Commit | Line | Data |
---|---|---|
669a5db4 JG |
1 | /* |
2 | * pata_optidma.c - Opti DMA PATA for new ATA layer | |
3 | * (C) 2006 Red Hat Inc | |
4 | * Alan Cox <alan@redhat.com> | |
5 | * | |
6 | * The Opti DMA controllers are related to the older PIO PCI controllers | |
7 | * and indeed the VLB ones. The main differences are that the timing | |
8 | * numbers are now based off PCI clocks not VLB and differ, and that | |
9 | * MWDMA is supported. | |
10 | * | |
11 | * This driver should support Viper-N+, FireStar, FireStar Plus. | |
12 | * | |
13 | * These devices support virtual DMA for read (aka the CS5520). Later | |
14 | * chips support UDMA33, but only if the rest of the board logic does, | |
15 | * so you have to get this right. We don't support the virtual DMA | |
16 | * but we do handle UDMA. | |
17 | * | |
18 | * Bits that are worth knowing | |
19 | * Most control registers are shadowed into I/O registers | |
20 | * 0x1F5 bit 0 tells you if the PCI/VLB clock is 33 or 25Mhz | |
21 | * Virtual DMA registers *move* between rev 0x02 and rev 0x10 | |
22 | * UDMA requires a 66MHz FSB | |
23 | * | |
24 | */ | |
25 | ||
26 | #include <linux/kernel.h> | |
27 | #include <linux/module.h> | |
28 | #include <linux/pci.h> | |
29 | #include <linux/init.h> | |
30 | #include <linux/blkdev.h> | |
31 | #include <linux/delay.h> | |
32 | #include <scsi/scsi_host.h> | |
33 | #include <linux/libata.h> | |
34 | ||
35 | #define DRV_NAME "pata_optidma" | |
5c25bf0d | 36 | #define DRV_VERSION "0.3.2" |
669a5db4 JG |
37 | |
38 | enum { | |
39 | READ_REG = 0, /* index of Read cycle timing register */ | |
40 | WRITE_REG = 1, /* index of Write cycle timing register */ | |
41 | CNTRL_REG = 3, /* index of Control register */ | |
42 | STRAP_REG = 5, /* index of Strap register */ | |
43 | MISC_REG = 6 /* index of Miscellaneous register */ | |
44 | }; | |
45 | ||
46 | static int pci_clock; /* 0 = 33 1 = 25 */ | |
47 | ||
48 | /** | |
49 | * optidma_pre_reset - probe begin | |
cc0680a5 | 50 | * @link: ATA link |
d4b2bab4 | 51 | * @deadline: deadline jiffies for the operation |
669a5db4 JG |
52 | * |
53 | * Set up cable type and use generic probe init | |
54 | */ | |
85cd7251 | 55 | |
cc0680a5 | 56 | static int optidma_pre_reset(struct ata_link *link, unsigned long deadline) |
669a5db4 | 57 | { |
cc0680a5 | 58 | struct ata_port *ap = link->ap; |
669a5db4 | 59 | struct pci_dev *pdev = to_pci_dev(ap->host->dev); |
85cd7251 | 60 | static const struct pci_bits optidma_enable_bits = { |
669a5db4 JG |
61 | 0x40, 1, 0x08, 0x00 |
62 | }; | |
63 | ||
c961922b AC |
64 | if (ap->port_no && !pci_test_config_bits(pdev, &optidma_enable_bits)) |
65 | return -ENOENT; | |
66 | ||
cc0680a5 | 67 | return ata_std_prereset(link, deadline); |
669a5db4 JG |
68 | } |
69 | ||
70 | /** | |
71 | * optidma_probe_reset - probe reset | |
72 | * @ap: ATA port | |
73 | * | |
74 | * Perform the ATA probe and bus reset sequence plus specific handling | |
75 | * for this hardware. The Opti needs little handling - we have no UDMA66 | |
76 | * capability that needs cable detection. All we must do is check the port | |
77 | * is enabled. | |
78 | */ | |
79 | ||
80 | static void optidma_error_handler(struct ata_port *ap) | |
81 | { | |
82 | ata_bmdma_drive_eh(ap, optidma_pre_reset, ata_std_softreset, NULL, ata_std_postreset); | |
83 | } | |
84 | ||
85 | /** | |
86 | * optidma_unlock - unlock control registers | |
87 | * @ap: ATA port | |
88 | * | |
89 | * Unlock the control register block for this adapter. Registers must not | |
90 | * be unlocked in a situation where libata might look at them. | |
91 | */ | |
85cd7251 | 92 | |
669a5db4 JG |
93 | static void optidma_unlock(struct ata_port *ap) |
94 | { | |
0d5ff566 | 95 | void __iomem *regio = ap->ioaddr.cmd_addr; |
85cd7251 | 96 | |
669a5db4 | 97 | /* These 3 unlock the control register access */ |
0d5ff566 TH |
98 | ioread16(regio + 1); |
99 | ioread16(regio + 1); | |
100 | iowrite8(3, regio + 2); | |
669a5db4 JG |
101 | } |
102 | ||
103 | /** | |
104 | * optidma_lock - issue temporary relock | |
105 | * @ap: ATA port | |
106 | * | |
107 | * Re-lock the configuration register settings. | |
108 | */ | |
85cd7251 | 109 | |
669a5db4 JG |
110 | static void optidma_lock(struct ata_port *ap) |
111 | { | |
0d5ff566 | 112 | void __iomem *regio = ap->ioaddr.cmd_addr; |
85cd7251 | 113 | |
669a5db4 | 114 | /* Relock */ |
0d5ff566 | 115 | iowrite8(0x83, regio + 2); |
669a5db4 JG |
116 | } |
117 | ||
118 | /** | |
5c25bf0d | 119 | * optidma_mode_setup - set mode data |
669a5db4 JG |
120 | * @ap: ATA interface |
121 | * @adev: ATA device | |
122 | * @mode: Mode to set | |
123 | * | |
124 | * Called to do the DMA or PIO mode setup. Timing numbers are all | |
125 | * pre computed to keep the code clean. There are two tables depending | |
126 | * on the hardware clock speed. | |
127 | * | |
128 | * WARNING: While we do this the IDE registers vanish. If we take an | |
129 | * IRQ here we depend on the host set locking to avoid catastrophe. | |
130 | */ | |
131 | ||
5c25bf0d | 132 | static void optidma_mode_setup(struct ata_port *ap, struct ata_device *adev, u8 mode) |
669a5db4 JG |
133 | { |
134 | struct ata_device *pair = ata_dev_pair(adev); | |
135 | int pio = adev->pio_mode - XFER_PIO_0; | |
136 | int dma = adev->dma_mode - XFER_MW_DMA_0; | |
0d5ff566 | 137 | void __iomem *regio = ap->ioaddr.cmd_addr; |
669a5db4 JG |
138 | u8 addr; |
139 | ||
140 | /* Address table precomputed with a DCLK of 2 */ | |
141 | static const u8 addr_timing[2][5] = { | |
142 | { 0x30, 0x20, 0x20, 0x10, 0x10 }, | |
143 | { 0x20, 0x20, 0x10, 0x10, 0x10 } | |
144 | }; | |
145 | static const u8 data_rec_timing[2][5] = { | |
146 | { 0x59, 0x46, 0x30, 0x20, 0x20 }, | |
147 | { 0x46, 0x32, 0x20, 0x20, 0x10 } | |
148 | }; | |
149 | static const u8 dma_data_rec_timing[2][3] = { | |
150 | { 0x76, 0x20, 0x20 }, | |
151 | { 0x54, 0x20, 0x10 } | |
152 | }; | |
153 | ||
154 | /* Switch from IDE to control mode */ | |
155 | optidma_unlock(ap); | |
85cd7251 | 156 | |
669a5db4 JG |
157 | |
158 | /* | |
159 | * As with many controllers the address setup time is shared | |
160 | * and must suit both devices if present. FIXME: Check if we | |
161 | * need to look at slowest of PIO/DMA mode of either device | |
162 | */ | |
163 | ||
164 | if (mode >= XFER_MW_DMA_0) | |
165 | addr = 0; | |
166 | else | |
167 | addr = addr_timing[pci_clock][pio]; | |
85cd7251 | 168 | |
669a5db4 JG |
169 | if (pair) { |
170 | u8 pair_addr; | |
171 | /* Hardware constraint */ | |
172 | if (pair->dma_mode) | |
173 | pair_addr = 0; | |
174 | else | |
175 | pair_addr = addr_timing[pci_clock][pair->pio_mode - XFER_PIO_0]; | |
176 | if (pair_addr > addr) | |
177 | addr = pair_addr; | |
178 | } | |
85cd7251 | 179 | |
669a5db4 JG |
180 | /* Commence primary programming sequence */ |
181 | /* First we load the device number into the timing select */ | |
0d5ff566 | 182 | iowrite8(adev->devno, regio + MISC_REG); |
669a5db4 JG |
183 | /* Now we load the data timings into read data/write data */ |
184 | if (mode < XFER_MW_DMA_0) { | |
0d5ff566 TH |
185 | iowrite8(data_rec_timing[pci_clock][pio], regio + READ_REG); |
186 | iowrite8(data_rec_timing[pci_clock][pio], regio + WRITE_REG); | |
669a5db4 | 187 | } else if (mode < XFER_UDMA_0) { |
0d5ff566 TH |
188 | iowrite8(dma_data_rec_timing[pci_clock][dma], regio + READ_REG); |
189 | iowrite8(dma_data_rec_timing[pci_clock][dma], regio + WRITE_REG); | |
669a5db4 JG |
190 | } |
191 | /* Finally we load the address setup into the misc register */ | |
0d5ff566 | 192 | iowrite8(addr | adev->devno, regio + MISC_REG); |
669a5db4 JG |
193 | |
194 | /* Programming sequence complete, timing 0 dev 0, timing 1 dev 1 */ | |
0d5ff566 | 195 | iowrite8(0x85, regio + CNTRL_REG); |
85cd7251 | 196 | |
669a5db4 JG |
197 | /* Switch back to IDE mode */ |
198 | optidma_lock(ap); | |
85cd7251 | 199 | |
669a5db4 JG |
200 | /* Note: at this point our programming is incomplete. We are |
201 | not supposed to program PCI 0x43 "things we hacked onto the chip" | |
202 | until we've done both sets of PIO/DMA timings */ | |
203 | } | |
204 | ||
205 | /** | |
5c25bf0d | 206 | * optiplus_mode_setup - DMA setup for Firestar Plus |
669a5db4 JG |
207 | * @ap: ATA port |
208 | * @adev: device | |
209 | * @mode: desired mode | |
210 | * | |
211 | * The Firestar plus has additional UDMA functionality for UDMA0-2 and | |
212 | * requires we do some additional work. Because the base work we must do | |
213 | * is mostly shared we wrap the Firestar setup functionality in this | |
214 | * one | |
215 | */ | |
216 | ||
5c25bf0d | 217 | static void optiplus_mode_setup(struct ata_port *ap, struct ata_device *adev, u8 mode) |
669a5db4 JG |
218 | { |
219 | struct pci_dev *pdev = to_pci_dev(ap->host->dev); | |
220 | u8 udcfg; | |
221 | u8 udslave; | |
222 | int dev2 = 2 * adev->devno; | |
223 | int unit = 2 * ap->port_no + adev->devno; | |
224 | int udma = mode - XFER_UDMA_0; | |
85cd7251 | 225 | |
669a5db4 JG |
226 | pci_read_config_byte(pdev, 0x44, &udcfg); |
227 | if (mode <= XFER_UDMA_0) { | |
228 | udcfg &= ~(1 << unit); | |
5c25bf0d | 229 | optidma_mode_setup(ap, adev, adev->dma_mode); |
669a5db4 JG |
230 | } else { |
231 | udcfg |= (1 << unit); | |
232 | if (ap->port_no) { | |
233 | pci_read_config_byte(pdev, 0x45, &udslave); | |
234 | udslave &= ~(0x03 << dev2); | |
235 | udslave |= (udma << dev2); | |
236 | pci_write_config_byte(pdev, 0x45, udslave); | |
237 | } else { | |
238 | udcfg &= ~(0x30 << dev2); | |
239 | udcfg |= (udma << dev2); | |
240 | } | |
241 | } | |
242 | pci_write_config_byte(pdev, 0x44, udcfg); | |
243 | } | |
244 | ||
245 | /** | |
246 | * optidma_set_pio_mode - PIO setup callback | |
247 | * @ap: ATA port | |
248 | * @adev: Device | |
249 | * | |
250 | * The libata core provides separate functions for handling PIO and | |
251 | * DMA programming. The architecture of the Firestar makes it easier | |
252 | * for us to have a common function so we provide wrappers | |
253 | */ | |
85cd7251 | 254 | |
669a5db4 JG |
255 | static void optidma_set_pio_mode(struct ata_port *ap, struct ata_device *adev) |
256 | { | |
5c25bf0d | 257 | optidma_mode_setup(ap, adev, adev->pio_mode); |
669a5db4 JG |
258 | } |
259 | ||
260 | /** | |
261 | * optidma_set_dma_mode - DMA setup callback | |
262 | * @ap: ATA port | |
263 | * @adev: Device | |
264 | * | |
265 | * The libata core provides separate functions for handling PIO and | |
266 | * DMA programming. The architecture of the Firestar makes it easier | |
267 | * for us to have a common function so we provide wrappers | |
268 | */ | |
85cd7251 | 269 | |
669a5db4 JG |
270 | static void optidma_set_dma_mode(struct ata_port *ap, struct ata_device *adev) |
271 | { | |
5c25bf0d | 272 | optidma_mode_setup(ap, adev, adev->dma_mode); |
669a5db4 JG |
273 | } |
274 | ||
275 | /** | |
276 | * optiplus_set_pio_mode - PIO setup callback | |
277 | * @ap: ATA port | |
278 | * @adev: Device | |
279 | * | |
280 | * The libata core provides separate functions for handling PIO and | |
281 | * DMA programming. The architecture of the Firestar makes it easier | |
282 | * for us to have a common function so we provide wrappers | |
283 | */ | |
85cd7251 | 284 | |
669a5db4 JG |
285 | static void optiplus_set_pio_mode(struct ata_port *ap, struct ata_device *adev) |
286 | { | |
5c25bf0d | 287 | optiplus_mode_setup(ap, adev, adev->pio_mode); |
669a5db4 JG |
288 | } |
289 | ||
290 | /** | |
291 | * optiplus_set_dma_mode - DMA setup callback | |
292 | * @ap: ATA port | |
293 | * @adev: Device | |
294 | * | |
295 | * The libata core provides separate functions for handling PIO and | |
296 | * DMA programming. The architecture of the Firestar makes it easier | |
297 | * for us to have a common function so we provide wrappers | |
298 | */ | |
85cd7251 | 299 | |
669a5db4 JG |
300 | static void optiplus_set_dma_mode(struct ata_port *ap, struct ata_device *adev) |
301 | { | |
5c25bf0d | 302 | optiplus_mode_setup(ap, adev, adev->dma_mode); |
669a5db4 JG |
303 | } |
304 | ||
305 | /** | |
306 | * optidma_make_bits - PCI setup helper | |
307 | * @adev: ATA device | |
308 | * | |
309 | * Turn the ATA device setup into PCI configuration bits | |
310 | * for register 0x43 and return the two bits needed. | |
311 | */ | |
85cd7251 | 312 | |
669a5db4 JG |
313 | static u8 optidma_make_bits43(struct ata_device *adev) |
314 | { | |
315 | static const u8 bits43[5] = { | |
316 | 0, 0, 0, 1, 2 | |
317 | }; | |
318 | if (!ata_dev_enabled(adev)) | |
319 | return 0; | |
320 | if (adev->dma_mode) | |
321 | return adev->dma_mode - XFER_MW_DMA_0; | |
322 | return bits43[adev->pio_mode - XFER_PIO_0]; | |
323 | } | |
324 | ||
325 | /** | |
5c25bf0d | 326 | * optidma_set_mode - mode setup |
0260731f | 327 | * @link: link to set up |
669a5db4 | 328 | * |
5c25bf0d AC |
329 | * Use the standard setup to tune the chipset and then finalise the |
330 | * configuration by writing the nibble of extra bits of data into | |
331 | * the chip. | |
669a5db4 | 332 | */ |
85cd7251 | 333 | |
0260731f | 334 | static int optidma_set_mode(struct ata_link *link, struct ata_device **r_failed) |
669a5db4 | 335 | { |
0260731f | 336 | struct ata_port *ap = link->ap; |
669a5db4 JG |
337 | u8 r; |
338 | int nybble = 4 * ap->port_no; | |
339 | struct pci_dev *pdev = to_pci_dev(ap->host->dev); | |
0260731f | 340 | int rc = ata_do_set_mode(link, r_failed); |
5c25bf0d AC |
341 | if (rc == 0) { |
342 | pci_read_config_byte(pdev, 0x43, &r); | |
343 | ||
344 | r &= (0x0F << nybble); | |
0260731f TH |
345 | r |= (optidma_make_bits43(&link->device[0]) + |
346 | (optidma_make_bits43(&link->device[0]) << 2)) << nybble; | |
5c25bf0d AC |
347 | pci_write_config_byte(pdev, 0x43, r); |
348 | } | |
349 | return rc; | |
669a5db4 JG |
350 | } |
351 | ||
352 | static struct scsi_host_template optidma_sht = { | |
353 | .module = THIS_MODULE, | |
354 | .name = DRV_NAME, | |
355 | .ioctl = ata_scsi_ioctl, | |
356 | .queuecommand = ata_scsi_queuecmd, | |
357 | .can_queue = ATA_DEF_QUEUE, | |
358 | .this_id = ATA_SHT_THIS_ID, | |
359 | .sg_tablesize = LIBATA_MAX_PRD, | |
669a5db4 JG |
360 | .cmd_per_lun = ATA_SHT_CMD_PER_LUN, |
361 | .emulated = ATA_SHT_EMULATED, | |
362 | .use_clustering = ATA_SHT_USE_CLUSTERING, | |
363 | .proc_name = DRV_NAME, | |
364 | .dma_boundary = ATA_DMA_BOUNDARY, | |
365 | .slave_configure = ata_scsi_slave_config, | |
afdfe899 | 366 | .slave_destroy = ata_scsi_slave_destroy, |
669a5db4 JG |
367 | .bios_param = ata_std_bios_param, |
368 | }; | |
369 | ||
370 | static struct ata_port_operations optidma_port_ops = { | |
669a5db4 JG |
371 | .set_piomode = optidma_set_pio_mode, |
372 | .set_dmamode = optidma_set_dma_mode, | |
373 | ||
374 | .tf_load = ata_tf_load, | |
375 | .tf_read = ata_tf_read, | |
376 | .check_status = ata_check_status, | |
377 | .exec_command = ata_exec_command, | |
378 | .dev_select = ata_std_dev_select, | |
379 | ||
380 | .freeze = ata_bmdma_freeze, | |
381 | .thaw = ata_bmdma_thaw, | |
382 | .post_internal_cmd = ata_bmdma_post_internal_cmd, | |
383 | .error_handler = optidma_error_handler, | |
5c25bf0d AC |
384 | .set_mode = optidma_set_mode, |
385 | .cable_detect = ata_cable_40wire, | |
669a5db4 JG |
386 | |
387 | .bmdma_setup = ata_bmdma_setup, | |
388 | .bmdma_start = ata_bmdma_start, | |
389 | .bmdma_stop = ata_bmdma_stop, | |
390 | .bmdma_status = ata_bmdma_status, | |
391 | ||
392 | .qc_prep = ata_qc_prep, | |
393 | .qc_issue = ata_qc_issue_prot, | |
bda30288 | 394 | |
0d5ff566 | 395 | .data_xfer = ata_data_xfer, |
669a5db4 JG |
396 | |
397 | .irq_handler = ata_interrupt, | |
398 | .irq_clear = ata_bmdma_irq_clear, | |
246ce3b6 | 399 | .irq_on = ata_irq_on, |
669a5db4 | 400 | |
81ad1837 | 401 | .port_start = ata_sff_port_start, |
669a5db4 JG |
402 | }; |
403 | ||
404 | static struct ata_port_operations optiplus_port_ops = { | |
669a5db4 JG |
405 | .set_piomode = optiplus_set_pio_mode, |
406 | .set_dmamode = optiplus_set_dma_mode, | |
407 | ||
408 | .tf_load = ata_tf_load, | |
409 | .tf_read = ata_tf_read, | |
410 | .check_status = ata_check_status, | |
411 | .exec_command = ata_exec_command, | |
412 | .dev_select = ata_std_dev_select, | |
413 | ||
414 | .freeze = ata_bmdma_freeze, | |
415 | .thaw = ata_bmdma_thaw, | |
416 | .post_internal_cmd = ata_bmdma_post_internal_cmd, | |
417 | .error_handler = optidma_error_handler, | |
5c25bf0d AC |
418 | .set_mode = optidma_set_mode, |
419 | .cable_detect = ata_cable_40wire, | |
669a5db4 JG |
420 | |
421 | .bmdma_setup = ata_bmdma_setup, | |
422 | .bmdma_start = ata_bmdma_start, | |
423 | .bmdma_stop = ata_bmdma_stop, | |
424 | .bmdma_status = ata_bmdma_status, | |
425 | ||
426 | .qc_prep = ata_qc_prep, | |
427 | .qc_issue = ata_qc_issue_prot, | |
bda30288 | 428 | |
0d5ff566 | 429 | .data_xfer = ata_data_xfer, |
669a5db4 JG |
430 | |
431 | .irq_handler = ata_interrupt, | |
432 | .irq_clear = ata_bmdma_irq_clear, | |
246ce3b6 | 433 | .irq_on = ata_irq_on, |
669a5db4 | 434 | |
81ad1837 | 435 | .port_start = ata_sff_port_start, |
669a5db4 JG |
436 | }; |
437 | ||
438 | /** | |
439 | * optiplus_with_udma - Look for UDMA capable setup | |
440 | * @pdev; ATA controller | |
441 | */ | |
85cd7251 | 442 | |
669a5db4 JG |
443 | static int optiplus_with_udma(struct pci_dev *pdev) |
444 | { | |
445 | u8 r; | |
446 | int ret = 0; | |
447 | int ioport = 0x22; | |
448 | struct pci_dev *dev1; | |
85cd7251 | 449 | |
669a5db4 JG |
450 | /* Find function 1 */ |
451 | dev1 = pci_get_device(0x1045, 0xC701, NULL); | |
b447916e | 452 | if (dev1 == NULL) |
669a5db4 | 453 | return 0; |
85cd7251 | 454 | |
669a5db4 JG |
455 | /* Rev must be >= 0x10 */ |
456 | pci_read_config_byte(dev1, 0x08, &r); | |
457 | if (r < 0x10) | |
458 | goto done_nomsg; | |
459 | /* Read the chipset system configuration to check our mode */ | |
460 | pci_read_config_byte(dev1, 0x5F, &r); | |
461 | ioport |= (r << 8); | |
462 | outb(0x10, ioport); | |
463 | /* Must be 66Mhz sync */ | |
464 | if ((inb(ioport + 2) & 1) == 0) | |
465 | goto done; | |
466 | ||
467 | /* Check the ATA arbitration/timing is suitable */ | |
468 | pci_read_config_byte(pdev, 0x42, &r); | |
469 | if ((r & 0x36) != 0x36) | |
470 | goto done; | |
471 | pci_read_config_byte(dev1, 0x52, &r); | |
472 | if (r & 0x80) /* IDEDIR disabled */ | |
473 | ret = 1; | |
85cd7251 | 474 | done: |
669a5db4 JG |
475 | printk(KERN_WARNING "UDMA not supported in this configuration.\n"); |
476 | done_nomsg: /* Wrong chip revision */ | |
477 | pci_dev_put(dev1); | |
478 | return ret; | |
479 | } | |
480 | ||
481 | static int optidma_init_one(struct pci_dev *dev, const struct pci_device_id *id) | |
482 | { | |
1626aeb8 | 483 | static const struct ata_port_info info_82c700 = { |
669a5db4 | 484 | .sht = &optidma_sht, |
1d2808fd | 485 | .flags = ATA_FLAG_SLAVE_POSS, |
669a5db4 JG |
486 | .pio_mask = 0x1f, |
487 | .mwdma_mask = 0x07, | |
488 | .port_ops = &optidma_port_ops | |
489 | }; | |
1626aeb8 | 490 | static const struct ata_port_info info_82c700_udma = { |
669a5db4 | 491 | .sht = &optidma_sht, |
1d2808fd | 492 | .flags = ATA_FLAG_SLAVE_POSS, |
669a5db4 JG |
493 | .pio_mask = 0x1f, |
494 | .mwdma_mask = 0x07, | |
495 | .udma_mask = 0x07, | |
496 | .port_ops = &optiplus_port_ops | |
497 | }; | |
1626aeb8 | 498 | const struct ata_port_info *ppi[] = { &info_82c700, NULL }; |
669a5db4 JG |
499 | static int printed_version; |
500 | ||
501 | if (!printed_version++) | |
502 | dev_printk(KERN_DEBUG, &dev->dev, "version " DRV_VERSION "\n"); | |
503 | ||
504 | /* Fixed location chipset magic */ | |
505 | inw(0x1F1); | |
506 | inw(0x1F1); | |
507 | pci_clock = inb(0x1F5) & 1; /* 0 = 33Mhz, 1 = 25Mhz */ | |
85cd7251 | 508 | |
669a5db4 | 509 | if (optiplus_with_udma(dev)) |
1626aeb8 | 510 | ppi[0] = &info_82c700_udma; |
669a5db4 | 511 | |
1626aeb8 | 512 | return ata_pci_init_one(dev, ppi); |
669a5db4 JG |
513 | } |
514 | ||
515 | static const struct pci_device_id optidma[] = { | |
2d2744fc JG |
516 | { PCI_VDEVICE(OPTI, 0xD568), }, /* Opti 82C700 */ |
517 | ||
518 | { }, | |
669a5db4 JG |
519 | }; |
520 | ||
521 | static struct pci_driver optidma_pci_driver = { | |
2d2744fc | 522 | .name = DRV_NAME, |
669a5db4 JG |
523 | .id_table = optidma, |
524 | .probe = optidma_init_one, | |
30ced0f0 | 525 | .remove = ata_pci_remove_one, |
438ac6d5 | 526 | #ifdef CONFIG_PM |
30ced0f0 A |
527 | .suspend = ata_pci_device_suspend, |
528 | .resume = ata_pci_device_resume, | |
438ac6d5 | 529 | #endif |
669a5db4 JG |
530 | }; |
531 | ||
532 | static int __init optidma_init(void) | |
533 | { | |
534 | return pci_register_driver(&optidma_pci_driver); | |
535 | } | |
536 | ||
669a5db4 JG |
537 | static void __exit optidma_exit(void) |
538 | { | |
539 | pci_unregister_driver(&optidma_pci_driver); | |
540 | } | |
541 | ||
669a5db4 JG |
542 | MODULE_AUTHOR("Alan Cox"); |
543 | MODULE_DESCRIPTION("low-level driver for Opti Firestar/Firestar Plus"); | |
544 | MODULE_LICENSE("GPL"); | |
545 | MODULE_DEVICE_TABLE(pci, optidma); | |
546 | MODULE_VERSION(DRV_VERSION); | |
547 | ||
548 | module_init(optidma_init); | |
549 | module_exit(optidma_exit); |