Fix common misspellings
[deliverable/linux.git] / include / linux / amba / mmci.h
CommitLineData
1da177e4 1/*
6ef297f8 2 * include/linux/amba/mmci.h
1da177e4 3 */
6ef297f8
LW
4#ifndef AMBA_MMCI_H
5#define AMBA_MMCI_H
1da177e4 6
f74d132c 7#include <linux/mmc/host.h>
1da177e4 8
c8ebae37
RK
9/* Just some dummy forwarding */
10struct dma_chan;
11
808d97cc
LW
12/**
13 * struct mmci_platform_data - platform configuration for the MMCI
14 * (also known as PL180) block.
15 * @f_max: the maximum operational frequency for this host in this
16 * platform configuration. When this is specified it takes precedence
17 * over the module parameter for the same frequency.
18 * @ocr_mask: available voltages on the 4 pins from the block, this
19 * is ignored if a regulator is used, see the MMC_VDD_* masks in
20 * mmc/host.h
bb8f563c
RV
21 * @vdd_handler: a callback function to translate a MMC_VDD_*
22 * mask into a value to be binary (or set some other custom bits
23 * in MMCIPWR) or:ed and written into the MMCIPWR register of the
24 * block. May also control external power based on the power_mode.
808d97cc
LW
25 * @status: if no GPIO read function was given to the block in
26 * gpio_wp (below) this function will be called to determine
27 * whether a card is present in the MMC slot or not
28 * @gpio_wp: read this GPIO pin to see if the card is write protected
29 * @gpio_cd: read this GPIO pin to detect card insertion
29719445 30 * @cd_invert: true if the gpio_cd pin value is active low
808d97cc
LW
31 * @capabilities: the capabilities of the block as implemented in
32 * this platform, signify anything MMC_CAP_* from mmc/host.h
25985edc 33 * @dma_filter: function used to select an appropriate RX and TX
c8ebae37
RK
34 * DMA channel to be used for DMA, if and only if you're deploying the
35 * generic DMA engine
36 * @dma_rx_param: parameter passed to the DMA allocation
25985edc 37 * filter in order to select an appropriate RX channel. If
c8ebae37
RK
38 * there is a bidirectional RX+TX channel, then just specify
39 * this and leave dma_tx_param set to NULL
40 * @dma_tx_param: parameter passed to the DMA allocation
25985edc 41 * filter in order to select an appropriate TX channel. If this
c8ebae37
RK
42 * is NULL the driver will attempt to use the RX channel as a
43 * bidirectional channel
808d97cc 44 */
6ef297f8 45struct mmci_platform_data {
808d97cc
LW
46 unsigned int f_max;
47 unsigned int ocr_mask;
bb8f563c
RV
48 u32 (*vdd_handler)(struct device *, unsigned int vdd,
49 unsigned char power_mode);
1da177e4 50 unsigned int (*status)(struct device *);
7fb2bbf4
RK
51 int gpio_wp;
52 int gpio_cd;
29719445 53 bool cd_invert;
9e6c82cd 54 unsigned long capabilities;
c8ebae37
RK
55 bool (*dma_filter)(struct dma_chan *chan, void *filter_param);
56 void *dma_rx_param;
57 void *dma_tx_param;
1da177e4
LT
58};
59
60#endif
This page took 0.530522 seconds and 5 git commands to generate.