Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | /* |
2 | * A driver for the Griffin Technology, Inc. "PowerMate" USB controller dial. | |
3 | * | |
4 | * v1.1, (c)2002 William R Sowerbutts <will@sowerbutts.com> | |
5 | * | |
6 | * This device is a anodised aluminium knob which connects over USB. It can measure | |
7 | * clockwise and anticlockwise rotation. The dial also acts as a pushbutton with | |
8 | * a spring for automatic release. The base contains a pair of LEDs which illuminate | |
9 | * the translucent base. It rotates without limit and reports its relative rotation | |
10 | * back to the host when polled by the USB controller. | |
11 | * | |
12 | * Testing with the knob I have has shown that it measures approximately 94 "clicks" | |
05f091ab | 13 | * for one full rotation. Testing with my High Speed Rotation Actuator (ok, it was |
1da177e4 LT |
14 | * a variable speed cordless electric drill) has shown that the device can measure |
15 | * speeds of up to 7 clicks either clockwise or anticlockwise between pollings from | |
16 | * the host. If it counts more than 7 clicks before it is polled, it will wrap back | |
17 | * to zero and start counting again. This was at quite high speed, however, almost | |
18 | * certainly faster than the human hand could turn it. Griffin say that it loses a | |
19 | * pulse or two on a direction change; the granularity is so fine that I never | |
20 | * noticed this in practice. | |
21 | * | |
22 | * The device's microcontroller can be programmed to set the LED to either a constant | |
23 | * intensity, or to a rhythmic pulsing. Several patterns and speeds are available. | |
24 | * | |
25 | * Griffin were very happy to provide documentation and free hardware for development. | |
26 | * | |
27 | * Some userspace tools are available on the web: http://sowerbutts.com/powermate/ | |
28 | * | |
29 | */ | |
30 | ||
31 | #include <linux/kernel.h> | |
32 | #include <linux/slab.h> | |
1da177e4 LT |
33 | #include <linux/module.h> |
34 | #include <linux/init.h> | |
35 | #include <linux/spinlock.h> | |
ae0dadcf | 36 | #include <linux/usb/input.h> |
1da177e4 LT |
37 | |
38 | #define POWERMATE_VENDOR 0x077d /* Griffin Technology, Inc. */ | |
39 | #define POWERMATE_PRODUCT_NEW 0x0410 /* Griffin PowerMate */ | |
40 | #define POWERMATE_PRODUCT_OLD 0x04AA /* Griffin soundKnob */ | |
41 | ||
42 | #define CONTOUR_VENDOR 0x05f3 /* Contour Design, Inc. */ | |
43 | #define CONTOUR_JOG 0x0240 /* Jog and Shuttle */ | |
44 | ||
45 | /* these are the command codes we send to the device */ | |
46 | #define SET_STATIC_BRIGHTNESS 0x01 | |
47 | #define SET_PULSE_ASLEEP 0x02 | |
48 | #define SET_PULSE_AWAKE 0x03 | |
49 | #define SET_PULSE_MODE 0x04 | |
50 | ||
51 | /* these refer to bits in the powermate_device's requires_update field. */ | |
52 | #define UPDATE_STATIC_BRIGHTNESS (1<<0) | |
53 | #define UPDATE_PULSE_ASLEEP (1<<1) | |
54 | #define UPDATE_PULSE_AWAKE (1<<2) | |
55 | #define UPDATE_PULSE_MODE (1<<3) | |
56 | ||
57 | /* at least two versions of the hardware exist, with differing payload | |
58 | sizes. the first three bytes always contain the "interesting" data in | |
59 | the relevant format. */ | |
60 | #define POWERMATE_PAYLOAD_SIZE_MAX 6 | |
61 | #define POWERMATE_PAYLOAD_SIZE_MIN 3 | |
62 | struct powermate_device { | |
63 | signed char *data; | |
64 | dma_addr_t data_dma; | |
65 | struct urb *irq, *config; | |
66 | struct usb_ctrlrequest *configcr; | |
1da177e4 | 67 | struct usb_device *udev; |
c25e6478 | 68 | struct usb_interface *intf; |
c5b7c7c3 | 69 | struct input_dev *input; |
1da177e4 LT |
70 | spinlock_t lock; |
71 | int static_brightness; | |
72 | int pulse_speed; | |
73 | int pulse_table; | |
74 | int pulse_asleep; | |
75 | int pulse_awake; | |
76 | int requires_update; // physical settings which are out of sync | |
77 | char phys[64]; | |
78 | }; | |
79 | ||
80 | static char pm_name_powermate[] = "Griffin PowerMate"; | |
81 | static char pm_name_soundknob[] = "Griffin SoundKnob"; | |
82 | ||
7d12e780 | 83 | static void powermate_config_complete(struct urb *urb); |
1da177e4 LT |
84 | |
85 | /* Callback for data arriving from the PowerMate over the USB interrupt pipe */ | |
7d12e780 | 86 | static void powermate_irq(struct urb *urb) |
1da177e4 LT |
87 | { |
88 | struct powermate_device *pm = urb->context; | |
c25e6478 | 89 | struct device *dev = &pm->intf->dev; |
1da177e4 LT |
90 | int retval; |
91 | ||
92 | switch (urb->status) { | |
93 | case 0: | |
94 | /* success */ | |
95 | break; | |
96 | case -ECONNRESET: | |
97 | case -ENOENT: | |
98 | case -ESHUTDOWN: | |
99 | /* this urb is terminated, clean up */ | |
8b0725c0 GKH |
100 | dev_dbg(dev, "%s - urb shutting down with status: %d\n", |
101 | __func__, urb->status); | |
1da177e4 LT |
102 | return; |
103 | default: | |
8b0725c0 GKH |
104 | dev_dbg(dev, "%s - nonzero urb status received: %d\n", |
105 | __func__, urb->status); | |
1da177e4 LT |
106 | goto exit; |
107 | } | |
108 | ||
109 | /* handle updates to device state */ | |
c5b7c7c3 DT |
110 | input_report_key(pm->input, BTN_0, pm->data[0] & 0x01); |
111 | input_report_rel(pm->input, REL_DIAL, pm->data[1]); | |
112 | input_sync(pm->input); | |
1da177e4 LT |
113 | |
114 | exit: | |
115 | retval = usb_submit_urb (urb, GFP_ATOMIC); | |
116 | if (retval) | |
8b0725c0 | 117 | dev_err(dev, "%s - usb_submit_urb failed with result: %d\n", |
2385f3c3 | 118 | __func__, retval); |
1da177e4 LT |
119 | } |
120 | ||
121 | /* Decide if we need to issue a control message and do so. Must be called with pm->lock taken */ | |
122 | static void powermate_sync_state(struct powermate_device *pm) | |
123 | { | |
05f091ab | 124 | if (pm->requires_update == 0) |
1da177e4 | 125 | return; /* no updates are required */ |
05f091ab | 126 | if (pm->config->status == -EINPROGRESS) |
1da177e4 LT |
127 | return; /* an update is already in progress; it'll issue this update when it completes */ |
128 | ||
129 | if (pm->requires_update & UPDATE_PULSE_ASLEEP){ | |
130 | pm->configcr->wValue = cpu_to_le16( SET_PULSE_ASLEEP ); | |
131 | pm->configcr->wIndex = cpu_to_le16( pm->pulse_asleep ? 1 : 0 ); | |
132 | pm->requires_update &= ~UPDATE_PULSE_ASLEEP; | |
133 | }else if (pm->requires_update & UPDATE_PULSE_AWAKE){ | |
134 | pm->configcr->wValue = cpu_to_le16( SET_PULSE_AWAKE ); | |
135 | pm->configcr->wIndex = cpu_to_le16( pm->pulse_awake ? 1 : 0 ); | |
136 | pm->requires_update &= ~UPDATE_PULSE_AWAKE; | |
137 | }else if (pm->requires_update & UPDATE_PULSE_MODE){ | |
138 | int op, arg; | |
139 | /* the powermate takes an operation and an argument for its pulse algorithm. | |
140 | the operation can be: | |
141 | 0: divide the speed | |
142 | 1: pulse at normal speed | |
143 | 2: multiply the speed | |
144 | the argument only has an effect for operations 0 and 2, and ranges between | |
145 | 1 (least effect) to 255 (maximum effect). | |
05f091ab | 146 | |
1da177e4 LT |
147 | thus, several states are equivalent and are coalesced into one state. |
148 | ||
149 | we map this onto a range from 0 to 510, with: | |
150 | 0 -- 254 -- use divide (0 = slowest) | |
151 | 255 -- use normal speed | |
152 | 256 -- 510 -- use multiple (510 = fastest). | |
153 | ||
154 | Only values of 'arg' quite close to 255 are particularly useful/spectacular. | |
05f091ab | 155 | */ |
c5b7c7c3 | 156 | if (pm->pulse_speed < 255) { |
1da177e4 LT |
157 | op = 0; // divide |
158 | arg = 255 - pm->pulse_speed; | |
c5b7c7c3 | 159 | } else if (pm->pulse_speed > 255) { |
1da177e4 LT |
160 | op = 2; // multiply |
161 | arg = pm->pulse_speed - 255; | |
162 | } else { | |
163 | op = 1; // normal speed | |
164 | arg = 0; // can be any value | |
165 | } | |
166 | pm->configcr->wValue = cpu_to_le16( (pm->pulse_table << 8) | SET_PULSE_MODE ); | |
167 | pm->configcr->wIndex = cpu_to_le16( (arg << 8) | op ); | |
168 | pm->requires_update &= ~UPDATE_PULSE_MODE; | |
c5b7c7c3 | 169 | } else if (pm->requires_update & UPDATE_STATIC_BRIGHTNESS) { |
1da177e4 LT |
170 | pm->configcr->wValue = cpu_to_le16( SET_STATIC_BRIGHTNESS ); |
171 | pm->configcr->wIndex = cpu_to_le16( pm->static_brightness ); | |
172 | pm->requires_update &= ~UPDATE_STATIC_BRIGHTNESS; | |
c5b7c7c3 | 173 | } else { |
1da177e4 LT |
174 | printk(KERN_ERR "powermate: unknown update required"); |
175 | pm->requires_update = 0; /* fudge the bug */ | |
176 | return; | |
177 | } | |
178 | ||
179 | /* printk("powermate: %04x %04x\n", pm->configcr->wValue, pm->configcr->wIndex); */ | |
180 | ||
181 | pm->configcr->bRequestType = 0x41; /* vendor request */ | |
182 | pm->configcr->bRequest = 0x01; | |
183 | pm->configcr->wLength = 0; | |
184 | ||
185 | usb_fill_control_urb(pm->config, pm->udev, usb_sndctrlpipe(pm->udev, 0), | |
186 | (void *) pm->configcr, NULL, 0, | |
187 | powermate_config_complete, pm); | |
1da177e4 LT |
188 | |
189 | if (usb_submit_urb(pm->config, GFP_ATOMIC)) | |
190 | printk(KERN_ERR "powermate: usb_submit_urb(config) failed"); | |
191 | } | |
192 | ||
193 | /* Called when our asynchronous control message completes. We may need to issue another immediately */ | |
7d12e780 | 194 | static void powermate_config_complete(struct urb *urb) |
1da177e4 LT |
195 | { |
196 | struct powermate_device *pm = urb->context; | |
197 | unsigned long flags; | |
198 | ||
199 | if (urb->status) | |
200 | printk(KERN_ERR "powermate: config urb returned %d\n", urb->status); | |
05f091ab | 201 | |
1da177e4 LT |
202 | spin_lock_irqsave(&pm->lock, flags); |
203 | powermate_sync_state(pm); | |
204 | spin_unlock_irqrestore(&pm->lock, flags); | |
205 | } | |
206 | ||
207 | /* Set the LED up as described and begin the sync with the hardware if required */ | |
05f091ab | 208 | static void powermate_pulse_led(struct powermate_device *pm, int static_brightness, int pulse_speed, |
1da177e4 LT |
209 | int pulse_table, int pulse_asleep, int pulse_awake) |
210 | { | |
211 | unsigned long flags; | |
212 | ||
213 | if (pulse_speed < 0) | |
214 | pulse_speed = 0; | |
215 | if (pulse_table < 0) | |
216 | pulse_table = 0; | |
217 | if (pulse_speed > 510) | |
218 | pulse_speed = 510; | |
219 | if (pulse_table > 2) | |
220 | pulse_table = 2; | |
221 | ||
222 | pulse_asleep = !!pulse_asleep; | |
223 | pulse_awake = !!pulse_awake; | |
224 | ||
225 | ||
226 | spin_lock_irqsave(&pm->lock, flags); | |
227 | ||
228 | /* mark state updates which are required */ | |
c5b7c7c3 | 229 | if (static_brightness != pm->static_brightness) { |
1da177e4 | 230 | pm->static_brightness = static_brightness; |
05f091ab | 231 | pm->requires_update |= UPDATE_STATIC_BRIGHTNESS; |
1da177e4 | 232 | } |
c5b7c7c3 | 233 | if (pulse_asleep != pm->pulse_asleep) { |
1da177e4 LT |
234 | pm->pulse_asleep = pulse_asleep; |
235 | pm->requires_update |= (UPDATE_PULSE_ASLEEP | UPDATE_STATIC_BRIGHTNESS); | |
236 | } | |
c5b7c7c3 | 237 | if (pulse_awake != pm->pulse_awake) { |
1da177e4 LT |
238 | pm->pulse_awake = pulse_awake; |
239 | pm->requires_update |= (UPDATE_PULSE_AWAKE | UPDATE_STATIC_BRIGHTNESS); | |
240 | } | |
c5b7c7c3 | 241 | if (pulse_speed != pm->pulse_speed || pulse_table != pm->pulse_table) { |
1da177e4 LT |
242 | pm->pulse_speed = pulse_speed; |
243 | pm->pulse_table = pulse_table; | |
244 | pm->requires_update |= UPDATE_PULSE_MODE; | |
245 | } | |
246 | ||
247 | powermate_sync_state(pm); | |
05f091ab | 248 | |
1da177e4 LT |
249 | spin_unlock_irqrestore(&pm->lock, flags); |
250 | } | |
251 | ||
252 | /* Callback from the Input layer when an event arrives from userspace to configure the LED */ | |
253 | static int powermate_input_event(struct input_dev *dev, unsigned int type, unsigned int code, int _value) | |
254 | { | |
255 | unsigned int command = (unsigned int)_value; | |
7791bdae | 256 | struct powermate_device *pm = input_get_drvdata(dev); |
1da177e4 LT |
257 | |
258 | if (type == EV_MSC && code == MSC_PULSELED){ | |
05f091ab | 259 | /* |
1da177e4 LT |
260 | bits 0- 7: 8 bits: LED brightness |
261 | bits 8-16: 9 bits: pulsing speed modifier (0 ... 510); 0-254 = slower, 255 = standard, 256-510 = faster. | |
262 | bits 17-18: 2 bits: pulse table (0, 1, 2 valid) | |
263 | bit 19: 1 bit : pulse whilst asleep? | |
264 | bit 20: 1 bit : pulse constantly? | |
05f091ab | 265 | */ |
1da177e4 LT |
266 | int static_brightness = command & 0xFF; // bits 0-7 |
267 | int pulse_speed = (command >> 8) & 0x1FF; // bits 8-16 | |
268 | int pulse_table = (command >> 17) & 0x3; // bits 17-18 | |
269 | int pulse_asleep = (command >> 19) & 0x1; // bit 19 | |
270 | int pulse_awake = (command >> 20) & 0x1; // bit 20 | |
05f091ab | 271 | |
1da177e4 LT |
272 | powermate_pulse_led(pm, static_brightness, pulse_speed, pulse_table, pulse_asleep, pulse_awake); |
273 | } | |
274 | ||
275 | return 0; | |
276 | } | |
277 | ||
278 | static int powermate_alloc_buffers(struct usb_device *udev, struct powermate_device *pm) | |
279 | { | |
997ea58e DM |
280 | pm->data = usb_alloc_coherent(udev, POWERMATE_PAYLOAD_SIZE_MAX, |
281 | GFP_ATOMIC, &pm->data_dma); | |
1da177e4 LT |
282 | if (!pm->data) |
283 | return -1; | |
c5b7c7c3 | 284 | |
0ede76fc | 285 | pm->configcr = kmalloc(sizeof(*(pm->configcr)), GFP_KERNEL); |
1da177e4 | 286 | if (!pm->configcr) |
6792cbbb | 287 | return -ENOMEM; |
1da177e4 LT |
288 | |
289 | return 0; | |
290 | } | |
291 | ||
292 | static void powermate_free_buffers(struct usb_device *udev, struct powermate_device *pm) | |
293 | { | |
997ea58e DM |
294 | usb_free_coherent(udev, POWERMATE_PAYLOAD_SIZE_MAX, |
295 | pm->data, pm->data_dma); | |
0ede76fc | 296 | kfree(pm->configcr); |
1da177e4 LT |
297 | } |
298 | ||
299 | /* Called whenever a USB device matching one in our supported devices table is connected */ | |
300 | static int powermate_probe(struct usb_interface *intf, const struct usb_device_id *id) | |
301 | { | |
302 | struct usb_device *udev = interface_to_usbdev (intf); | |
303 | struct usb_host_interface *interface; | |
304 | struct usb_endpoint_descriptor *endpoint; | |
305 | struct powermate_device *pm; | |
c5b7c7c3 | 306 | struct input_dev *input_dev; |
1da177e4 | 307 | int pipe, maxp; |
5014186d | 308 | int error = -ENOMEM; |
1da177e4 LT |
309 | |
310 | interface = intf->cur_altsetting; | |
311 | endpoint = &interface->endpoint[0].desc; | |
60ca126c | 312 | if (!usb_endpoint_is_int_in(endpoint)) |
1da177e4 LT |
313 | return -EIO; |
314 | ||
315 | usb_control_msg(udev, usb_sndctrlpipe(udev, 0), | |
316 | 0x0a, USB_TYPE_CLASS | USB_RECIP_INTERFACE, | |
317 | 0, interface->desc.bInterfaceNumber, NULL, 0, | |
318 | USB_CTRL_SET_TIMEOUT); | |
319 | ||
c5b7c7c3 DT |
320 | pm = kzalloc(sizeof(struct powermate_device), GFP_KERNEL); |
321 | input_dev = input_allocate_device(); | |
322 | if (!pm || !input_dev) | |
323 | goto fail1; | |
1da177e4 | 324 | |
c5b7c7c3 DT |
325 | if (powermate_alloc_buffers(udev, pm)) |
326 | goto fail2; | |
1da177e4 LT |
327 | |
328 | pm->irq = usb_alloc_urb(0, GFP_KERNEL); | |
c5b7c7c3 DT |
329 | if (!pm->irq) |
330 | goto fail2; | |
1da177e4 LT |
331 | |
332 | pm->config = usb_alloc_urb(0, GFP_KERNEL); | |
c5b7c7c3 DT |
333 | if (!pm->config) |
334 | goto fail3; | |
335 | ||
336 | pm->udev = udev; | |
c25e6478 | 337 | pm->intf = intf; |
c5b7c7c3 DT |
338 | pm->input = input_dev; |
339 | ||
340 | usb_make_path(udev, pm->phys, sizeof(pm->phys)); | |
6236dfaa | 341 | strlcat(pm->phys, "/input0", sizeof(pm->phys)); |
1da177e4 LT |
342 | |
343 | spin_lock_init(&pm->lock); | |
c5b7c7c3 DT |
344 | |
345 | switch (le16_to_cpu(udev->descriptor.idProduct)) { | |
346 | case POWERMATE_PRODUCT_NEW: | |
347 | input_dev->name = pm_name_powermate; | |
348 | break; | |
349 | case POWERMATE_PRODUCT_OLD: | |
350 | input_dev->name = pm_name_soundknob; | |
351 | break; | |
352 | default: | |
353 | input_dev->name = pm_name_soundknob; | |
354 | printk(KERN_WARNING "powermate: unknown product id %04x\n", | |
355 | le16_to_cpu(udev->descriptor.idProduct)); | |
356 | } | |
357 | ||
358 | input_dev->phys = pm->phys; | |
359 | usb_to_input_id(udev, &input_dev->id); | |
c0f82d57 | 360 | input_dev->dev.parent = &intf->dev; |
7791bdae DT |
361 | |
362 | input_set_drvdata(input_dev, pm); | |
c5b7c7c3 DT |
363 | |
364 | input_dev->event = powermate_input_event; | |
365 | ||
7b19ada2 JS |
366 | input_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_REL) | |
367 | BIT_MASK(EV_MSC); | |
368 | input_dev->keybit[BIT_WORD(BTN_0)] = BIT_MASK(BTN_0); | |
369 | input_dev->relbit[BIT_WORD(REL_DIAL)] = BIT_MASK(REL_DIAL); | |
370 | input_dev->mscbit[BIT_WORD(MSC_PULSELED)] = BIT_MASK(MSC_PULSELED); | |
1da177e4 LT |
371 | |
372 | /* get a handle to the interrupt data pipe */ | |
373 | pipe = usb_rcvintpipe(udev, endpoint->bEndpointAddress); | |
374 | maxp = usb_maxpacket(udev, pipe, usb_pipeout(pipe)); | |
375 | ||
c5b7c7c3 DT |
376 | if (maxp < POWERMATE_PAYLOAD_SIZE_MIN || maxp > POWERMATE_PAYLOAD_SIZE_MAX) { |
377 | printk(KERN_WARNING "powermate: Expected payload of %d--%d bytes, found %d bytes!\n", | |
1da177e4 LT |
378 | POWERMATE_PAYLOAD_SIZE_MIN, POWERMATE_PAYLOAD_SIZE_MAX, maxp); |
379 | maxp = POWERMATE_PAYLOAD_SIZE_MAX; | |
380 | } | |
381 | ||
382 | usb_fill_int_urb(pm->irq, udev, pipe, pm->data, | |
383 | maxp, powermate_irq, | |
384 | pm, endpoint->bInterval); | |
385 | pm->irq->transfer_dma = pm->data_dma; | |
386 | pm->irq->transfer_flags |= URB_NO_TRANSFER_DMA_MAP; | |
387 | ||
388 | /* register our interrupt URB with the USB system */ | |
389 | if (usb_submit_urb(pm->irq, GFP_KERNEL)) { | |
5014186d | 390 | error = -EIO; |
c5b7c7c3 | 391 | goto fail4; |
1da177e4 LT |
392 | } |
393 | ||
5014186d DT |
394 | error = input_register_device(pm->input); |
395 | if (error) | |
396 | goto fail5; | |
397 | ||
05f091ab | 398 | |
1da177e4 LT |
399 | /* force an update of everything */ |
400 | pm->requires_update = UPDATE_PULSE_ASLEEP | UPDATE_PULSE_AWAKE | UPDATE_PULSE_MODE | UPDATE_STATIC_BRIGHTNESS; | |
401 | powermate_pulse_led(pm, 0x80, 255, 0, 1, 0); // set default pulse parameters | |
05f091ab | 402 | |
1da177e4 LT |
403 | usb_set_intfdata(intf, pm); |
404 | return 0; | |
c5b7c7c3 | 405 | |
5014186d DT |
406 | fail5: usb_kill_urb(pm->irq); |
407 | fail4: usb_free_urb(pm->config); | |
408 | fail3: usb_free_urb(pm->irq); | |
409 | fail2: powermate_free_buffers(udev, pm); | |
410 | fail1: input_free_device(input_dev); | |
c5b7c7c3 | 411 | kfree(pm); |
5014186d | 412 | return error; |
1da177e4 LT |
413 | } |
414 | ||
415 | /* Called when a USB device we've accepted ownership of is removed */ | |
416 | static void powermate_disconnect(struct usb_interface *intf) | |
417 | { | |
418 | struct powermate_device *pm = usb_get_intfdata (intf); | |
419 | ||
420 | usb_set_intfdata(intf, NULL); | |
421 | if (pm) { | |
422 | pm->requires_update = 0; | |
423 | usb_kill_urb(pm->irq); | |
c5b7c7c3 | 424 | input_unregister_device(pm->input); |
1da177e4 LT |
425 | usb_free_urb(pm->irq); |
426 | usb_free_urb(pm->config); | |
427 | powermate_free_buffers(interface_to_usbdev(intf), pm); | |
428 | ||
429 | kfree(pm); | |
430 | } | |
431 | } | |
432 | ||
433 | static struct usb_device_id powermate_devices [] = { | |
434 | { USB_DEVICE(POWERMATE_VENDOR, POWERMATE_PRODUCT_NEW) }, | |
435 | { USB_DEVICE(POWERMATE_VENDOR, POWERMATE_PRODUCT_OLD) }, | |
436 | { USB_DEVICE(CONTOUR_VENDOR, CONTOUR_JOG) }, | |
437 | { } /* Terminating entry */ | |
438 | }; | |
439 | ||
440 | MODULE_DEVICE_TABLE (usb, powermate_devices); | |
441 | ||
442 | static struct usb_driver powermate_driver = { | |
1da177e4 LT |
443 | .name = "powermate", |
444 | .probe = powermate_probe, | |
445 | .disconnect = powermate_disconnect, | |
446 | .id_table = powermate_devices, | |
447 | }; | |
448 | ||
08642e7c | 449 | module_usb_driver(powermate_driver); |
1da177e4 LT |
450 | |
451 | MODULE_AUTHOR( "William R Sowerbutts" ); | |
452 | MODULE_DESCRIPTION( "Griffin Technology, Inc PowerMate driver" ); | |
453 | MODULE_LICENSE("GPL"); |