[deliverable/linux.git] / drivers / ata / pata_sl82c105.c

/*
 * pata_sl82c105.c 	- SL82C105 PATA for new ATA layer
 *			  (C) 2005 Red Hat Inc
 *			  Alan Cox <alan@redhat.com>
 *
 * Based in part on linux/drivers/ide/pci/sl82c105.c
 * 		SL82C105/Winbond 553 IDE driver
 *
 * and in part on the documentation and errata sheet
 *
 *
 * Note: The controller like many controllers has shared timings for
 * PIO and DMA. We thus flip to the DMA timings in dma_start and flip back
 * in the dma_stop function. Thus we actually don't need a set_dmamode
 * method as the PIO method is always called and will set the right PIO
 * timing parameters.
 */

#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>

#define DRV_NAME "pata_sl82c105"
#define DRV_VERSION "0.3.0"

enum {
	/*
	 * SL82C105 PCI config register 0x40 bits.
	 */
	CTRL_IDE_IRQB	=	(1 << 30),
	CTRL_IDE_IRQA   =	(1 << 28),
	CTRL_LEGIRQ     =	(1 << 11),
	CTRL_P1F16      =	(1 << 5),
	CTRL_P1EN       =	(1 << 4),
	CTRL_P0F16      =	(1 << 1),
	CTRL_P0EN       =	(1 << 0)
};

/**
 *	sl82c105_pre_reset		-	probe begin
 *	@ap: ATA port
 *
 *	Set up cable type and use generic probe init
 */

static int sl82c105_pre_reset(struct ata_port *ap)
{
	static const struct pci_bits sl82c105_enable_bits[] = {
		{ 0x40, 1, 0x01, 0x01 },
		{ 0x40, 1, 0x10, 0x10 }
	};
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);

	if (ap->port_no && !pci_test_config_bits(pdev, &sl82c105_enable_bits[ap->port_no]))
		return -ENOENT;
	ap->cbl = ATA_CBL_PATA40;
	return ata_std_prereset(ap);
}


static void sl82c105_error_handler(struct ata_port *ap)
{
	ata_bmdma_drive_eh(ap, sl82c105_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
}


/**
 *	sl82c105_configure_piomode	-	set chip PIO timing
 *	@ap: ATA interface
 *	@adev: ATA device
 *	@pio: PIO mode
 *
 *	Called to do the PIO mode setup. Our timing registers are shared
 *	so a configure_dmamode call will undo any work we do here and vice
 *	versa
 */

static void sl82c105_configure_piomode(struct ata_port *ap, struct ata_device *adev, int pio)
{
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	static u16 pio_timing[5] = {
		0x50D, 0x407, 0x304, 0x242, 0x240
	};
	u16 dummy;
	int timing = 0x44 + (8 * ap->port_no) + (4 * adev->devno);

	pci_write_config_word(pdev, timing, pio_timing[pio]);
	/* Can we lose this oddity of the old driver */
	pci_read_config_word(pdev, timing, &dummy);
}

/**
 *	sl82c105_set_piomode	-	set initial PIO mode data
 *	@ap: ATA interface
 *	@adev: ATA device
 *
 *	Called to do the PIO mode setup. Our timing registers are shared
 *	but we want to set the PIO timing by default.
 */

static void sl82c105_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
	sl82c105_configure_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);
}

/**
 *	sl82c105_configure_dmamode	-	set DMA mode in chip
 *	@ap: ATA interface
 *	@adev: ATA device
 *
 *	Load DMA cycle times into the chip ready for a DMA transfer
 *	to occur.
 */

static void sl82c105_configure_dmamode(struct ata_port *ap, struct ata_device *adev)
{
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	static u16 dma_timing[3] = {
		0x707, 0x201, 0x200
	};
	u16 dummy;
	int timing = 0x44 + (8 * ap->port_no) + (4 * adev->devno);
	int dma = adev->dma_mode - XFER_MW_DMA_0;

	pci_write_config_word(pdev, timing, dma_timing[dma]);
	/* Can we lose this oddity of the old driver */
	pci_read_config_word(pdev, timing, &dummy);
}

/**
 *	sl82c105_reset_engine	-	Reset the DMA engine
 *	@ap: ATA interface
 *
 *	The sl82c105 has some serious problems with the DMA engine
 *	when transfers don't run as expected or ATAPI is used. The
 *	recommended fix is to reset the engine each use using a chip
 *	test register.
 */

static void sl82c105_reset_engine(struct ata_port *ap)
{
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	u16 val;

	pci_read_config_word(pdev, 0x7E, &val);
	pci_write_config_word(pdev, 0x7E, val | 4);
	pci_write_config_word(pdev, 0x7E, val & ~4);
}

/**
 *	sl82c105_bmdma_start		-	DMA engine begin
 *	@qc: ATA command
 *
 *	Reset the DMA engine each use as recommended by the errata
 *	document.
 *
 *	FIXME: if we switch clock at BMDMA start/end we might get better
 *	PIO performance on DMA capable devices.
 */

static void sl82c105_bmdma_start(struct ata_queued_cmd *qc)
{
	struct ata_port *ap = qc->ap;

	udelay(100);
	sl82c105_reset_engine(ap);
	udelay(100);

	/* Set the clocks for DMA */
	sl82c105_configure_dmamode(ap, qc->dev);
	/* Activate DMA */
	ata_bmdma_start(qc);
}

/**
 *	sl82c105_bmdma_end		-	DMA engine stop
 *	@qc: ATA command
 *
 *	Reset the DMA engine each use as recommended by the errata
 *	document.
 *
 *	This function is also called to turn off DMA when a timeout occurs
 *	during DMA operation. In both cases we need to reset the engine,
 *	so no actual eng_timeout handler is required.
 *
 *	We assume bmdma_stop is always called if bmdma_start as called. If
 *	not then we may need to wrap qc_issue.
 */

static void sl82c105_bmdma_stop(struct ata_queued_cmd *qc)
{
	struct ata_port *ap = qc->ap;

	ata_bmdma_stop(qc);
	sl82c105_reset_engine(ap);
	udelay(100);

	/* This will redo the initial setup of the DMA device to matching
	   PIO timings */
	sl82c105_set_piomode(ap, qc->dev);
}

static struct scsi_host_template sl82c105_sht = {
	.module			= THIS_MODULE,
	.name			= DRV_NAME,
	.ioctl			= ata_scsi_ioctl,
	.queuecommand		= ata_scsi_queuecmd,
	.can_queue		= ATA_DEF_QUEUE,
	.this_id		= ATA_SHT_THIS_ID,
	.sg_tablesize		= LIBATA_MAX_PRD,
	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
	.emulated		= ATA_SHT_EMULATED,
	.use_clustering		= ATA_SHT_USE_CLUSTERING,
	.proc_name		= DRV_NAME,
	.dma_boundary		= ATA_DMA_BOUNDARY,
	.slave_configure	= ata_scsi_slave_config,
	.slave_destroy		= ata_scsi_slave_destroy,
	.bios_param		= ata_std_bios_param,
};

static struct ata_port_operations sl82c105_port_ops = {
	.port_disable	= ata_port_disable,
	.set_piomode	= sl82c105_set_piomode,
	.mode_filter	= ata_pci_default_filter,

	.tf_load	= ata_tf_load,
	.tf_read	= ata_tf_read,
	.check_status 	= ata_check_status,
	.exec_command	= ata_exec_command,
	.dev_select 	= ata_std_dev_select,

	.error_handler	= sl82c105_error_handler,

	.bmdma_setup 	= ata_bmdma_setup,
	.bmdma_start 	= sl82c105_bmdma_start,
	.bmdma_stop	= sl82c105_bmdma_stop,
	.bmdma_status 	= ata_bmdma_status,

	.qc_prep 	= ata_qc_prep,
	.qc_issue	= ata_qc_issue_prot,

	.data_xfer	= ata_data_xfer,

	.irq_handler	= ata_interrupt,
	.irq_clear	= ata_bmdma_irq_clear,
	.irq_on		= ata_irq_on,
	.irq_ack	= ata_irq_ack,

	.port_start	= ata_port_start,
};

/**
 *	sl82c105_bridge_revision	-	find bridge version
 *	@pdev: PCI device for the ATA function
 *
 *	Locates the PCI bridge associated with the ATA function and
 *	providing it is a Winbond 553 reports the revision. If it cannot
 *	find a revision or the right device it returns -1
 */

static int sl82c105_bridge_revision(struct pci_dev *pdev)
{
	struct pci_dev *bridge;
	u8 rev;

	/*
	 * The bridge should be part of the same device, but function 0.
	 */
	bridge = pci_get_slot(pdev->bus,
			       PCI_DEVFN(PCI_SLOT(pdev->devfn), 0));
	if (!bridge)
		return -1;

	/*
	 * Make sure it is a Winbond 553 and is an ISA bridge.
	 */
	if (bridge->vendor != PCI_VENDOR_ID_WINBOND ||
	    bridge->device != PCI_DEVICE_ID_WINBOND_83C553 ||
	    bridge->class >> 8 != PCI_CLASS_BRIDGE_ISA) {
	    	pci_dev_put(bridge);
		return -1;
	}
	/*
	 * We need to find function 0's revision, not function 1
	 */
	pci_read_config_byte(bridge, PCI_REVISION_ID, &rev);

	pci_dev_put(bridge);
	return rev;
}


static int sl82c105_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
	static struct ata_port_info info_dma = {
		.sht = &sl82c105_sht,
		.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
		.pio_mask = 0x1f,
		.mwdma_mask = 0x07,
		.port_ops = &sl82c105_port_ops
	};
	static struct ata_port_info info_early = {
		.sht = &sl82c105_sht,
		.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
		.pio_mask = 0x1f,
		.port_ops = &sl82c105_port_ops
	};
	static struct ata_port_info *port_info[2] = { &info_early, &info_early };
	u32 val;
	int rev;

	rev = sl82c105_bridge_revision(dev);

	if (rev == -1)
		dev_printk(KERN_WARNING, &dev->dev, "pata_sl82c105: Unable to find bridge, disabling DMA.\n");
	else if (rev <= 5)
		dev_printk(KERN_WARNING, &dev->dev, "pata_sl82c105: Early bridge revision, no DMA available.\n");
	else {
		port_info[0] = &info_dma;
		port_info[1] = &info_dma;
	}

	pci_read_config_dword(dev, 0x40, &val);
	val |= CTRL_P0EN | CTRL_P0F16 | CTRL_P1F16;
	pci_write_config_dword(dev, 0x40, val);


	return ata_pci_init_one(dev, port_info, 1); /* For now */
}

static const struct pci_device_id sl82c105[] = {
	{ PCI_VDEVICE(WINBOND, PCI_DEVICE_ID_WINBOND_82C105), },

	{ },
};

static struct pci_driver sl82c105_pci_driver = {
	.name 		= DRV_NAME,
	.id_table	= sl82c105,
	.probe 		= sl82c105_init_one,
	.remove		= ata_pci_remove_one
};

static int __init sl82c105_init(void)
{
	return pci_register_driver(&sl82c105_pci_driver);
}

static void __exit sl82c105_exit(void)
{
	pci_unregister_driver(&sl82c105_pci_driver);
}

MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Sl82c105");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, sl82c105);
MODULE_VERSION(DRV_VERSION);

module_init(sl82c105_init);
module_exit(sl82c105_exit);
Commit	Line	Data
669a5db4 JG	1	/*
	2	* pata_sl82c105.c - SL82C105 PATA for new ATA layer
	3	* (C) 2005 Red Hat Inc
	4	* Alan Cox <alan@redhat.com>
	5	*
	6	* Based in part on linux/drivers/ide/pci/sl82c105.c
	7	* SL82C105/Winbond 553 IDE driver
	8	*
	9	* and in part on the documentation and errata sheet
16728da9 A	10	*
	11	*
	12	* Note: The controller like many controllers has shared timings for
	13	* PIO and DMA. We thus flip to the DMA timings in dma_start and flip back
	14	* in the dma_stop function. Thus we actually don't need a set_dmamode
	15	* method as the PIO method is always called and will set the right PIO
	16	* timing parameters.
669a5db4	17	*/
85cd7251	18
669a5db4 JG	19	#include <linux/kernel.h>
	20	#include <linux/module.h>
	21	#include <linux/pci.h>
	22	#include <linux/init.h>
	23	#include <linux/blkdev.h>
	24	#include <linux/delay.h>
	25	#include <scsi/scsi_host.h>
	26	#include <linux/libata.h>
	27
	28	#define DRV_NAME "pata_sl82c105"
cb48cab7	29	#define DRV_VERSION "0.3.0"
669a5db4 JG	30
	31	enum {
	32	/*
	33	* SL82C105 PCI config register 0x40 bits.
	34	*/
	35	CTRL_IDE_IRQB = (1 << 30),
	36	CTRL_IDE_IRQA = (1 << 28),
	37	CTRL_LEGIRQ = (1 << 11),
	38	CTRL_P1F16 = (1 << 5),
	39	CTRL_P1EN = (1 << 4),
	40	CTRL_P0F16 = (1 << 1),
	41	CTRL_P0EN = (1 << 0)
	42	};
	43
	44	/**
	45	* sl82c105_pre_reset - probe begin
	46	* @ap: ATA port
	47	*
	48	* Set up cable type and use generic probe init
	49	*/
85cd7251	50
669a5db4 JG	51	static int sl82c105_pre_reset(struct ata_port *ap)
	52	{
	53	static const struct pci_bits sl82c105_enable_bits[] = {
	54	{ 0x40, 1, 0x01, 0x01 },
	55	{ 0x40, 1, 0x10, 0x10 }
	56	};
	57	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	58
c961922b AC	59	if (ap->port_no && !pci_test_config_bits(pdev, &sl82c105_enable_bits[ap->port_no]))
c961922b AC	60	return -ENOENT;
669a5db4 JG	61	ap->cbl = ATA_CBL_PATA40;
	62	return ata_std_prereset(ap);
	63	}
	64
	65
	66	static void sl82c105_error_handler(struct ata_port *ap)
	67	{
	68	ata_bmdma_drive_eh(ap, sl82c105_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
	69	}
	70
	71
	72	/**
	73	* sl82c105_configure_piomode - set chip PIO timing
	74	* @ap: ATA interface
	75	* @adev: ATA device
	76	* @pio: PIO mode
	77	*
	78	* Called to do the PIO mode setup. Our timing registers are shared
	79	* so a configure_dmamode call will undo any work we do here and vice
	80	* versa
	81	*/
85cd7251	82
669a5db4 JG	83	static void sl82c105_configure_piomode(struct ata_port ap, struct ata_device adev, int pio)
	84	{
	85	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	86	static u16 pio_timing[5] = {
	87	0x50D, 0x407, 0x304, 0x242, 0x240
	88	};
	89	u16 dummy;
	90	int timing = 0x44 + (8 * ap->port_no) + (4 * adev->devno);
85cd7251	91
669a5db4 JG	92	pci_write_config_word(pdev, timing, pio_timing[pio]);
	93	/* Can we lose this oddity of the old driver */
	94	pci_read_config_word(pdev, timing, &dummy);
	95	}
	96
	97	/**
	98	* sl82c105_set_piomode - set initial PIO mode data
	99	* @ap: ATA interface
	100	* @adev: ATA device
	101	*
	102	* Called to do the PIO mode setup. Our timing registers are shared
	103	* but we want to set the PIO timing by default.
	104	*/
85cd7251	105
669a5db4 JG	106	static void sl82c105_set_piomode(struct ata_port ap, struct ata_device adev)
	107	{
	108	sl82c105_configure_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);
	109	}
	110
	111	/**
	112	* sl82c105_configure_dmamode - set DMA mode in chip
	113	* @ap: ATA interface
	114	* @adev: ATA device
	115	*
	116	* Load DMA cycle times into the chip ready for a DMA transfer
	117	* to occur.
	118	*/
85cd7251	119
669a5db4 JG	120	static void sl82c105_configure_dmamode(struct ata_port ap, struct ata_device adev)
	121	{
	122	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	123	static u16 dma_timing[3] = {
	124	0x707, 0x201, 0x200
	125	};
	126	u16 dummy;
	127	int timing = 0x44 + (8 * ap->port_no) + (4 * adev->devno);
	128	int dma = adev->dma_mode - XFER_MW_DMA_0;
85cd7251	129
669a5db4 JG	130	pci_write_config_word(pdev, timing, dma_timing[dma]);
	131	/* Can we lose this oddity of the old driver */
	132	pci_read_config_word(pdev, timing, &dummy);
	133	}
	134
669a5db4 JG	135	/**
	136	* sl82c105_reset_engine - Reset the DMA engine
	137	* @ap: ATA interface
	138	*
	139	* The sl82c105 has some serious problems with the DMA engine
85cd7251	140	* when transfers don't run as expected or ATAPI is used. The
669a5db4 JG	141	* recommended fix is to reset the engine each use using a chip
	142	* test register.
	143	*/
85cd7251	144
669a5db4 JG	145	static void sl82c105_reset_engine(struct ata_port *ap)
	146	{
	147	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	148	u16 val;
85cd7251	149
669a5db4 JG	150	pci_read_config_word(pdev, 0x7E, &val);
	151	pci_write_config_word(pdev, 0x7E, val \| 4);
	152	pci_write_config_word(pdev, 0x7E, val & ~4);
	153	}
	154
	155	/**
	156	* sl82c105_bmdma_start - DMA engine begin
	157	* @qc: ATA command
	158	*
	159	* Reset the DMA engine each use as recommended by the errata
85cd7251	160	* document.
669a5db4 JG	161	*
	162	* FIXME: if we switch clock at BMDMA start/end we might get better
	163	* PIO performance on DMA capable devices.
	164	*/
85cd7251	165
669a5db4 JG	166	static void sl82c105_bmdma_start(struct ata_queued_cmd *qc)
	167	{
	168	struct ata_port *ap = qc->ap;
	169
8361cd79	170	udelay(100);
669a5db4	171	sl82c105_reset_engine(ap);
8361cd79	172	udelay(100);
85cd7251	173
669a5db4 JG	174	/* Set the clocks for DMA */
669a5db4 JG	175	sl82c105_configure_dmamode(ap, qc->dev);
85cd7251	176	/* Activate DMA */
669a5db4 JG	177	ata_bmdma_start(qc);
	178	}
	179
	180	/**
	181	* sl82c105_bmdma_end - DMA engine stop
	182	* @qc: ATA command
	183	*
	184	* Reset the DMA engine each use as recommended by the errata
	185	* document.
	186	*
	187	* This function is also called to turn off DMA when a timeout occurs
	188	* during DMA operation. In both cases we need to reset the engine,
	189	* so no actual eng_timeout handler is required.
	190	*
	191	* We assume bmdma_stop is always called if bmdma_start as called. If
	192	* not then we may need to wrap qc_issue.
	193	*/
85cd7251	194
669a5db4 JG	195	static void sl82c105_bmdma_stop(struct ata_queued_cmd *qc)
	196	{
	197	struct ata_port *ap = qc->ap;
	198
	199	ata_bmdma_stop(qc);
	200	sl82c105_reset_engine(ap);
8361cd79	201	udelay(100);
85cd7251	202
669a5db4 JG	203	/* This will redo the initial setup of the DMA device to matching
669a5db4 JG	204	PIO timings */
16728da9	205	sl82c105_set_piomode(ap, qc->dev);
669a5db4 JG	206	}
	207
	208	static struct scsi_host_template sl82c105_sht = {
	209	.module = THIS_MODULE,
	210	.name = DRV_NAME,
	211	.ioctl = ata_scsi_ioctl,
	212	.queuecommand = ata_scsi_queuecmd,
	213	.can_queue = ATA_DEF_QUEUE,
	214	.this_id = ATA_SHT_THIS_ID,
	215	.sg_tablesize = LIBATA_MAX_PRD,
669a5db4 JG	216	.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
	217	.emulated = ATA_SHT_EMULATED,
	218	.use_clustering = ATA_SHT_USE_CLUSTERING,
	219	.proc_name = DRV_NAME,
	220	.dma_boundary = ATA_DMA_BOUNDARY,
	221	.slave_configure = ata_scsi_slave_config,
afdfe899	222	.slave_destroy = ata_scsi_slave_destroy,
669a5db4 JG	223	.bios_param = ata_std_bios_param,
	224	};
	225
	226	static struct ata_port_operations sl82c105_port_ops = {
	227	.port_disable = ata_port_disable,
	228	.set_piomode = sl82c105_set_piomode,
669a5db4 JG	229	.mode_filter = ata_pci_default_filter,
	230
	231	.tf_load = ata_tf_load,
	232	.tf_read = ata_tf_read,
	233	.check_status = ata_check_status,
	234	.exec_command = ata_exec_command,
	235	.dev_select = ata_std_dev_select,
	236
	237	.error_handler = sl82c105_error_handler,
	238
	239	.bmdma_setup = ata_bmdma_setup,
	240	.bmdma_start = sl82c105_bmdma_start,
	241	.bmdma_stop = sl82c105_bmdma_stop,
	242	.bmdma_status = ata_bmdma_status,
	243
	244	.qc_prep = ata_qc_prep,
	245	.qc_issue = ata_qc_issue_prot,
bda30288	246
0d5ff566	247	.data_xfer = ata_data_xfer,
669a5db4 JG	248
	249	.irq_handler = ata_interrupt,
	250	.irq_clear = ata_bmdma_irq_clear,
246ce3b6 AI	251	.irq_on = ata_irq_on,
246ce3b6 AI	252	.irq_ack = ata_irq_ack,
85cd7251	253
669a5db4	254	.port_start = ata_port_start,
85cd7251	255	};
669a5db4 JG	256
	257	/**
	258	* sl82c105_bridge_revision - find bridge version
	259	* @pdev: PCI device for the ATA function
	260	*
	261	* Locates the PCI bridge associated with the ATA function and
	262	* providing it is a Winbond 553 reports the revision. If it cannot
	263	* find a revision or the right device it returns -1
	264	*/
85cd7251	265
669a5db4 JG	266	static int sl82c105_bridge_revision(struct pci_dev *pdev)
	267	{
	268	struct pci_dev *bridge;
	269	u8 rev;
	270
	271	/*
	272	* The bridge should be part of the same device, but function 0.
	273	*/
	274	bridge = pci_get_slot(pdev->bus,
	275	PCI_DEVFN(PCI_SLOT(pdev->devfn), 0));
	276	if (!bridge)
	277	return -1;
	278
	279	/*
	280	* Make sure it is a Winbond 553 and is an ISA bridge.
	281	*/
	282	if (bridge->vendor != PCI_VENDOR_ID_WINBOND \|\|
	283	bridge->device != PCI_DEVICE_ID_WINBOND_83C553 \|\|
	284	bridge->class >> 8 != PCI_CLASS_BRIDGE_ISA) {
	285	pci_dev_put(bridge);
	286	return -1;
	287	}
	288	/*
	289	* We need to find function 0's revision, not function 1
	290	*/
	291	pci_read_config_byte(bridge, PCI_REVISION_ID, &rev);
	292
	293	pci_dev_put(bridge);
	294	return rev;
	295	}
	296
85cd7251	297
669a5db4 JG	298	static int sl82c105_init_one(struct pci_dev dev, const struct pci_device_id id)
	299	{
	300	static struct ata_port_info info_dma = {
	301	.sht = &sl82c105_sht,
	302	.flags = ATA_FLAG_SLAVE_POSS \| ATA_FLAG_SRST,
	303	.pio_mask = 0x1f,
	304	.mwdma_mask = 0x07,
	305	.port_ops = &sl82c105_port_ops
	306	};
	307	static struct ata_port_info info_early = {
	308	.sht = &sl82c105_sht,
	309	.flags = ATA_FLAG_SLAVE_POSS \| ATA_FLAG_SRST,
	310	.pio_mask = 0x1f,
	311	.port_ops = &sl82c105_port_ops
	312	};
	313	static struct ata_port_info *port_info[2] = { &info_early, &info_early };
	314	u32 val;
	315	int rev;
	316
	317	rev = sl82c105_bridge_revision(dev);
85cd7251	318
669a5db4 JG	319	if (rev == -1)
	320	dev_printk(KERN_WARNING, &dev->dev, "pata_sl82c105: Unable to find bridge, disabling DMA.\n");
	321	else if (rev <= 5)
	322	dev_printk(KERN_WARNING, &dev->dev, "pata_sl82c105: Early bridge revision, no DMA available.\n");
	323	else {
	324	port_info[0] = &info_dma;
	325	port_info[1] = &info_dma;
	326	}
85cd7251	327
669a5db4 JG	328	pci_read_config_dword(dev, 0x40, &val);
	329	val \|= CTRL_P0EN \| CTRL_P0F16 \| CTRL_P1F16;
	330	pci_write_config_dword(dev, 0x40, val);
	331
	332
	333	return ata_pci_init_one(dev, port_info, 1); /* For now */
	334	}
	335
2d2744fc JG	336	static const struct pci_device_id sl82c105[] = {
	337	{ PCI_VDEVICE(WINBOND, PCI_DEVICE_ID_WINBOND_82C105), },
	338
	339	{ },
669a5db4 JG	340	};
	341
	342	static struct pci_driver sl82c105_pci_driver = {
	343	.name = DRV_NAME,
	344	.id_table = sl82c105,
	345	.probe = sl82c105_init_one,
	346	.remove = ata_pci_remove_one
	347	};
	348
	349	static int __init sl82c105_init(void)
	350	{
	351	return pci_register_driver(&sl82c105_pci_driver);
	352	}
	353
669a5db4 JG	354	static void __exit sl82c105_exit(void)
	355	{
	356	pci_unregister_driver(&sl82c105_pci_driver);
	357	}
	358
669a5db4 JG	359	MODULE_AUTHOR("Alan Cox");
	360	MODULE_DESCRIPTION("low-level driver for Sl82c105");
	361	MODULE_LICENSE("GPL");
	362	MODULE_DEVICE_TABLE(pci, sl82c105);
	363	MODULE_VERSION(DRV_VERSION);
	364
	365	module_init(sl82c105_init);
	366	module_exit(sl82c105_exit);