
	557	something else.
	558
	559	endchoice
	560
	561	choice
	562	prompt "Ser3 DMA in channel"
	563	depends on ETRAX_SERIAL_PORT3
	564	default ETRAX_SERIAL_PORT3_NO_DMA_IN if ETRAX_ARCH_V32
	565	default ETRAX_SERIAL_PORT3_DMA5_IN if ETRAX_ARCH_V10
	566	help
	567	What DMA channel to use for ser3.
	568
	569	config ETRAX_SERIAL_PORT3_NO_DMA_IN
	570	bool "Ser3 uses no DMA for input"
	571	help
	572	Do not use DMA for ser3 input.
	573
	574	config ETRAX_SERIAL_PORT3_DMA5_IN
	575	depends on ETRAX_ARCH_V10
	576	bool "DMA 5"
	577
	578	config ETRAX_SERIAL_PORT3_DMA9_IN
	579	bool "Ser3 uses DMA9 for input"
	580	depends on ETRAXFS
	581	help
	582	Enables the DMA9 input channel for ser3 (ttyS3).
	583	If you do not enable DMA, an interrupt for each character will be
	584	used when receiving data.
	585	Normally you want to use DMA, unless you use the DMA channel for
	586	something else.
	587
	588	config ETRAX_SERIAL_PORT3_DMA3_IN
	589	bool "Ser3 uses DMA3 for input"
	590	depends on CRIS_MACH_ARTPEC3
	591	help
	592	Enables the DMA3 input channel for ser3 (ttyS3).
	593	If you do not enable DMA, an interrupt for each character will be
692105b8	594	used when receiving data.
923dd2a4 JN	595	Normally you want to use DMA, unless you use the DMA channel for
	596	something else.
	597
	598	endchoice
	599
	600	choice
	601	prompt "Ser3 DMA out channel"
	602	depends on ETRAX_SERIAL_PORT3
	603	default ETRAX_SERIAL_PORT3_NO_DMA_OUT if ETRAX_ARCH_V32
	604	default ETRAX_SERIAL_PORT3_DMA4_OUT if ETRAX_ARCH_V10
	605
	606	config ETRAX_SERIAL_PORT3_NO_DMA_OUT
	607	bool "Ser3 uses no DMA for output"
	608	help
	609	Do not use DMA for ser3 output.
	610
	611	config ETRAX_SERIAL_PORT3_DMA4_OUT
	612	depends on ETRAX_ARCH_V10
	613	bool "DMA 4"
	614
	615	config ETRAX_SERIAL_PORT3_DMA8_OUT
	616	bool "Ser3 uses DMA8 for output"
	617	depends on ETRAXFS
	618	help
	619	Enables the DMA8 output channel for ser3 (ttyS3).
	620	If you do not enable DMA, an interrupt for each character will be
	621	used when transmitting data.
	622	Normally you want to use DMA, unless you use the DMA channel for
	623	something else.
	624
	625	config ETRAX_SERIAL_PORT3_DMA2_OUT
	626	bool "Ser3 uses DMA2 for output"
	627	depends on CRIS_MACH_ARTPEC3
	628	help
	629	Enables the DMA2 output channel for ser3 (ttyS3).
	630	If you do not enable DMA, an interrupt for each character will be
	631	used when transmitting data.
	632	Normally you want to use DMA, unless you use the DMA channel for
	633	something else.
	634
	635	endchoice
	636
1da177e4 LT	637	endmenu
	638
	639	source "drivers/base/Kconfig"
	640
	641	# standard linux drivers
	642	source "drivers/mtd/Kconfig"
	643
	644	source "drivers/parport/Kconfig"
	645
	646	source "drivers/pnp/Kconfig"
	647
	648	source "drivers/block/Kconfig"
	649
1da177e4 LT	650	source "drivers/ide/Kconfig"
1da177e4 LT	651
d5950b43	652	source "drivers/net/Kconfig"
1da177e4	653
7b275523 JN	654	source "drivers/i2c/Kconfig"
	655
	656	source "drivers/rtc/Kconfig"
	657
1da177e4 LT	658	#
	659	# input before char - char/joystick depends on it. As does USB.
	660	#
	661	source "drivers/input/Kconfig"
	662
	663	source "drivers/char/Kconfig"
	664
1da177e4 LT	665	source "fs/Kconfig"
1da177e4 LT	666
1da177e4 LT	667	source "drivers/usb/Kconfig"
1da177e4 LT	668
2f86c3e6 GKH	669	source "drivers/uwb/Kconfig"
2f86c3e6 GKH	670
6e38a2ba DH	671	source "drivers/staging/Kconfig"
6e38a2ba DH	672
1da177e4 LT	673	source "arch/cris/Kconfig.debug"
	674
	675	source "security/Kconfig"
	676
	677	source "crypto/Kconfig"
	678
	679	source "lib/Kconfig"