Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | |
2 | # | |
3 | # Network device configuration | |
4 | # | |
5 | ||
d1c0a65f | 6 | menuconfig NETDEVICES |
ce2d2aed | 7 | default y if UML |
e0009820 | 8 | depends on NET |
1da177e4 LT |
9 | bool "Network device support" |
10 | ---help--- | |
11 | You can say N here if you don't intend to connect your Linux box to | |
12 | any other computer at all. | |
13 | ||
14 | You'll have to say Y if your computer contains a network card that | |
15 | you want to use under Linux. If you are going to run SLIP or PPP over | |
16 | telephone line or null modem cable you need say Y here. Connecting | |
17 | two machines with parallel ports using PLIP needs this, as well as | |
18 | AX.25/KISS for sending Internet traffic over amateur radio links. | |
19 | ||
20 | See also "The Linux Network Administrator's Guide" by Olaf Kirch and | |
21 | Terry Dawson. Available at <http://www.tldp.org/guides.html>. | |
22 | ||
23 | If unsure, say Y. | |
24 | ||
1618cb0c RD |
25 | # All the following symbols are dependent on NETDEVICES - do not repeat |
26 | # that for each of the symbols. | |
27 | if NETDEVICES | |
cbcd2a4c | 28 | |
253af423 JHS |
29 | config IFB |
30 | tristate "Intermediate Functional Block support" | |
31 | depends on NET_CLS_ACT | |
32 | ---help--- | |
3cb2fccc | 33 | This is an intermediate driver that allows sharing of |
253af423 JHS |
34 | resources. |
35 | To compile this driver as a module, choose M here: the module | |
36 | will be called ifb. If you want to use more than one ifb | |
37 | device at a time, you need to compile this driver as a module. | |
38 | Instead of 'ifb', the devices will then be called 'ifb0', | |
39 | 'ifb1' etc. | |
40 | Look at the iproute2 documentation directory for usage etc | |
41 | ||
1da177e4 LT |
42 | config DUMMY |
43 | tristate "Dummy net driver support" | |
1da177e4 LT |
44 | ---help--- |
45 | This is essentially a bit-bucket device (i.e. traffic you send to | |
46 | this device is consigned into oblivion) with a configurable IP | |
47 | address. It is most commonly used in order to make your currently | |
48 | inactive SLIP address seem like a real address for local programs. | |
49 | If you use SLIP or PPP, you might want to say Y here. Since this | |
50 | thing often comes in handy, the default is Y. It won't enlarge your | |
51 | kernel either. What a deal. Read about it in the Network | |
52 | Administrator's Guide, available from | |
53 | <http://www.tldp.org/docs.html#guide>. | |
54 | ||
55 | To compile this driver as a module, choose M here: the module | |
56 | will be called dummy. If you want to use more than one dummy | |
57 | device at a time, you need to compile this driver as a module. | |
58 | Instead of 'dummy', the devices will then be called 'dummy0', | |
59 | 'dummy1' etc. | |
60 | ||
61 | config BONDING | |
62 | tristate "Bonding driver support" | |
1da177e4 | 63 | depends on INET |
305d552a | 64 | depends on IPV6 || IPV6=n |
1da177e4 LT |
65 | ---help--- |
66 | Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet | |
67 | Channels together. This is called 'Etherchannel' by Cisco, | |
68 | 'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux. | |
69 | ||
70 | The driver supports multiple bonding modes to allow for both high | |
47c51431 | 71 | performance and high availability operation. |
1da177e4 LT |
72 | |
73 | Refer to <file:Documentation/networking/bonding.txt> for more | |
74 | information. | |
75 | ||
76 | To compile this driver as a module, choose M here: the module | |
77 | will be called bonding. | |
78 | ||
b863ceb7 PM |
79 | config MACVLAN |
80 | tristate "MAC-VLAN support (EXPERIMENTAL)" | |
81 | depends on EXPERIMENTAL | |
82 | ---help--- | |
83 | This allows one to create virtual interfaces that map packets to | |
84 | or from specific MAC addresses to a particular interface. | |
85 | ||
3dbf8d56 PM |
86 | Macvlan devices can be added using the "ip" command from the |
87 | iproute2 package starting with the iproute2-2.6.23 release: | |
88 | ||
89 | "ip link add link <real dev> [ address MAC ] [ NAME ] type macvlan" | |
90 | ||
b863ceb7 PM |
91 | To compile this driver as a module, choose M here: the module |
92 | will be called macvlan. | |
93 | ||
1da177e4 LT |
94 | config EQUALIZER |
95 | tristate "EQL (serial line load balancing) support" | |
1da177e4 LT |
96 | ---help--- |
97 | If you have two serial connections to some other computer (this | |
98 | usually requires two modems and two telephone lines) and you use | |
99 | SLIP (the protocol for sending Internet traffic over telephone | |
100 | lines) or PPP (a better SLIP) on them, you can make them behave like | |
101 | one double speed connection using this driver. Naturally, this has | |
102 | to be supported at the other end as well, either with a similar EQL | |
103 | Linux driver or with a Livingston Portmaster 2e. | |
104 | ||
105 | Say Y if you want this and read | |
106 | <file:Documentation/networking/eql.txt>. You may also want to read | |
107 | section 6.2 of the NET-3-HOWTO, available from | |
108 | <http://www.tldp.org/docs.html#howto>. | |
109 | ||
110 | To compile this driver as a module, choose M here: the module | |
111 | will be called eql. If unsure, say N. | |
112 | ||
113 | config TUN | |
114 | tristate "Universal TUN/TAP device driver support" | |
1da177e4 LT |
115 | select CRC32 |
116 | ---help--- | |
117 | TUN/TAP provides packet reception and transmission for user space | |
118 | programs. It can be viewed as a simple Point-to-Point or Ethernet | |
119 | device, which instead of receiving packets from a physical media, | |
120 | receives them from user space program and instead of sending packets | |
121 | via physical media writes them to the user space program. | |
122 | ||
123 | When a program opens /dev/net/tun, driver creates and registers | |
124 | corresponding net device tunX or tapX. After a program closed above | |
125 | devices, driver will automatically delete tunXX or tapXX device and | |
126 | all routes corresponding to it. | |
127 | ||
128 | Please read <file:Documentation/networking/tuntap.txt> for more | |
129 | information. | |
130 | ||
131 | To compile this driver as a module, choose M here: the module | |
132 | will be called tun. | |
133 | ||
134 | If you don't know what to use this for, you don't need it. | |
135 | ||
e314dbdc | 136 | config VETH |
6a9a0250 | 137 | tristate "Virtual ethernet pair device" |
e314dbdc | 138 | ---help--- |
6a9a0250 RR |
139 | This device is a local ethernet tunnel. Devices are created in pairs. |
140 | When one end receives the packet it appears on its pair and vice | |
141 | versa. | |
e314dbdc | 142 | |
1da177e4 LT |
143 | config NET_SB1000 |
144 | tristate "General Instruments Surfboard 1000" | |
cbcd2a4c | 145 | depends on PNP |
1da177e4 LT |
146 | ---help--- |
147 | This is a driver for the General Instrument (also known as | |
148 | NextLevel) SURFboard 1000 internal | |
149 | cable modem. This is an ISA card which is used by a number of cable | |
150 | TV companies to provide cable modem access. It's a one-way | |
151 | downstream-only cable modem, meaning that your upstream net link is | |
152 | provided by your regular phone modem. | |
153 | ||
154 | At present this driver only compiles as a module, so say M here if | |
155 | you have this card. The module will be called sb1000. Then read | |
156 | <file:Documentation/networking/README.sb1000> for information on how | |
157 | to use this module, as it needs special ppp scripts for establishing | |
158 | a connection. Further documentation and the necessary scripts can be | |
159 | found at: | |
160 | ||
161 | <http://www.jacksonville.net/~fventuri/> | |
162 | <http://home.adelphia.net/~siglercm/sb1000.html> | |
163 | <http://linuxpower.cx/~cable/> | |
164 | ||
165 | If you don't have this card, of course say N. | |
166 | ||
f65fd8fb | 167 | source "drivers/net/arcnet/Kconfig" |
1da177e4 | 168 | |
00db8189 AF |
169 | source "drivers/net/phy/Kconfig" |
170 | ||
1da177e4 LT |
171 | # |
172 | # Ethernet | |
173 | # | |
174 | ||
d1c0a65f | 175 | menuconfig NET_ETHERNET |
1da177e4 | 176 | bool "Ethernet (10 or 100Mbit)" |
d1c0a65f | 177 | depends on !UML |
1da177e4 LT |
178 | ---help--- |
179 | Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common | |
180 | type of Local Area Network (LAN) in universities and companies. | |
181 | ||
182 | Common varieties of Ethernet are: 10BASE-2 or Thinnet (10 Mbps over | |
183 | coaxial cable, linking computers in a chain), 10BASE-T or twisted | |
184 | pair (10 Mbps over twisted pair cable, linking computers to central | |
185 | hubs), 10BASE-F (10 Mbps over optical fiber links, using hubs), | |
186 | 100BASE-TX (100 Mbps over two twisted pair cables, using hubs), | |
187 | 100BASE-T4 (100 Mbps over 4 standard voice-grade twisted pair | |
188 | cables, using hubs), 100BASE-FX (100 Mbps over optical fiber links) | |
189 | [the 100BASE varieties are also known as Fast Ethernet], and Gigabit | |
190 | Ethernet (1 Gbps over optical fiber or short copper links). | |
191 | ||
192 | If your Linux machine will be connected to an Ethernet and you have | |
193 | an Ethernet network interface card (NIC) installed in your computer, | |
194 | say Y here and read the Ethernet-HOWTO, available from | |
195 | <http://www.tldp.org/docs.html#howto>. You will then also have | |
196 | to say Y to the driver for your particular NIC. | |
197 | ||
198 | Note that the answer to this question won't directly affect the | |
199 | kernel: saying N will just cause the configurator to skip all | |
200 | the questions about Ethernet network cards. If unsure, say N. | |
201 | ||
d1c0a65f JE |
202 | if NET_ETHERNET |
203 | ||
1da177e4 LT |
204 | config MII |
205 | tristate "Generic Media Independent Interface device support" | |
1da177e4 LT |
206 | help |
207 | Most ethernet controllers have MII transceiver either as an external | |
208 | or internal device. It is safe to say Y or M here even if your | |
209 | ethernet card lack MII. | |
210 | ||
89e5785f HS |
211 | config MACB |
212 | tristate "Atmel MACB support" | |
61352667 | 213 | depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91CAP9 |
6c36a707 | 214 | select PHYLIB |
89e5785f HS |
215 | help |
216 | The Atmel MACB ethernet interface is found on many AT32 and AT91 | |
217 | parts. Say Y to include support for the MACB chip. | |
218 | ||
219 | To compile this driver as a module, choose M here: the module | |
220 | will be called macb. | |
221 | ||
1da177e4 LT |
222 | source "drivers/net/arm/Kconfig" |
223 | ||
825a2ff1 BD |
224 | config AX88796 |
225 | tristate "ASIX AX88796 NE2000 clone support" | |
8687991a | 226 | depends on ARM || MIPS || SUPERH |
825a2ff1 BD |
227 | select CRC32 |
228 | select MII | |
229 | help | |
230 | AX88796 driver, using platform bus to provide | |
231 | chip detection and resources | |
232 | ||
89e536a1 MD |
233 | config AX88796_93CX6 |
234 | bool "ASIX AX88796 external 93CX6 eeprom support" | |
235 | depends on AX88796 | |
236 | select EEPROM_93CX6 | |
237 | help | |
238 | Select this if your platform comes with an external 93CX6 eeprom. | |
239 | ||
1da177e4 LT |
240 | config MACE |
241 | tristate "MACE (Power Mac ethernet) support" | |
d1c0a65f | 242 | depends on PPC_PMAC && PPC32 |
1da177e4 LT |
243 | select CRC32 |
244 | help | |
245 | Power Macintoshes and clones with Ethernet built-in on the | |
246 | motherboard will usually use a MACE (Medium Access Control for | |
247 | Ethernet) interface. Say Y to include support for the MACE chip. | |
248 | ||
249 | To compile this driver as a module, choose M here: the module | |
250 | will be called mace. | |
251 | ||
252 | config MACE_AAUI_PORT | |
253 | bool "Use AAUI port instead of TP by default" | |
254 | depends on MACE | |
255 | help | |
256 | Some Apple machines (notably the Apple Network Server) which use the | |
257 | MACE ethernet chip have an Apple AUI port (small 15-pin connector), | |
258 | instead of an 8-pin RJ45 connector for twisted-pair ethernet. Say | |
259 | Y here if you have such a machine. If unsure, say N. | |
260 | The driver will default to AAUI on ANS anyway, and if you use it as | |
261 | a module, you can provide the port_aaui=0|1 to force the driver. | |
262 | ||
263 | config BMAC | |
264 | tristate "BMAC (G3 ethernet) support" | |
d1c0a65f | 265 | depends on PPC_PMAC && PPC32 |
1da177e4 LT |
266 | select CRC32 |
267 | help | |
268 | Say Y for support of BMAC Ethernet interfaces. These are used on G3 | |
269 | computers. | |
270 | ||
271 | To compile this driver as a module, choose M here: the module | |
272 | will be called bmac. | |
273 | ||
1da177e4 LT |
274 | config ARIADNE |
275 | tristate "Ariadne support" | |
d1c0a65f | 276 | depends on ZORRO |
1da177e4 LT |
277 | help |
278 | If you have a Village Tronic Ariadne Ethernet adapter, say Y. | |
279 | Otherwise, say N. | |
280 | ||
281 | To compile this driver as a module, choose M here: the module | |
282 | will be called ariadne. | |
283 | ||
284 | config A2065 | |
285 | tristate "A2065 support" | |
d1c0a65f | 286 | depends on ZORRO |
1da177e4 LT |
287 | select CRC32 |
288 | help | |
289 | If you have a Commodore A2065 Ethernet adapter, say Y. Otherwise, | |
290 | say N. | |
291 | ||
292 | To compile this driver as a module, choose M here: the module | |
293 | will be called a2065. | |
294 | ||
295 | config HYDRA | |
296 | tristate "Hydra support" | |
d1c0a65f | 297 | depends on ZORRO |
1da177e4 LT |
298 | select CRC32 |
299 | help | |
300 | If you have a Hydra Ethernet adapter, say Y. Otherwise, say N. | |
301 | ||
302 | To compile this driver as a module, choose M here: the module | |
303 | will be called hydra. | |
304 | ||
305 | config ZORRO8390 | |
306 | tristate "Zorro NS8390-based Ethernet support" | |
d1c0a65f | 307 | depends on ZORRO |
1da177e4 LT |
308 | select CRC32 |
309 | help | |
310 | This driver is for Zorro Ethernet cards using an NS8390-compatible | |
311 | chipset, like the Village Tronic Ariadne II and the Individual | |
312 | Computers X-Surf Ethernet cards. If you have such a card, say Y. | |
313 | Otherwise, say N. | |
314 | ||
315 | To compile this driver as a module, choose M here: the module | |
316 | will be called zorro8390. | |
317 | ||
318 | config APNE | |
319 | tristate "PCMCIA NE2000 support" | |
d1c0a65f | 320 | depends on AMIGA_PCMCIA |
1da177e4 LT |
321 | select CRC32 |
322 | help | |
323 | If you have a PCMCIA NE2000 compatible adapter, say Y. Otherwise, | |
324 | say N. | |
325 | ||
326 | To compile this driver as a module, choose M here: the module | |
327 | will be called apne. | |
328 | ||
1da177e4 LT |
329 | config MAC8390 |
330 | bool "Macintosh NS 8390 based ethernet cards" | |
d1c0a65f | 331 | depends on MAC |
1da177e4 LT |
332 | select CRC32 |
333 | help | |
334 | If you want to include a driver to support Nubus or LC-PDS | |
335 | Ethernet cards using an NS8390 chipset or its equivalent, say Y | |
336 | and read the Ethernet-HOWTO, available from | |
337 | <http://www.tldp.org/docs.html#howto>. | |
338 | ||
339 | config MAC89x0 | |
340 | tristate "Macintosh CS89x0 based ethernet cards" | |
d1c0a65f | 341 | depends on MAC |
1da177e4 LT |
342 | ---help--- |
343 | Support for CS89x0 chipset based Ethernet cards. If you have a | |
344 | Nubus or LC-PDS network (Ethernet) card of this type, say Y and | |
345 | read the Ethernet-HOWTO, available from | |
346 | <http://www.tldp.org/docs.html#howto>. | |
347 | ||
57ce45dd | 348 | To compile this driver as a module, choose M here. This module will |
1da177e4 LT |
349 | be called mac89x0. |
350 | ||
351 | config MACSONIC | |
352 | tristate "Macintosh SONIC based ethernet (onboard, NuBus, LC, CS)" | |
d1c0a65f | 353 | depends on MAC |
1da177e4 LT |
354 | ---help--- |
355 | Support for NatSemi SONIC based Ethernet devices. This includes | |
356 | the onboard Ethernet in many Quadras as well as some LC-PDS, | |
357 | a few Nubus and all known Comm Slot Ethernet cards. If you have | |
358 | one of these say Y and read the Ethernet-HOWTO, available from | |
359 | <http://www.tldp.org/docs.html#howto>. | |
360 | ||
57ce45dd | 361 | To compile this driver as a module, choose M here. This module will |
1da177e4 LT |
362 | be called macsonic. |
363 | ||
364 | config MACMACE | |
8b6aaab8 | 365 | bool "Macintosh (AV) onboard MACE ethernet" |
d1c0a65f | 366 | depends on MAC |
1da177e4 LT |
367 | select CRC32 |
368 | help | |
369 | Support for the onboard AMD 79C940 MACE Ethernet controller used in | |
370 | the 660AV and 840AV Macintosh. If you have one of these Macintoshes | |
371 | say Y and read the Ethernet-HOWTO, available from | |
372 | <http://www.tldp.org/docs.html#howto>. | |
373 | ||
374 | config MVME147_NET | |
375 | tristate "MVME147 (Lance) Ethernet support" | |
d1c0a65f | 376 | depends on MVME147 |
1da177e4 LT |
377 | select CRC32 |
378 | help | |
379 | Support for the on-board Ethernet interface on the Motorola MVME147 | |
380 | single-board computer. Say Y here to include the | |
381 | driver for this chip in your kernel. | |
382 | To compile this driver as a module, choose M here. | |
383 | ||
384 | config MVME16x_NET | |
385 | tristate "MVME16x Ethernet support" | |
d1c0a65f | 386 | depends on MVME16x |
1da177e4 LT |
387 | help |
388 | This is the driver for the Ethernet interface on the Motorola | |
389 | MVME162, 166, 167, 172 and 177 boards. Say Y here to include the | |
390 | driver for this chip in your kernel. | |
391 | To compile this driver as a module, choose M here. | |
392 | ||
393 | config BVME6000_NET | |
394 | tristate "BVME6000 Ethernet support" | |
d1c0a65f | 395 | depends on BVME6000 |
1da177e4 LT |
396 | help |
397 | This is the driver for the Ethernet interface on BVME4000 and | |
398 | BVME6000 VME boards. Say Y here to include the driver for this chip | |
399 | in your kernel. | |
400 | To compile this driver as a module, choose M here. | |
401 | ||
402 | config ATARILANCE | |
403 | tristate "Atari Lance support" | |
d1c0a65f | 404 | depends on ATARI |
1da177e4 LT |
405 | help |
406 | Say Y to include support for several Atari Ethernet adapters based | |
407 | on the AMD Lance chipset: RieblCard (with or without battery), or | |
408 | PAMCard VME (also the version by Rhotron, with different addresses). | |
409 | ||
1da177e4 LT |
410 | config SUN3LANCE |
411 | tristate "Sun3/Sun3x on-board LANCE support" | |
d1c0a65f | 412 | depends on SUN3 || SUN3X |
1da177e4 LT |
413 | help |
414 | Most Sun3 and Sun3x motherboards (including the 3/50, 3/60 and 3/80) | |
415 | featured an AMD Lance 10Mbit Ethernet controller on board; say Y | |
416 | here to compile in the Linux driver for this and enable Ethernet. | |
417 | General Linux information on the Sun 3 and 3x series (now | |
418 | discontinued) is at | |
419 | <http://www.angelfire.com/ca2/tech68k/sun3.html>. | |
420 | ||
421 | If you're not building a kernel for a Sun 3, say N. | |
422 | ||
423 | config SUN3_82586 | |
9a482206 | 424 | bool "Sun3 on-board Intel 82586 support" |
d1c0a65f | 425 | depends on SUN3 |
1da177e4 LT |
426 | help |
427 | This driver enables support for the on-board Intel 82586 based | |
428 | Ethernet adapter found on Sun 3/1xx and 3/2xx motherboards. Note | |
429 | that this driver does not support 82586-based adapters on additional | |
430 | VME boards. | |
431 | ||
432 | config HPLANCE | |
433 | bool "HP on-board LANCE support" | |
d1c0a65f | 434 | depends on DIO |
1da177e4 LT |
435 | select CRC32 |
436 | help | |
437 | If you want to use the builtin "LANCE" Ethernet controller on an | |
438 | HP300 machine, say Y here. | |
439 | ||
440 | config LASI_82596 | |
441 | tristate "Lasi ethernet" | |
d1c0a65f | 442 | depends on GSC |
1da177e4 | 443 | help |
6de187ee MW |
444 | Say Y here to support the builtin Intel 82596 ethernet controller |
445 | found in Hewlett-Packard PA-RISC machines with 10Mbit ethernet. | |
1da177e4 | 446 | |
f2ec8030 TB |
447 | config SNI_82596 |
448 | tristate "SNI RM ethernet" | |
449 | depends on NET_ETHERNET && SNI_RM | |
450 | help | |
451 | Say Y here to support the on-board Intel 82596 ethernet controller | |
452 | built into SNI RM machines. | |
453 | ||
ef11291b FF |
454 | config KORINA |
455 | tristate "Korina (IDT RC32434) Ethernet support" | |
f57b2061 | 456 | depends on NET_ETHERNET && MIKROTIK_RB532 |
ef11291b FF |
457 | help |
458 | If you have a Mikrotik RouterBoard 500 or IDT RC32434 | |
459 | based system say Y. Otherwise say N. | |
460 | ||
1da177e4 LT |
461 | config MIPS_JAZZ_SONIC |
462 | tristate "MIPS JAZZ onboard SONIC Ethernet support" | |
d1c0a65f | 463 | depends on MACH_JAZZ |
1da177e4 LT |
464 | help |
465 | This is the driver for the onboard card of MIPS Magnum 4000, | |
466 | Acer PICA, Olivetti M700-10 and a few other identical OEM systems. | |
467 | ||
74f2a5f0 CZ |
468 | config XTENSA_XT2000_SONIC |
469 | tristate "Xtensa XT2000 onboard SONIC Ethernet support" | |
470 | depends on XTENSA_PLATFORM_XT2000 | |
471 | help | |
472 | This is the driver for the onboard card of the Xtensa XT2000 board. | |
473 | ||
1da177e4 LT |
474 | config MIPS_AU1X00_ENET |
475 | bool "MIPS AU1000 Ethernet support" | |
d1c0a65f | 476 | depends on SOC_AU1X00 |
0638dec0 | 477 | select PHYLIB |
1da177e4 LT |
478 | select CRC32 |
479 | help | |
480 | If you have an Alchemy Semi AU1X00 based system | |
481 | say Y. Otherwise, say N. | |
482 | ||
1da177e4 LT |
483 | config SGI_IOC3_ETH |
484 | bool "SGI IOC3 Ethernet" | |
d1c0a65f | 485 | depends on PCI && SGI_IP27 |
1da177e4 LT |
486 | select CRC32 |
487 | select MII | |
488 | help | |
489 | If you have a network (Ethernet) card of this type, say Y and read | |
490 | the Ethernet-HOWTO, available from | |
491 | <http://www.tldp.org/docs.html#howto>. | |
492 | ||
dcbf8477 | 493 | config MIPS_SIM_NET |
1e2b980f | 494 | tristate "MIPS simulator Network device" |
d1c0a65f | 495 | depends on MIPS_SIM |
dcbf8477 RB |
496 | help |
497 | The MIPSNET device is a simple Ethernet network device which is | |
498 | emulated by the MIPS Simulator. | |
499 | If you are not using a MIPSsim or are unsure, say N. | |
500 | ||
1da177e4 LT |
501 | config SGI_O2MACE_ETH |
502 | tristate "SGI O2 MACE Fast Ethernet support" | |
d1c0a65f | 503 | depends on SGI_IP32=y |
1da177e4 LT |
504 | |
505 | config STNIC | |
506 | tristate "National DP83902AV support" | |
d1c0a65f | 507 | depends on SUPERH |
1da177e4 LT |
508 | select CRC32 |
509 | help | |
510 | Support for cards based on the National Semiconductor DP83902AV | |
511 | ST-NIC Serial Network Interface Controller for Twisted Pair. This | |
512 | is a 10Mbit/sec Ethernet controller. Product overview and specs at | |
513 | <http://www.national.com/pf/DP/DP83902A.html>. | |
514 | ||
515 | If unsure, say N. | |
516 | ||
86a74ff2 NI |
517 | config SH_ETH |
518 | tristate "Renesas SuperH Ethernet support" | |
519 | depends on SUPERH && \ | |
71557a37 YS |
520 | (CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712 || CPU_SUBTYPE_SH7763 || \ |
521 | CPU_SUBTYPE_SH7619) | |
86a74ff2 NI |
522 | select CRC32 |
523 | select MII | |
524 | select MDIO_BITBANG | |
525 | select PHYLIB | |
526 | help | |
527 | Renesas SuperH Ethernet device driver. | |
71557a37 | 528 | This driver support SH7710, SH7712, SH7763 and SH7619. |
86a74ff2 | 529 | |
1da177e4 LT |
530 | config SUNLANCE |
531 | tristate "Sun LANCE support" | |
d1c0a65f | 532 | depends on SBUS |
1da177e4 LT |
533 | select CRC32 |
534 | help | |
535 | This driver supports the "le" interface present on all 32-bit Sparc | |
536 | systems, on some older Ultra systems and as an Sbus option. These | |
537 | cards are based on the AMD Lance chipset, which is better known | |
538 | via the NE2100 cards. | |
539 | ||
540 | To compile this driver as a module, choose M here: the module | |
541 | will be called sunlance. | |
542 | ||
543 | config HAPPYMEAL | |
544 | tristate "Sun Happy Meal 10/100baseT support" | |
d1c0a65f | 545 | depends on SBUS || PCI |
1da177e4 LT |
546 | select CRC32 |
547 | help | |
548 | This driver supports the "hme" interface present on most Ultra | |
549 | systems and as an option on older Sbus systems. This driver supports | |
550 | both PCI and Sbus devices. This driver also supports the "qfe" quad | |
551 | 100baseT device available in both PCI and Sbus configurations. | |
552 | ||
553 | To compile this driver as a module, choose M here: the module | |
554 | will be called sunhme. | |
555 | ||
556 | config SUNBMAC | |
557 | tristate "Sun BigMAC 10/100baseT support (EXPERIMENTAL)" | |
d1c0a65f | 558 | depends on SBUS && EXPERIMENTAL |
1da177e4 LT |
559 | select CRC32 |
560 | help | |
561 | This driver supports the "be" interface available as an Sbus option. | |
562 | This is Sun's older 100baseT Ethernet device. | |
563 | ||
564 | To compile this driver as a module, choose M here: the module | |
565 | will be called sunbmac. | |
566 | ||
567 | config SUNQE | |
568 | tristate "Sun QuadEthernet support" | |
d1c0a65f | 569 | depends on SBUS |
1da177e4 LT |
570 | select CRC32 |
571 | help | |
572 | This driver supports the "qe" 10baseT Ethernet device, available as | |
573 | an Sbus option. Note that this is not the same as Quad FastEthernet | |
574 | "qfe" which is supported by the Happy Meal driver instead. | |
575 | ||
576 | To compile this driver as a module, choose M here: the module | |
577 | will be called sunqe. | |
578 | ||
579 | config SUNGEM | |
580 | tristate "Sun GEM support" | |
d1c0a65f | 581 | depends on PCI |
1da177e4 LT |
582 | select CRC32 |
583 | help | |
584 | Support for the Sun GEM chip, aka Sun GigabitEthernet/P 2.0. See also | |
585 | <http://www.sun.com/products-n-solutions/hardware/docs/pdf/806-3985-10.pdf>. | |
586 | ||
1f26dac3 DM |
587 | config CASSINI |
588 | tristate "Sun Cassini support" | |
d1c0a65f | 589 | depends on PCI |
1f26dac3 DM |
590 | select CRC32 |
591 | help | |
592 | Support for the Sun Cassini chip, aka Sun GigaSwift Ethernet. See also | |
593 | <http://www.sun.com/products-n-solutions/hardware/docs/pdf/817-4341-10.pdf> | |
594 | ||
4c521e42 DM |
595 | config SUNVNET |
596 | tristate "Sun Virtual Network support" | |
597 | depends on SUN_LDOMS | |
598 | help | |
599 | Support for virtual network devices under Sun Logical Domains. | |
600 | ||
1da177e4 LT |
601 | config NET_VENDOR_3COM |
602 | bool "3COM cards" | |
d1c0a65f | 603 | depends on ISA || EISA || MCA || PCI |
1da177e4 LT |
604 | help |
605 | If you have a network (Ethernet) card belonging to this class, say Y | |
606 | and read the Ethernet-HOWTO, available from | |
607 | <http://www.tldp.org/docs.html#howto>. | |
608 | ||
609 | Note that the answer to this question doesn't directly affect the | |
610 | kernel: saying N will just cause the configurator to skip all | |
611 | the questions about 3COM cards. If you say Y, you will be asked for | |
612 | your specific card in the following questions. | |
613 | ||
614 | config EL1 | |
615 | tristate "3c501 \"EtherLink\" support" | |
616 | depends on NET_VENDOR_3COM && ISA | |
617 | ---help--- | |
618 | If you have a network (Ethernet) card of this type, say Y and read | |
619 | the Ethernet-HOWTO, available from | |
620 | <http://www.tldp.org/docs.html#howto>. Also, consider buying a | |
621 | new card, since the 3c501 is slow, broken, and obsolete: you will | |
622 | have problems. Some people suggest to ping ("man ping") a nearby | |
623 | machine every minute ("man cron") when using this card. | |
624 | ||
57ce45dd | 625 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
626 | will be called 3c501. |
627 | ||
628 | config EL2 | |
629 | tristate "3c503 \"EtherLink II\" support" | |
630 | depends on NET_VENDOR_3COM && ISA | |
631 | select CRC32 | |
632 | help | |
633 | If you have a network (Ethernet) card of this type, say Y and read | |
634 | the Ethernet-HOWTO, available from | |
635 | <http://www.tldp.org/docs.html#howto>. | |
636 | ||
57ce45dd | 637 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
638 | will be called 3c503. |
639 | ||
640 | config ELPLUS | |
641 | tristate "3c505 \"EtherLink Plus\" support" | |
a5532606 | 642 | depends on NET_VENDOR_3COM && ISA && ISA_DMA_API |
1da177e4 LT |
643 | ---help--- |
644 | Information about this network (Ethernet) card can be found in | |
645 | <file:Documentation/networking/3c505.txt>. If you have a card of | |
646 | this type, say Y and read the Ethernet-HOWTO, available from | |
647 | <http://www.tldp.org/docs.html#howto>. | |
648 | ||
57ce45dd | 649 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
650 | will be called 3c505. |
651 | ||
652 | config EL16 | |
653 | tristate "3c507 \"EtherLink 16\" support (EXPERIMENTAL)" | |
654 | depends on NET_VENDOR_3COM && ISA && EXPERIMENTAL | |
655 | help | |
656 | If you have a network (Ethernet) card of this type, say Y and read | |
657 | the Ethernet-HOWTO, available from | |
658 | <http://www.tldp.org/docs.html#howto>. | |
659 | ||
57ce45dd | 660 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
661 | will be called 3c507. |
662 | ||
663 | config EL3 | |
664 | tristate "3c509/3c529 (MCA)/3c579 \"EtherLink III\" support" | |
665 | depends on NET_VENDOR_3COM && (ISA || EISA || MCA) | |
666 | ---help--- | |
667 | If you have a network (Ethernet) card belonging to the 3Com | |
668 | EtherLinkIII series, say Y and read the Ethernet-HOWTO, available | |
669 | from <http://www.tldp.org/docs.html#howto>. | |
670 | ||
671 | If your card is not working you may need to use the DOS | |
672 | setup disk to disable Plug & Play mode, and to select the default | |
673 | media type. | |
674 | ||
57ce45dd | 675 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
676 | will be called 3c509. |
677 | ||
678 | config 3C515 | |
679 | tristate "3c515 ISA \"Fast EtherLink\"" | |
a5532606 | 680 | depends on NET_VENDOR_3COM && (ISA || EISA) && ISA_DMA_API |
1da177e4 LT |
681 | help |
682 | If you have a 3Com ISA EtherLink XL "Corkscrew" 3c515 Fast Ethernet | |
683 | network card, say Y and read the Ethernet-HOWTO, available from | |
684 | <http://www.tldp.org/docs.html#howto>. | |
685 | ||
57ce45dd | 686 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
687 | will be called 3c515. |
688 | ||
689 | config ELMC | |
690 | tristate "3c523 \"EtherLink/MC\" support" | |
691 | depends on NET_VENDOR_3COM && MCA_LEGACY | |
692 | help | |
693 | If you have a network (Ethernet) card of this type, say Y and read | |
694 | the Ethernet-HOWTO, available from | |
695 | <http://www.tldp.org/docs.html#howto>. | |
696 | ||
57ce45dd | 697 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
698 | will be called 3c523. |
699 | ||
700 | config ELMC_II | |
701 | tristate "3c527 \"EtherLink/MC 32\" support (EXPERIMENTAL)" | |
702 | depends on NET_VENDOR_3COM && MCA && MCA_LEGACY | |
703 | help | |
704 | If you have a network (Ethernet) card of this type, say Y and read | |
705 | the Ethernet-HOWTO, available from | |
706 | <http://www.tldp.org/docs.html#howto>. | |
707 | ||
57ce45dd | 708 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
709 | will be called 3c527. |
710 | ||
711 | config VORTEX | |
712 | tristate "3c590/3c900 series (592/595/597) \"Vortex/Boomerang\" support" | |
713 | depends on NET_VENDOR_3COM && (PCI || EISA) | |
714 | select MII | |
715 | ---help--- | |
47c51431 JM |
716 | This option enables driver support for a large number of 10Mbps and |
717 | 10/100Mbps EISA, PCI and PCMCIA 3Com network cards: | |
1da177e4 LT |
718 | |
719 | "Vortex" (Fast EtherLink 3c590/3c592/3c595/3c597) EISA and PCI | |
720 | "Boomerang" (EtherLink XL 3c900 or 3c905) PCI | |
721 | "Cyclone" (3c540/3c900/3c905/3c980/3c575/3c656) PCI and Cardbus | |
722 | "Tornado" (3c905) PCI | |
723 | "Hurricane" (3c555/3cSOHO) PCI | |
724 | ||
725 | If you have such a card, say Y and read the Ethernet-HOWTO, | |
726 | available from <http://www.tldp.org/docs.html#howto>. More | |
727 | specific information is in | |
728 | <file:Documentation/networking/vortex.txt> and in the comments at | |
729 | the beginning of <file:drivers/net/3c59x.c>. | |
730 | ||
57ce45dd | 731 | To compile this support as a module, choose M here. |
1da177e4 LT |
732 | |
733 | config TYPHOON | |
734 | tristate "3cr990 series \"Typhoon\" support" | |
735 | depends on NET_VENDOR_3COM && PCI | |
736 | select CRC32 | |
737 | ---help--- | |
738 | This option enables driver support for the 3cr990 series of cards: | |
739 | ||
740 | 3C990-TX, 3CR990-TX-95, 3CR990-TX-97, 3CR990-FX-95, 3CR990-FX-97, | |
741 | 3CR990SVR, 3CR990SVR95, 3CR990SVR97, 3CR990-FX-95 Server, | |
742 | 3CR990-FX-97 Server, 3C990B-TX-M, 3C990BSVR | |
743 | ||
744 | If you have a network (Ethernet) card of this type, say Y and read | |
745 | the Ethernet-HOWTO, available from | |
746 | <http://www.tldp.org/docs.html#howto>. | |
747 | ||
57ce45dd | 748 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
749 | will be called typhoon. |
750 | ||
751 | config LANCE | |
752 | tristate "AMD LANCE and PCnet (AT1500 and NE2100) support" | |
d1c0a65f | 753 | depends on ISA && ISA_DMA_API |
1da177e4 LT |
754 | help |
755 | If you have a network (Ethernet) card of this type, say Y and read | |
756 | the Ethernet-HOWTO, available from | |
757 | <http://www.tldp.org/docs.html#howto>. Some LinkSys cards are | |
758 | of this type. | |
759 | ||
760 | To compile this driver as a module, choose M here: the module | |
761 | will be called lance. This is recommended. | |
762 | ||
763 | config NET_VENDOR_SMC | |
764 | bool "Western Digital/SMC cards" | |
d1c0a65f | 765 | depends on ISA || MCA || EISA || MAC |
1da177e4 LT |
766 | help |
767 | If you have a network (Ethernet) card belonging to this class, say Y | |
768 | and read the Ethernet-HOWTO, available from | |
769 | <http://www.tldp.org/docs.html#howto>. | |
770 | ||
771 | Note that the answer to this question doesn't directly affect the | |
772 | kernel: saying N will just cause the configurator to skip all | |
773 | the questions about Western Digital cards. If you say Y, you will be | |
774 | asked for your specific card in the following questions. | |
775 | ||
776 | config WD80x3 | |
777 | tristate "WD80*3 support" | |
778 | depends on NET_VENDOR_SMC && ISA | |
779 | select CRC32 | |
780 | help | |
781 | If you have a network (Ethernet) card of this type, say Y and read | |
782 | the Ethernet-HOWTO, available from | |
783 | <http://www.tldp.org/docs.html#howto>. | |
784 | ||
57ce45dd | 785 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
786 | will be called wd. |
787 | ||
788 | config ULTRAMCA | |
789 | tristate "SMC Ultra MCA support" | |
790 | depends on NET_VENDOR_SMC && MCA | |
791 | select CRC32 | |
792 | help | |
793 | If you have a network (Ethernet) card of this type and are running | |
794 | an MCA based system (PS/2), say Y and read the Ethernet-HOWTO, | |
795 | available from <http://www.tldp.org/docs.html#howto>. | |
796 | ||
57ce45dd | 797 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
798 | will be called smc-mca. |
799 | ||
800 | config ULTRA | |
801 | tristate "SMC Ultra support" | |
802 | depends on NET_VENDOR_SMC && ISA | |
803 | select CRC32 | |
804 | ---help--- | |
805 | If you have a network (Ethernet) card of this type, say Y and read | |
806 | the Ethernet-HOWTO, available from | |
807 | <http://www.tldp.org/docs.html#howto>. | |
808 | ||
809 | Important: There have been many reports that, with some motherboards | |
810 | mixing an SMC Ultra and an Adaptec AHA154x SCSI card (or compatible, | |
811 | such as some BusLogic models) causes corruption problems with many | |
812 | operating systems. The Linux smc-ultra driver has a work-around for | |
813 | this but keep it in mind if you have such a SCSI card and have | |
814 | problems. | |
815 | ||
57ce45dd | 816 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
817 | will be called smc-ultra. |
818 | ||
819 | config ULTRA32 | |
820 | tristate "SMC Ultra32 EISA support" | |
821 | depends on NET_VENDOR_SMC && EISA | |
822 | select CRC32 | |
823 | help | |
824 | If you have a network (Ethernet) card of this type, say Y and read | |
825 | the Ethernet-HOWTO, available from | |
826 | <http://www.tldp.org/docs.html#howto>. | |
827 | ||
57ce45dd | 828 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
829 | will be called smc-ultra32. |
830 | ||
e190d6b1 | 831 | config BFIN_MAC |
736783b8 | 832 | tristate "Blackfin on-chip MAC support" |
33a2a2b4 | 833 | depends on NET_ETHERNET && (BF516 || BF518 || BF526 || BF527 || BF536 || BF537) |
e190d6b1 | 834 | select CRC32 |
eeb70af9 BW |
835 | select MII |
836 | select PHYLIB | |
e190d6b1 BW |
837 | select BFIN_MAC_USE_L1 if DMA_UNCACHED_NONE |
838 | help | |
736783b8 | 839 | This is the driver for Blackfin on-chip mac device. Say Y if you want it |
e190d6b1 BW |
840 | compiled into the kernel. This driver is also available as a module |
841 | ( = code which can be inserted in and removed from the running kernel | |
842 | whenever you want). The module will be called bfin_mac. | |
843 | ||
844 | config BFIN_MAC_USE_L1 | |
845 | bool "Use L1 memory for rx/tx packets" | |
6893ff1c | 846 | depends on BFIN_MAC && (BF527 || BF537) |
e190d6b1 BW |
847 | default y |
848 | help | |
01dd2fbf | 849 | To get maximum network performance, you should use L1 memory as rx/tx buffers. |
e190d6b1 BW |
850 | Say N here if you want to reserve L1 memory for other uses. |
851 | ||
852 | config BFIN_TX_DESC_NUM | |
853 | int "Number of transmit buffer packets" | |
854 | depends on BFIN_MAC | |
855 | range 6 10 if BFIN_MAC_USE_L1 | |
856 | range 10 100 | |
857 | default "10" | |
858 | help | |
859 | Set the number of buffer packets used in driver. | |
860 | ||
861 | config BFIN_RX_DESC_NUM | |
862 | int "Number of receive buffer packets" | |
863 | depends on BFIN_MAC | |
864 | range 20 100 if BFIN_MAC_USE_L1 | |
865 | range 20 800 | |
866 | default "20" | |
867 | help | |
868 | Set the number of buffer packets used in driver. | |
869 | ||
870 | config BFIN_MAC_RMII | |
871 | bool "RMII PHY Interface (EXPERIMENTAL)" | |
872 | depends on BFIN_MAC && EXPERIMENTAL | |
6893ff1c MH |
873 | default y if BFIN527_EZKIT |
874 | default n if BFIN537_STAMP | |
e190d6b1 BW |
875 | help |
876 | Use Reduced PHY MII Interface | |
877 | ||
d1c0a65f JE |
878 | config SMC9194 |
879 | tristate "SMC 9194 support" | |
880 | depends on NET_VENDOR_SMC && (ISA || MAC && BROKEN) | |
881 | select CRC32 | |
882 | ---help--- | |
883 | This is support for the SMC9xxx based Ethernet cards. Choose this | |
884 | option if you have a DELL laptop with the docking station, or | |
885 | another SMC9192/9194 based chipset. Say Y if you want it compiled | |
886 | into the kernel, and read the file | |
887 | <file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO, | |
888 | available from <http://www.tldp.org/docs.html#howto>. | |
889 | ||
57ce45dd | 890 | To compile this driver as a module, choose M here. The module |
d1c0a65f JE |
891 | will be called smc9194. |
892 | ||
1da177e4 LT |
893 | config SMC91X |
894 | tristate "SMC 91C9x/91C1xxx support" | |
895 | select CRC32 | |
896 | select MII | |
b920de1b | 897 | depends on ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || \ |
cde0d910 | 898 | MIPS || BLACKFIN || MN10300 |
1da177e4 LT |
899 | help |
900 | This is a driver for SMC's 91x series of Ethernet chipsets, | |
901 | including the SMC91C94 and the SMC91C111. Say Y if you want it | |
902 | compiled into the kernel, and read the file | |
903 | <file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO, | |
904 | available from <http://www.linuxdoc.org/docs.html#howto>. | |
905 | ||
906 | This driver is also available as a module ( = code which can be | |
907 | inserted in and removed from the running kernel whenever you want). | |
908 | The module will be called smc91x. If you want to compile it as a | |
57ce45dd | 909 | module, say M here and read <file:Documentation/kbuild/modules.txt>. |
1da177e4 | 910 | |
92aa674d SH |
911 | config NET_NETX |
912 | tristate "NetX Ethernet support" | |
913 | select MII | |
d1c0a65f | 914 | depends on ARCH_NETX |
92aa674d SH |
915 | help |
916 | This is support for the Hilscher netX builtin Ethernet ports | |
917 | ||
57ce45dd | 918 | To compile this driver as a module, choose M here. The module |
92aa674d SH |
919 | will be called netx-eth. |
920 | ||
a1365275 SH |
921 | config DM9000 |
922 | tristate "DM9000 support" | |
f40d24d9 | 923 | depends on ARM || BLACKFIN || MIPS |
a1365275 SH |
924 | select CRC32 |
925 | select MII | |
926 | ---help--- | |
927 | Support for DM9000 chipset. | |
928 | ||
57ce45dd AB |
929 | To compile this driver as a module, choose M here. The module |
930 | will be called dm9000. | |
a1365275 | 931 | |
485ca22a BD |
932 | config DM9000_DEBUGLEVEL |
933 | int "DM9000 maximum debug level" | |
934 | depends on DM9000 | |
935 | default 4 | |
936 | help | |
937 | The maximum level of debugging code compiled into the DM9000 | |
938 | driver. | |
939 | ||
f8dd0ecb BD |
940 | config DM9000_FORCE_SIMPLE_PHY_POLL |
941 | bool "Force simple NSR based PHY polling" | |
942 | depends on DM9000 | |
943 | ---help--- | |
944 | This configuration forces the DM9000 to use the NSR's LinkStatus | |
945 | bit to determine if the link is up or down instead of the more | |
946 | costly MII PHY reads. Note, this will not work if the chip is | |
947 | operating with an external PHY. | |
948 | ||
3ec9c11d CL |
949 | config ENC28J60 |
950 | tristate "ENC28J60 support" | |
951 | depends on EXPERIMENTAL && SPI && NET_ETHERNET | |
952 | select CRC32 | |
953 | ---help--- | |
954 | Support for the Microchip EN28J60 ethernet chip. | |
955 | ||
2bfc79de | 956 | To compile this driver as a module, choose M here. The module will be |
3ec9c11d CL |
957 | called enc28j60. |
958 | ||
959 | config ENC28J60_WRITEVERIFY | |
960 | bool "Enable write verify" | |
961 | depends on ENC28J60 | |
962 | ---help--- | |
963 | Enable the verify after the buffer write useful for debugging purpose. | |
964 | If unsure, say N. | |
965 | ||
0a0c72c9 DM |
966 | config SMC911X |
967 | tristate "SMSC LAN911[5678] support" | |
968 | select CRC32 | |
969 | select MII | |
bd2c4972 | 970 | depends on ARM || SUPERH |
0a0c72c9 DM |
971 | help |
972 | This is a driver for SMSC's LAN911x series of Ethernet chipsets | |
973 | including the new LAN9115, LAN9116, LAN9117, and LAN9118. | |
974 | Say Y if you want it compiled into the kernel, | |
975 | and read the Ethernet-HOWTO, available from | |
976 | <http://www.linuxdoc.org/docs.html#howto>. | |
977 | ||
978 | This driver is also available as a module. The module will be | |
979 | called smc911x. If you want to compile it as a module, say M | |
39f5fb30 | 980 | here and read <file:Documentation/kbuild/modules.txt> |
0a0c72c9 | 981 | |
fd9abb3d SG |
982 | config SMSC911X |
983 | tristate "SMSC LAN911x/LAN921x families embedded ethernet support" | |
984 | depends on ARM || SUPERH | |
985 | select CRC32 | |
986 | select MII | |
987 | select PHYLIB | |
988 | ---help--- | |
989 | Say Y here if you want support for SMSC LAN911x and LAN921x families | |
990 | of ethernet controllers. | |
991 | ||
992 | To compile this driver as a module, choose M here and read | |
993 | <file:Documentation/networking/net-modules.txt>. The module | |
994 | will be called smsc911x. | |
995 | ||
1da177e4 LT |
996 | config NET_VENDOR_RACAL |
997 | bool "Racal-Interlan (Micom) NI cards" | |
d1c0a65f | 998 | depends on ISA |
1da177e4 LT |
999 | help |
1000 | If you have a network (Ethernet) card belonging to this class, such | |
1001 | as the NI5010, NI5210 or NI6210, say Y and read the Ethernet-HOWTO, | |
1002 | available from <http://www.tldp.org/docs.html#howto>. | |
1003 | ||
1004 | Note that the answer to this question doesn't directly affect the | |
1005 | kernel: saying N will just cause the configurator to skip all | |
1006 | the questions about NI cards. If you say Y, you will be asked for | |
1007 | your specific card in the following questions. | |
1008 | ||
1009 | config NI5010 | |
1010 | tristate "NI5010 support (EXPERIMENTAL)" | |
1011 | depends on NET_VENDOR_RACAL && ISA && EXPERIMENTAL && BROKEN_ON_SMP | |
1012 | ---help--- | |
1013 | If you have a network (Ethernet) card of this type, say Y and read | |
1014 | the Ethernet-HOWTO, available from | |
1015 | <http://www.tldp.org/docs.html#howto>. Note that this is still | |
1016 | experimental code. | |
1017 | ||
57ce45dd | 1018 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1019 | will be called ni5010. |
1020 | ||
1021 | config NI52 | |
1022 | tristate "NI5210 support" | |
1023 | depends on NET_VENDOR_RACAL && ISA | |
1024 | help | |
1025 | If you have a network (Ethernet) card of this type, say Y and read | |
1026 | the Ethernet-HOWTO, available from | |
1027 | <http://www.tldp.org/docs.html#howto>. | |
1028 | ||
57ce45dd | 1029 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1030 | will be called ni52. |
1031 | ||
1032 | config NI65 | |
1033 | tristate "NI6510 support" | |
a5532606 | 1034 | depends on NET_VENDOR_RACAL && ISA && ISA_DMA_API |
1da177e4 LT |
1035 | help |
1036 | If you have a network (Ethernet) card of this type, say Y and read | |
1037 | the Ethernet-HOWTO, available from | |
1038 | <http://www.tldp.org/docs.html#howto>. | |
1039 | ||
57ce45dd | 1040 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1041 | will be called ni65. |
1042 | ||
1043 | source "drivers/net/tulip/Kconfig" | |
1044 | ||
1045 | config AT1700 | |
1046 | tristate "AT1700/1720 support (EXPERIMENTAL)" | |
d1c0a65f | 1047 | depends on (ISA || MCA_LEGACY) && EXPERIMENTAL |
1da177e4 LT |
1048 | select CRC32 |
1049 | ---help--- | |
1050 | If you have a network (Ethernet) card of this type, say Y and read | |
1051 | the Ethernet-HOWTO, available from | |
1052 | <http://www.tldp.org/docs.html#howto>. | |
1053 | ||
57ce45dd | 1054 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1055 | will be called at1700. |
1056 | ||
1057 | config DEPCA | |
1058 | tristate "DEPCA, DE10x, DE200, DE201, DE202, DE422 support" | |
d1c0a65f | 1059 | depends on ISA || EISA || MCA |
1da177e4 LT |
1060 | select CRC32 |
1061 | ---help--- | |
1062 | If you have a network (Ethernet) card of this type, say Y and read | |
1063 | the Ethernet-HOWTO, available from | |
1064 | <http://www.tldp.org/docs.html#howto> as well as | |
1065 | <file:drivers/net/depca.c>. | |
1066 | ||
57ce45dd | 1067 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1068 | will be called depca. |
1069 | ||
1070 | config HP100 | |
1071 | tristate "HP 10/100VG PCLAN (ISA, EISA, PCI) support" | |
d1c0a65f | 1072 | depends on ISA || EISA || PCI |
1da177e4 LT |
1073 | help |
1074 | If you have a network (Ethernet) card of this type, say Y and read | |
1075 | the Ethernet-HOWTO, available from | |
1076 | <http://www.tldp.org/docs.html#howto>. | |
1077 | ||
57ce45dd | 1078 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1079 | will be called hp100. |
1080 | ||
1081 | config NET_ISA | |
1082 | bool "Other ISA cards" | |
d1c0a65f | 1083 | depends on ISA |
1da177e4 LT |
1084 | ---help--- |
1085 | If your network (Ethernet) card hasn't been mentioned yet and its | |
1086 | bus system (that's the way the cards talks to the other components | |
1087 | of your computer) is ISA (as opposed to EISA, VLB or PCI), say Y. | |
1088 | Make sure you know the name of your card. Read the Ethernet-HOWTO, | |
1089 | available from <http://www.tldp.org/docs.html#howto>. | |
1090 | ||
1091 | If unsure, say Y. | |
1092 | ||
1093 | Note that the answer to this question doesn't directly affect the | |
1094 | kernel: saying N will just cause the configurator to skip all | |
1095 | the remaining ISA network card questions. If you say Y, you will be | |
1096 | asked for your specific card in the following questions. | |
1097 | ||
1098 | config E2100 | |
1099 | tristate "Cabletron E21xx support" | |
1100 | depends on NET_ISA | |
1101 | select CRC32 | |
1102 | help | |
1103 | If you have a network (Ethernet) card of this type, say Y and read | |
1104 | the Ethernet-HOWTO, available from | |
1105 | <http://www.tldp.org/docs.html#howto>. | |
1106 | ||
57ce45dd | 1107 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1108 | will be called e2100. |
1109 | ||
1110 | config EWRK3 | |
1111 | tristate "EtherWORKS 3 (DE203, DE204, DE205) support" | |
1112 | depends on NET_ISA | |
1113 | select CRC32 | |
1114 | ---help--- | |
1115 | This driver supports the DE203, DE204 and DE205 network (Ethernet) | |
1116 | cards. If this is for you, say Y and read | |
1117 | <file:Documentation/networking/ewrk3.txt> in the kernel source as | |
1118 | well as the Ethernet-HOWTO, available from | |
1119 | <http://www.tldp.org/docs.html#howto>. | |
1120 | ||
57ce45dd | 1121 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1122 | will be called ewrk3. |
1123 | ||
1124 | config EEXPRESS | |
1125 | tristate "EtherExpress 16 support" | |
1126 | depends on NET_ISA | |
1127 | ---help--- | |
1128 | If you have an EtherExpress16 network (Ethernet) card, say Y and | |
1129 | read the Ethernet-HOWTO, available from | |
1130 | <http://www.tldp.org/docs.html#howto>. Note that the Intel | |
1131 | EtherExpress16 card used to be regarded as a very poor choice | |
1132 | because the driver was very unreliable. We now have a new driver | |
1133 | that should do better. | |
1134 | ||
57ce45dd | 1135 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1136 | will be called eexpress. |
1137 | ||
1138 | config EEXPRESS_PRO | |
1139 | tristate "EtherExpressPro support/EtherExpress 10 (i82595) support" | |
1140 | depends on NET_ISA | |
1141 | ---help--- | |
1142 | If you have a network (Ethernet) card of this type, say Y. This | |
47c51431 | 1143 | driver supports Intel i82595{FX,TX} based boards. Note however |
1da177e4 LT |
1144 | that the EtherExpress PRO/100 Ethernet card has its own separate |
1145 | driver. Please read the Ethernet-HOWTO, available from | |
1146 | <http://www.tldp.org/docs.html#howto>. | |
1147 | ||
57ce45dd | 1148 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1149 | will be called eepro. |
1150 | ||
1da177e4 LT |
1151 | config HPLAN_PLUS |
1152 | tristate "HP PCLAN+ (27247B and 27252A) support" | |
1153 | depends on NET_ISA | |
1154 | select CRC32 | |
1155 | help | |
1156 | If you have a network (Ethernet) card of this type, say Y and read | |
1157 | the Ethernet-HOWTO, available from | |
1158 | <http://www.tldp.org/docs.html#howto>. | |
1159 | ||
57ce45dd | 1160 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1161 | will be called hp-plus. |
1162 | ||
1163 | config HPLAN | |
1164 | tristate "HP PCLAN (27245 and other 27xxx series) support" | |
1165 | depends on NET_ISA | |
1166 | select CRC32 | |
1167 | help | |
1168 | If you have a network (Ethernet) card of this type, say Y and read | |
1169 | the Ethernet-HOWTO, available from | |
1170 | <http://www.tldp.org/docs.html#howto>. | |
1171 | ||
57ce45dd | 1172 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1173 | will be called hp. |
1174 | ||
1175 | config LP486E | |
1176 | tristate "LP486E on board Ethernet" | |
1177 | depends on NET_ISA | |
1178 | help | |
1179 | Say Y here to support the 82596-based on-board Ethernet controller | |
1180 | for the Panther motherboard, which is one of the two shipped in the | |
1181 | Intel Professional Workstation. | |
1182 | ||
1183 | config ETH16I | |
1184 | tristate "ICL EtherTeam 16i/32 support" | |
1185 | depends on NET_ISA | |
1186 | help | |
1187 | If you have a network (Ethernet) card of this type, say Y and read | |
1188 | the Ethernet-HOWTO, available from | |
1189 | <http://www.tldp.org/docs.html#howto>. | |
1190 | ||
57ce45dd | 1191 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1192 | will be called eth16i. |
1193 | ||
1194 | config NE2000 | |
1195 | tristate "NE2000/NE1000 support" | |
c7e65c17 | 1196 | depends on NET_ISA || (Q40 && m) || M32R || MACH_TX49XX |
1da177e4 LT |
1197 | select CRC32 |
1198 | ---help--- | |
1199 | If you have a network (Ethernet) card of this type, say Y and read | |
1200 | the Ethernet-HOWTO, available from | |
1201 | <http://www.tldp.org/docs.html#howto>. Many Ethernet cards | |
1202 | without a specific driver are compatible with NE2000. | |
1203 | ||
1204 | If you have a PCI NE2000 card however, say N here and Y to "PCI | |
28beaf65 JJ |
1205 | NE2000 and clone support" under "EISA, VLB, PCI and on board |
1206 | controllers" below. If you have a NE2000 card and are running on | |
1da177e4 LT |
1207 | an MCA system (a bus system used on some IBM PS/2 computers and |
1208 | laptops), say N here and Y to "NE/2 (ne2000 MCA version) support", | |
1209 | below. | |
1210 | ||
57ce45dd | 1211 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1212 | will be called ne. |
1213 | ||
1214 | config ZNET | |
1215 | tristate "Zenith Z-Note support (EXPERIMENTAL)" | |
a5532606 | 1216 | depends on NET_ISA && EXPERIMENTAL && ISA_DMA_API |
1da177e4 LT |
1217 | help |
1218 | The Zenith Z-Note notebook computer has a built-in network | |
1219 | (Ethernet) card, and this is the Linux driver for it. Note that the | |
1220 | IBM Thinkpad 300 is compatible with the Z-Note and is also supported | |
1221 | by this driver. Read the Ethernet-HOWTO, available from | |
1222 | <http://www.tldp.org/docs.html#howto>. | |
1223 | ||
1224 | config SEEQ8005 | |
1225 | tristate "SEEQ8005 support (EXPERIMENTAL)" | |
1226 | depends on NET_ISA && EXPERIMENTAL | |
1227 | help | |
1228 | This is a driver for the SEEQ 8005 network (Ethernet) card. If this | |
1229 | is for you, read the Ethernet-HOWTO, available from | |
1230 | <http://www.tldp.org/docs.html#howto>. | |
1231 | ||
57ce45dd | 1232 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1233 | will be called seeq8005. |
1234 | ||
1da177e4 LT |
1235 | config NE2_MCA |
1236 | tristate "NE/2 (ne2000 MCA version) support" | |
d1c0a65f | 1237 | depends on MCA_LEGACY |
1da177e4 LT |
1238 | select CRC32 |
1239 | help | |
1240 | If you have a network (Ethernet) card of this type, say Y and read | |
1241 | the Ethernet-HOWTO, available from | |
1242 | <http://www.tldp.org/docs.html#howto>. | |
1243 | ||
57ce45dd | 1244 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1245 | will be called ne2. |
1246 | ||
1247 | config IBMLANA | |
1248 | tristate "IBM LAN Adapter/A support" | |
e6353f30 | 1249 | depends on MCA |
1da177e4 LT |
1250 | ---help--- |
1251 | This is a Micro Channel Ethernet adapter. You need to set | |
1252 | CONFIG_MCA to use this driver. It is both available as an in-kernel | |
1253 | driver and as a module. | |
1254 | ||
57ce45dd | 1255 | To compile this driver as a module, choose M here. The only |
1da177e4 LT |
1256 | currently supported card is the IBM LAN Adapter/A for Ethernet. It |
1257 | will both support 16K and 32K memory windows, however a 32K window | |
1258 | gives a better security against packet losses. Usage of multiple | |
1259 | boards with this driver should be possible, but has not been tested | |
1260 | up to now due to lack of hardware. | |
1261 | ||
1262 | config IBMVETH | |
1263 | tristate "IBM LAN Virtual Ethernet support" | |
d1c0a65f | 1264 | depends on PPC_PSERIES |
1da177e4 LT |
1265 | ---help--- |
1266 | This driver supports virtual ethernet adapters on newer IBM iSeries | |
1267 | and pSeries systems. | |
1268 | ||
57ce45dd | 1269 | To compile this driver as a module, choose M here. The module will |
1da177e4 LT |
1270 | be called ibmveth. |
1271 | ||
1d3bb996 | 1272 | source "drivers/net/ibm_newemac/Kconfig" |
1da177e4 LT |
1273 | |
1274 | config NET_PCI | |
1275 | bool "EISA, VLB, PCI and on board controllers" | |
d1c0a65f | 1276 | depends on ISA || EISA || PCI |
1da177e4 LT |
1277 | help |
1278 | This is another class of network cards which attach directly to the | |
1279 | bus. If you have one of those, say Y and read the Ethernet-HOWTO, | |
1280 | available from <http://www.tldp.org/docs.html#howto>. | |
1281 | ||
1282 | Note that the answer to this question doesn't directly affect the | |
1283 | kernel: saying N will just cause the configurator to skip all | |
1284 | the questions about this class of network cards. If you say Y, you | |
1285 | will be asked for your specific card in the following questions. If | |
1286 | you are unsure, say Y. | |
1287 | ||
1288 | config PCNET32 | |
1289 | tristate "AMD PCnet32 PCI support" | |
1290 | depends on NET_PCI && PCI | |
1291 | select CRC32 | |
1292 | select MII | |
1293 | help | |
1294 | If you have a PCnet32 or PCnetPCI based network (Ethernet) card, | |
1295 | answer Y here and read the Ethernet-HOWTO, available from | |
1296 | <http://www.tldp.org/docs.html#howto>. | |
1297 | ||
57ce45dd | 1298 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1299 | will be called pcnet32. |
1300 | ||
1301 | config AMD8111_ETH | |
1302 | tristate "AMD 8111 (new PCI lance) support" | |
1303 | depends on NET_PCI && PCI | |
1304 | select CRC32 | |
1305 | select MII | |
1306 | help | |
1307 | If you have an AMD 8111-based PCI lance ethernet card, | |
1308 | answer Y here and read the Ethernet-HOWTO, available from | |
1309 | <http://www.tldp.org/docs.html#howto>. | |
1310 | ||
57ce45dd | 1311 | To compile this driver as a module, choose M here. The module |
1da177e4 | 1312 | will be called amd8111e. |
d1c0a65f | 1313 | |
1da177e4 LT |
1314 | config ADAPTEC_STARFIRE |
1315 | tristate "Adaptec Starfire/DuraLAN support" | |
1316 | depends on NET_PCI && PCI | |
1317 | select CRC32 | |
1318 | select MII | |
1319 | help | |
1320 | Say Y here if you have an Adaptec Starfire (or DuraLAN) PCI network | |
1321 | adapter. The DuraLAN chip is used on the 64 bit PCI boards from | |
1322 | Adaptec e.g. the ANA-6922A. The older 32 bit boards use the tulip | |
1323 | driver. | |
1324 | ||
1325 | To compile this driver as a module, choose M here: the module | |
1326 | will be called starfire. This is recommended. | |
1327 | ||
1da177e4 LT |
1328 | config AC3200 |
1329 | tristate "Ansel Communications EISA 3200 support (EXPERIMENTAL)" | |
1330 | depends on NET_PCI && (ISA || EISA) && EXPERIMENTAL | |
1331 | select CRC32 | |
1332 | help | |
1333 | If you have a network (Ethernet) card of this type, say Y and read | |
1334 | the Ethernet-HOWTO, available from | |
1335 | <http://www.tldp.org/docs.html#howto>. | |
1336 | ||
57ce45dd | 1337 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1338 | will be called ac3200. |
1339 | ||
1340 | config APRICOT | |
1341 | tristate "Apricot Xen-II on board Ethernet" | |
1342 | depends on NET_PCI && ISA | |
1343 | help | |
1344 | If you have a network (Ethernet) controller of this type, say Y and | |
1345 | read the Ethernet-HOWTO, available from | |
1346 | <http://www.tldp.org/docs.html#howto>. | |
1347 | ||
57ce45dd AB |
1348 | To compile this driver as a module, choose M here. The module |
1349 | will be called apricot. | |
1da177e4 LT |
1350 | |
1351 | config B44 | |
753f4920 | 1352 | tristate "Broadcom 440x/47xx ethernet support" |
46cb69cc | 1353 | depends on SSB_POSSIBLE && HAS_DMA |
753f4920 | 1354 | select SSB |
1da177e4 LT |
1355 | select MII |
1356 | help | |
753f4920 MB |
1357 | If you have a network (Ethernet) controller of this type, say Y |
1358 | or M and read the Ethernet-HOWTO, available from | |
1da177e4 LT |
1359 | <http://www.tldp.org/docs.html#howto>. |
1360 | ||
57ce45dd AB |
1361 | To compile this driver as a module, choose M here. The module |
1362 | will be called b44. | |
1da177e4 | 1363 | |
753f4920 MB |
1364 | # Auto-select SSB PCI-HOST support, if possible |
1365 | config B44_PCI_AUTOSELECT | |
1366 | bool | |
1367 | depends on B44 && SSB_PCIHOST_POSSIBLE | |
1368 | select SSB_PCIHOST | |
1369 | default y | |
1370 | ||
1371 | # Auto-select SSB PCICORE driver, if possible | |
1372 | config B44_PCICORE_AUTOSELECT | |
1373 | bool | |
1374 | depends on B44 && SSB_DRIVER_PCICORE_POSSIBLE | |
1375 | select SSB_DRIVER_PCICORE | |
1376 | default y | |
1377 | ||
1378 | config B44_PCI | |
1379 | bool | |
1380 | depends on B44_PCI_AUTOSELECT && B44_PCICORE_AUTOSELECT | |
1381 | default y | |
1382 | ||
1da177e4 | 1383 | config FORCEDETH |
82770086 AB |
1384 | tristate "nForce Ethernet support" |
1385 | depends on NET_PCI && PCI | |
1da177e4 LT |
1386 | help |
1387 | If you have a network (Ethernet) controller of this type, say Y and | |
1388 | read the Ethernet-HOWTO, available from | |
1389 | <http://www.tldp.org/docs.html#howto>. | |
1390 | ||
57ce45dd AB |
1391 | To compile this driver as a module, choose M here. The module |
1392 | will be called forcedeth. | |
1da177e4 | 1393 | |
e27cdba5 | 1394 | config FORCEDETH_NAPI |
bf45abeb | 1395 | bool "Use Rx Polling (NAPI) (EXPERIMENTAL)" |
e27cdba5 SH |
1396 | depends on FORCEDETH && EXPERIMENTAL |
1397 | help | |
1398 | NAPI is a new driver API designed to reduce CPU and interrupt load | |
1399 | when the driver is receiving lots of packets from the card. It is | |
1400 | still somewhat experimental and thus not yet enabled by default. | |
1401 | ||
1402 | If your estimated Rx load is 10kpps or more, or if the card will be | |
1403 | deployed on potentially unfriendly networks (e.g. in a firewall), | |
1404 | then say Y here. | |
1405 | ||
e27cdba5 | 1406 | If in doubt, say N. |
1da177e4 LT |
1407 | |
1408 | config CS89x0 | |
1409 | tristate "CS89x0 support" | |
0ac4ed9d GC |
1410 | depends on NET_ETHERNET && (ISA || EISA || MACH_IXDP2351 \ |
1411 | || ARCH_IXDP2X01 || ARCH_PNX010X || MACH_MX31ADS) | |
1da177e4 LT |
1412 | ---help--- |
1413 | Support for CS89x0 chipset based Ethernet cards. If you have a | |
1414 | network (Ethernet) card of this type, say Y and read the | |
1415 | Ethernet-HOWTO, available from | |
1416 | <http://www.tldp.org/docs.html#howto> as well as | |
1417 | <file:Documentation/networking/cs89x0.txt>. | |
1418 | ||
57ce45dd AB |
1419 | To compile this driver as a module, choose M here. The module |
1420 | will be called cs89x0. | |
1da177e4 | 1421 | |
0ac4ed9d GC |
1422 | config CS89x0_NONISA_IRQ |
1423 | def_bool y | |
1424 | depends on CS89x0 != n | |
1425 | depends on MACH_IXDP2351 || ARCH_IXDP2X01 || ARCH_PNX010X || MACH_MX31ADS | |
1426 | ||
1da177e4 LT |
1427 | config TC35815 |
1428 | tristate "TOSHIBA TC35815 Ethernet support" | |
eea221ce | 1429 | depends on NET_PCI && PCI && MIPS |
c6686fe3 | 1430 | select PHYLIB |
1da177e4 | 1431 | |
1da177e4 LT |
1432 | config E100 |
1433 | tristate "Intel(R) PRO/100+ support" | |
1434 | depends on NET_PCI && PCI | |
1435 | select MII | |
1436 | ---help--- | |
1437 | This driver supports Intel(R) PRO/100 family of adapters. | |
1438 | To verify that your adapter is supported, find the board ID number | |
1439 | on the adapter. Look for a label that has a barcode and a number | |
1440 | in the format 123456-001 (six digits hyphen three digits). | |
1441 | ||
1442 | Use the above information and the Adapter & Driver ID Guide at: | |
1443 | ||
1444 | <http://support.intel.com/support/network/adapter/pro100/21397.htm> | |
1445 | ||
1446 | to identify the adapter. | |
1447 | ||
1448 | For the latest Intel PRO/100 network driver for Linux, see: | |
1449 | ||
1450 | <http://appsr.intel.com/scripts-df/support_intel.asp> | |
1451 | ||
1452 | More specific information on configuring the driver is in | |
1453 | <file:Documentation/networking/e100.txt>. | |
1454 | ||
57ce45dd | 1455 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1456 | will be called e100. |
1457 | ||
1458 | config LNE390 | |
1459 | tristate "Mylex EISA LNE390A/B support (EXPERIMENTAL)" | |
1460 | depends on NET_PCI && EISA && EXPERIMENTAL | |
1461 | select CRC32 | |
1462 | help | |
1463 | If you have a network (Ethernet) card of this type, say Y and read | |
1464 | the Ethernet-HOWTO, available from | |
1465 | <http://www.tldp.org/docs.html#howto>. | |
1466 | ||
57ce45dd | 1467 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1468 | will be called lne390. |
1469 | ||
1470 | config FEALNX | |
1471 | tristate "Myson MTD-8xx PCI Ethernet support" | |
1472 | depends on NET_PCI && PCI | |
1473 | select CRC32 | |
1474 | select MII | |
1475 | help | |
1476 | Say Y here to support the Mysom MTD-800 family of PCI-based Ethernet | |
1477 | cards. Specifications and data at | |
1478 | <http://www.myson.com.hk/mtd/datasheet/>. | |
1479 | ||
1480 | config NATSEMI | |
1481 | tristate "National Semiconductor DP8381x series PCI Ethernet support" | |
1482 | depends on NET_PCI && PCI | |
1483 | select CRC32 | |
1484 | help | |
1485 | This driver is for the National Semiconductor DP83810 series, | |
1486 | which is used in cards from PureData, NetGear, Linksys | |
1487 | and others, including the 83815 chip. | |
1488 | More specific information and updates are available from | |
1489 | <http://www.scyld.com/network/natsemi.html>. | |
1490 | ||
1491 | config NE2K_PCI | |
1492 | tristate "PCI NE2000 and clones support (see help)" | |
1493 | depends on NET_PCI && PCI | |
1494 | select CRC32 | |
1495 | ---help--- | |
1496 | This driver is for NE2000 compatible PCI cards. It will not work | |
1497 | with ISA NE2000 cards (they have their own driver, "NE2000/NE1000 | |
1498 | support" below). If you have a PCI NE2000 network (Ethernet) card, | |
1499 | say Y and read the Ethernet-HOWTO, available from | |
1500 | <http://www.tldp.org/docs.html#howto>. | |
1501 | ||
1502 | This driver also works for the following NE2000 clone cards: | |
1503 | RealTek RTL-8029 Winbond 89C940 Compex RL2000 KTI ET32P2 | |
1504 | NetVin NV5000SC Via 86C926 SureCom NE34 Winbond | |
1505 | Holtek HT80232 Holtek HT80229 | |
1506 | ||
57ce45dd | 1507 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1508 | will be called ne2k-pci. |
1509 | ||
1510 | config NE3210 | |
1511 | tristate "Novell/Eagle/Microdyne NE3210 EISA support (EXPERIMENTAL)" | |
1512 | depends on NET_PCI && EISA && EXPERIMENTAL | |
1513 | select CRC32 | |
1514 | ---help--- | |
1515 | If you have a network (Ethernet) card of this type, say Y and read | |
1516 | the Ethernet-HOWTO, available from | |
1517 | <http://www.tldp.org/docs.html#howto>. Note that this driver | |
1518 | will NOT WORK for NE3200 cards as they are completely different. | |
1519 | ||
57ce45dd | 1520 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1521 | will be called ne3210. |
1522 | ||
1523 | config ES3210 | |
1524 | tristate "Racal-Interlan EISA ES3210 support (EXPERIMENTAL)" | |
1525 | depends on NET_PCI && EISA && EXPERIMENTAL | |
1526 | select CRC32 | |
1527 | help | |
1528 | If you have a network (Ethernet) card of this type, say Y and read | |
1529 | the Ethernet-HOWTO, available from | |
1530 | <http://www.tldp.org/docs.html#howto>. | |
1531 | ||
57ce45dd | 1532 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1533 | will be called es3210. |
1534 | ||
1535 | config 8139CP | |
1536 | tristate "RealTek RTL-8139 C+ PCI Fast Ethernet Adapter support (EXPERIMENTAL)" | |
1537 | depends on NET_PCI && PCI && EXPERIMENTAL | |
1538 | select CRC32 | |
1539 | select MII | |
1540 | help | |
1541 | This is a driver for the Fast Ethernet PCI network cards based on | |
1542 | the RTL8139C+ chips. If you have one of those, say Y and read | |
1543 | the Ethernet-HOWTO, available from | |
1544 | <http://www.tldp.org/docs.html#howto>. | |
1545 | ||
1546 | To compile this driver as a module, choose M here: the module | |
1547 | will be called 8139cp. This is recommended. | |
1548 | ||
1549 | config 8139TOO | |
f04e3f09 | 1550 | tristate "RealTek RTL-8129/8130/8139 PCI Fast Ethernet Adapter support" |
1da177e4 LT |
1551 | depends on NET_PCI && PCI |
1552 | select CRC32 | |
1553 | select MII | |
1554 | ---help--- | |
1555 | This is a driver for the Fast Ethernet PCI network cards based on | |
f04e3f09 AB |
1556 | the RTL 8129/8130/8139 chips. If you have one of those, say Y and |
1557 | read the Ethernet-HOWTO <http://www.tldp.org/docs.html#howto>. | |
1da177e4 LT |
1558 | |
1559 | To compile this driver as a module, choose M here: the module | |
1560 | will be called 8139too. This is recommended. | |
1561 | ||
1562 | config 8139TOO_PIO | |
1563 | bool "Use PIO instead of MMIO" | |
1564 | default y | |
1565 | depends on 8139TOO | |
1566 | help | |
1567 | This instructs the driver to use programmed I/O ports (PIO) instead | |
1568 | of PCI shared memory (MMIO). This can possibly solve some problems | |
1569 | in case your mainboard has memory consistency issues. If unsure, | |
1570 | say N. | |
1571 | ||
1572 | config 8139TOO_TUNE_TWISTER | |
1573 | bool "Support for uncommon RTL-8139 rev. K (automatic channel equalization)" | |
1574 | depends on 8139TOO | |
1575 | help | |
1576 | This implements a function which might come in handy in case you | |
1577 | are using low quality on long cabling. It is required for RealTek | |
1578 | RTL-8139 revision K boards, and totally unused otherwise. It tries | |
1579 | to match the transceiver to the cable characteristics. This is | |
1580 | experimental since hardly documented by the manufacturer. | |
1581 | If unsure, say Y. | |
1582 | ||
1583 | config 8139TOO_8129 | |
1584 | bool "Support for older RTL-8129/8130 boards" | |
1585 | depends on 8139TOO | |
1586 | help | |
1587 | This enables support for the older and uncommon RTL-8129 and | |
1588 | RTL-8130 chips, which support MII via an external transceiver, | |
1589 | instead of an internal one. Disabling this option will save some | |
1590 | memory by making the code size smaller. If unsure, say Y. | |
1591 | ||
1592 | config 8139_OLD_RX_RESET | |
1593 | bool "Use older RX-reset method" | |
1594 | depends on 8139TOO | |
1595 | help | |
1596 | The 8139too driver was recently updated to contain a more rapid | |
1597 | reset sequence, in the face of severe receive errors. This "new" | |
1598 | RX-reset method should be adequate for all boards. But if you | |
1599 | experience problems, you can enable this option to restore the | |
1600 | old RX-reset behavior. If unsure, say N. | |
1601 | ||
7a47dd7a | 1602 | config R6040 |
68334115 | 1603 | tristate "RDC R6040 Fast Ethernet Adapter support" |
7a47dd7a SW |
1604 | depends on NET_PCI && PCI |
1605 | select CRC32 | |
1606 | select MII | |
1607 | help | |
1608 | This is a driver for the R6040 Fast Ethernet MACs found in the | |
1609 | the RDC R-321x System-on-chips. | |
1610 | ||
1611 | To compile this driver as a module, choose M here: the module | |
1612 | will be called r6040. This is recommended. | |
1613 | ||
1da177e4 LT |
1614 | config SIS900 |
1615 | tristate "SiS 900/7016 PCI Fast Ethernet Adapter support" | |
1616 | depends on NET_PCI && PCI | |
1617 | select CRC32 | |
6da0f685 | 1618 | select MII |
1da177e4 LT |
1619 | ---help--- |
1620 | This is a driver for the Fast Ethernet PCI network cards based on | |
1621 | the SiS 900 and SiS 7016 chips. The SiS 900 core is also embedded in | |
c3cf560e | 1622 | SiS 630 and SiS 540 chipsets. |
1da177e4 LT |
1623 | |
1624 | This driver also supports AMD 79C901 HomePNA so that you can use | |
1625 | your phone line as a network cable. | |
1626 | ||
1627 | To compile this driver as a module, choose M here: the module | |
1628 | will be called sis900. This is recommended. | |
1629 | ||
1630 | config EPIC100 | |
1631 | tristate "SMC EtherPower II" | |
1632 | depends on NET_PCI && PCI | |
1633 | select CRC32 | |
1634 | select MII | |
1635 | help | |
1636 | This driver is for the SMC EtherPower II 9432 PCI Ethernet NIC, | |
1637 | which is based on the SMC83c17x (EPIC/100). | |
1638 | More specific information and updates are available from | |
1639 | <http://www.scyld.com/network/epic100.html>. | |
1640 | ||
2cb37728 SG |
1641 | config SMSC9420 |
1642 | tristate "SMSC LAN9420 PCI ethernet adapter support" | |
1643 | depends on NET_PCI && PCI | |
1644 | select CRC32 | |
1645 | select PHYLIB | |
1646 | select SMSC_PHY | |
1647 | help | |
1648 | This is a driver for SMSC's LAN9420 PCI ethernet adapter. | |
1649 | Say Y if you want it compiled into the kernel, | |
1650 | and read the Ethernet-HOWTO, available from | |
1651 | <http://www.linuxdoc.org/docs.html#howto>. | |
1652 | ||
1653 | This driver is also available as a module. The module will be | |
1654 | called smsc9420. If you want to compile it as a module, say M | |
1655 | here and read <file:Documentation/kbuild/modules.txt> | |
1656 | ||
1da177e4 LT |
1657 | config SUNDANCE |
1658 | tristate "Sundance Alta support" | |
1659 | depends on NET_PCI && PCI | |
1660 | select CRC32 | |
1661 | select MII | |
1662 | help | |
1663 | This driver is for the Sundance "Alta" chip. | |
1664 | More specific information and updates are available from | |
1665 | <http://www.scyld.com/network/sundance.html>. | |
1666 | ||
1667 | config SUNDANCE_MMIO | |
1668 | bool "Use MMIO instead of PIO" | |
1669 | depends on SUNDANCE | |
1670 | help | |
1671 | Enable memory-mapped I/O for interaction with Sundance NIC registers. | |
1672 | Do NOT enable this by default, PIO (enabled when MMIO is disabled) | |
1673 | is known to solve bugs on certain chips. | |
1674 | ||
1675 | If unsure, say N. | |
1676 | ||
1677 | config TLAN | |
1678 | tristate "TI ThunderLAN support" | |
93e16847 | 1679 | depends on NET_PCI && (PCI || EISA) |
1da177e4 LT |
1680 | ---help--- |
1681 | If you have a PCI Ethernet network card based on the ThunderLAN chip | |
1682 | which is supported by this driver, say Y and read the | |
1683 | Ethernet-HOWTO, available from | |
1684 | <http://www.tldp.org/docs.html#howto>. | |
1685 | ||
1686 | Devices currently supported by this driver are Compaq Netelligent, | |
1687 | Compaq NetFlex and Olicom cards. Please read the file | |
1688 | <file:Documentation/networking/tlan.txt> for more details. | |
1689 | ||
57ce45dd | 1690 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1691 | will be called tlan. |
1692 | ||
1693 | Please email feedback to <torben.mathiasen@compaq.com>. | |
1694 | ||
1695 | config VIA_RHINE | |
1696 | tristate "VIA Rhine support" | |
1697 | depends on NET_PCI && PCI | |
1698 | select CRC32 | |
1699 | select MII | |
1700 | help | |
1701 | If you have a VIA "Rhine" based network card (Rhine-I (VT86C100A), | |
1702 | Rhine-II (VT6102), or Rhine-III (VT6105)), say Y here. Rhine-type | |
1703 | Ethernet functions can also be found integrated on South Bridges | |
1704 | (e.g. VT8235). | |
1705 | ||
1706 | To compile this driver as a module, choose M here. The module | |
1707 | will be called via-rhine. | |
1708 | ||
1709 | config VIA_RHINE_MMIO | |
1710 | bool "Use MMIO instead of PIO" | |
1711 | depends on VIA_RHINE | |
1712 | help | |
1713 | This instructs the driver to use PCI shared memory (MMIO) instead of | |
1714 | programmed I/O ports (PIO). Enabling this gives an improvement in | |
1715 | processing time in parts of the driver. | |
1716 | ||
1717 | If unsure, say Y. | |
1718 | ||
bf345707 CEB |
1719 | config SC92031 |
1720 | tristate "Silan SC92031 PCI Fast Ethernet Adapter driver (EXPERIMENTAL)" | |
1721 | depends on NET_PCI && PCI && EXPERIMENTAL | |
1722 | select CRC32 | |
1723 | ---help--- | |
1724 | This is a driver for the Fast Ethernet PCI network cards based on | |
1725 | the Silan SC92031 chip (sometimes also called Rsltek 8139D). If you | |
1726 | have one of these, say Y here. | |
1727 | ||
1728 | To compile this driver as a module, choose M here: the module | |
1729 | will be called sc92031. This is recommended. | |
1730 | ||
d95b39c3 MC |
1731 | config CPMAC |
1732 | tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)" | |
8353ec7b | 1733 | depends on NET_ETHERNET && EXPERIMENTAL && AR7 && BROKEN |
d95b39c3 | 1734 | select PHYLIB |
d95b39c3 MC |
1735 | help |
1736 | TI AR7 CPMAC Ethernet support | |
1737 | ||
1da177e4 LT |
1738 | config NET_POCKET |
1739 | bool "Pocket and portable adapters" | |
d1c0a65f | 1740 | depends on PARPORT |
1da177e4 LT |
1741 | ---help--- |
1742 | Cute little network (Ethernet) devices which attach to the parallel | |
1743 | port ("pocket adapters"), commonly used with laptops. If you have | |
1744 | one of those, say Y and read the Ethernet-HOWTO, available from | |
1745 | <http://www.tldp.org/docs.html#howto>. | |
1746 | ||
1747 | If you want to plug a network (or some other) card into the PCMCIA | |
1748 | (or PC-card) slot of your laptop instead (PCMCIA is the standard for | |
1749 | credit card size extension cards used by all modern laptops), you | |
1750 | need the pcmcia-cs package (location contained in the file | |
1751 | <file:Documentation/Changes>) and you can say N here. | |
1752 | ||
1753 | Laptop users should read the Linux Laptop home page at | |
1754 | <http://www.linux-on-laptops.com/> or | |
1755 | Tuxmobil - Linux on Mobile Computers at <http://www.tuxmobil.org/>. | |
1756 | ||
1757 | Note that the answer to this question doesn't directly affect the | |
1758 | kernel: saying N will just cause the configurator to skip all | |
1759 | the questions about this class of network devices. If you say Y, you | |
1760 | will be asked for your specific device in the following questions. | |
1761 | ||
1762 | config ATP | |
1763 | tristate "AT-LAN-TEC/RealTek pocket adapter support" | |
32fa2bfc | 1764 | depends on NET_POCKET && PARPORT && X86 |
1da177e4 LT |
1765 | select CRC32 |
1766 | ---help--- | |
1767 | This is a network (Ethernet) device which attaches to your parallel | |
1768 | port. Read <file:drivers/net/atp.c> as well as the Ethernet-HOWTO, | |
1769 | available from <http://www.tldp.org/docs.html#howto>, if you | |
1770 | want to use this. If you intend to use this driver, you should have | |
1771 | said N to the "Parallel printer support", because the two drivers | |
1772 | don't like each other. | |
1773 | ||
1774 | To compile this driver as a module, choose M here: the module | |
1775 | will be called atp. | |
1776 | ||
1777 | config DE600 | |
1778 | tristate "D-Link DE600 pocket adapter support" | |
32fa2bfc | 1779 | depends on NET_POCKET && PARPORT |
1da177e4 LT |
1780 | ---help--- |
1781 | This is a network (Ethernet) device which attaches to your parallel | |
1782 | port. Read <file:Documentation/networking/DLINK.txt> as well as the | |
1783 | Ethernet-HOWTO, available from | |
1784 | <http://www.tldp.org/docs.html#howto>, if you want to use | |
1785 | this. It is possible to have several devices share a single parallel | |
1786 | port and it is safe to compile the corresponding drivers into the | |
1787 | kernel. | |
1788 | ||
1789 | To compile this driver as a module, choose M here: the module | |
1790 | will be called de600. | |
1791 | ||
1792 | config DE620 | |
1793 | tristate "D-Link DE620 pocket adapter support" | |
32fa2bfc | 1794 | depends on NET_POCKET && PARPORT |
1da177e4 LT |
1795 | ---help--- |
1796 | This is a network (Ethernet) device which attaches to your parallel | |
1797 | port. Read <file:Documentation/networking/DLINK.txt> as well as the | |
1798 | Ethernet-HOWTO, available from | |
1799 | <http://www.tldp.org/docs.html#howto>, if you want to use | |
1800 | this. It is possible to have several devices share a single parallel | |
1801 | port and it is safe to compile the corresponding drivers into the | |
1802 | kernel. | |
1803 | ||
1804 | To compile this driver as a module, choose M here: the module | |
1805 | will be called de620. | |
1806 | ||
1807 | config SGISEEQ | |
1808 | tristate "SGI Seeq ethernet controller support" | |
49b11bc3 | 1809 | depends on SGI_HAS_SEEQ |
1da177e4 LT |
1810 | help |
1811 | Say Y here if you have an Seeq based Ethernet network card. This is | |
1812 | used in many Silicon Graphics machines. | |
1813 | ||
1814 | config DECLANCE | |
1815 | tristate "DEC LANCE ethernet controller support" | |
d1c0a65f | 1816 | depends on MACH_DECSTATION |
1da177e4 LT |
1817 | select CRC32 |
1818 | help | |
1819 | This driver is for the series of Ethernet controllers produced by | |
1820 | DEC (now Compaq) based on the AMD Lance chipset, including the | |
1821 | DEPCA series. (This chipset is better known via the NE2100 cards.) | |
1822 | ||
1823 | config 68360_ENET | |
1824 | bool "Motorola 68360 ethernet controller" | |
1825 | depends on M68360 | |
1826 | help | |
1827 | Say Y here if you want to use the built-in ethernet controller of | |
1828 | the Motorola 68360 processor. | |
1829 | ||
1830 | config FEC | |
2af6921f | 1831 | bool "FEC ethernet controller (of ColdFire CPUs)" |
d4732d3c | 1832 | depends on M523x || M527x || M5272 || M528x || M520x || M532x |
1da177e4 LT |
1833 | help |
1834 | Say Y here if you want to use the built-in 10/100 Fast ethernet | |
2af6921f GU |
1835 | controller on some Motorola ColdFire processors. |
1836 | ||
1837 | config FEC2 | |
1838 | bool "Second FEC ethernet controller (on some ColdFire CPUs)" | |
1839 | depends on FEC | |
1840 | help | |
1841 | Say Y here if you want to use the second built-in 10/100 Fast | |
1842 | ethernet controller on some Motorola ColdFire processors. | |
1da177e4 | 1843 | |
5d031e9e DP |
1844 | config FEC_MPC52xx |
1845 | tristate "MPC52xx FEC driver" | |
847cdf42 | 1846 | depends on PPC_MPC52xx && PPC_BESTCOMM |
5d031e9e DP |
1847 | select CRC32 |
1848 | select PHYLIB | |
847cdf42 | 1849 | select PPC_BESTCOMM_FEC |
5d031e9e DP |
1850 | ---help--- |
1851 | This option enables support for the MPC5200's on-chip | |
1852 | Fast Ethernet Controller | |
1853 | If compiled as module, it will be called 'fec_mpc52xx.ko'. | |
1854 | ||
1855 | config FEC_MPC52xx_MDIO | |
1856 | bool "MPC52xx FEC MDIO bus driver" | |
1857 | depends on FEC_MPC52xx | |
1858 | default y | |
1859 | ---help--- | |
1860 | The MPC5200's FEC can connect to the Ethernet either with | |
1861 | an external MII PHY chip or 10 Mbps 7-wire interface | |
1862 | (Motorola? industry standard). | |
1863 | If your board uses an external PHY connected to FEC, enable this. | |
1864 | If not sure, enable. | |
1865 | If compiled as module, it will be called 'fec_mpc52xx_phy.ko'. | |
1866 | ||
1da177e4 LT |
1867 | config NE_H8300 |
1868 | tristate "NE2000 compatible support for H8/300" | |
d1c0a65f | 1869 | depends on H8300 |
1da177e4 LT |
1870 | help |
1871 | Say Y here if you want to use the NE2000 compatible | |
1872 | controller on the Renesas H8/300 processor. | |
1873 | ||
452c1ce2 CS |
1874 | config ATL2 |
1875 | tristate "Atheros L2 Fast Ethernet support" | |
1876 | depends on PCI | |
1877 | select CRC32 | |
1878 | select MII | |
1879 | help | |
1880 | This driver supports the Atheros L2 fast ethernet adapter. | |
1881 | ||
1882 | To compile this driver as a module, choose M here. The module | |
1883 | will be called atl2. | |
1884 | ||
48257c4f | 1885 | source "drivers/net/fs_enet/Kconfig" |
1da177e4 | 1886 | |
d1c0a65f | 1887 | endif # NET_ETHERNET |
1da177e4 LT |
1888 | |
1889 | # | |
1890 | # Gigabit Ethernet | |
1891 | # | |
1892 | ||
f30486d5 JE |
1893 | menuconfig NETDEV_1000 |
1894 | bool "Ethernet (1000 Mbit)" | |
cbcd2a4c | 1895 | depends on !UML |
f30486d5 | 1896 | default y |
06bfb7eb JE |
1897 | ---help--- |
1898 | Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common | |
1899 | type of Local Area Network (LAN) in universities and companies. | |
1900 | ||
1901 | Say Y here to get to see options for Gigabit Ethernet drivers. | |
1902 | This option alone does not add any kernel code. | |
1903 | Note that drivers supporting both 100 and 1000 MBit may be listed | |
1904 | under "Ethernet (10 or 100MBit)" instead. | |
1905 | ||
1906 | If you say N, all options in this submenu will be skipped and disabled. | |
f30486d5 JE |
1907 | |
1908 | if NETDEV_1000 | |
1da177e4 LT |
1909 | |
1910 | config ACENIC | |
1911 | tristate "Alteon AceNIC/3Com 3C985/NetGear GA620 Gigabit support" | |
1912 | depends on PCI | |
1913 | ---help--- | |
1914 | Say Y here if you have an Alteon AceNIC, 3Com 3C985(B), NetGear | |
1915 | GA620, SGI Gigabit or Farallon PN9000-SX PCI Gigabit Ethernet | |
1916 | adapter. The driver allows for using the Jumbo Frame option (9000 | |
1917 | bytes/frame) however it requires that your switches can handle this | |
1918 | as well. To enable Jumbo Frames, add `mtu 9000' to your ifconfig | |
1919 | line. | |
1920 | ||
1921 | To compile this driver as a module, choose M here: the | |
1922 | module will be called acenic. | |
1923 | ||
1924 | config ACENIC_OMIT_TIGON_I | |
1925 | bool "Omit support for old Tigon I based AceNICs" | |
1926 | depends on ACENIC | |
1927 | help | |
1928 | Say Y here if you only have Tigon II based AceNICs and want to leave | |
1929 | out support for the older Tigon I based cards which are no longer | |
1930 | being sold (ie. the original Alteon AceNIC and 3Com 3C985 (non B | |
1931 | version)). This will reduce the size of the driver object by | |
1932 | app. 100KB. If you are not sure whether your card is a Tigon I or a | |
1933 | Tigon II, say N here. | |
1934 | ||
1935 | The safe and default value for this is N. | |
1936 | ||
1937 | config DL2K | |
df950828 | 1938 | tristate "DL2000/TC902x-based Gigabit Ethernet support" |
1da177e4 LT |
1939 | depends on PCI |
1940 | select CRC32 | |
1941 | help | |
df950828 K |
1942 | This driver supports DL2000/TC902x-based Gigabit ethernet cards, |
1943 | which includes | |
1da177e4 LT |
1944 | D-Link DGE-550T Gigabit Ethernet Adapter. |
1945 | D-Link DL2000-based Gigabit Ethernet Adapter. | |
df950828 | 1946 | Sundance/Tamarack TC902x Gigabit Ethernet Adapter. |
1da177e4 LT |
1947 | |
1948 | To compile this driver as a module, choose M here: the | |
1949 | module will be called dl2k. | |
1950 | ||
1951 | config E1000 | |
1952 | tristate "Intel(R) PRO/1000 Gigabit Ethernet support" | |
1953 | depends on PCI | |
1954 | ---help--- | |
1955 | This driver supports Intel(R) PRO/1000 gigabit ethernet family of | |
1956 | adapters. For more information on how to identify your adapter, go | |
1957 | to the Adapter & Driver ID Guide at: | |
1958 | ||
1959 | <http://support.intel.com/support/network/adapter/pro100/21397.htm> | |
1960 | ||
1961 | For general information and support, go to the Intel support | |
1962 | website at: | |
1963 | ||
1964 | <http://support.intel.com> | |
1965 | ||
1966 | More specific information on configuring the driver is in | |
1967 | <file:Documentation/networking/e1000.txt>. | |
1968 | ||
57ce45dd | 1969 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
1970 | will be called e1000. |
1971 | ||
bc7f75fa AK |
1972 | config E1000E |
1973 | tristate "Intel(R) PRO/1000 PCI-Express Gigabit Ethernet support" | |
7ac86bf6 | 1974 | depends on PCI && (!SPARC32 || BROKEN) |
bc7f75fa AK |
1975 | ---help--- |
1976 | This driver supports the PCI-Express Intel(R) PRO/1000 gigabit | |
1977 | ethernet family of adapters. For PCI or PCI-X e1000 adapters, | |
1978 | use the regular e1000 driver For more information on how to | |
1979 | identify your adapter, go to the Adapter & Driver ID Guide at: | |
1980 | ||
1981 | <http://support.intel.com/support/network/adapter/pro100/21397.htm> | |
1982 | ||
1983 | For general information and support, go to the Intel support | |
1984 | website at: | |
1985 | ||
1986 | <http://support.intel.com> | |
1987 | ||
57ce45dd | 1988 | To compile this driver as a module, choose M here. The module |
bc7f75fa AK |
1989 | will be called e1000e. |
1990 | ||
ab7a9831 SH |
1991 | config IP1000 |
1992 | tristate "IP1000 Gigabit Ethernet support" | |
1993 | depends on PCI && EXPERIMENTAL | |
1994 | select MII | |
1995 | ---help--- | |
1996 | This driver supports IP1000 gigabit Ethernet cards. | |
1997 | ||
1998 | To compile this driver as a module, choose M here: the module | |
1999 | will be called ipg. This is recommended. | |
2000 | ||
9d5c8243 | 2001 | config IGB |
3ef6b235 | 2002 | tristate "Intel(R) 82575/82576 PCI-Express Gigabit Ethernet support" |
9d5c8243 AK |
2003 | depends on PCI |
2004 | ---help--- | |
3ef6b235 | 2005 | This driver supports Intel(R) 82575/82576 gigabit ethernet family of |
9d5c8243 AK |
2006 | adapters. For more information on how to identify your adapter, go |
2007 | to the Adapter & Driver ID Guide at: | |
2008 | ||
2009 | <http://support.intel.com/support/network/adapter/pro100/21397.htm> | |
2010 | ||
2011 | For general information and support, go to the Intel support | |
2012 | website at: | |
2013 | ||
2014 | <http://support.intel.com> | |
2015 | ||
2016 | More specific information on configuring the driver is in | |
2017 | <file:Documentation/networking/e1000.txt>. | |
2018 | ||
2bfc79de | 2019 | To compile this driver as a module, choose M here. The module |
9d5c8243 AK |
2020 | will be called igb. |
2021 | ||
d3352520 AD |
2022 | config IGB_LRO |
2023 | bool "Use software LRO" | |
2024 | depends on IGB && INET | |
2025 | select INET_LRO | |
2026 | ---help--- | |
2027 | Say Y here if you want to use large receive offload. | |
2028 | ||
2029 | If in doubt, say N. | |
2030 | ||
421e02f0 | 2031 | config IGB_DCA |
1d19ecfc | 2032 | bool "Direct Cache Access (DCA) Support" |
421e02f0 JK |
2033 | default y |
2034 | depends on IGB && DCA && !(IGB=y && DCA=m) | |
1d19ecfc JK |
2035 | ---help--- |
2036 | Say Y here if you want to use Direct Cache Access (DCA) in the | |
2037 | driver. DCA is a method for warming the CPU cache before data | |
2038 | is used, with the intent of lessening the impact of cache misses. | |
421e02f0 | 2039 | |
15d014d1 LB |
2040 | source "drivers/net/ixp2000/Kconfig" |
2041 | ||
1da177e4 LT |
2042 | config MYRI_SBUS |
2043 | tristate "MyriCOM Gigabit Ethernet support" | |
2044 | depends on SBUS | |
2045 | help | |
2046 | This driver supports MyriCOM Sbus gigabit Ethernet cards. | |
2047 | ||
2048 | To compile this driver as a module, choose M here: the module | |
2049 | will be called myri_sbus. This is recommended. | |
2050 | ||
2051 | config NS83820 | |
47c51431 | 2052 | tristate "National Semiconductor DP83820 support" |
1da177e4 LT |
2053 | depends on PCI |
2054 | help | |
2055 | This is a driver for the National Semiconductor DP83820 series | |
2056 | of gigabit ethernet MACs. Cards using this chipset include | |
2057 | the D-Link DGE-500T, PureData's PDP8023Z-TG, SMC's SMC9462TX, | |
2058 | SOHO-GA2000T, SOHO-GA2500T. The driver supports the use of | |
2059 | zero copy. | |
2060 | ||
2061 | config HAMACHI | |
2062 | tristate "Packet Engines Hamachi GNIC-II support" | |
2063 | depends on PCI | |
2064 | select MII | |
2065 | help | |
2066 | If you have a Gigabit Ethernet card of this type, say Y and read | |
2067 | the Ethernet-HOWTO, available from | |
2068 | <http://www.tldp.org/docs.html#howto>. | |
2069 | ||
57ce45dd | 2070 | To compile this driver as a module, choose M here. The module will be |
1da177e4 LT |
2071 | called hamachi. |
2072 | ||
2073 | config YELLOWFIN | |
2074 | tristate "Packet Engines Yellowfin Gigabit-NIC support (EXPERIMENTAL)" | |
2075 | depends on PCI && EXPERIMENTAL | |
2076 | select CRC32 | |
2077 | ---help--- | |
2078 | Say Y here if you have a Packet Engines G-NIC PCI Gigabit Ethernet | |
2079 | adapter or the SYM53C885 Ethernet controller. The Gigabit adapter is | |
2080 | used by the Beowulf Linux cluster project. See | |
2081 | <http://cesdis.gsfc.nasa.gov/linux/drivers/yellowfin.html> for more | |
2082 | information about this driver in particular and Beowulf in general. | |
2083 | ||
2084 | To compile this driver as a module, choose M here: the module | |
2085 | will be called yellowfin. This is recommended. | |
2086 | ||
2087 | config R8169 | |
2088 | tristate "Realtek 8169 gigabit ethernet support" | |
2089 | depends on PCI | |
2090 | select CRC32 | |
b7372492 | 2091 | select MII |
1da177e4 LT |
2092 | ---help--- |
2093 | Say Y here if you have a Realtek 8169 PCI Gigabit Ethernet adapter. | |
2094 | ||
2095 | To compile this driver as a module, choose M here: the module | |
2096 | will be called r8169. This is recommended. | |
2097 | ||
1da177e4 LT |
2098 | config R8169_VLAN |
2099 | bool "VLAN support" | |
2100 | depends on R8169 && VLAN_8021Q | |
2101 | ---help--- | |
2102 | Say Y here for the r8169 driver to support the functions required | |
2103 | by the kernel 802.1Q code. | |
865c652d | 2104 | |
1da177e4 LT |
2105 | If in doubt, say Y. |
2106 | ||
1a9e8549 | 2107 | config SB1250_MAC |
25a72dfe MR |
2108 | tristate "SB1250 Gigabit Ethernet support" |
2109 | depends on SIBYTE_SB1xxx_SOC | |
f5279ffd | 2110 | select PHYLIB |
25a72dfe MR |
2111 | ---help--- |
2112 | This driver supports Gigabit Ethernet interfaces based on the | |
2113 | Broadcom SiByte family of System-On-a-Chip parts. They include | |
2114 | the BCM1120, BCM1125, BCM1125H, BCM1250, BCM1255, BCM1280, BCM1455 | |
2115 | and BCM1480 chips. | |
2116 | ||
2117 | To compile this driver as a module, choose M here: the module | |
2118 | will be called sb1250-mac. | |
2119 | ||
890e8d0a | 2120 | config SIS190 |
e797637f | 2121 | tristate "SiS190/SiS191 gigabit ethernet support" |
e9985d53 AB |
2122 | depends on PCI |
2123 | select CRC32 | |
2124 | select MII | |
2125 | ---help--- | |
e797637f FR |
2126 | Say Y here if you have a SiS 190 PCI Fast Ethernet adapter or |
2127 | a SiS 191 PCI Gigabit Ethernet adapter. Both are expected to | |
2128 | appear in lan on motherboard designs which are based on SiS 965 | |
2129 | and SiS 966 south bridge. | |
e9985d53 AB |
2130 | |
2131 | To compile this driver as a module, choose M here: the module | |
2132 | will be called sis190. This is recommended. | |
890e8d0a | 2133 | |
baef58b1 | 2134 | config SKGE |
7a160c73 SH |
2135 | tristate "New SysKonnect GigaEthernet support" |
2136 | depends on PCI | |
baef58b1 SH |
2137 | select CRC32 |
2138 | ---help--- | |
2139 | This driver support the Marvell Yukon or SysKonnect SK-98xx/SK-95xx | |
2140 | and related Gigabit Ethernet adapters. It is a new smaller driver | |
46a60f2d | 2141 | with better performance and more complete ethtool support. |
baef58b1 SH |
2142 | |
2143 | It does not support the link failover and network management | |
5ad887fa | 2144 | features that "portable" vendor supplied sk98lin driver does. |
cd28ab6a | 2145 | |
c6f0d75a DD |
2146 | This driver supports adapters based on the original Yukon chipset: |
2147 | Marvell 88E8001, Belkin F5D5005, CNet GigaCard, DLink DGE-530T, | |
2148 | Linksys EG1032/EG1064, 3Com 3C940/3C940B, SysKonnect SK-9871/9872. | |
2149 | ||
2150 | It does not support the newer Yukon2 chipset: a separate driver, | |
2151 | sky2, is provided for Yukon2-based adapters. | |
2152 | ||
2153 | To compile this driver as a module, choose M here: the module | |
2154 | will be called skge. This is recommended. | |
cd28ab6a | 2155 | |
678aa1f6 SH |
2156 | config SKGE_DEBUG |
2157 | bool "Debugging interface" | |
2158 | depends on SKGE && DEBUG_FS | |
2159 | help | |
2160 | This option adds the ability to dump driver state for debugging. | |
2161 | The file debugfs/skge/ethX displays the state of the internal | |
2162 | transmit and receive rings. | |
2163 | ||
2164 | If unsure, say N. | |
2165 | ||
cd28ab6a | 2166 | config SKY2 |
8a3e3bfd | 2167 | tristate "SysKonnect Yukon2 support" |
f479b322 | 2168 | depends on PCI |
cd28ab6a SH |
2169 | select CRC32 |
2170 | ---help--- | |
cab00891 | 2171 | This driver supports Gigabit Ethernet adapters based on the |
c6f0d75a DD |
2172 | Marvell Yukon 2 chipset: |
2173 | Marvell 88E8021/88E8022/88E8035/88E8036/88E8038/88E8050/88E8052/ | |
2174 | 88E8053/88E8055/88E8061/88E8062, SysKonnect SK-9E21D/SK-9S21 | |
2175 | ||
f479b322 SH |
2176 | There is companion driver for the older Marvell Yukon and |
2177 | Genesis based adapters: skge. | |
cd28ab6a SH |
2178 | |
2179 | To compile this driver as a module, choose M here: the module | |
2180 | will be called sky2. This is recommended. | |
2181 | ||
3cf26753 SH |
2182 | config SKY2_DEBUG |
2183 | bool "Debugging interface" | |
2184 | depends on SKY2 && DEBUG_FS | |
2185 | help | |
2186 | This option adds the ability to dump driver state for debugging. | |
2187 | The file debugfs/sky2/ethX displays the state of the internal | |
2188 | transmit and receive rings. | |
2189 | ||
2190 | If unsure, say N. | |
1da177e4 LT |
2191 | |
2192 | config VIA_VELOCITY | |
2193 | tristate "VIA Velocity support" | |
73815538 | 2194 | depends on PCI |
1da177e4 LT |
2195 | select CRC32 |
2196 | select CRC_CCITT | |
2197 | select MII | |
2198 | help | |
2199 | If you have a VIA "Velocity" based network card say Y here. | |
2200 | ||
2201 | To compile this driver as a module, choose M here. The module | |
2202 | will be called via-velocity. | |
2203 | ||
2204 | config TIGON3 | |
2205 | tristate "Broadcom Tigon3 support" | |
2206 | depends on PCI | |
158d7abd | 2207 | select PHYLIB |
1da177e4 LT |
2208 | help |
2209 | This driver supports Broadcom Tigon3 based gigabit Ethernet cards. | |
2210 | ||
2211 | To compile this driver as a module, choose M here: the module | |
2212 | will be called tg3. This is recommended. | |
2213 | ||
b6016b76 MC |
2214 | config BNX2 |
2215 | tristate "Broadcom NetXtremeII support" | |
2216 | depends on PCI | |
fba9fe91 MC |
2217 | select CRC32 |
2218 | select ZLIB_INFLATE | |
b6016b76 MC |
2219 | help |
2220 | This driver supports Broadcom NetXtremeII gigabit Ethernet cards. | |
2221 | ||
2222 | To compile this driver as a module, choose M here: the module | |
2223 | will be called bnx2. This is recommended. | |
2224 | ||
aaec0fab JO |
2225 | config SPIDER_NET |
2226 | tristate "Spider Gigabit Ethernet driver" | |
3342cf0e | 2227 | depends on PCI && (PPC_IBM_CELL_BLADE || PPC_CELLEB) |
9b15879a | 2228 | select FW_LOADER |
aaec0fab JO |
2229 | help |
2230 | This driver supports the Gigabit Ethernet chips present on the | |
2231 | Cell Processor-Based Blades from IBM. | |
2232 | ||
5e123b84 ZR |
2233 | config TSI108_ETH |
2234 | tristate "Tundra TSI108 gigabit Ethernet support" | |
2235 | depends on TSI108_BRIDGE | |
2236 | help | |
2237 | This driver supports Tundra TSI108 gigabit Ethernet ports. | |
2238 | To compile this driver as a module, choose M here: the module | |
2239 | will be called tsi108_eth. | |
2240 | ||
02c18891 MM |
2241 | config GELIC_NET |
2242 | tristate "PS3 Gigabit Ethernet driver" | |
2243 | depends on PPC_PS3 | |
1d32e218 | 2244 | select PS3_SYS_MANAGER |
02c18891 MM |
2245 | help |
2246 | This driver supports the network device on the PS3 game | |
2247 | console. This driver has built-in support for Ethernet. | |
2248 | ||
2249 | To compile this driver as a module, choose M here: the | |
2250 | module will be called ps3_gelic. | |
2251 | ||
09dde54c | 2252 | config GELIC_WIRELESS |
97ed8390 JL |
2253 | bool "PS3 Wireless support" |
2254 | depends on GELIC_NET | |
2255 | select WIRELESS_EXT | |
2256 | help | |
2257 | This option adds the support for the wireless feature of PS3. | |
2258 | If you have the wireless-less model of PS3 or have no plan to | |
2259 | use wireless feature, disabling this option saves memory. As | |
2260 | the driver automatically distinguishes the models, you can | |
2261 | safely enable this option even if you have a wireless-less model. | |
09dde54c | 2262 | |
f409e348 MM |
2263 | config GELIC_WIRELESS_OLD_PSK_INTERFACE |
2264 | bool "PS3 Wireless private PSK interface (OBSOLETE)" | |
2265 | depends on GELIC_WIRELESS | |
2266 | help | |
2267 | This option retains the obsolete private interface to pass | |
2268 | the PSK from user space programs to the driver. The PSK | |
2269 | stands for 'Pre Shared Key' and is used for WPA[2]-PSK | |
2270 | (WPA-Personal) environment. | |
2271 | If WPA[2]-PSK is used and you need to use old programs that | |
2272 | support only this old interface, say Y. Otherwise N. | |
2273 | ||
2274 | If unsure, say N. | |
2275 | ||
1da177e4 LT |
2276 | config GIANFAR |
2277 | tristate "Gianfar Ethernet" | |
3a83156b | 2278 | depends on FSL_SOC |
bb40dcbb | 2279 | select PHYLIB |
bf41a7c5 | 2280 | select CRC32 |
1da177e4 | 2281 | help |
ef82a306 JL |
2282 | This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx, |
2283 | and MPC86xx family of chips, and the FEC on the 8540. | |
1da177e4 | 2284 | |
ce973b14 | 2285 | config UCC_GETH |
7d776cb5 TT |
2286 | tristate "Freescale QE Gigabit Ethernet" |
2287 | depends on QUICC_ENGINE | |
296baae2 | 2288 | select PHYLIB |
ce973b14 | 2289 | help |
7d776cb5 TT |
2290 | This driver supports the Gigabit Ethernet mode of the QUICC Engine, |
2291 | which is available on some Freescale SOCs. | |
ce973b14 | 2292 | |
ce973b14 LY |
2293 | config UGETH_MAGIC_PACKET |
2294 | bool "Magic Packet detection support" | |
2295 | depends on UCC_GETH | |
2296 | ||
d5b9049d MR |
2297 | config UGETH_TX_ON_DEMAND |
2298 | bool "Transmit on Demand support" | |
ce973b14 LY |
2299 | depends on UCC_GETH |
2300 | ||
1da177e4 | 2301 | config MV643XX_ETH |
9c1bbdfe | 2302 | tristate "Marvell Discovery (643XX) and Orion ethernet support" |
83aac8a3 | 2303 | depends on MV64360 || MV64X60 || (PPC_MULTIPLATFORM && PPC32) || PLAT_ORION |
ed94493f | 2304 | select PHYLIB |
1da177e4 | 2305 | help |
9c1bbdfe LB |
2306 | This driver supports the gigabit ethernet MACs in the |
2307 | Marvell Discovery PPC/MIPS chipset family (MV643XX) and | |
2308 | in the Marvell Orion ARM SoC family. | |
2309 | ||
2310 | Some boards that use the Discovery chipset are the Momenco | |
2311 | Ocelot C and Jaguar ATX and Pegasos II. | |
1da177e4 | 2312 | |
5a4faa87 RM |
2313 | config QLA3XXX |
2314 | tristate "QLogic QLA3XXX Network Driver Support" | |
2315 | depends on PCI | |
2316 | help | |
2317 | This driver supports QLogic ISP3XXX gigabit Ethernet cards. | |
2318 | ||
2319 | To compile this driver as a module, choose M here: the module | |
2320 | will be called qla3xxx. | |
2321 | ||
f3cc28c7 | 2322 | config ATL1 |
a6d1f369 JC |
2323 | tristate "Atheros/Attansic L1 Gigabit Ethernet support" |
2324 | depends on PCI | |
f3cc28c7 JC |
2325 | select CRC32 |
2326 | select MII | |
2327 | help | |
a6d1f369 JC |
2328 | This driver supports the Atheros/Attansic L1 gigabit ethernet |
2329 | adapter. | |
f3cc28c7 JC |
2330 | |
2331 | To compile this driver as a module, choose M here. The module | |
2332 | will be called atl1. | |
2333 | ||
a6a53252 JY |
2334 | config ATL1E |
2335 | tristate "Atheros L1E Gigabit Ethernet support (EXPERIMENTAL)" | |
2336 | depends on PCI && EXPERIMENTAL | |
2337 | select CRC32 | |
2338 | select MII | |
2339 | help | |
2340 | This driver supports the Atheros L1E gigabit ethernet adapter. | |
2341 | ||
2342 | To compile this driver as a module, choose M here. The module | |
2343 | will be called atl1e. | |
2344 | ||
43250ddd JY |
2345 | config ATL1C |
2346 | tristate "Atheros L1C Gigabit Ethernet support (EXPERIMENTAL)" | |
2347 | depends on PCI && EXPERIMENTAL | |
2348 | select CRC32 | |
2349 | select MII | |
2350 | help | |
2351 | This driver supports the Atheros L1C gigabit ethernet adapter. | |
2352 | ||
2353 | To compile this driver as a module, choose M here. The module | |
2354 | will be called atl1c. | |
2355 | ||
95252236 GFT |
2356 | config JME |
2357 | tristate "JMicron(R) PCI-Express Gigabit Ethernet support" | |
2358 | depends on PCI | |
2359 | select CRC32 | |
2360 | select MII | |
2361 | ---help--- | |
2362 | This driver supports the PCI-Express gigabit ethernet adapters | |
2363 | based on JMicron JMC250 chipset. | |
2364 | ||
2365 | To compile this driver as a module, choose M here. The module | |
2366 | will be called jme. | |
2367 | ||
f30486d5 | 2368 | endif # NETDEV_1000 |
1da177e4 LT |
2369 | |
2370 | # | |
2371 | # 10 Gigabit Ethernet | |
2372 | # | |
2373 | ||
f30486d5 JE |
2374 | menuconfig NETDEV_10000 |
2375 | bool "Ethernet (10000 Mbit)" | |
cbcd2a4c | 2376 | depends on !UML |
f30486d5 | 2377 | default y |
06bfb7eb JE |
2378 | ---help--- |
2379 | Say Y here to get to see options for 10 Gigabit Ethernet drivers. | |
2380 | This option alone does not add any kernel code. | |
2381 | ||
2382 | If you say N, all options in this submenu will be skipped and disabled. | |
f30486d5 JE |
2383 | |
2384 | if NETDEV_10000 | |
1da177e4 | 2385 | |
8199d3a7 CL |
2386 | config CHELSIO_T1 |
2387 | tristate "Chelsio 10Gb Ethernet support" | |
2388 | depends on PCI | |
57834ca1 | 2389 | select CRC32 |
8199d3a7 | 2390 | help |
f1d3d38a SH |
2391 | This driver supports Chelsio gigabit and 10-gigabit |
2392 | Ethernet cards. More information about adapter features and | |
2393 | performance tuning is in <file:Documentation/networking/cxgb.txt>. | |
8199d3a7 CL |
2394 | |
2395 | For general information about Chelsio and our products, visit | |
2396 | our website at <http://www.chelsio.com>. | |
2397 | ||
2398 | For customer support, please visit our customer support page at | |
2399 | <http://www.chelsio.com/support.htm>. | |
2400 | ||
2401 | Please send feedback to <linux-bugs@chelsio.com>. | |
2402 | ||
2403 | To compile this driver as a module, choose M here: the module | |
2404 | will be called cxgb. | |
2405 | ||
352c417d SH |
2406 | config CHELSIO_T1_1G |
2407 | bool "Chelsio gigabit Ethernet support" | |
2408 | depends on CHELSIO_T1 | |
2409 | help | |
2410 | Enables support for Chelsio's gigabit Ethernet PCI cards. If you | |
2411 | are using only 10G cards say 'N' here. | |
2412 | ||
58daa68a JB |
2413 | config CHELSIO_T3_DEPENDS |
2414 | tristate | |
2415 | depends on PCI && INET | |
2416 | default y | |
2417 | ||
4d22de3e | 2418 | config CHELSIO_T3 |
194c1fbe | 2419 | tristate "Chelsio Communications T3 10Gb Ethernet support" |
58daa68a | 2420 | depends on CHELSIO_T3_DEPENDS |
2e283962 | 2421 | select FW_LOADER |
b47385bd | 2422 | select INET_LRO |
194c1fbe DLR |
2423 | help |
2424 | This driver supports Chelsio T3-based gigabit and 10Gb Ethernet | |
2425 | adapters. | |
4d22de3e | 2426 | |
194c1fbe DLR |
2427 | For general information about Chelsio and our products, visit |
2428 | our website at <http://www.chelsio.com>. | |
4d22de3e | 2429 | |
194c1fbe DLR |
2430 | For customer support, please visit our customer support page at |
2431 | <http://www.chelsio.com/support.htm>. | |
4d22de3e | 2432 | |
194c1fbe | 2433 | Please send feedback to <linux-bugs@chelsio.com>. |
4d22de3e | 2434 | |
194c1fbe DLR |
2435 | To compile this driver as a module, choose M here: the module |
2436 | will be called cxgb3. | |
4d22de3e | 2437 | |
7a291083 JBT |
2438 | config EHEA |
2439 | tristate "eHEA Ethernet support" | |
60d5019b | 2440 | depends on IBMEBUS && INET && SPARSEMEM |
d4dc4ec9 | 2441 | select INET_LRO |
7a291083 JBT |
2442 | ---help--- |
2443 | This driver supports the IBM pSeries eHEA ethernet adapter. | |
2444 | ||
2445 | To compile the driver as a module, choose M here. The module | |
2446 | will be called ehea. | |
2447 | ||
01f2e4ea | 2448 | config ENIC |
eb8a4cb6 | 2449 | tristate "Cisco 10G Ethernet NIC support" |
01f2e4ea SF |
2450 | depends on PCI && INET |
2451 | select INET_LRO | |
2452 | help | |
2453 | This enables the support for the Cisco 10G Ethernet card. | |
2454 | ||
9a799d71 AK |
2455 | config IXGBE |
2456 | tristate "Intel(R) 10GbE PCI Express adapters support" | |
177db6ff MC |
2457 | depends on PCI && INET |
2458 | select INET_LRO | |
9a799d71 AK |
2459 | ---help--- |
2460 | This driver supports Intel(R) 10GbE PCI Express family of | |
2461 | adapters. For more information on how to identify your adapter, go | |
2462 | to the Adapter & Driver ID Guide at: | |
2463 | ||
2464 | <http://support.intel.com/support/network/adapter/pro100/21397.htm> | |
2465 | ||
2466 | For general information and support, go to the Intel support | |
2467 | website at: | |
2468 | ||
2469 | <http://support.intel.com> | |
2470 | ||
57ce45dd | 2471 | To compile this driver as a module, choose M here. The module |
9a799d71 AK |
2472 | will be called ixgbe. |
2473 | ||
5dd2d332 | 2474 | config IXGBE_DCA |
1d19ecfc | 2475 | bool "Direct Cache Access (DCA) Support" |
5dd2d332 JG |
2476 | default y |
2477 | depends on IXGBE && DCA && !(IXGBE=y && DCA=m) | |
1d19ecfc JK |
2478 | ---help--- |
2479 | Say Y here if you want to use Direct Cache Access (DCA) in the | |
2480 | driver. DCA is a method for warming the CPU cache before data | |
2481 | is used, with the intent of lessening the impact of cache misses. | |
5dd2d332 | 2482 | |
7a6b6f51 | 2483 | config IXGBE_DCB |
2f90b865 AD |
2484 | bool "Data Center Bridging (DCB) Support" |
2485 | default n | |
7a6b6f51 | 2486 | depends on IXGBE && DCB |
2f90b865 AD |
2487 | ---help--- |
2488 | Say Y here if you want to use Data Center Bridging (DCB) in the | |
2489 | driver. | |
2490 | ||
2491 | If unsure, say N. | |
2492 | ||
1da177e4 LT |
2493 | config IXGB |
2494 | tristate "Intel(R) PRO/10GbE support" | |
2495 | depends on PCI | |
2496 | ---help--- | |
9a799d71 AK |
2497 | This driver supports Intel(R) PRO/10GbE family of adapters for |
2498 | PCI-X type cards. For PCI-E type cards, use the "ixgbe" driver | |
2499 | instead. For more information on how to identify your adapter, go | |
1da177e4 LT |
2500 | to the Adapter & Driver ID Guide at: |
2501 | ||
2502 | <http://support.intel.com/support/network/adapter/pro100/21397.htm> | |
2503 | ||
2504 | For general information and support, go to the Intel support | |
2505 | website at: | |
2506 | ||
2507 | <http://support.intel.com> | |
2508 | ||
2509 | More specific information on configuring the driver is in | |
2510 | <file:Documentation/networking/ixgb.txt>. | |
2511 | ||
57ce45dd | 2512 | To compile this driver as a module, choose M here. The module |
1da177e4 LT |
2513 | will be called ixgb. |
2514 | ||
1da177e4 LT |
2515 | config S2IO |
2516 | tristate "S2IO 10Gbe XFrame NIC" | |
2517 | depends on PCI | |
2518 | ---help--- | |
2519 | This driver supports the 10Gbe XFrame NIC of S2IO. | |
9eb343ae AM |
2520 | More specific information on configuring the driver is in |
2521 | <file:Documentation/networking/s2io.txt>. | |
1da177e4 | 2522 | |
0da34b6d BG |
2523 | config MYRI10GE |
2524 | tristate "Myricom Myri-10G Ethernet support" | |
e0d5dab2 | 2525 | depends on PCI && INET |
0da34b6d BG |
2526 | select FW_LOADER |
2527 | select CRC32 | |
1e6e9342 | 2528 | select INET_LRO |
0da34b6d BG |
2529 | ---help--- |
2530 | This driver supports Myricom Myri-10G Dual Protocol interface in | |
2531 | Ethernet mode. If the eeprom on your board is not recent enough, | |
2532 | you will need a newer firmware image. | |
2533 | You may get this image or more information, at: | |
2534 | ||
d2794905 | 2535 | <http://www.myri.com/scs/download-Myri10GE.html> |
0da34b6d | 2536 | |
57ce45dd | 2537 | To compile this driver as a module, choose M here. The module |
0da34b6d BG |
2538 | will be called myri10ge. |
2539 | ||
5dd2d332 | 2540 | config MYRI10GE_DCA |
1d19ecfc | 2541 | bool "Direct Cache Access (DCA) Support" |
5dd2d332 JG |
2542 | default y |
2543 | depends on MYRI10GE && DCA && !(MYRI10GE=y && DCA=m) | |
1d19ecfc JK |
2544 | ---help--- |
2545 | Say Y here if you want to use Direct Cache Access (DCA) in the | |
2546 | driver. DCA is a method for warming the CPU cache before data | |
2547 | is used, with the intent of lessening the impact of cache misses. | |
5dd2d332 | 2548 | |
3d396eb1 AK |
2549 | config NETXEN_NIC |
2550 | tristate "NetXen Multi port (1/10) Gigabit Ethernet NIC" | |
5ac36615 | 2551 | depends on PCI |
3d396eb1 AK |
2552 | help |
2553 | This enables the support for NetXen's Gigabit Ethernet card. | |
2554 | ||
a3138df9 DM |
2555 | config NIU |
2556 | tristate "Sun Neptune 10Gbit Ethernet support" | |
2557 | depends on PCI | |
2558 | help | |
2559 | This enables support for cards based upon Sun's | |
2560 | Neptune chipset. | |
2561 | ||
f5cd7872 OJ |
2562 | config PASEMI_MAC |
2563 | tristate "PA Semi 1/10Gbit MAC" | |
5beaf7d6 | 2564 | depends on PPC_PASEMI && PCI |
bb6e9590 | 2565 | select PHYLIB |
28ae79f5 | 2566 | select INET_LRO |
f5cd7872 OJ |
2567 | help |
2568 | This driver supports the on-chip 1/10Gbit Ethernet controller on | |
2569 | PA Semi's PWRficient line of chips. | |
2570 | ||
c27a02cd YP |
2571 | config MLX4_EN |
2572 | tristate "Mellanox Technologies 10Gbit Ethernet support" | |
2573 | depends on PCI && INET | |
2574 | select MLX4_CORE | |
2575 | select INET_LRO | |
2576 | help | |
2577 | This driver supports Mellanox Technologies ConnectX Ethernet | |
2578 | devices. | |
2579 | ||
225c7b1f RD |
2580 | config MLX4_CORE |
2581 | tristate | |
2582 | depends on PCI | |
2583 | default n | |
2584 | ||
2585 | config MLX4_DEBUG | |
2586 | bool "Verbose debugging output" if (MLX4_CORE && EMBEDDED) | |
f550d94c | 2587 | depends on MLX4_CORE |
225c7b1f RD |
2588 | default y |
2589 | ---help--- | |
2590 | This option causes debugging code to be compiled into the | |
2591 | mlx4_core driver. The output can be turned on via the | |
2592 | debug_level module parameter (which can also be set after | |
2593 | the driver is loaded through sysfs). | |
2594 | ||
1a348ccc AG |
2595 | config TEHUTI |
2596 | tristate "Tehuti Networks 10G Ethernet" | |
2597 | depends on PCI | |
2598 | help | |
2599 | Tehuti Networks 10G Ethernet NIC | |
2600 | ||
a2fbb9ea ET |
2601 | config BNX2X |
2602 | tristate "Broadcom NetXtremeII 10Gb support" | |
2603 | depends on PCI | |
07b270ea | 2604 | select ZLIB_INFLATE |
34f80b04 | 2605 | select LIBCRC32C |
a2fbb9ea ET |
2606 | help |
2607 | This driver supports Broadcom NetXtremeII 10 gigabit Ethernet cards. | |
2608 | To compile this driver as a module, choose M here: the module | |
2609 | will be called bnx2x. This is recommended. | |
2610 | ||
c4e84bde RM |
2611 | config QLGE |
2612 | tristate "QLogic QLGE 10Gb Ethernet Driver Support" | |
2613 | depends on PCI | |
2614 | help | |
2615 | This driver supports QLogic ISP8XXX 10Gb Ethernet cards. | |
2616 | ||
2617 | To compile this driver as a module, choose M here: the module | |
2618 | will be called qlge. | |
2619 | ||
8ceee660 | 2620 | source "drivers/net/sfc/Kconfig" |
a2fbb9ea | 2621 | |
f30486d5 | 2622 | endif # NETDEV_10000 |
1da177e4 | 2623 | |
1da177e4 LT |
2624 | source "drivers/net/tokenring/Kconfig" |
2625 | ||
2626 | source "drivers/net/wireless/Kconfig" | |
2627 | ||
143ee2d5 IPG |
2628 | source "drivers/net/wimax/Kconfig" |
2629 | ||
5b2fc499 JG |
2630 | source "drivers/net/usb/Kconfig" |
2631 | ||
1da177e4 | 2632 | source "drivers/net/pcmcia/Kconfig" |
1da177e4 LT |
2633 | |
2634 | source "drivers/net/wan/Kconfig" | |
2635 | ||
2636 | source "drivers/atm/Kconfig" | |
2637 | ||
2638 | source "drivers/s390/net/Kconfig" | |
2639 | ||
0d160211 JF |
2640 | config XEN_NETDEV_FRONTEND |
2641 | tristate "Xen network device frontend driver" | |
2642 | depends on XEN | |
2643 | default y | |
2644 | help | |
2645 | The network device frontend driver allows the kernel to | |
2646 | access network devices exported exported by a virtual | |
2647 | machine containing a physical network device driver. The | |
2648 | frontend driver is intended for unprivileged guest domains; | |
2649 | if you are compiling a kernel for a Xen guest, you almost | |
2650 | certainly want to enable this. | |
2651 | ||
1da177e4 LT |
2652 | config ISERIES_VETH |
2653 | tristate "iSeries Virtual Ethernet driver support" | |
cbcd2a4c | 2654 | depends on PPC_ISERIES |
1da177e4 | 2655 | |
f89efd52 MP |
2656 | config RIONET |
2657 | tristate "RapidIO Ethernet over messaging driver support" | |
a81c52a8 | 2658 | depends on RAPIDIO |
f89efd52 MP |
2659 | |
2660 | config RIONET_TX_SIZE | |
2661 | int "Number of outbound queue entries" | |
2662 | depends on RIONET | |
2663 | default "128" | |
2664 | ||
2665 | config RIONET_RX_SIZE | |
2666 | int "Number of inbound queue entries" | |
2667 | depends on RIONET | |
2668 | default "128" | |
2669 | ||
1da177e4 | 2670 | config FDDI |
eb56092f | 2671 | tristate "FDDI driver support" |
e89a2cfb | 2672 | depends on (PCI || EISA || TC) |
1da177e4 LT |
2673 | help |
2674 | Fiber Distributed Data Interface is a high speed local area network | |
2675 | design; essentially a replacement for high speed Ethernet. FDDI can | |
2676 | run over copper or fiber. If you are connected to such a network and | |
2677 | want a driver for the FDDI card in your computer, say Y here (and | |
2678 | then also Y to the driver for your FDDI card, below). Most people | |
2679 | will say N. | |
2680 | ||
2681 | config DEFXX | |
e89a2cfb MR |
2682 | tristate "Digital DEFTA/DEFEA/DEFPA adapter support" |
2683 | depends on FDDI && (PCI || EISA || TC) | |
2684 | ---help--- | |
2685 | This is support for the DIGITAL series of TURBOchannel (DEFTA), | |
2686 | EISA (DEFEA) and PCI (DEFPA) controllers which can connect you | |
2687 | to a local FDDI network. | |
2688 | ||
2689 | To compile this driver as a module, choose M here: the module | |
2690 | will be called defxx. If unsure, say N. | |
2691 | ||
2692 | config DEFXX_MMIO | |
2693 | bool | |
2694 | prompt "Use MMIO instead of PIO" if PCI || EISA | |
2695 | depends on DEFXX | |
2696 | default n if PCI || EISA | |
2697 | default y | |
2698 | ---help--- | |
2699 | This instructs the driver to use EISA or PCI memory-mapped I/O | |
2700 | (MMIO) as appropriate instead of programmed I/O ports (PIO). | |
2701 | Enabling this gives an improvement in processing time in parts | |
2702 | of the driver, but it may cause problems with EISA (DEFEA) | |
2703 | adapters. TURBOchannel does not have the concept of I/O ports, | |
2704 | so MMIO is always used for these (DEFTA) adapters. | |
2705 | ||
2706 | If unsure, say N. | |
1da177e4 LT |
2707 | |
2708 | config SKFP | |
2709 | tristate "SysKonnect FDDI PCI support" | |
2710 | depends on FDDI && PCI | |
bc63eb9c | 2711 | select BITREVERSE |
1da177e4 LT |
2712 | ---help--- |
2713 | Say Y here if you have a SysKonnect FDDI PCI adapter. | |
2714 | The following adapters are supported by this driver: | |
2715 | - SK-5521 (SK-NET FDDI-UP) | |
2716 | - SK-5522 (SK-NET FDDI-UP DAS) | |
2717 | - SK-5541 (SK-NET FDDI-FP) | |
2718 | - SK-5543 (SK-NET FDDI-LP) | |
2719 | - SK-5544 (SK-NET FDDI-LP DAS) | |
2720 | - SK-5821 (SK-NET FDDI-UP64) | |
2721 | - SK-5822 (SK-NET FDDI-UP64 DAS) | |
2722 | - SK-5841 (SK-NET FDDI-FP64) | |
2723 | - SK-5843 (SK-NET FDDI-LP64) | |
2724 | - SK-5844 (SK-NET FDDI-LP64 DAS) | |
2725 | - Netelligent 100 FDDI DAS Fibre SC | |
2726 | - Netelligent 100 FDDI SAS Fibre SC | |
2727 | - Netelligent 100 FDDI DAS UTP | |
2728 | - Netelligent 100 FDDI SAS UTP | |
2729 | - Netelligent 100 FDDI SAS Fibre MIC | |
2730 | ||
2731 | Read <file:Documentation/networking/skfp.txt> for information about | |
2732 | the driver. | |
2733 | ||
2734 | Questions concerning this driver can be addressed to: | |
2735 | <linux@syskonnect.de> | |
2736 | ||
2737 | To compile this driver as a module, choose M here: the module | |
2738 | will be called skfp. This is recommended. | |
2739 | ||
2740 | config HIPPI | |
2741 | bool "HIPPI driver support (EXPERIMENTAL)" | |
cbcd2a4c | 2742 | depends on EXPERIMENTAL && INET && PCI |
1da177e4 LT |
2743 | help |
2744 | HIgh Performance Parallel Interface (HIPPI) is a 800Mbit/sec and | |
2745 | 1600Mbit/sec dual-simplex switched or point-to-point network. HIPPI | |
2746 | can run over copper (25m) or fiber (300m on multi-mode or 10km on | |
2747 | single-mode). HIPPI networks are commonly used for clusters and to | |
2748 | connect to super computers. If you are connected to a HIPPI network | |
2749 | and have a HIPPI network card in your computer that you want to use | |
2750 | under Linux, say Y here (you must also remember to enable the driver | |
2751 | for your HIPPI card below). Most people will say N here. | |
2752 | ||
2753 | config ROADRUNNER | |
2754 | tristate "Essential RoadRunner HIPPI PCI adapter support (EXPERIMENTAL)" | |
2755 | depends on HIPPI && PCI | |
2756 | help | |
2757 | Say Y here if this is your PCI HIPPI network card. | |
2758 | ||
2759 | To compile this driver as a module, choose M here: the module | |
2760 | will be called rrunner. If unsure, say N. | |
2761 | ||
2762 | config ROADRUNNER_LARGE_RINGS | |
2763 | bool "Use large TX/RX rings (EXPERIMENTAL)" | |
2764 | depends on ROADRUNNER | |
2765 | help | |
2766 | If you say Y here, the RoadRunner driver will preallocate up to 2 MB | |
2767 | of additional memory to allow for fastest operation, both for | |
2768 | transmitting and receiving. This memory cannot be used by any other | |
2769 | kernel code or by user space programs. Say Y here only if you have | |
2770 | the memory. | |
2771 | ||
2772 | config PLIP | |
2773 | tristate "PLIP (parallel port) support" | |
cbcd2a4c | 2774 | depends on PARPORT |
1da177e4 LT |
2775 | ---help--- |
2776 | PLIP (Parallel Line Internet Protocol) is used to create a | |
2777 | reasonably fast mini network consisting of two (or, rarely, more) | |
2778 | local machines. A PLIP link from a Linux box is a popular means to | |
2779 | install a Linux distribution on a machine which doesn't have a | |
2780 | CD-ROM drive (a minimal system has to be transferred with floppies | |
2781 | first). The kernels on both machines need to have this PLIP option | |
2782 | enabled for this to work. | |
2783 | ||
2784 | The PLIP driver has two modes, mode 0 and mode 1. The parallel | |
2785 | ports (the connectors at the computers with 25 holes) are connected | |
2786 | with "null printer" or "Turbo Laplink" cables which can transmit 4 | |
2787 | bits at a time (mode 0) or with special PLIP cables, to be used on | |
2788 | bidirectional parallel ports only, which can transmit 8 bits at a | |
2789 | time (mode 1); you can find the wiring of these cables in | |
2790 | <file:Documentation/networking/PLIP.txt>. The cables can be up to | |
2791 | 15m long. Mode 0 works also if one of the machines runs DOS/Windows | |
2792 | and has some PLIP software installed, e.g. the Crynwr PLIP packet | |
2793 | driver (<http://oak.oakland.edu/simtel.net/msdos/pktdrvr-pre.html>) | |
2794 | and winsock or NCSA's telnet. | |
2795 | ||
2796 | If you want to use PLIP, say Y and read the PLIP mini-HOWTO as well | |
2797 | as the NET-3-HOWTO, both available from | |
2798 | <http://www.tldp.org/docs.html#howto>. Note that the PLIP | |
2799 | protocol has been changed and this PLIP driver won't work together | |
2800 | with the PLIP support in Linux versions 1.0.x. This option enlarges | |
2801 | your kernel by about 8 KB. | |
2802 | ||
57ce45dd AB |
2803 | To compile this driver as a module, choose M here. The module |
2804 | will be called plip. If unsure, say Y or M, in case you buy | |
2805 | a laptop later. | |
1da177e4 LT |
2806 | |
2807 | config PPP | |
2808 | tristate "PPP (point-to-point protocol) support" | |
b6e37e55 | 2809 | select SLHC |
1da177e4 LT |
2810 | ---help--- |
2811 | PPP (Point to Point Protocol) is a newer and better SLIP. It serves | |
2812 | the same purpose: sending Internet traffic over telephone (and other | |
2813 | serial) lines. Ask your access provider if they support it, because | |
2814 | otherwise you can't use it; most Internet access providers these | |
2815 | days support PPP rather than SLIP. | |
2816 | ||
2817 | To use PPP, you need an additional program called pppd as described | |
2818 | in the PPP-HOWTO, available at | |
2819 | <http://www.tldp.org/docs.html#howto>. Make sure that you have | |
2820 | the version of pppd recommended in <file:Documentation/Changes>. | |
2821 | The PPP option enlarges your kernel by about 16 KB. | |
2822 | ||
2823 | There are actually two versions of PPP: the traditional PPP for | |
2824 | asynchronous lines, such as regular analog phone lines, and | |
2825 | synchronous PPP which can be used over digital ISDN lines for | |
2826 | example. If you want to use PPP over phone lines or other | |
2827 | asynchronous serial lines, you need to say Y (or M) here and also to | |
2828 | the next option, "PPP support for async serial ports". For PPP over | |
2829 | synchronous lines, you should say Y (or M) here and to "Support | |
2830 | synchronous PPP", below. | |
2831 | ||
2832 | If you said Y to "Version information on all symbols" above, then | |
2833 | you cannot compile the PPP driver into the kernel; you can then only | |
2834 | compile it as a module. To compile this driver as a module, choose M | |
57ce45dd | 2835 | here. The module will be called ppp_generic. |
1da177e4 LT |
2836 | |
2837 | config PPP_MULTILINK | |
2838 | bool "PPP multilink support (EXPERIMENTAL)" | |
2839 | depends on PPP && EXPERIMENTAL | |
2840 | help | |
2841 | PPP multilink is a protocol (defined in RFC 1990) which allows you | |
2842 | to combine several (logical or physical) lines into one logical PPP | |
2843 | connection, so that you can utilize your full bandwidth. | |
2844 | ||
2845 | This has to be supported at the other end as well and you need a | |
2846 | version of the pppd daemon which understands the multilink protocol. | |
2847 | ||
2848 | If unsure, say N. | |
2849 | ||
2850 | config PPP_FILTER | |
2851 | bool "PPP filtering" | |
2852 | depends on PPP | |
2853 | help | |
2854 | Say Y here if you want to be able to filter the packets passing over | |
2855 | PPP interfaces. This allows you to control which packets count as | |
2856 | activity (i.e. which packets will reset the idle timer or bring up | |
47c51431 | 2857 | a demand-dialed link) and which packets are to be dropped entirely. |
1da177e4 LT |
2858 | You need to say Y here if you wish to use the pass-filter and |
2859 | active-filter options to pppd. | |
2860 | ||
2861 | If unsure, say N. | |
2862 | ||
2863 | config PPP_ASYNC | |
2864 | tristate "PPP support for async serial ports" | |
2865 | depends on PPP | |
2866 | select CRC_CCITT | |
2867 | ---help--- | |
2868 | Say Y (or M) here if you want to be able to use PPP over standard | |
2869 | asynchronous serial ports, such as COM1 or COM2 on a PC. If you use | |
2870 | a modem (not a synchronous or ISDN modem) to contact your ISP, you | |
2871 | need this option. | |
2872 | ||
2873 | To compile this driver as a module, choose M here. | |
2874 | ||
2875 | If unsure, say Y. | |
2876 | ||
2877 | config PPP_SYNC_TTY | |
2878 | tristate "PPP support for sync tty ports" | |
2879 | depends on PPP | |
2880 | help | |
2881 | Say Y (or M) here if you want to be able to use PPP over synchronous | |
2882 | (HDLC) tty devices, such as the SyncLink adapter. These devices | |
2883 | are often used for high-speed leased lines like T1/E1. | |
2884 | ||
2885 | To compile this driver as a module, choose M here. | |
2886 | ||
2887 | config PPP_DEFLATE | |
2888 | tristate "PPP Deflate compression" | |
2889 | depends on PPP | |
2890 | select ZLIB_INFLATE | |
2891 | select ZLIB_DEFLATE | |
2892 | ---help--- | |
2893 | Support for the Deflate compression method for PPP, which uses the | |
2894 | Deflate algorithm (the same algorithm that gzip uses) to compress | |
2895 | each PPP packet before it is sent over the wire. The machine at the | |
2896 | other end of the PPP link (usually your ISP) has to support the | |
2897 | Deflate compression method as well for this to be useful. Even if | |
2898 | they don't support it, it is safe to say Y here. | |
2899 | ||
2900 | To compile this driver as a module, choose M here. | |
2901 | ||
2902 | config PPP_BSDCOMP | |
2903 | tristate "PPP BSD-Compress compression" | |
2904 | depends on PPP | |
2905 | ---help--- | |
2906 | Support for the BSD-Compress compression method for PPP, which uses | |
2907 | the LZW compression method to compress each PPP packet before it is | |
2908 | sent over the wire. The machine at the other end of the PPP link | |
2909 | (usually your ISP) has to support the BSD-Compress compression | |
2910 | method as well for this to be useful. Even if they don't support it, | |
2911 | it is safe to say Y here. | |
2912 | ||
2913 | The PPP Deflate compression method ("PPP Deflate compression", | |
2914 | above) is preferable to BSD-Compress, because it compresses better | |
2915 | and is patent-free. | |
2916 | ||
2917 | Note that the BSD compression code will always be compiled as a | |
2918 | module; it is called bsd_comp and will show up in the directory | |
2919 | modules once you have said "make modules". If unsure, say N. | |
2920 | ||
b3f9b92a MD |
2921 | config PPP_MPPE |
2922 | tristate "PPP MPPE compression (encryption) (EXPERIMENTAL)" | |
2923 | depends on PPP && EXPERIMENTAL | |
2924 | select CRYPTO | |
2925 | select CRYPTO_SHA1 | |
2926 | select CRYPTO_ARC4 | |
bcbaecbb | 2927 | select CRYPTO_ECB |
b3f9b92a MD |
2928 | ---help--- |
2929 | Support for the MPPE Encryption protocol, as employed by the | |
2930 | Microsoft Point-to-Point Tunneling Protocol. | |
2931 | ||
2932 | See http://pptpclient.sourceforge.net/ for information on | |
2933 | configuring PPTP clients and servers to utilize this method. | |
2934 | ||
1da177e4 LT |
2935 | config PPPOE |
2936 | tristate "PPP over Ethernet (EXPERIMENTAL)" | |
2937 | depends on EXPERIMENTAL && PPP | |
2938 | help | |
2939 | Support for PPP over Ethernet. | |
2940 | ||
2941 | This driver requires the latest version of pppd from the CVS | |
2942 | repository at cvs.samba.org. Alternatively, see the | |
2943 | RoaringPenguin package (<http://www.roaringpenguin.com/pppoe>) | |
2944 | which contains instruction on how to use this driver (under | |
2945 | the heading "Kernel mode PPPoE"). | |
2946 | ||
2947 | config PPPOATM | |
2948 | tristate "PPP over ATM" | |
2949 | depends on ATM && PPP | |
2950 | help | |
2951 | Support PPP (Point to Point Protocol) encapsulated in ATM frames. | |
2952 | This implementation does not yet comply with section 8 of RFC2364, | |
2953 | which can lead to bad results if the ATM peer loses state and | |
2954 | changes its encapsulation unilaterally. | |
2955 | ||
3557baab JC |
2956 | config PPPOL2TP |
2957 | tristate "PPP over L2TP (EXPERIMENTAL)" | |
143cf353 | 2958 | depends on EXPERIMENTAL && PPP && INET |
3557baab JC |
2959 | help |
2960 | Support for PPP-over-L2TP socket family. L2TP is a protocol | |
2961 | used by ISPs and enterprises to tunnel PPP traffic over UDP | |
2962 | tunnels. L2TP is replacing PPTP for VPN uses. | |
2963 | ||
2964 | This kernel component handles only L2TP data packets: a | |
2965 | userland daemon handles L2TP the control protocol (tunnel | |
2966 | and session setup). One such daemon is OpenL2TP | |
2967 | (http://openl2tp.sourceforge.net/). | |
2968 | ||
1da177e4 LT |
2969 | config SLIP |
2970 | tristate "SLIP (serial line) support" | |
1da177e4 LT |
2971 | ---help--- |
2972 | Say Y if you intend to use SLIP or CSLIP (compressed SLIP) to | |
2973 | connect to your Internet service provider or to connect to some | |
2974 | other local Unix box or if you want to configure your Linux box as a | |
2975 | Slip/CSlip server for other people to dial in. SLIP (Serial Line | |
2976 | Internet Protocol) is a protocol used to send Internet traffic over | |
2977 | serial connections such as telephone lines or null modem cables; | |
2978 | nowadays, the protocol PPP is more commonly used for this same | |
2979 | purpose. | |
2980 | ||
2981 | Normally, your access provider has to support SLIP in order for you | |
2982 | to be able to use it, but there is now a SLIP emulator called SLiRP | |
2983 | around (available from | |
2984 | <ftp://ibiblio.org/pub/Linux/system/network/serial/>) which | |
2985 | allows you to use SLIP over a regular dial up shell connection. If | |
2986 | you plan to use SLiRP, make sure to say Y to CSLIP, below. The | |
2987 | NET-3-HOWTO, available from | |
2988 | <http://www.tldp.org/docs.html#howto>, explains how to | |
2989 | configure SLIP. Note that you don't need this option if you just | |
2990 | want to run term (term is a program which gives you almost full | |
2991 | Internet connectivity if you have a regular dial up shell account on | |
2992 | some Internet connected Unix computer. Read | |
2993 | <http://www.bart.nl/~patrickr/term-howto/Term-HOWTO.html>). SLIP | |
2994 | support will enlarge your kernel by about 4 KB. If unsure, say N. | |
2995 | ||
57ce45dd AB |
2996 | To compile this driver as a module, choose M here. The module |
2997 | will be called slip. | |
1da177e4 LT |
2998 | |
2999 | config SLIP_COMPRESSED | |
3000 | bool "CSLIP compressed headers" | |
3001 | depends on SLIP | |
b6e37e55 | 3002 | select SLHC |
1da177e4 LT |
3003 | ---help--- |
3004 | This protocol is faster than SLIP because it uses compression on the | |
3005 | TCP/IP headers (not on the data itself), but it has to be supported | |
3006 | on both ends. Ask your access provider if you are not sure and | |
3007 | answer Y, just in case. You will still be able to use plain SLIP. If | |
3008 | you plan to use SLiRP, the SLIP emulator (available from | |
3009 | <ftp://ibiblio.org/pub/Linux/system/network/serial/>) which | |
3010 | allows you to use SLIP over a regular dial up shell connection, you | |
3011 | definitely want to say Y here. The NET-3-HOWTO, available from | |
3012 | <http://www.tldp.org/docs.html#howto>, explains how to configure | |
3013 | CSLIP. This won't enlarge your kernel. | |
3014 | ||
b6e37e55 RB |
3015 | config SLHC |
3016 | tristate | |
3017 | help | |
3018 | This option enables Van Jacobsen serial line header compression | |
3019 | routines. | |
3020 | ||
1da177e4 LT |
3021 | config SLIP_SMART |
3022 | bool "Keepalive and linefill" | |
3023 | depends on SLIP | |
3024 | help | |
3025 | Adds additional capabilities to the SLIP driver to support the | |
3026 | RELCOM line fill and keepalive monitoring. Ideal on poor quality | |
3027 | analogue lines. | |
3028 | ||
3029 | config SLIP_MODE_SLIP6 | |
3030 | bool "Six bit SLIP encapsulation" | |
3031 | depends on SLIP | |
3032 | help | |
3033 | Just occasionally you may need to run IP over hostile serial | |
3034 | networks that don't pass all control characters or are only seven | |
3035 | bit. Saying Y here adds an extra mode you can use with SLIP: | |
3036 | "slip6". In this mode, SLIP will only send normal ASCII symbols over | |
3037 | the serial device. Naturally, this has to be supported at the other | |
3038 | end of the link as well. It's good enough, for example, to run IP | |
3039 | over the async ports of a Camtec JNT Pad. If unsure, say N. | |
3040 | ||
3041 | config NET_FC | |
3042 | bool "Fibre Channel driver support" | |
cbcd2a4c | 3043 | depends on SCSI && PCI |
1da177e4 LT |
3044 | help |
3045 | Fibre Channel is a high speed serial protocol mainly used to connect | |
3046 | large storage devices to the computer; it is compatible with and | |
3047 | intended to replace SCSI. | |
3048 | ||
3049 | If you intend to use Fibre Channel, you need to have a Fibre channel | |
3050 | adaptor card in your computer; say Y here and to the driver for your | |
3051 | adaptor below. You also should have said Y to "SCSI support" and | |
3052 | "SCSI generic support". | |
3053 | ||
1da177e4 LT |
3054 | config NETCONSOLE |
3055 | tristate "Network console logging support (EXPERIMENTAL)" | |
5e43db77 | 3056 | depends on EXPERIMENTAL |
1da177e4 LT |
3057 | ---help--- |
3058 | If you want to log kernel messages over the network, enable this. | |
3059 | See <file:Documentation/networking/netconsole.txt> for details. | |
3060 | ||
0bcc1816 SS |
3061 | config NETCONSOLE_DYNAMIC |
3062 | bool "Dynamic reconfiguration of logging targets (EXPERIMENTAL)" | |
3063 | depends on NETCONSOLE && SYSFS && EXPERIMENTAL | |
3064 | select CONFIGFS_FS | |
3065 | help | |
3066 | This option enables the ability to dynamically reconfigure target | |
3067 | parameters (interface, IP addresses, port numbers, MAC addresses) | |
3068 | at runtime through a userspace interface exported using configfs. | |
3069 | See <file:Documentation/networking/netconsole.txt> for details. | |
3070 | ||
54208991 RD |
3071 | config NETPOLL |
3072 | def_bool NETCONSOLE | |
3073 | ||
54208991 RD |
3074 | config NETPOLL_TRAP |
3075 | bool "Netpoll traffic trapping" | |
3076 | default n | |
3077 | depends on NETPOLL | |
3078 | ||
3079 | config NET_POLL_CONTROLLER | |
3080 | def_bool NETPOLL | |
3081 | ||
296f96fc RR |
3082 | config VIRTIO_NET |
3083 | tristate "Virtio network driver (EXPERIMENTAL)" | |
3084 | depends on EXPERIMENTAL && VIRTIO | |
3085 | ---help--- | |
0ad07ec1 AL |
3086 | This is the virtual network driver for virtio. It can be used with |
3087 | lguest or QEMU based VMMs (like KVM or Xen). Say Y or M. | |
296f96fc | 3088 | |
d1c0a65f | 3089 | endif # NETDEVICES |