Commit | Line | Data |
---|---|---|
1da177e4 | 1 | # |
d05e84e6 | 2 | # Touchscreen driver configuration |
1da177e4 LT |
3 | # |
4 | menuconfig INPUT_TOUCHSCREEN | |
5 | bool "Touchscreens" | |
6 | help | |
7 | Say Y here, and a list of supported touchscreens will be displayed. | |
8 | This option doesn't affect the kernel. | |
9 | ||
10 | If unsure, say Y. | |
11 | ||
12 | if INPUT_TOUCHSCREEN | |
13 | ||
ffa458c1 | 14 | config TOUCHSCREEN_ADS7846 |
bff0de5f | 15 | tristate "ADS7846/TSC2046 and ADS7843 based touchscreens" |
ffa458c1 | 16 | depends on SPI_MASTER |
2c8dc071 | 17 | depends on HWMON = n || HWMON |
ffa458c1 DB |
18 | help |
19 | Say Y here if you have a touchscreen interface using the | |
bff0de5f DB |
20 | ADS7846/TSC2046 or ADS7843 controller, and your board-specific |
21 | setup code includes that in its table of SPI devices. | |
ffa458c1 | 22 | |
2c8dc071 DB |
23 | If HWMON is selected, and the driver is told the reference voltage |
24 | on your board, you will also get hwmon interfaces for the voltage | |
bff0de5f | 25 | (and on ads7846/tsc2046, temperature) sensors of this chip. |
2c8dc071 | 26 | |
ffa458c1 DB |
27 | If unsure, say N (but it's safe to say "Y"). |
28 | ||
29 | To compile this driver as a module, choose M here: the | |
30 | module will be called ads7846. | |
31 | ||
1da177e4 LT |
32 | config TOUCHSCREEN_BITSY |
33 | tristate "Compaq iPAQ H3600 (Bitsy) touchscreen" | |
34 | depends on SA1100_BITSY | |
35 | select SERIO | |
36 | help | |
37 | Say Y here if you have the h3600 (Bitsy) touchscreen. | |
38 | ||
39 | If unsure, say N. | |
40 | ||
41 | To compile this driver as a module, choose M here: the | |
42 | module will be called h3600_ts_input. | |
43 | ||
44 | config TOUCHSCREEN_CORGI | |
513b6e1a | 45 | tristate "SharpSL (Corgi and Spitz series) touchscreen driver" |
1da177e4 | 46 | depends on PXA_SHARPSL |
d05e84e6 | 47 | default y |
1da177e4 | 48 | help |
d05e84e6 | 49 | Say Y here to enable the driver for the touchscreen on the |
513b6e1a | 50 | Sharp SL-C7xx and SL-Cxx00 series of PDAs. |
1da177e4 LT |
51 | |
52 | If unsure, say N. | |
53 | ||
54 | To compile this driver as a module, choose M here: the | |
513b6e1a | 55 | module will be called corgi_ts. |
1da177e4 | 56 | |
85f202d5 DT |
57 | config TOUCHSCREEN_FUJITSU |
58 | tristate "Fujitsu serial touchscreen" | |
59 | select SERIO | |
60 | help | |
61 | Say Y here if you have the Fujitsu touchscreen (such as one | |
62 | installed in Lifebook P series laptop) connected to your | |
63 | system. | |
64 | ||
65 | If unsure, say N. | |
66 | ||
67 | To compile this driver as a module, choose M here: the | |
68 | module will be called fujitsu-ts. | |
69 | ||
1da177e4 LT |
70 | config TOUCHSCREEN_GUNZE |
71 | tristate "Gunze AHL-51S touchscreen" | |
72 | select SERIO | |
73 | help | |
74 | Say Y here if you have the Gunze AHL-51 touchscreen connected to | |
75 | your system. | |
76 | ||
77 | If unsure, say N. | |
78 | ||
79 | To compile this driver as a module, choose M here: the | |
80 | module will be called gunze. | |
81 | ||
82 | config TOUCHSCREEN_ELO | |
83 | tristate "Elo serial touchscreens" | |
84 | select SERIO | |
85 | help | |
86 | Say Y here if you have an Elo serial touchscreen connected to | |
87 | your system. | |
88 | ||
89 | If unsure, say N. | |
90 | ||
91 | To compile this driver as a module, choose M here: the | |
153ab429 | 92 | module will be called elo. |
1da177e4 LT |
93 | |
94 | config TOUCHSCREEN_MTOUCH | |
95 | tristate "MicroTouch serial touchscreens" | |
96 | select SERIO | |
97 | help | |
98 | Say Y here if you have a MicroTouch (3M) serial touchscreen connected to | |
99 | your system. | |
100 | ||
101 | If unsure, say N. | |
102 | ||
103 | To compile this driver as a module, choose M here: the | |
104 | module will be called mtouch. | |
105 | ||
3cadd2d9 RL |
106 | config TOUCHSCREEN_INEXIO |
107 | tristate "iNexio serial touchscreens" | |
108 | select SERIO | |
109 | help | |
110 | Say Y here if you have an iNexio serial touchscreen connected to | |
111 | your system. | |
112 | ||
113 | If unsure, say N. | |
114 | ||
115 | To compile this driver as a module, choose M here: the | |
116 | module will be called inexio. | |
117 | ||
1da177e4 LT |
118 | config TOUCHSCREEN_MK712 |
119 | tristate "ICS MicroClock MK712 touchscreen" | |
120 | help | |
121 | Say Y here if you have the ICS MicroClock MK712 touchscreen | |
122 | controller chip in your system. | |
123 | ||
124 | If unsure, say N. | |
125 | ||
126 | To compile this driver as a module, choose M here: the | |
127 | module will be called mk712. | |
128 | ||
129 | config TOUCHSCREEN_HP600 | |
4ff891eb | 130 | tristate "HP Jornada 6xx touchscreen" |
0025835c | 131 | depends on SH_HP6XX && SH_ADC |
1da177e4 | 132 | help |
4ff891eb | 133 | Say Y here if you have a HP Jornada 620/660/680/690 and want to |
1da177e4 LT |
134 | support the built-in touchscreen. |
135 | ||
1da177e4 LT |
136 | To compile this driver as a module, choose M here: the |
137 | module will be called hp680_ts_input. | |
138 | ||
5637f02a | 139 | config TOUCHSCREEN_HP7XX |
4ff891eb | 140 | tristate "HP Jornada 7xx touchscreen" |
5637f02a KE |
141 | depends on SA1100_JORNADA720_SSP |
142 | help | |
143 | Say Y here if you have a HP Jornada 710/720/728 and want | |
144 | to support the built-in touchscreen. | |
145 | ||
146 | To compile this driver as a module, choose M here: the | |
147 | module will be called jornada720_ts. | |
148 | ||
5a18c343 POF |
149 | config TOUCHSCREEN_HTCPEN |
150 | tristate "HTC Shift X9500 touchscreen" | |
151 | depends on ISA | |
152 | help | |
153 | Say Y here if you have an HTC Shift UMPC also known as HTC X9500 | |
154 | Clio / Shangrila and want to support the built-in touchscreen. | |
155 | ||
156 | If unsure, say N. | |
157 | ||
158 | To compile this driver as a module, choose M here: the | |
159 | module will be called htcpen. | |
160 | ||
ee479999 RK |
161 | config TOUCHSCREEN_PENMOUNT |
162 | tristate "Penmount serial touchscreen" | |
163 | select SERIO | |
164 | help | |
165 | Say Y here if you have a Penmount serial touchscreen connected to | |
166 | your system. | |
167 | ||
168 | If unsure, say N. | |
169 | ||
170 | To compile this driver as a module, choose M here: the | |
171 | module will be called penmount. | |
172 | ||
885c316d MD |
173 | config TOUCHSCREEN_MIGOR |
174 | tristate "Renesas MIGO-R touchscreen" | |
175 | depends on SH_MIGOR && I2C | |
176 | help | |
177 | Say Y here to enable MIGO-R touchscreen support. | |
178 | ||
179 | If unsure, say N. | |
180 | ||
181 | To compile this driver as a module, choose M here: the | |
182 | module will be called migor_ts. | |
183 | ||
4003dff4 RK |
184 | config TOUCHSCREEN_TOUCHRIGHT |
185 | tristate "Touchright serial touchscreen" | |
186 | select SERIO | |
187 | help | |
188 | Say Y here if you have a Touchright serial touchscreen connected to | |
189 | your system. | |
190 | ||
191 | If unsure, say N. | |
192 | ||
193 | To compile this driver as a module, choose M here: the | |
194 | module will be called touchright. | |
195 | ||
11ea3173 RK |
196 | config TOUCHSCREEN_TOUCHWIN |
197 | tristate "Touchwin serial touchscreen" | |
198 | select SERIO | |
199 | help | |
200 | Say Y here if you have a Touchwin serial touchscreen connected to | |
201 | your system. | |
202 | ||
203 | If unsure, say N. | |
204 | ||
205 | To compile this driver as a module, choose M here: the | |
206 | module will be called touchwin. | |
207 | ||
72d18a7b DL |
208 | config TOUCHSCREEN_ATMEL_TSADCC |
209 | tristate "Atmel Touchscreen Interface" | |
210 | depends on ARCH_AT91SAM9RL | |
211 | help | |
212 | Say Y here if you have a 4-wire touchscreen connected to the | |
213 | ADC Controller on your Atmel SoC (such as the AT91SAM9RL). | |
214 | ||
215 | If unsure, say N. | |
216 | ||
217 | To compile this driver as a module, choose M here: the | |
218 | module will be called atmel_tsadcc. | |
219 | ||
f40219bf NP |
220 | config TOUCHSCREEN_UCB1400 |
221 | tristate "Philips UCB1400 touchscreen" | |
e1036502 | 222 | select AC97_BUS |
f40219bf NP |
223 | help |
224 | This enables support for the Philips UCB1400 touchscreen interface. | |
225 | The UCB1400 is an AC97 audio codec. The touchscreen interface | |
226 | will be initialized only after the ALSA subsystem has been | |
227 | brought up and the UCB1400 detected. You therefore have to | |
228 | configure ALSA support as well (either built-in or modular, | |
229 | independently of whether this driver is itself built-in or | |
230 | modular) for this driver to work. | |
231 | ||
232 | To compile this driver as a module, choose M here: the | |
233 | module will be called ucb1400_ts. | |
234 | ||
febf1dff MB |
235 | config TOUCHSCREEN_WM97XX |
236 | tristate "Support for WM97xx AC97 touchscreen controllers" | |
237 | depends on AC97_BUS | |
238 | help | |
239 | Say Y here if you have a Wolfson Microelectronics WM97xx | |
240 | touchscreen connected to your system. Note that this option | |
241 | only enables core driver, you will also need to select | |
242 | support for appropriate chip below. | |
243 | ||
244 | If unsure, say N. | |
245 | ||
246 | To compile this driver as a module, choose M here: the | |
247 | module will be called wm97xx-ts. | |
248 | ||
9448cefc MB |
249 | config TOUCHSCREEN_WM9705 |
250 | bool "WM9705 Touchscreen interface support" | |
251 | depends on TOUCHSCREEN_WM97XX | |
252 | help | |
253 | Say Y here if you have a Wolfson Microelectronics WM9705 | |
254 | touchscreen controller connected to your system. | |
255 | ||
256 | If unsure, say N. | |
257 | ||
de22b9ef MB |
258 | config TOUCHSCREEN_WM9712 |
259 | bool "WM9712 Touchscreen interface support" | |
260 | depends on TOUCHSCREEN_WM97XX | |
261 | help | |
262 | Say Y here if you have a Wolfson Microelectronics WM9712 | |
263 | touchscreen controller connected to your system. | |
264 | ||
265 | If unsure, say N. | |
266 | ||
dca98e91 MB |
267 | config TOUCHSCREEN_WM9713 |
268 | bool "WM9713 Touchscreen interface support" | |
269 | depends on TOUCHSCREEN_WM97XX | |
270 | help | |
271 | Say Y here if you have a Wolfson Microelectronics WM9713 touchscreen | |
272 | controller connected to your system. | |
273 | ||
274 | If unsure, say N. | |
275 | ||
4db8a5f2 MB |
276 | config TOUCHSCREEN_WM97XX_MAINSTONE |
277 | tristate "WM97xx Mainstone accelerated touch" | |
278 | depends on TOUCHSCREEN_WM97XX && ARCH_PXA | |
279 | help | |
280 | Say Y here for support for streaming mode with WM97xx touchscreens | |
281 | on Mainstone systems. | |
282 | ||
283 | If unsure, say N. | |
284 | ||
285 | To compile this driver as a module, choose M here: the | |
286 | module will be called mainstone-wm97xx. | |
287 | ||
d05e84e6 DT |
288 | config TOUCHSCREEN_USB_COMPOSITE |
289 | tristate "USB Touchscreen Driver" | |
7a86edef | 290 | depends on USB_ARCH_HAS_HCD |
d05e84e6 DT |
291 | select USB |
292 | help | |
293 | USB Touchscreen driver for: | |
294 | - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700) | |
295 | - PanJit TouchSet USB | |
296 | - 3M MicroTouch USB (EX II series) | |
297 | - ITM | |
298 | - some other eTurboTouch | |
299 | - Gunze AHL61 | |
300 | - DMC TSC-10/25 | |
df561fcd | 301 | - IRTOUCHSYSTEMS/UNITOP |
a14a8401 | 302 | - IdealTEK URTC1000 |
14e40206 | 303 | - GoTop Super_Q2/GogoPen/PenPower tablets |
d05e84e6 DT |
304 | |
305 | Have a look at <http://linux.chapter7.ch/touchkit/> for | |
306 | a usage description and the required user-space stuff. | |
307 | ||
308 | To compile this driver as a module, choose M here: the | |
309 | module will be called usbtouchscreen. | |
310 | ||
311 | config TOUCHSCREEN_USB_EGALAX | |
312 | default y | |
313 | bool "eGalax, eTurboTouch CT-410/510/700 device support" if EMBEDDED | |
314 | depends on TOUCHSCREEN_USB_COMPOSITE | |
315 | ||
316 | config TOUCHSCREEN_USB_PANJIT | |
317 | default y | |
318 | bool "PanJit device support" if EMBEDDED | |
319 | depends on TOUCHSCREEN_USB_COMPOSITE | |
320 | ||
321 | config TOUCHSCREEN_USB_3M | |
322 | default y | |
323 | bool "3M/Microtouch EX II series device support" if EMBEDDED | |
324 | depends on TOUCHSCREEN_USB_COMPOSITE | |
325 | ||
326 | config TOUCHSCREEN_USB_ITM | |
327 | default y | |
328 | bool "ITM device support" if EMBEDDED | |
329 | depends on TOUCHSCREEN_USB_COMPOSITE | |
330 | ||
331 | config TOUCHSCREEN_USB_ETURBO | |
332 | default y | |
333 | bool "eTurboTouch (non-eGalax compatible) device support" if EMBEDDED | |
334 | depends on TOUCHSCREEN_USB_COMPOSITE | |
335 | ||
336 | config TOUCHSCREEN_USB_GUNZE | |
337 | default y | |
338 | bool "Gunze AHL61 device support" if EMBEDDED | |
339 | depends on TOUCHSCREEN_USB_COMPOSITE | |
340 | ||
341 | config TOUCHSCREEN_USB_DMC_TSC10 | |
342 | default y | |
343 | bool "DMC TSC-10/25 device support" if EMBEDDED | |
344 | depends on TOUCHSCREEN_USB_COMPOSITE | |
345 | ||
df561fcd OZ |
346 | config TOUCHSCREEN_USB_IRTOUCH |
347 | default y | |
348 | bool "IRTOUCHSYSTEMS/UNITOP device support" if EMBEDDED | |
349 | depends on TOUCHSCREEN_USB_COMPOSITE | |
350 | ||
a14a8401 OZ |
351 | config TOUCHSCREEN_USB_IDEALTEK |
352 | default y | |
353 | bool "IdealTEK URTC1000 device support" if EMBEDDED | |
354 | depends on TOUCHSCREEN_USB_COMPOSITE | |
355 | ||
9d5657db IF |
356 | config TOUCHSCREEN_USB_GENERAL_TOUCH |
357 | default y | |
358 | bool "GeneralTouch Touchscreen device support" if EMBEDDED | |
359 | depends on TOUCHSCREEN_USB_COMPOSITE | |
360 | ||
14e40206 JJ |
361 | config TOUCHSCREEN_USB_GOTOP |
362 | default y | |
363 | bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EMBEDDED | |
364 | depends on TOUCHSCREEN_USB_COMPOSITE | |
365 | ||
73422392 CN |
366 | config TOUCHSCREEN_TOUCHIT213 |
367 | tristate "Sahara TouchIT-213 touchscreen" | |
368 | select SERIO | |
369 | help | |
370 | Say Y here if you have a Sahara TouchIT-213 Tablet PC. | |
371 | ||
372 | If unsure, say N. | |
373 | ||
374 | To compile this driver as a module, choose M here: the | |
375 | module will be called touchit213. | |
376 | ||
1da177e4 | 377 | endif |