projects / deliverable / linux.git / blame
| Commit | Line | Data |
|---|---|---|
| bcc43a4b AB |
1 | config WILC1000 |
| 2 | tristate | |
| 750ffe9b | 3 | select WIRELESS_EXT |
| 9535ebc5 | 4 | ---help--- |
| 750ffe9b | 5 | This module only support IEEE 802.11n WiFi. |
| 9535ebc5 | 6 | |
| bcc43a4b | 7 | config WILC1000_SDIO |
| 750ffe9b AB |
8 | tristate "Atmel WILC1000 SDIO (WiFi only)" |
| 9 | depends on CFG80211 && INET && MMC | |
| bcc43a4b | 10 | select WILC1000 |
| 9535ebc5 | 11 | ---help--- |
| 5f8966d9 TC |
12 | This module adds support for the SDIO interface of adapters using |
| 13 | WILC1000 chipset. The Atmel WILC1000 SDIO is a full speed interface. | |
| 14 | It meets SDIO card specification version 2.0. The interface supports | |
| 15 | the 1-bit/4-bit SD transfer mode at the clock range of 0-50 MHz. | |
| 16 | The host can use this interface to read and write from any register | |
| 17 | within the chip as well as configure the WILC1000 for data DMA. | |
| 18 | To use this interface, pin9 (SDIO_SPI_CFG) must be grounded. Select | |
| 19 | this if your platform is using the SDIO bus. | |
| c5c77ba1 | 20 | |
| bcc43a4b | 21 | config WILC1000_SPI |
| 750ffe9b AB |
22 | tristate "Atmel WILC1000 SPI (WiFi only)" |
| 23 | depends on CFG80211 && INET && SPI | |
| bcc43a4b | 24 | select WILC1000 |
| 9535ebc5 | 25 | ---help--- |
| 5f8966d9 TC |
26 | This module adds support for the SPI interface of adapters using |
| 27 | WILC1000 chipset. The Atmel WILC1000 has a Serial Peripheral | |
| 28 | Interface (SPI) that operates as a SPI slave. This SPI interface can | |
| 29 | be used for control and for serial I/O of 802.11 data. The SPI is a | |
| 30 | full-duplex slave synchronous serial interface that is available | |
| 31 | immediately following reset when pin 9 (SDIO_SPI_CFG) is tied to | |
| 32 | VDDIO. Select this if your platform is using the SPI bus. | |
| 750ffe9b | 33 | |
| c5c77ba1 | 34 | config WILC1000_HW_OOB_INTR |
| 750ffe9b | 35 | bool "WILC1000 out of band interrupt" |
| bcc43a4b | 36 | depends on WILC1000_SDIO |
| 9535ebc5 AB |
37 | default n |
| 38 | ---help--- | |
| 5f8966d9 TC |
39 | This option enables out-of-band interrupt support for the WILC1000 |
| 40 | chipset. This OOB interrupt is intended to provide a faster interrupt | |
| 41 | mechanism for SDIO host controllers that don't support SDIO interrupt. | |
| 42 | Select this option If the SDIO host controller in your platform | |
| 43 | doesn't support SDIO time devision interrupt. |