Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | /* |
2 | * linux/include/linux/mtd/nand.h | |
3 | * | |
a1452a37 DW |
4 | * Copyright © 2000-2010 David Woodhouse <dwmw2@infradead.org> |
5 | * Steven J. Hill <sjhill@realitydiluted.com> | |
6 | * Thomas Gleixner <tglx@linutronix.de> | |
1da177e4 | 7 | * |
1da177e4 LT |
8 | * This program is free software; you can redistribute it and/or modify |
9 | * it under the terms of the GNU General Public License version 2 as | |
10 | * published by the Free Software Foundation. | |
11 | * | |
2c0a2bed TG |
12 | * Info: |
13 | * Contains standard defines and IDs for NAND flash devices | |
1da177e4 | 14 | * |
2c0a2bed TG |
15 | * Changelog: |
16 | * See git changelog. | |
1da177e4 LT |
17 | */ |
18 | #ifndef __LINUX_MTD_NAND_H | |
19 | #define __LINUX_MTD_NAND_H | |
20 | ||
1da177e4 LT |
21 | #include <linux/wait.h> |
22 | #include <linux/spinlock.h> | |
23 | #include <linux/mtd/mtd.h> | |
30631cb8 | 24 | #include <linux/mtd/flashchip.h> |
c62d81bc | 25 | #include <linux/mtd/bbm.h> |
1da177e4 LT |
26 | |
27 | struct mtd_info; | |
5e81e88a | 28 | struct nand_flash_dev; |
5844feea BN |
29 | struct device_node; |
30 | ||
1da177e4 | 31 | /* Scan and identify a NAND device */ |
a0491fc4 SAS |
32 | extern int nand_scan(struct mtd_info *mtd, int max_chips); |
33 | /* | |
34 | * Separate phases of nand_scan(), allowing board driver to intervene | |
35 | * and override command or ECC setup according to flash type. | |
36 | */ | |
5e81e88a DW |
37 | extern int nand_scan_ident(struct mtd_info *mtd, int max_chips, |
38 | struct nand_flash_dev *table); | |
3b85c321 DW |
39 | extern int nand_scan_tail(struct mtd_info *mtd); |
40 | ||
1da177e4 | 41 | /* Free resources held by the NAND device */ |
a0491fc4 | 42 | extern void nand_release(struct mtd_info *mtd); |
1da177e4 | 43 | |
b77d95c7 DW |
44 | /* Internal helper for board drivers which need to override command function */ |
45 | extern void nand_wait_ready(struct mtd_info *mtd); | |
46 | ||
7854d3f7 | 47 | /* locks all blocks present in the device */ |
7d70f334 VS |
48 | extern int nand_lock(struct mtd_info *mtd, loff_t ofs, uint64_t len); |
49 | ||
7854d3f7 | 50 | /* unlocks specified locked blocks */ |
7d70f334 VS |
51 | extern int nand_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len); |
52 | ||
1da177e4 LT |
53 | /* The maximum number of NAND chips in an array */ |
54 | #define NAND_MAX_CHIPS 8 | |
55 | ||
1da177e4 LT |
56 | /* |
57 | * Constants for hardware specific CLE/ALE/NCE function | |
7abd3ef9 TG |
58 | * |
59 | * These are bits which can be or'ed to set/clear multiple | |
60 | * bits in one go. | |
61 | */ | |
1da177e4 | 62 | /* Select the chip by setting nCE to low */ |
7abd3ef9 | 63 | #define NAND_NCE 0x01 |
1da177e4 | 64 | /* Select the command latch by setting CLE to high */ |
7abd3ef9 | 65 | #define NAND_CLE 0x02 |
1da177e4 | 66 | /* Select the address latch by setting ALE to high */ |
7abd3ef9 TG |
67 | #define NAND_ALE 0x04 |
68 | ||
69 | #define NAND_CTRL_CLE (NAND_NCE | NAND_CLE) | |
70 | #define NAND_CTRL_ALE (NAND_NCE | NAND_ALE) | |
71 | #define NAND_CTRL_CHANGE 0x80 | |
1da177e4 LT |
72 | |
73 | /* | |
74 | * Standard NAND flash commands | |
75 | */ | |
76 | #define NAND_CMD_READ0 0 | |
77 | #define NAND_CMD_READ1 1 | |
7bc3312b | 78 | #define NAND_CMD_RNDOUT 5 |
1da177e4 LT |
79 | #define NAND_CMD_PAGEPROG 0x10 |
80 | #define NAND_CMD_READOOB 0x50 | |
81 | #define NAND_CMD_ERASE1 0x60 | |
82 | #define NAND_CMD_STATUS 0x70 | |
1da177e4 | 83 | #define NAND_CMD_SEQIN 0x80 |
7bc3312b | 84 | #define NAND_CMD_RNDIN 0x85 |
1da177e4 LT |
85 | #define NAND_CMD_READID 0x90 |
86 | #define NAND_CMD_ERASE2 0xd0 | |
caa4b6f2 | 87 | #define NAND_CMD_PARAM 0xec |
7db03ecc HS |
88 | #define NAND_CMD_GET_FEATURES 0xee |
89 | #define NAND_CMD_SET_FEATURES 0xef | |
1da177e4 LT |
90 | #define NAND_CMD_RESET 0xff |
91 | ||
7d70f334 VS |
92 | #define NAND_CMD_LOCK 0x2a |
93 | #define NAND_CMD_UNLOCK1 0x23 | |
94 | #define NAND_CMD_UNLOCK2 0x24 | |
95 | ||
1da177e4 LT |
96 | /* Extended commands for large page devices */ |
97 | #define NAND_CMD_READSTART 0x30 | |
7bc3312b | 98 | #define NAND_CMD_RNDOUTSTART 0xE0 |
1da177e4 LT |
99 | #define NAND_CMD_CACHEDPROG 0x15 |
100 | ||
7abd3ef9 TG |
101 | #define NAND_CMD_NONE -1 |
102 | ||
1da177e4 LT |
103 | /* Status bits */ |
104 | #define NAND_STATUS_FAIL 0x01 | |
105 | #define NAND_STATUS_FAIL_N1 0x02 | |
106 | #define NAND_STATUS_TRUE_READY 0x20 | |
107 | #define NAND_STATUS_READY 0x40 | |
108 | #define NAND_STATUS_WP 0x80 | |
109 | ||
61ecfa87 | 110 | /* |
1da177e4 LT |
111 | * Constants for ECC_MODES |
112 | */ | |
6dfc6d25 TG |
113 | typedef enum { |
114 | NAND_ECC_NONE, | |
115 | NAND_ECC_SOFT, | |
116 | NAND_ECC_HW, | |
117 | NAND_ECC_HW_SYNDROME, | |
6e0cb135 | 118 | NAND_ECC_HW_OOB_FIRST, |
193bd400 | 119 | NAND_ECC_SOFT_BCH, |
6dfc6d25 | 120 | } nand_ecc_modes_t; |
1da177e4 LT |
121 | |
122 | /* | |
123 | * Constants for Hardware ECC | |
068e3c0a | 124 | */ |
1da177e4 LT |
125 | /* Reset Hardware ECC for read */ |
126 | #define NAND_ECC_READ 0 | |
127 | /* Reset Hardware ECC for write */ | |
128 | #define NAND_ECC_WRITE 1 | |
7854d3f7 | 129 | /* Enable Hardware ECC before syndrome is read back from flash */ |
1da177e4 LT |
130 | #define NAND_ECC_READSYN 2 |
131 | ||
40cbe6ee BB |
132 | /* |
133 | * Enable generic NAND 'page erased' check. This check is only done when | |
134 | * ecc.correct() returns -EBADMSG. | |
135 | * Set this flag if your implementation does not fix bitflips in erased | |
136 | * pages and you want to rely on the default implementation. | |
137 | */ | |
138 | #define NAND_ECC_GENERIC_ERASED_CHECK BIT(0) | |
139 | ||
068e3c0a DM |
140 | /* Bit mask for flags passed to do_nand_read_ecc */ |
141 | #define NAND_GET_DEVICE 0x80 | |
142 | ||
143 | ||
a0491fc4 SAS |
144 | /* |
145 | * Option constants for bizarre disfunctionality and real | |
146 | * features. | |
147 | */ | |
7854d3f7 | 148 | /* Buswidth is 16 bit */ |
1da177e4 | 149 | #define NAND_BUSWIDTH_16 0x00000002 |
1da177e4 LT |
150 | /* Chip has cache program function */ |
151 | #define NAND_CACHEPRG 0x00000008 | |
5bc7c33c BN |
152 | /* |
153 | * Chip requires ready check on read (for auto-incremented sequential read). | |
154 | * True only for small page devices; large page devices do not support | |
155 | * autoincrement. | |
156 | */ | |
157 | #define NAND_NEED_READRDY 0x00000100 | |
158 | ||
29072b96 TG |
159 | /* Chip does not allow subpage writes */ |
160 | #define NAND_NO_SUBPAGE_WRITE 0x00000200 | |
161 | ||
93edbad6 ML |
162 | /* Device is one of 'new' xD cards that expose fake nand command set */ |
163 | #define NAND_BROKEN_XD 0x00000400 | |
164 | ||
165 | /* Device behaves just like nand, but is readonly */ | |
166 | #define NAND_ROM 0x00000800 | |
167 | ||
a5ff4f10 JW |
168 | /* Device supports subpage reads */ |
169 | #define NAND_SUBPAGE_READ 0x00001000 | |
170 | ||
c03d9969 BB |
171 | /* |
172 | * Some MLC NANDs need data scrambling to limit bitflips caused by repeated | |
173 | * patterns. | |
174 | */ | |
175 | #define NAND_NEED_SCRAMBLING 0x00002000 | |
176 | ||
1da177e4 | 177 | /* Options valid for Samsung large page devices */ |
3239a6cd | 178 | #define NAND_SAMSUNG_LP_OPTIONS NAND_CACHEPRG |
1da177e4 LT |
179 | |
180 | /* Macros to identify the above */ | |
1da177e4 | 181 | #define NAND_HAS_CACHEPROG(chip) ((chip->options & NAND_CACHEPRG)) |
a5ff4f10 | 182 | #define NAND_HAS_SUBPAGE_READ(chip) ((chip->options & NAND_SUBPAGE_READ)) |
1da177e4 | 183 | |
1da177e4 | 184 | /* Non chip related options */ |
0040bf38 | 185 | /* This option skips the bbt scan during initialization. */ |
b4dc53e1 | 186 | #define NAND_SKIP_BBTSCAN 0x00010000 |
a0491fc4 SAS |
187 | /* |
188 | * This option is defined if the board driver allocates its own buffers | |
189 | * (e.g. because it needs them DMA-coherent). | |
190 | */ | |
b4dc53e1 | 191 | #define NAND_OWN_BUFFERS 0x00020000 |
b1c6e6db | 192 | /* Chip may not exist, so silence any errors in scan */ |
b4dc53e1 | 193 | #define NAND_SCAN_SILENT_NODEV 0x00040000 |
64b37b2a MC |
194 | /* |
195 | * Autodetect nand buswidth with readid/onfi. | |
196 | * This suppose the driver will configure the hardware in 8 bits mode | |
197 | * when calling nand_scan_ident, and update its configuration | |
198 | * before calling nand_scan_tail. | |
199 | */ | |
200 | #define NAND_BUSWIDTH_AUTO 0x00080000 | |
5f867db6 SW |
201 | /* |
202 | * This option could be defined by controller drivers to protect against | |
203 | * kmap'ed, vmalloc'ed highmem buffers being passed from upper layers | |
204 | */ | |
205 | #define NAND_USE_BOUNCE_BUFFER 0x00100000 | |
b1c6e6db | 206 | |
1da177e4 | 207 | /* Options set by nand scan */ |
a36ed299 | 208 | /* Nand scan has allocated controller struct */ |
f75e5097 | 209 | #define NAND_CONTROLLER_ALLOC 0x80000000 |
1da177e4 | 210 | |
29072b96 TG |
211 | /* Cell info constants */ |
212 | #define NAND_CI_CHIPNR_MSK 0x03 | |
213 | #define NAND_CI_CELLTYPE_MSK 0x0C | |
7db906b7 | 214 | #define NAND_CI_CELLTYPE_SHIFT 2 |
1da177e4 | 215 | |
1da177e4 LT |
216 | /* Keep gcc happy */ |
217 | struct nand_chip; | |
218 | ||
5b40db68 HS |
219 | /* ONFI features */ |
220 | #define ONFI_FEATURE_16_BIT_BUS (1 << 0) | |
221 | #define ONFI_FEATURE_EXT_PARAM_PAGE (1 << 7) | |
222 | ||
3e70192c HS |
223 | /* ONFI timing mode, used in both asynchronous and synchronous mode */ |
224 | #define ONFI_TIMING_MODE_0 (1 << 0) | |
225 | #define ONFI_TIMING_MODE_1 (1 << 1) | |
226 | #define ONFI_TIMING_MODE_2 (1 << 2) | |
227 | #define ONFI_TIMING_MODE_3 (1 << 3) | |
228 | #define ONFI_TIMING_MODE_4 (1 << 4) | |
229 | #define ONFI_TIMING_MODE_5 (1 << 5) | |
230 | #define ONFI_TIMING_MODE_UNKNOWN (1 << 6) | |
231 | ||
7db03ecc HS |
232 | /* ONFI feature address */ |
233 | #define ONFI_FEATURE_ADDR_TIMING_MODE 0x1 | |
234 | ||
8429bb39 BN |
235 | /* Vendor-specific feature address (Micron) */ |
236 | #define ONFI_FEATURE_ADDR_READ_RETRY 0x89 | |
237 | ||
7db03ecc HS |
238 | /* ONFI subfeature parameters length */ |
239 | #define ONFI_SUBFEATURE_PARAM_LEN 4 | |
240 | ||
d914c932 DM |
241 | /* ONFI optional commands SET/GET FEATURES supported? */ |
242 | #define ONFI_OPT_CMD_SET_GET_FEATURES (1 << 2) | |
243 | ||
d1e1f4e4 FF |
244 | struct nand_onfi_params { |
245 | /* rev info and features block */ | |
b46daf7e SAS |
246 | /* 'O' 'N' 'F' 'I' */ |
247 | u8 sig[4]; | |
248 | __le16 revision; | |
249 | __le16 features; | |
250 | __le16 opt_cmd; | |
5138a98f HS |
251 | u8 reserved0[2]; |
252 | __le16 ext_param_page_length; /* since ONFI 2.1 */ | |
253 | u8 num_of_param_pages; /* since ONFI 2.1 */ | |
254 | u8 reserved1[17]; | |
d1e1f4e4 FF |
255 | |
256 | /* manufacturer information block */ | |
b46daf7e SAS |
257 | char manufacturer[12]; |
258 | char model[20]; | |
259 | u8 jedec_id; | |
260 | __le16 date_code; | |
261 | u8 reserved2[13]; | |
d1e1f4e4 FF |
262 | |
263 | /* memory organization block */ | |
b46daf7e SAS |
264 | __le32 byte_per_page; |
265 | __le16 spare_bytes_per_page; | |
266 | __le32 data_bytes_per_ppage; | |
267 | __le16 spare_bytes_per_ppage; | |
268 | __le32 pages_per_block; | |
269 | __le32 blocks_per_lun; | |
270 | u8 lun_count; | |
271 | u8 addr_cycles; | |
272 | u8 bits_per_cell; | |
273 | __le16 bb_per_lun; | |
274 | __le16 block_endurance; | |
275 | u8 guaranteed_good_blocks; | |
276 | __le16 guaranteed_block_endurance; | |
277 | u8 programs_per_page; | |
278 | u8 ppage_attr; | |
279 | u8 ecc_bits; | |
280 | u8 interleaved_bits; | |
281 | u8 interleaved_ops; | |
282 | u8 reserved3[13]; | |
d1e1f4e4 FF |
283 | |
284 | /* electrical parameter block */ | |
b46daf7e SAS |
285 | u8 io_pin_capacitance_max; |
286 | __le16 async_timing_mode; | |
287 | __le16 program_cache_timing_mode; | |
288 | __le16 t_prog; | |
289 | __le16 t_bers; | |
290 | __le16 t_r; | |
291 | __le16 t_ccs; | |
292 | __le16 src_sync_timing_mode; | |
de64aa9e | 293 | u8 src_ssync_features; |
b46daf7e SAS |
294 | __le16 clk_pin_capacitance_typ; |
295 | __le16 io_pin_capacitance_typ; | |
296 | __le16 input_pin_capacitance_typ; | |
297 | u8 input_pin_capacitance_max; | |
a55e85ce | 298 | u8 driver_strength_support; |
b46daf7e | 299 | __le16 t_int_r; |
74e98be4 | 300 | __le16 t_adl; |
de64aa9e | 301 | u8 reserved4[8]; |
d1e1f4e4 FF |
302 | |
303 | /* vendor */ | |
6f0065b0 BN |
304 | __le16 vendor_revision; |
305 | u8 vendor[88]; | |
d1e1f4e4 FF |
306 | |
307 | __le16 crc; | |
e2e6b7b7 | 308 | } __packed; |
d1e1f4e4 FF |
309 | |
310 | #define ONFI_CRC_BASE 0x4F4E | |
311 | ||
5138a98f HS |
312 | /* Extended ECC information Block Definition (since ONFI 2.1) */ |
313 | struct onfi_ext_ecc_info { | |
314 | u8 ecc_bits; | |
315 | u8 codeword_size; | |
316 | __le16 bb_per_lun; | |
317 | __le16 block_endurance; | |
318 | u8 reserved[2]; | |
319 | } __packed; | |
320 | ||
321 | #define ONFI_SECTION_TYPE_0 0 /* Unused section. */ | |
322 | #define ONFI_SECTION_TYPE_1 1 /* for additional sections. */ | |
323 | #define ONFI_SECTION_TYPE_2 2 /* for ECC information. */ | |
324 | struct onfi_ext_section { | |
325 | u8 type; | |
326 | u8 length; | |
327 | } __packed; | |
328 | ||
329 | #define ONFI_EXT_SECTION_MAX 8 | |
330 | ||
331 | /* Extended Parameter Page Definition (since ONFI 2.1) */ | |
332 | struct onfi_ext_param_page { | |
333 | __le16 crc; | |
334 | u8 sig[4]; /* 'E' 'P' 'P' 'S' */ | |
335 | u8 reserved0[10]; | |
336 | struct onfi_ext_section sections[ONFI_EXT_SECTION_MAX]; | |
337 | ||
338 | /* | |
339 | * The actual size of the Extended Parameter Page is in | |
340 | * @ext_param_page_length of nand_onfi_params{}. | |
341 | * The following are the variable length sections. | |
342 | * So we do not add any fields below. Please see the ONFI spec. | |
343 | */ | |
344 | } __packed; | |
345 | ||
6f0065b0 BN |
346 | struct nand_onfi_vendor_micron { |
347 | u8 two_plane_read; | |
348 | u8 read_cache; | |
349 | u8 read_unique_id; | |
350 | u8 dq_imped; | |
351 | u8 dq_imped_num_settings; | |
352 | u8 dq_imped_feat_addr; | |
353 | u8 rb_pulldown_strength; | |
354 | u8 rb_pulldown_strength_feat_addr; | |
355 | u8 rb_pulldown_strength_num_settings; | |
356 | u8 otp_mode; | |
357 | u8 otp_page_start; | |
358 | u8 otp_data_prot_addr; | |
359 | u8 otp_num_pages; | |
360 | u8 otp_feat_addr; | |
361 | u8 read_retry_options; | |
362 | u8 reserved[72]; | |
363 | u8 param_revision; | |
364 | } __packed; | |
365 | ||
afbfff03 HS |
366 | struct jedec_ecc_info { |
367 | u8 ecc_bits; | |
368 | u8 codeword_size; | |
369 | __le16 bb_per_lun; | |
370 | __le16 block_endurance; | |
371 | u8 reserved[2]; | |
372 | } __packed; | |
373 | ||
7852f896 HS |
374 | /* JEDEC features */ |
375 | #define JEDEC_FEATURE_16_BIT_BUS (1 << 0) | |
376 | ||
afbfff03 HS |
377 | struct nand_jedec_params { |
378 | /* rev info and features block */ | |
379 | /* 'J' 'E' 'S' 'D' */ | |
380 | u8 sig[4]; | |
381 | __le16 revision; | |
382 | __le16 features; | |
383 | u8 opt_cmd[3]; | |
384 | __le16 sec_cmd; | |
385 | u8 num_of_param_pages; | |
386 | u8 reserved0[18]; | |
387 | ||
388 | /* manufacturer information block */ | |
389 | char manufacturer[12]; | |
390 | char model[20]; | |
391 | u8 jedec_id[6]; | |
392 | u8 reserved1[10]; | |
393 | ||
394 | /* memory organization block */ | |
395 | __le32 byte_per_page; | |
396 | __le16 spare_bytes_per_page; | |
397 | u8 reserved2[6]; | |
398 | __le32 pages_per_block; | |
399 | __le32 blocks_per_lun; | |
400 | u8 lun_count; | |
401 | u8 addr_cycles; | |
402 | u8 bits_per_cell; | |
403 | u8 programs_per_page; | |
404 | u8 multi_plane_addr; | |
405 | u8 multi_plane_op_attr; | |
406 | u8 reserved3[38]; | |
407 | ||
408 | /* electrical parameter block */ | |
409 | __le16 async_sdr_speed_grade; | |
410 | __le16 toggle_ddr_speed_grade; | |
411 | __le16 sync_ddr_speed_grade; | |
412 | u8 async_sdr_features; | |
413 | u8 toggle_ddr_features; | |
414 | u8 sync_ddr_features; | |
415 | __le16 t_prog; | |
416 | __le16 t_bers; | |
417 | __le16 t_r; | |
418 | __le16 t_r_multi_plane; | |
419 | __le16 t_ccs; | |
420 | __le16 io_pin_capacitance_typ; | |
421 | __le16 input_pin_capacitance_typ; | |
422 | __le16 clk_pin_capacitance_typ; | |
423 | u8 driver_strength_support; | |
74e98be4 | 424 | __le16 t_adl; |
afbfff03 HS |
425 | u8 reserved4[36]; |
426 | ||
427 | /* ECC and endurance block */ | |
428 | u8 guaranteed_good_blocks; | |
429 | __le16 guaranteed_block_endurance; | |
430 | struct jedec_ecc_info ecc_info[4]; | |
431 | u8 reserved5[29]; | |
432 | ||
433 | /* reserved */ | |
434 | u8 reserved6[148]; | |
435 | ||
436 | /* vendor */ | |
437 | __le16 vendor_rev_num; | |
438 | u8 reserved7[88]; | |
439 | ||
440 | /* CRC for Parameter Page */ | |
441 | __le16 crc; | |
442 | } __packed; | |
443 | ||
1da177e4 | 444 | /** |
844d3b42 | 445 | * struct nand_hw_control - Control structure for hardware controller (e.g ECC generator) shared among independent devices |
61ecfa87 | 446 | * @lock: protection lock |
1da177e4 | 447 | * @active: the mtd device which holds the controller currently |
a0491fc4 SAS |
448 | * @wq: wait queue to sleep on if a NAND operation is in |
449 | * progress used instead of the per chip wait queue | |
450 | * when a hw controller is available. | |
1da177e4 LT |
451 | */ |
452 | struct nand_hw_control { | |
b46daf7e | 453 | spinlock_t lock; |
1da177e4 | 454 | struct nand_chip *active; |
0dfc6246 | 455 | wait_queue_head_t wq; |
1da177e4 LT |
456 | }; |
457 | ||
6dfc6d25 | 458 | /** |
7854d3f7 BN |
459 | * struct nand_ecc_ctrl - Control structure for ECC |
460 | * @mode: ECC mode | |
461 | * @steps: number of ECC steps per page | |
462 | * @size: data bytes per ECC step | |
463 | * @bytes: ECC bytes per step | |
1d0b95b0 | 464 | * @strength: max number of correctible bits per ECC step |
7854d3f7 BN |
465 | * @total: total number of ECC bytes per page |
466 | * @prepad: padding information for syndrome based ECC generators | |
467 | * @postpad: padding information for syndrome based ECC generators | |
40cbe6ee | 468 | * @options: ECC specific options (see NAND_ECC_XXX flags defined above) |
844d3b42 | 469 | * @layout: ECC layout control struct pointer |
7854d3f7 BN |
470 | * @priv: pointer to private ECC control data |
471 | * @hwctl: function to control hardware ECC generator. Must only | |
6dfc6d25 | 472 | * be provided if an hardware ECC is available |
7854d3f7 | 473 | * @calculate: function for ECC calculation or readback from ECC hardware |
6e941192 BB |
474 | * @correct: function for ECC correction, matching to ECC generator (sw/hw). |
475 | * Should return a positive number representing the number of | |
476 | * corrected bitflips, -EBADMSG if the number of bitflips exceed | |
477 | * ECC strength, or any other error code if the error is not | |
478 | * directly related to correction. | |
479 | * If -EBADMSG is returned the input buffers should be left | |
480 | * untouched. | |
62d956dc BB |
481 | * @read_page_raw: function to read a raw page without ECC. This function |
482 | * should hide the specific layout used by the ECC | |
483 | * controller and always return contiguous in-band and | |
484 | * out-of-band data even if they're not stored | |
485 | * contiguously on the NAND chip (e.g. | |
486 | * NAND_ECC_HW_SYNDROME interleaves in-band and | |
487 | * out-of-band data). | |
488 | * @write_page_raw: function to write a raw page without ECC. This function | |
489 | * should hide the specific layout used by the ECC | |
490 | * controller and consider the passed data as contiguous | |
491 | * in-band and out-of-band data. ECC controller is | |
492 | * responsible for doing the appropriate transformations | |
493 | * to adapt to its specific layout (e.g. | |
494 | * NAND_ECC_HW_SYNDROME interleaves in-band and | |
495 | * out-of-band data). | |
7854d3f7 | 496 | * @read_page: function to read a page according to the ECC generator |
5ca7f415 MD |
497 | * requirements; returns maximum number of bitflips corrected in |
498 | * any single ECC step, 0 if bitflips uncorrectable, -EIO hw error | |
499 | * @read_subpage: function to read parts of the page covered by ECC; | |
500 | * returns same as read_page() | |
837a6ba4 | 501 | * @write_subpage: function to write parts of the page covered by ECC. |
7854d3f7 | 502 | * @write_page: function to write a page according to the ECC generator |
a0491fc4 | 503 | * requirements. |
9ce244b3 | 504 | * @write_oob_raw: function to write chip OOB data without ECC |
c46f6483 | 505 | * @read_oob_raw: function to read chip OOB data without ECC |
844d3b42 RD |
506 | * @read_oob: function to read chip OOB data |
507 | * @write_oob: function to write chip OOB data | |
6dfc6d25 TG |
508 | */ |
509 | struct nand_ecc_ctrl { | |
b46daf7e SAS |
510 | nand_ecc_modes_t mode; |
511 | int steps; | |
512 | int size; | |
513 | int bytes; | |
514 | int total; | |
1d0b95b0 | 515 | int strength; |
b46daf7e SAS |
516 | int prepad; |
517 | int postpad; | |
40cbe6ee | 518 | unsigned int options; |
5bd34c09 | 519 | struct nand_ecclayout *layout; |
193bd400 | 520 | void *priv; |
b46daf7e SAS |
521 | void (*hwctl)(struct mtd_info *mtd, int mode); |
522 | int (*calculate)(struct mtd_info *mtd, const uint8_t *dat, | |
523 | uint8_t *ecc_code); | |
524 | int (*correct)(struct mtd_info *mtd, uint8_t *dat, uint8_t *read_ecc, | |
525 | uint8_t *calc_ecc); | |
526 | int (*read_page_raw)(struct mtd_info *mtd, struct nand_chip *chip, | |
1fbb938d | 527 | uint8_t *buf, int oob_required, int page); |
fdbad98d | 528 | int (*write_page_raw)(struct mtd_info *mtd, struct nand_chip *chip, |
45aaeff9 | 529 | const uint8_t *buf, int oob_required, int page); |
b46daf7e | 530 | int (*read_page)(struct mtd_info *mtd, struct nand_chip *chip, |
1fbb938d | 531 | uint8_t *buf, int oob_required, int page); |
b46daf7e | 532 | int (*read_subpage)(struct mtd_info *mtd, struct nand_chip *chip, |
e004debd | 533 | uint32_t offs, uint32_t len, uint8_t *buf, int page); |
837a6ba4 GP |
534 | int (*write_subpage)(struct mtd_info *mtd, struct nand_chip *chip, |
535 | uint32_t offset, uint32_t data_len, | |
45aaeff9 | 536 | const uint8_t *data_buf, int oob_required, int page); |
fdbad98d | 537 | int (*write_page)(struct mtd_info *mtd, struct nand_chip *chip, |
45aaeff9 | 538 | const uint8_t *buf, int oob_required, int page); |
9ce244b3 BN |
539 | int (*write_oob_raw)(struct mtd_info *mtd, struct nand_chip *chip, |
540 | int page); | |
c46f6483 | 541 | int (*read_oob_raw)(struct mtd_info *mtd, struct nand_chip *chip, |
5c2ffb11 SL |
542 | int page); |
543 | int (*read_oob)(struct mtd_info *mtd, struct nand_chip *chip, int page); | |
b46daf7e SAS |
544 | int (*write_oob)(struct mtd_info *mtd, struct nand_chip *chip, |
545 | int page); | |
f75e5097 TG |
546 | }; |
547 | ||
548 | /** | |
549 | * struct nand_buffers - buffer structure for read/write | |
f02ea4e6 HS |
550 | * @ecccalc: buffer pointer for calculated ECC, size is oobsize. |
551 | * @ecccode: buffer pointer for ECC read from flash, size is oobsize. | |
552 | * @databuf: buffer pointer for data, size is (page size + oobsize). | |
f75e5097 TG |
553 | * |
554 | * Do not change the order of buffers. databuf and oobrbuf must be in | |
555 | * consecutive order. | |
556 | */ | |
557 | struct nand_buffers { | |
f02ea4e6 HS |
558 | uint8_t *ecccalc; |
559 | uint8_t *ecccode; | |
560 | uint8_t *databuf; | |
6dfc6d25 TG |
561 | }; |
562 | ||
1da177e4 LT |
563 | /** |
564 | * struct nand_chip - NAND Private Flash Chip Data | |
ed4f85c0 | 565 | * @mtd: MTD device registered to the MTD framework |
a0491fc4 SAS |
566 | * @IO_ADDR_R: [BOARDSPECIFIC] address to read the 8 I/O lines of the |
567 | * flash device | |
568 | * @IO_ADDR_W: [BOARDSPECIFIC] address to write the 8 I/O lines of the | |
569 | * flash device. | |
1da177e4 | 570 | * @read_byte: [REPLACEABLE] read one byte from the chip |
1da177e4 | 571 | * @read_word: [REPLACEABLE] read one word from the chip |
05f78359 UKK |
572 | * @write_byte: [REPLACEABLE] write a single byte to the chip on the |
573 | * low 8 I/O lines | |
1da177e4 LT |
574 | * @write_buf: [REPLACEABLE] write data from the buffer to the chip |
575 | * @read_buf: [REPLACEABLE] read data from the chip into the buffer | |
1da177e4 | 576 | * @select_chip: [REPLACEABLE] select chip nr |
ce157510 BN |
577 | * @block_bad: [REPLACEABLE] check if a block is bad, using OOB markers |
578 | * @block_markbad: [REPLACEABLE] mark a block bad | |
25985edc | 579 | * @cmd_ctrl: [BOARDSPECIFIC] hardwarespecific function for controlling |
7abd3ef9 | 580 | * ALE/CLE/nCE. Also used to write command and address |
7854d3f7 | 581 | * @dev_ready: [BOARDSPECIFIC] hardwarespecific function for accessing |
a0491fc4 SAS |
582 | * device ready/busy line. If set to NULL no access to |
583 | * ready/busy is available and the ready/busy information | |
584 | * is read from the chip status register. | |
585 | * @cmdfunc: [REPLACEABLE] hardwarespecific function for writing | |
586 | * commands to the chip. | |
587 | * @waitfunc: [REPLACEABLE] hardwarespecific function for wait on | |
588 | * ready. | |
ba84fb59 BN |
589 | * @setup_read_retry: [FLASHSPECIFIC] flash (vendor) specific function for |
590 | * setting the read-retry mode. Mostly needed for MLC NAND. | |
7854d3f7 | 591 | * @ecc: [BOARDSPECIFIC] ECC control structure |
844d3b42 RD |
592 | * @buffers: buffer structure for read/write |
593 | * @hwcontrol: platform-specific hardware control structure | |
49c50b97 | 594 | * @erase: [REPLACEABLE] erase function |
1da177e4 | 595 | * @scan_bbt: [REPLACEABLE] function to scan bad block table |
25985edc | 596 | * @chip_delay: [BOARDSPECIFIC] chip dependent delay for transferring |
a0491fc4 | 597 | * data from array to read regs (tR). |
2c0a2bed | 598 | * @state: [INTERN] the current state of the NAND device |
e9195edc BN |
599 | * @oob_poi: "poison value buffer," used for laying out OOB data |
600 | * before writing | |
a0491fc4 SAS |
601 | * @page_shift: [INTERN] number of address bits in a page (column |
602 | * address bits). | |
1da177e4 LT |
603 | * @phys_erase_shift: [INTERN] number of address bits in a physical eraseblock |
604 | * @bbt_erase_shift: [INTERN] number of address bits in a bbt entry | |
605 | * @chip_shift: [INTERN] number of address bits in one chip | |
a0491fc4 SAS |
606 | * @options: [BOARDSPECIFIC] various chip options. They can partly |
607 | * be set to inform nand_scan about special functionality. | |
608 | * See the defines for further explanation. | |
5fb1549d BN |
609 | * @bbt_options: [INTERN] bad block specific options. All options used |
610 | * here must come from bbm.h. By default, these options | |
611 | * will be copied to the appropriate nand_bbt_descr's. | |
a0491fc4 SAS |
612 | * @badblockpos: [INTERN] position of the bad block marker in the oob |
613 | * area. | |
661a0832 BN |
614 | * @badblockbits: [INTERN] minimum number of set bits in a good block's |
615 | * bad block marker position; i.e., BBM == 11110111b is | |
616 | * not bad when badblockbits == 7 | |
7db906b7 | 617 | * @bits_per_cell: [INTERN] number of bits per cell. i.e., 1 means SLC. |
4cfeca2d HS |
618 | * @ecc_strength_ds: [INTERN] ECC correctability from the datasheet. |
619 | * Minimum amount of bit errors per @ecc_step_ds guaranteed | |
620 | * to be correctable. If unknown, set to zero. | |
621 | * @ecc_step_ds: [INTERN] ECC step required by the @ecc_strength_ds, | |
622 | * also from the datasheet. It is the recommended ECC step | |
623 | * size, if known; if unknown, set to zero. | |
57a94e24 BB |
624 | * @onfi_timing_mode_default: [INTERN] default ONFI timing mode. This field is |
625 | * either deduced from the datasheet if the NAND | |
626 | * chip is not ONFI compliant or set to 0 if it is | |
627 | * (an ONFI chip is always configured in mode 0 | |
628 | * after a NAND reset) | |
1da177e4 LT |
629 | * @numchips: [INTERN] number of physical chips |
630 | * @chipsize: [INTERN] the size of one chip for multichip arrays | |
631 | * @pagemask: [INTERN] page number mask = number of (pages / chip) - 1 | |
a0491fc4 SAS |
632 | * @pagebuf: [INTERN] holds the pagenumber which is currently in |
633 | * data_buf. | |
edbc4540 MD |
634 | * @pagebuf_bitflips: [INTERN] holds the bitflip count for the page which is |
635 | * currently in data_buf. | |
29072b96 | 636 | * @subpagesize: [INTERN] holds the subpagesize |
a0491fc4 SAS |
637 | * @onfi_version: [INTERN] holds the chip ONFI version (BCD encoded), |
638 | * non 0 if ONFI supported. | |
d94abba7 HS |
639 | * @jedec_version: [INTERN] holds the chip JEDEC version (BCD encoded), |
640 | * non 0 if JEDEC supported. | |
a0491fc4 SAS |
641 | * @onfi_params: [INTERN] holds the ONFI page parameter when ONFI is |
642 | * supported, 0 otherwise. | |
d94abba7 HS |
643 | * @jedec_params: [INTERN] holds the JEDEC parameter page when JEDEC is |
644 | * supported, 0 otherwise. | |
ba84fb59 | 645 | * @read_retries: [INTERN] the number of read retry modes supported |
9ef525a9 RD |
646 | * @onfi_set_features: [REPLACEABLE] set the features for ONFI nand |
647 | * @onfi_get_features: [REPLACEABLE] get the features for ONFI nand | |
1da177e4 | 648 | * @bbt: [INTERN] bad block table pointer |
a0491fc4 SAS |
649 | * @bbt_td: [REPLACEABLE] bad block table descriptor for flash |
650 | * lookup. | |
1da177e4 | 651 | * @bbt_md: [REPLACEABLE] bad block table mirror descriptor |
a0491fc4 SAS |
652 | * @badblock_pattern: [REPLACEABLE] bad block scan pattern used for initial |
653 | * bad block scan. | |
654 | * @controller: [REPLACEABLE] a pointer to a hardware controller | |
7854d3f7 | 655 | * structure which is shared among multiple independent |
a0491fc4 | 656 | * devices. |
32c8db8f | 657 | * @priv: [OPTIONAL] pointer to private chip data |
a0491fc4 SAS |
658 | * @errstat: [OPTIONAL] hardware specific function to perform |
659 | * additional error status checks (determine if errors are | |
660 | * correctable). | |
351edd24 | 661 | * @write_page: [REPLACEABLE] High-level page write function |
1da177e4 | 662 | */ |
61ecfa87 | 663 | |
1da177e4 | 664 | struct nand_chip { |
ed4f85c0 | 665 | struct mtd_info mtd; |
b46daf7e SAS |
666 | void __iomem *IO_ADDR_R; |
667 | void __iomem *IO_ADDR_W; | |
668 | ||
669 | uint8_t (*read_byte)(struct mtd_info *mtd); | |
670 | u16 (*read_word)(struct mtd_info *mtd); | |
05f78359 | 671 | void (*write_byte)(struct mtd_info *mtd, uint8_t byte); |
b46daf7e SAS |
672 | void (*write_buf)(struct mtd_info *mtd, const uint8_t *buf, int len); |
673 | void (*read_buf)(struct mtd_info *mtd, uint8_t *buf, int len); | |
b46daf7e SAS |
674 | void (*select_chip)(struct mtd_info *mtd, int chip); |
675 | int (*block_bad)(struct mtd_info *mtd, loff_t ofs, int getchip); | |
676 | int (*block_markbad)(struct mtd_info *mtd, loff_t ofs); | |
677 | void (*cmd_ctrl)(struct mtd_info *mtd, int dat, unsigned int ctrl); | |
b46daf7e SAS |
678 | int (*dev_ready)(struct mtd_info *mtd); |
679 | void (*cmdfunc)(struct mtd_info *mtd, unsigned command, int column, | |
680 | int page_addr); | |
681 | int(*waitfunc)(struct mtd_info *mtd, struct nand_chip *this); | |
49c50b97 | 682 | int (*erase)(struct mtd_info *mtd, int page); |
b46daf7e SAS |
683 | int (*scan_bbt)(struct mtd_info *mtd); |
684 | int (*errstat)(struct mtd_info *mtd, struct nand_chip *this, int state, | |
685 | int status, int page); | |
686 | int (*write_page)(struct mtd_info *mtd, struct nand_chip *chip, | |
837a6ba4 GP |
687 | uint32_t offset, int data_len, const uint8_t *buf, |
688 | int oob_required, int page, int cached, int raw); | |
7db03ecc HS |
689 | int (*onfi_set_features)(struct mtd_info *mtd, struct nand_chip *chip, |
690 | int feature_addr, uint8_t *subfeature_para); | |
691 | int (*onfi_get_features)(struct mtd_info *mtd, struct nand_chip *chip, | |
692 | int feature_addr, uint8_t *subfeature_para); | |
ba84fb59 | 693 | int (*setup_read_retry)(struct mtd_info *mtd, int retry_mode); |
b46daf7e SAS |
694 | |
695 | int chip_delay; | |
696 | unsigned int options; | |
5fb1549d | 697 | unsigned int bbt_options; |
b46daf7e SAS |
698 | |
699 | int page_shift; | |
700 | int phys_erase_shift; | |
701 | int bbt_erase_shift; | |
702 | int chip_shift; | |
703 | int numchips; | |
704 | uint64_t chipsize; | |
705 | int pagemask; | |
706 | int pagebuf; | |
edbc4540 | 707 | unsigned int pagebuf_bitflips; |
b46daf7e | 708 | int subpagesize; |
7db906b7 | 709 | uint8_t bits_per_cell; |
4cfeca2d HS |
710 | uint16_t ecc_strength_ds; |
711 | uint16_t ecc_step_ds; | |
57a94e24 | 712 | int onfi_timing_mode_default; |
b46daf7e SAS |
713 | int badblockpos; |
714 | int badblockbits; | |
715 | ||
716 | int onfi_version; | |
d94abba7 HS |
717 | int jedec_version; |
718 | union { | |
719 | struct nand_onfi_params onfi_params; | |
720 | struct nand_jedec_params jedec_params; | |
721 | }; | |
d1e1f4e4 | 722 | |
ba84fb59 BN |
723 | int read_retries; |
724 | ||
b46daf7e | 725 | flstate_t state; |
f75e5097 | 726 | |
b46daf7e SAS |
727 | uint8_t *oob_poi; |
728 | struct nand_hw_control *controller; | |
f75e5097 TG |
729 | |
730 | struct nand_ecc_ctrl ecc; | |
4bf63fcb | 731 | struct nand_buffers *buffers; |
f75e5097 TG |
732 | struct nand_hw_control hwcontrol; |
733 | ||
b46daf7e SAS |
734 | uint8_t *bbt; |
735 | struct nand_bbt_descr *bbt_td; | |
736 | struct nand_bbt_descr *bbt_md; | |
f75e5097 | 737 | |
b46daf7e | 738 | struct nand_bbt_descr *badblock_pattern; |
f75e5097 | 739 | |
b46daf7e | 740 | void *priv; |
1da177e4 LT |
741 | }; |
742 | ||
28b8b26b BN |
743 | static inline void nand_set_flash_node(struct nand_chip *chip, |
744 | struct device_node *np) | |
745 | { | |
29574ede | 746 | mtd_set_of_node(&chip->mtd, np); |
28b8b26b BN |
747 | } |
748 | ||
749 | static inline struct device_node *nand_get_flash_node(struct nand_chip *chip) | |
750 | { | |
29574ede | 751 | return mtd_get_of_node(&chip->mtd); |
28b8b26b BN |
752 | } |
753 | ||
9eba47dd BB |
754 | static inline struct nand_chip *mtd_to_nand(struct mtd_info *mtd) |
755 | { | |
2d3b77ba | 756 | return container_of(mtd, struct nand_chip, mtd); |
9eba47dd BB |
757 | } |
758 | ||
ffd014f4 BB |
759 | static inline struct mtd_info *nand_to_mtd(struct nand_chip *chip) |
760 | { | |
761 | return &chip->mtd; | |
762 | } | |
763 | ||
d39ddbd9 BB |
764 | static inline void *nand_get_controller_data(struct nand_chip *chip) |
765 | { | |
766 | return chip->priv; | |
767 | } | |
768 | ||
769 | static inline void nand_set_controller_data(struct nand_chip *chip, void *priv) | |
770 | { | |
771 | chip->priv = priv; | |
772 | } | |
773 | ||
1da177e4 LT |
774 | /* |
775 | * NAND Flash Manufacturer ID Codes | |
776 | */ | |
777 | #define NAND_MFR_TOSHIBA 0x98 | |
778 | #define NAND_MFR_SAMSUNG 0xec | |
779 | #define NAND_MFR_FUJITSU 0x04 | |
780 | #define NAND_MFR_NATIONAL 0x8f | |
781 | #define NAND_MFR_RENESAS 0x07 | |
782 | #define NAND_MFR_STMICRO 0x20 | |
2c0a2bed | 783 | #define NAND_MFR_HYNIX 0xad |
8c60e547 | 784 | #define NAND_MFR_MICRON 0x2c |
30eb0db0 | 785 | #define NAND_MFR_AMD 0x01 |
c1257b47 | 786 | #define NAND_MFR_MACRONIX 0xc2 |
b1ccfab3 | 787 | #define NAND_MFR_EON 0x92 |
3f97c6ff | 788 | #define NAND_MFR_SANDISK 0x45 |
4968a412 | 789 | #define NAND_MFR_INTEL 0x89 |
641519cb | 790 | #define NAND_MFR_ATO 0x9b |
1da177e4 | 791 | |
53552d22 AB |
792 | /* The maximum expected count of bytes in the NAND ID sequence */ |
793 | #define NAND_MAX_ID_LEN 8 | |
794 | ||
8dbfae1e AB |
795 | /* |
796 | * A helper for defining older NAND chips where the second ID byte fully | |
797 | * defined the chip, including the geometry (chip size, eraseblock size, page | |
5bfa9b71 | 798 | * size). All these chips have 512 bytes NAND page size. |
8dbfae1e | 799 | */ |
5bfa9b71 AB |
800 | #define LEGACY_ID_NAND(nm, devid, chipsz, erasesz, opts) \ |
801 | { .name = (nm), {{ .dev_id = (devid) }}, .pagesize = 512, \ | |
802 | .chipsize = (chipsz), .erasesize = (erasesz), .options = (opts) } | |
8dbfae1e AB |
803 | |
804 | /* | |
805 | * A helper for defining newer chips which report their page size and | |
806 | * eraseblock size via the extended ID bytes. | |
807 | * | |
808 | * The real difference between LEGACY_ID_NAND and EXTENDED_ID_NAND is that with | |
809 | * EXTENDED_ID_NAND, manufacturers overloaded the same device ID so that the | |
810 | * device ID now only represented a particular total chip size (and voltage, | |
811 | * buswidth), and the page size, eraseblock size, and OOB size could vary while | |
812 | * using the same device ID. | |
813 | */ | |
8e12b474 AB |
814 | #define EXTENDED_ID_NAND(nm, devid, chipsz, opts) \ |
815 | { .name = (nm), {{ .dev_id = (devid) }}, .chipsize = (chipsz), \ | |
8dbfae1e AB |
816 | .options = (opts) } |
817 | ||
2dc0bdd9 HS |
818 | #define NAND_ECC_INFO(_strength, _step) \ |
819 | { .strength_ds = (_strength), .step_ds = (_step) } | |
820 | #define NAND_ECC_STRENGTH(type) ((type)->ecc.strength_ds) | |
821 | #define NAND_ECC_STEP(type) ((type)->ecc.step_ds) | |
822 | ||
1da177e4 LT |
823 | /** |
824 | * struct nand_flash_dev - NAND Flash Device ID Structure | |
68aa352d AB |
825 | * @name: a human-readable name of the NAND chip |
826 | * @dev_id: the device ID (the second byte of the full chip ID array) | |
8e12b474 AB |
827 | * @mfr_id: manufecturer ID part of the full chip ID array (refers the same |
828 | * memory address as @id[0]) | |
829 | * @dev_id: device ID part of the full chip ID array (refers the same memory | |
830 | * address as @id[1]) | |
831 | * @id: full device ID array | |
68aa352d AB |
832 | * @pagesize: size of the NAND page in bytes; if 0, then the real page size (as |
833 | * well as the eraseblock size) is determined from the extended NAND | |
834 | * chip ID array) | |
68aa352d | 835 | * @chipsize: total chip size in MiB |
ecb42fea | 836 | * @erasesize: eraseblock size in bytes (determined from the extended ID if 0) |
68aa352d | 837 | * @options: stores various chip bit options |
f22d5f63 HS |
838 | * @id_len: The valid length of the @id. |
839 | * @oobsize: OOB size | |
7b7d8982 | 840 | * @ecc: ECC correctability and step information from the datasheet. |
2dc0bdd9 HS |
841 | * @ecc.strength_ds: The ECC correctability from the datasheet, same as the |
842 | * @ecc_strength_ds in nand_chip{}. | |
843 | * @ecc.step_ds: The ECC step required by the @ecc.strength_ds, same as the | |
844 | * @ecc_step_ds in nand_chip{}, also from the datasheet. | |
845 | * For example, the "4bit ECC for each 512Byte" can be set with | |
846 | * NAND_ECC_INFO(4, 512). | |
57a94e24 BB |
847 | * @onfi_timing_mode_default: the default ONFI timing mode entered after a NAND |
848 | * reset. Should be deduced from timings described | |
849 | * in the datasheet. | |
850 | * | |
1da177e4 LT |
851 | */ |
852 | struct nand_flash_dev { | |
853 | char *name; | |
8e12b474 AB |
854 | union { |
855 | struct { | |
856 | uint8_t mfr_id; | |
857 | uint8_t dev_id; | |
858 | }; | |
53552d22 | 859 | uint8_t id[NAND_MAX_ID_LEN]; |
8e12b474 | 860 | }; |
ecb42fea AB |
861 | unsigned int pagesize; |
862 | unsigned int chipsize; | |
863 | unsigned int erasesize; | |
864 | unsigned int options; | |
f22d5f63 HS |
865 | uint16_t id_len; |
866 | uint16_t oobsize; | |
2dc0bdd9 HS |
867 | struct { |
868 | uint16_t strength_ds; | |
869 | uint16_t step_ds; | |
870 | } ecc; | |
57a94e24 | 871 | int onfi_timing_mode_default; |
1da177e4 LT |
872 | }; |
873 | ||
874 | /** | |
875 | * struct nand_manufacturers - NAND Flash Manufacturer ID Structure | |
876 | * @name: Manufacturer name | |
2c0a2bed | 877 | * @id: manufacturer ID code of device. |
1da177e4 LT |
878 | */ |
879 | struct nand_manufacturers { | |
880 | int id; | |
a0491fc4 | 881 | char *name; |
1da177e4 LT |
882 | }; |
883 | ||
884 | extern struct nand_flash_dev nand_flash_ids[]; | |
885 | extern struct nand_manufacturers nand_manuf_ids[]; | |
886 | ||
f5bbdacc | 887 | extern int nand_default_bbt(struct mtd_info *mtd); |
b32843b7 | 888 | extern int nand_markbad_bbt(struct mtd_info *mtd, loff_t offs); |
8471bb73 | 889 | extern int nand_isreserved_bbt(struct mtd_info *mtd, loff_t offs); |
f5bbdacc TG |
890 | extern int nand_isbad_bbt(struct mtd_info *mtd, loff_t offs, int allowbbt); |
891 | extern int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr, | |
892 | int allowbbt); | |
893 | extern int nand_do_read(struct mtd_info *mtd, loff_t from, size_t len, | |
a0491fc4 | 894 | size_t *retlen, uint8_t *buf); |
1da177e4 | 895 | |
41796c2e TG |
896 | /** |
897 | * struct platform_nand_chip - chip level device structure | |
41796c2e | 898 | * @nr_chips: max. number of chips to scan for |
844d3b42 | 899 | * @chip_offset: chip number offset |
8be834f7 | 900 | * @nr_partitions: number of partitions pointed to by partitions (or zero) |
41796c2e TG |
901 | * @partitions: mtd partition list |
902 | * @chip_delay: R/B delay value in us | |
903 | * @options: Option flags, e.g. 16bit buswidth | |
a40f7341 | 904 | * @bbt_options: BBT option flags, e.g. NAND_BBT_USE_FLASH |
972edcb7 | 905 | * @part_probe_types: NULL-terminated array of probe types |
41796c2e TG |
906 | */ |
907 | struct platform_nand_chip { | |
b46daf7e SAS |
908 | int nr_chips; |
909 | int chip_offset; | |
910 | int nr_partitions; | |
911 | struct mtd_partition *partitions; | |
b46daf7e SAS |
912 | int chip_delay; |
913 | unsigned int options; | |
a40f7341 | 914 | unsigned int bbt_options; |
b46daf7e | 915 | const char **part_probe_types; |
41796c2e TG |
916 | }; |
917 | ||
bf95efd4 HS |
918 | /* Keep gcc happy */ |
919 | struct platform_device; | |
920 | ||
41796c2e TG |
921 | /** |
922 | * struct platform_nand_ctrl - controller level device structure | |
bf95efd4 HS |
923 | * @probe: platform specific function to probe/setup hardware |
924 | * @remove: platform specific function to remove/teardown hardware | |
41796c2e TG |
925 | * @hwcontrol: platform specific hardware control structure |
926 | * @dev_ready: platform specific function to read ready/busy pin | |
927 | * @select_chip: platform specific chip select function | |
972edcb7 VW |
928 | * @cmd_ctrl: platform specific function for controlling |
929 | * ALE/CLE/nCE. Also used to write command and address | |
d6fed9e9 AC |
930 | * @write_buf: platform specific function for write buffer |
931 | * @read_buf: platform specific function for read buffer | |
25806d3c | 932 | * @read_byte: platform specific function to read one byte from chip |
844d3b42 | 933 | * @priv: private data to transport driver specific settings |
41796c2e TG |
934 | * |
935 | * All fields are optional and depend on the hardware driver requirements | |
936 | */ | |
937 | struct platform_nand_ctrl { | |
b46daf7e SAS |
938 | int (*probe)(struct platform_device *pdev); |
939 | void (*remove)(struct platform_device *pdev); | |
940 | void (*hwcontrol)(struct mtd_info *mtd, int cmd); | |
941 | int (*dev_ready)(struct mtd_info *mtd); | |
942 | void (*select_chip)(struct mtd_info *mtd, int chip); | |
943 | void (*cmd_ctrl)(struct mtd_info *mtd, int dat, unsigned int ctrl); | |
944 | void (*write_buf)(struct mtd_info *mtd, const uint8_t *buf, int len); | |
945 | void (*read_buf)(struct mtd_info *mtd, uint8_t *buf, int len); | |
b4f7aa84 | 946 | unsigned char (*read_byte)(struct mtd_info *mtd); |
b46daf7e | 947 | void *priv; |
41796c2e TG |
948 | }; |
949 | ||
972edcb7 VW |
950 | /** |
951 | * struct platform_nand_data - container structure for platform-specific data | |
952 | * @chip: chip level chip structure | |
953 | * @ctrl: controller level device structure | |
954 | */ | |
955 | struct platform_nand_data { | |
b46daf7e SAS |
956 | struct platform_nand_chip chip; |
957 | struct platform_nand_ctrl ctrl; | |
972edcb7 VW |
958 | }; |
959 | ||
5b40db68 HS |
960 | /* return the supported features. */ |
961 | static inline int onfi_feature(struct nand_chip *chip) | |
962 | { | |
963 | return chip->onfi_version ? le16_to_cpu(chip->onfi_params.features) : 0; | |
964 | } | |
965 | ||
3e70192c HS |
966 | /* return the supported asynchronous timing mode. */ |
967 | static inline int onfi_get_async_timing_mode(struct nand_chip *chip) | |
968 | { | |
969 | if (!chip->onfi_version) | |
970 | return ONFI_TIMING_MODE_UNKNOWN; | |
971 | return le16_to_cpu(chip->onfi_params.async_timing_mode); | |
972 | } | |
973 | ||
974 | /* return the supported synchronous timing mode. */ | |
975 | static inline int onfi_get_sync_timing_mode(struct nand_chip *chip) | |
976 | { | |
977 | if (!chip->onfi_version) | |
978 | return ONFI_TIMING_MODE_UNKNOWN; | |
979 | return le16_to_cpu(chip->onfi_params.src_sync_timing_mode); | |
980 | } | |
981 | ||
1d0ed69d HS |
982 | /* |
983 | * Check if it is a SLC nand. | |
984 | * The !nand_is_slc() can be used to check the MLC/TLC nand chips. | |
985 | * We do not distinguish the MLC and TLC now. | |
986 | */ | |
987 | static inline bool nand_is_slc(struct nand_chip *chip) | |
988 | { | |
7db906b7 | 989 | return chip->bits_per_cell == 1; |
1d0ed69d | 990 | } |
3dad2344 BN |
991 | |
992 | /** | |
993 | * Check if the opcode's address should be sent only on the lower 8 bits | |
994 | * @command: opcode to check | |
995 | */ | |
996 | static inline int nand_opcode_8bits(unsigned int command) | |
997 | { | |
e34fcb07 DM |
998 | switch (command) { |
999 | case NAND_CMD_READID: | |
1000 | case NAND_CMD_PARAM: | |
1001 | case NAND_CMD_GET_FEATURES: | |
1002 | case NAND_CMD_SET_FEATURES: | |
1003 | return 1; | |
1004 | default: | |
1005 | break; | |
1006 | } | |
1007 | return 0; | |
3dad2344 BN |
1008 | } |
1009 | ||
7852f896 HS |
1010 | /* return the supported JEDEC features. */ |
1011 | static inline int jedec_feature(struct nand_chip *chip) | |
1012 | { | |
1013 | return chip->jedec_version ? le16_to_cpu(chip->jedec_params.features) | |
1014 | : 0; | |
1015 | } | |
bb5fd0b6 | 1016 | |
b25046b1 | 1017 | /* |
bb5fd0b6 BB |
1018 | * struct nand_sdr_timings - SDR NAND chip timings |
1019 | * | |
1020 | * This struct defines the timing requirements of a SDR NAND chip. | |
1021 | * These informations can be found in every NAND datasheets and the timings | |
1022 | * meaning are described in the ONFI specifications: | |
1023 | * www.onfi.org/~/media/ONFI/specs/onfi_3_1_spec.pdf (chapter 4.15 Timing | |
1024 | * Parameters) | |
1025 | * | |
1026 | * All these timings are expressed in picoseconds. | |
1027 | */ | |
1028 | ||
1029 | struct nand_sdr_timings { | |
1030 | u32 tALH_min; | |
1031 | u32 tADL_min; | |
1032 | u32 tALS_min; | |
1033 | u32 tAR_min; | |
1034 | u32 tCEA_max; | |
1035 | u32 tCEH_min; | |
1036 | u32 tCH_min; | |
1037 | u32 tCHZ_max; | |
1038 | u32 tCLH_min; | |
1039 | u32 tCLR_min; | |
1040 | u32 tCLS_min; | |
1041 | u32 tCOH_min; | |
1042 | u32 tCS_min; | |
1043 | u32 tDH_min; | |
1044 | u32 tDS_min; | |
1045 | u32 tFEAT_max; | |
1046 | u32 tIR_min; | |
1047 | u32 tITC_max; | |
1048 | u32 tRC_min; | |
1049 | u32 tREA_max; | |
1050 | u32 tREH_min; | |
1051 | u32 tRHOH_min; | |
1052 | u32 tRHW_min; | |
1053 | u32 tRHZ_max; | |
1054 | u32 tRLOH_min; | |
1055 | u32 tRP_min; | |
1056 | u32 tRR_min; | |
1057 | u64 tRST_max; | |
1058 | u32 tWB_max; | |
1059 | u32 tWC_min; | |
1060 | u32 tWH_min; | |
1061 | u32 tWHR_min; | |
1062 | u32 tWP_min; | |
1063 | u32 tWW_min; | |
1064 | }; | |
974647ea BB |
1065 | |
1066 | /* get timing characteristics from ONFI timing mode. */ | |
1067 | const struct nand_sdr_timings *onfi_async_timing_mode_to_sdr_timings(int mode); | |
730a43fb BB |
1068 | |
1069 | int nand_check_erased_ecc_chunk(void *data, int datalen, | |
1070 | void *ecc, int ecclen, | |
1071 | void *extraoob, int extraooblen, | |
1072 | int threshold); | |
1da177e4 | 1073 | #endif /* __LINUX_MTD_NAND_H */ |