Commit | Line | Data |
---|---|---|
f0706e82 | 1 | /* |
3017b80b JB |
2 | * mac80211 <-> driver interface |
3 | * | |
f0706e82 JB |
4 | * Copyright 2002-2005, Devicescape Software, Inc. |
5 | * Copyright 2006-2007 Jiri Benc <jbenc@suse.cz> | |
3017b80b | 6 | * Copyright 2007 Johannes Berg <johannes@sipsolutions.net> |
f0706e82 JB |
7 | * |
8 | * This program is free software; you can redistribute it and/or modify | |
9 | * it under the terms of the GNU General Public License version 2 as | |
10 | * published by the Free Software Foundation. | |
11 | */ | |
12 | ||
13 | #ifndef MAC80211_H | |
14 | #define MAC80211_H | |
15 | ||
16 | #include <linux/kernel.h> | |
17 | #include <linux/if_ether.h> | |
18 | #include <linux/skbuff.h> | |
19 | #include <linux/wireless.h> | |
20 | #include <linux/device.h> | |
21 | #include <linux/ieee80211.h> | |
22 | #include <net/wireless.h> | |
23 | #include <net/cfg80211.h> | |
24 | ||
75a5f0cc JB |
25 | /** |
26 | * DOC: Introduction | |
27 | * | |
28 | * mac80211 is the Linux stack for 802.11 hardware that implements | |
29 | * only partial functionality in hard- or firmware. This document | |
30 | * defines the interface between mac80211 and low-level hardware | |
31 | * drivers. | |
32 | */ | |
33 | ||
34 | /** | |
35 | * DOC: Calling mac80211 from interrupts | |
36 | * | |
37 | * Only ieee80211_tx_status_irqsafe() and ieee80211_rx_irqsafe() can be | |
f0706e82 JB |
38 | * called in hardware interrupt context. The low-level driver must not call any |
39 | * other functions in hardware interrupt context. If there is a need for such | |
40 | * call, the low-level driver should first ACK the interrupt and perform the | |
75a5f0cc | 41 | * IEEE 802.11 code call after this, e.g. from a scheduled workqueue function. |
f0706e82 JB |
42 | */ |
43 | ||
75a5f0cc JB |
44 | /** |
45 | * DOC: Warning | |
46 | * | |
47 | * If you're reading this document and not the header file itself, it will | |
48 | * be incomplete because not all documentation has been converted yet. | |
49 | */ | |
50 | ||
51 | /** | |
52 | * DOC: Frame format | |
53 | * | |
54 | * As a general rule, when frames are passed between mac80211 and the driver, | |
55 | * they start with the IEEE 802.11 header and include the same octets that are | |
56 | * sent over the air except for the FCS which should be calculated by the | |
57 | * hardware. | |
58 | * | |
59 | * There are, however, various exceptions to this rule for advanced features: | |
60 | * | |
61 | * The first exception is for hardware encryption and decryption offload | |
62 | * where the IV/ICV may or may not be generated in hardware. | |
63 | * | |
64 | * Secondly, when the hardware handles fragmentation, the frame handed to | |
65 | * the driver from mac80211 is the MSDU, not the MPDU. | |
66 | * | |
67 | * Finally, for received frames, the driver is able to indicate that it has | |
68 | * filled a radiotap header and put that in front of the frame; if it does | |
69 | * not do so then mac80211 may add this under certain circumstances. | |
f0706e82 JB |
70 | */ |
71 | ||
10816d40 RR |
72 | /** |
73 | * struct ieee80211_ht_bss_info - describing BSS's HT characteristics | |
74 | * | |
75 | * This structure describes most essential parameters needed | |
76 | * to describe 802.11n HT characteristics in a BSS | |
77 | * | |
78 | * @primary_channel: channel number of primery channel | |
79 | * @bss_cap: 802.11n's general BSS capabilities (e.g. channel width) | |
80 | * @bss_op_mode: 802.11n's BSS operation modes (e.g. HT protection) | |
81 | */ | |
82 | struct ieee80211_ht_bss_info { | |
83 | u8 primary_channel; | |
84 | u8 bss_cap; /* use IEEE80211_HT_IE_CHA_ */ | |
85 | u8 bss_op_mode; /* use IEEE80211_HT_IE_ */ | |
86 | }; | |
87 | ||
6b301cdf JB |
88 | /** |
89 | * struct ieee80211_tx_queue_params - transmit queue configuration | |
90 | * | |
91 | * The information provided in this structure is required for QoS | |
92 | * transmit queue configuration. | |
93 | * | |
94 | * @aifs: arbitration interface space [0..255, -1: use default] | |
95 | * @cw_min: minimum contention window [will be a value of the form | |
96 | * 2^n-1 in the range 1..1023; 0: use default] | |
97 | * @cw_max: maximum contention window [like @cw_min] | |
98 | * @burst_time: maximum burst time in units of 0.1ms, 0 meaning disabled | |
99 | */ | |
f0706e82 | 100 | struct ieee80211_tx_queue_params { |
6b301cdf JB |
101 | int aifs; |
102 | int cw_min; | |
103 | int cw_max; | |
104 | int burst_time; | |
f0706e82 JB |
105 | }; |
106 | ||
6b301cdf JB |
107 | /** |
108 | * struct ieee80211_tx_queue_stats_data - transmit queue statistics | |
109 | * | |
110 | * @len: number of packets in queue | |
111 | * @limit: queue length limit | |
112 | * @count: number of frames sent | |
113 | */ | |
f0706e82 | 114 | struct ieee80211_tx_queue_stats_data { |
6b301cdf JB |
115 | unsigned int len; |
116 | unsigned int limit; | |
117 | unsigned int count; | |
f0706e82 JB |
118 | }; |
119 | ||
6b301cdf JB |
120 | /** |
121 | * enum ieee80211_tx_queue - transmit queue number | |
122 | * | |
123 | * These constants are used with some callbacks that take a | |
124 | * queue number to set parameters for a queue. | |
125 | * | |
126 | * @IEEE80211_TX_QUEUE_DATA0: data queue 0 | |
127 | * @IEEE80211_TX_QUEUE_DATA1: data queue 1 | |
128 | * @IEEE80211_TX_QUEUE_DATA2: data queue 2 | |
129 | * @IEEE80211_TX_QUEUE_DATA3: data queue 3 | |
130 | * @IEEE80211_TX_QUEUE_DATA4: data queue 4 | |
131 | * @IEEE80211_TX_QUEUE_SVP: ?? | |
132 | * @NUM_TX_DATA_QUEUES: number of data queues | |
133 | * @IEEE80211_TX_QUEUE_AFTER_BEACON: transmit queue for frames to be | |
134 | * sent after a beacon | |
135 | * @IEEE80211_TX_QUEUE_BEACON: transmit queue for beacon frames | |
9e723492 | 136 | * @NUM_TX_DATA_QUEUES_AMPDU: adding more queues for A-MPDU |
6b301cdf JB |
137 | */ |
138 | enum ieee80211_tx_queue { | |
f0706e82 JB |
139 | IEEE80211_TX_QUEUE_DATA0, |
140 | IEEE80211_TX_QUEUE_DATA1, | |
141 | IEEE80211_TX_QUEUE_DATA2, | |
142 | IEEE80211_TX_QUEUE_DATA3, | |
143 | IEEE80211_TX_QUEUE_DATA4, | |
144 | IEEE80211_TX_QUEUE_SVP, | |
145 | ||
146 | NUM_TX_DATA_QUEUES, | |
147 | ||
148 | /* due to stupidity in the sub-ioctl userspace interface, the items in | |
149 | * this struct need to have fixed values. As soon as it is removed, we can | |
150 | * fix these entries. */ | |
151 | IEEE80211_TX_QUEUE_AFTER_BEACON = 6, | |
9e723492 RR |
152 | IEEE80211_TX_QUEUE_BEACON = 7, |
153 | NUM_TX_DATA_QUEUES_AMPDU = 16 | |
f0706e82 JB |
154 | }; |
155 | ||
156 | struct ieee80211_tx_queue_stats { | |
9e723492 | 157 | struct ieee80211_tx_queue_stats_data data[NUM_TX_DATA_QUEUES_AMPDU]; |
f0706e82 JB |
158 | }; |
159 | ||
160 | struct ieee80211_low_level_stats { | |
161 | unsigned int dot11ACKFailureCount; | |
162 | unsigned int dot11RTSFailureCount; | |
163 | unsigned int dot11FCSErrorCount; | |
164 | unsigned int dot11RTSSuccessCount; | |
165 | }; | |
166 | ||
471b3efd JB |
167 | /** |
168 | * enum ieee80211_bss_change - BSS change notification flags | |
169 | * | |
170 | * These flags are used with the bss_info_changed() callback | |
171 | * to indicate which BSS parameter changed. | |
172 | * | |
173 | * @BSS_CHANGED_ASSOC: association status changed (associated/disassociated), | |
174 | * also implies a change in the AID. | |
175 | * @BSS_CHANGED_ERP_CTS_PROT: CTS protection changed | |
176 | * @BSS_CHANGED_ERP_PREAMBLE: preamble changed | |
177 | */ | |
178 | enum ieee80211_bss_change { | |
179 | BSS_CHANGED_ASSOC = 1<<0, | |
180 | BSS_CHANGED_ERP_CTS_PROT = 1<<1, | |
181 | BSS_CHANGED_ERP_PREAMBLE = 1<<2, | |
182 | }; | |
183 | ||
184 | /** | |
185 | * struct ieee80211_bss_conf - holds the BSS's changing parameters | |
186 | * | |
187 | * This structure keeps information about a BSS (and an association | |
188 | * to that BSS) that can change during the lifetime of the BSS. | |
189 | * | |
190 | * @assoc: association status | |
191 | * @aid: association ID number, valid only when @assoc is true | |
192 | * @use_cts_prot: use CTS protection | |
193 | * @use_short_preamble: use 802.11b short preamble | |
194 | */ | |
195 | struct ieee80211_bss_conf { | |
196 | /* association related data */ | |
197 | bool assoc; | |
198 | u16 aid; | |
199 | /* erp related data */ | |
200 | bool use_cts_prot; | |
201 | bool use_short_preamble; | |
202 | }; | |
203 | ||
f0706e82 JB |
204 | /* Transmit control fields. This data structure is passed to low-level driver |
205 | * with each TX frame. The low-level driver is responsible for configuring | |
206 | * the hardware to use given values (depending on what is supported). */ | |
f0706e82 JB |
207 | |
208 | struct ieee80211_tx_control { | |
32bfd35d | 209 | struct ieee80211_vif *vif; |
8318d78a JB |
210 | struct ieee80211_rate *tx_rate; |
211 | ||
212 | /* Transmit rate for RTS/CTS frame */ | |
213 | struct ieee80211_rate *rts_cts_rate; | |
214 | ||
215 | /* retry rate for the last retries */ | |
216 | struct ieee80211_rate *alt_retry_rate; | |
f0706e82 JB |
217 | |
218 | #define IEEE80211_TXCTL_REQ_TX_STATUS (1<<0)/* request TX status callback for | |
219 | * this frame */ | |
220 | #define IEEE80211_TXCTL_DO_NOT_ENCRYPT (1<<1) /* send this frame without | |
221 | * encryption; e.g., for EAPOL | |
222 | * frames */ | |
223 | #define IEEE80211_TXCTL_USE_RTS_CTS (1<<2) /* use RTS-CTS before sending | |
224 | * frame */ | |
225 | #define IEEE80211_TXCTL_USE_CTS_PROTECT (1<<3) /* use CTS protection for the | |
226 | * frame (e.g., for combined | |
227 | * 802.11g / 802.11b networks) */ | |
228 | #define IEEE80211_TXCTL_NO_ACK (1<<4) /* tell the low level not to | |
229 | * wait for an ack */ | |
230 | #define IEEE80211_TXCTL_RATE_CTRL_PROBE (1<<5) | |
231 | #define IEEE80211_TXCTL_CLEAR_DST_MASK (1<<6) | |
232 | #define IEEE80211_TXCTL_REQUEUE (1<<7) | |
233 | #define IEEE80211_TXCTL_FIRST_FRAGMENT (1<<8) /* this is a first fragment of | |
234 | * the frame */ | |
8318d78a | 235 | #define IEEE80211_TXCTL_SHORT_PREAMBLE (1<<9) |
d5d08def ID |
236 | #define IEEE80211_TXCTL_LONG_RETRY_LIMIT (1<<10) /* this frame should be send |
237 | * using the through | |
238 | * set_retry_limit configured | |
239 | * long retry value */ | |
678f5f71 | 240 | #define IEEE80211_TXCTL_EAPOL_FRAME (1<<11) /* internal to mac80211 */ |
7d54d0dd JB |
241 | #define IEEE80211_TXCTL_SEND_AFTER_DTIM (1<<12) /* send this frame after DTIM |
242 | * beacon */ | |
9e723492 RR |
243 | #define IEEE80211_TXCTL_AMPDU (1<<13) /* this frame should be sent |
244 | * as part of an A-MPDU */ | |
f0706e82 JB |
245 | u32 flags; /* tx control flags defined |
246 | * above */ | |
6a7664d4 JB |
247 | u8 key_idx; /* keyidx from hw->set_key(), undefined if |
248 | * IEEE80211_TXCTL_DO_NOT_ENCRYPT is set */ | |
d5d08def ID |
249 | u8 retry_limit; /* 1 = only first attempt, 2 = one retry, .. |
250 | * This could be used when set_retry_limit | |
251 | * is not implemented by the driver */ | |
f0706e82 | 252 | u8 antenna_sel_tx; /* 0 = default/diversity, 1 = Ant0, 2 = Ant1 */ |
f0706e82 JB |
253 | u8 icv_len; /* length of the ICV/MIC field in octets */ |
254 | u8 iv_len; /* length of the IV field in octets */ | |
f0706e82 JB |
255 | u8 queue; /* hardware queue to use for this frame; |
256 | * 0 = highest, hw->queues-1 = lowest */ | |
f0706e82 | 257 | int type; /* internal */ |
f0706e82 JB |
258 | }; |
259 | ||
7ac1bd6a JB |
260 | |
261 | /** | |
262 | * enum mac80211_rx_flags - receive flags | |
263 | * | |
264 | * These flags are used with the @flag member of &struct ieee80211_rx_status. | |
265 | * @RX_FLAG_MMIC_ERROR: Michael MIC error was reported on this frame. | |
266 | * Use together with %RX_FLAG_MMIC_STRIPPED. | |
267 | * @RX_FLAG_DECRYPTED: This frame was decrypted in hardware. | |
268 | * @RX_FLAG_RADIOTAP: This frame starts with a radiotap header. | |
269 | * @RX_FLAG_MMIC_STRIPPED: the Michael MIC is stripped off this frame, | |
270 | * verification has been done by the hardware. | |
271 | * @RX_FLAG_IV_STRIPPED: The IV/ICV are stripped from this frame. | |
272 | * If this flag is set, the stack cannot do any replay detection | |
273 | * hence the driver or hardware will have to do that. | |
72abd81b JB |
274 | * @RX_FLAG_FAILED_FCS_CRC: Set this flag if the FCS check failed on |
275 | * the frame. | |
276 | * @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on | |
277 | * the frame. | |
c49e5ea3 JB |
278 | * @RX_FLAG_TSFT: The timestamp passed in the RX status (@mactime field) |
279 | * is valid. | |
7ac1bd6a JB |
280 | */ |
281 | enum mac80211_rx_flags { | |
282 | RX_FLAG_MMIC_ERROR = 1<<0, | |
283 | RX_FLAG_DECRYPTED = 1<<1, | |
284 | RX_FLAG_RADIOTAP = 1<<2, | |
285 | RX_FLAG_MMIC_STRIPPED = 1<<3, | |
286 | RX_FLAG_IV_STRIPPED = 1<<4, | |
72abd81b JB |
287 | RX_FLAG_FAILED_FCS_CRC = 1<<5, |
288 | RX_FLAG_FAILED_PLCP_CRC = 1<<6, | |
c49e5ea3 | 289 | RX_FLAG_TSFT = 1<<7, |
7ac1bd6a JB |
290 | }; |
291 | ||
292 | /** | |
293 | * struct ieee80211_rx_status - receive status | |
294 | * | |
295 | * The low-level driver should provide this information (the subset | |
296 | * supported by hardware) to the 802.11 code with each received | |
297 | * frame. | |
298 | * @mactime: MAC timestamp as defined by 802.11 | |
8318d78a | 299 | * @band: the active band when this frame was received |
7ac1bd6a | 300 | * @freq: frequency the radio was tuned to when receiving this frame, in MHz |
7ac1bd6a JB |
301 | * @ssi: signal strength when receiving this frame |
302 | * @signal: used as 'qual' in statistics reporting | |
303 | * @noise: PHY noise when receiving this frame | |
304 | * @antenna: antenna used | |
8318d78a | 305 | * @rate_idx: index of data rate into band's supported rates |
7ac1bd6a JB |
306 | * @flag: %RX_FLAG_* |
307 | */ | |
f0706e82 JB |
308 | struct ieee80211_rx_status { |
309 | u64 mactime; | |
8318d78a | 310 | enum ieee80211_band band; |
7ac1bd6a | 311 | int freq; |
f0706e82 | 312 | int ssi; |
7ac1bd6a | 313 | int signal; |
f0706e82 JB |
314 | int noise; |
315 | int antenna; | |
8318d78a | 316 | int rate_idx; |
f0706e82 JB |
317 | int flag; |
318 | }; | |
319 | ||
6b301cdf JB |
320 | /** |
321 | * enum ieee80211_tx_status_flags - transmit status flags | |
322 | * | |
323 | * Status flags to indicate various transmit conditions. | |
324 | * | |
325 | * @IEEE80211_TX_STATUS_TX_FILTERED: The frame was not transmitted | |
326 | * because the destination STA was in powersave mode. | |
6b301cdf | 327 | * @IEEE80211_TX_STATUS_ACK: Frame was acknowledged |
483fdcec RR |
328 | * @IEEE80211_TX_STATUS_AMPDU: The frame was aggregated, so status |
329 | * is for the whole aggregation. | |
6b301cdf JB |
330 | */ |
331 | enum ieee80211_tx_status_flags { | |
332 | IEEE80211_TX_STATUS_TX_FILTERED = 1<<0, | |
333 | IEEE80211_TX_STATUS_ACK = 1<<1, | |
483fdcec | 334 | IEEE80211_TX_STATUS_AMPDU = 1<<2, |
6b301cdf JB |
335 | }; |
336 | ||
337 | /** | |
338 | * struct ieee80211_tx_status - transmit status | |
339 | * | |
340 | * As much information as possible should be provided for each transmitted | |
341 | * frame with ieee80211_tx_status(). | |
342 | * | |
343 | * @control: a copy of the &struct ieee80211_tx_control passed to the driver | |
344 | * in the tx() callback. | |
6b301cdf | 345 | * @flags: transmit status flags, defined above |
483fdcec | 346 | * @retry_count: number of retries |
6b301cdf JB |
347 | * @excessive_retries: set to 1 if the frame was retried many times |
348 | * but not acknowledged | |
483fdcec RR |
349 | * @ampdu_ack_len: number of aggregated frames. |
350 | * relevant only if IEEE80211_TX_STATUS_AMPDU was set. | |
351 | * @ampdu_ack_map: block ack bit map for the aggregation. | |
352 | * relevant only if IEEE80211_TX_STATUS_AMPDU was set. | |
353 | * @ack_signal: signal strength of the ACK frame | |
6b301cdf JB |
354 | * @queue_length: ?? REMOVE |
355 | * @queue_number: ?? REMOVE | |
356 | */ | |
f0706e82 | 357 | struct ieee80211_tx_status { |
f0706e82 | 358 | struct ieee80211_tx_control control; |
6b301cdf | 359 | u8 flags; |
6b301cdf | 360 | u8 retry_count; |
483fdcec RR |
361 | bool excessive_retries; |
362 | u8 ampdu_ack_len; | |
363 | u64 ampdu_ack_map; | |
6b301cdf JB |
364 | int ack_signal; |
365 | int queue_length; | |
f0706e82 JB |
366 | int queue_number; |
367 | }; | |
368 | ||
6b301cdf JB |
369 | /** |
370 | * enum ieee80211_conf_flags - configuration flags | |
371 | * | |
372 | * Flags to define PHY configuration options | |
373 | * | |
374 | * @IEEE80211_CONF_SHORT_SLOT_TIME: use 802.11g short slot time | |
375 | * @IEEE80211_CONF_RADIOTAP: add radiotap header at receive time (if supported) | |
10816d40 | 376 | * @IEEE80211_CONF_SUPPORT_HT_MODE: use 802.11n HT capabilities (if supported) |
6b301cdf JB |
377 | */ |
378 | enum ieee80211_conf_flags { | |
10816d40 RR |
379 | IEEE80211_CONF_SHORT_SLOT_TIME = (1<<0), |
380 | IEEE80211_CONF_RADIOTAP = (1<<1), | |
381 | IEEE80211_CONF_SUPPORT_HT_MODE = (1<<2), | |
6b301cdf | 382 | }; |
f0706e82 JB |
383 | |
384 | /** | |
385 | * struct ieee80211_conf - configuration of the device | |
386 | * | |
387 | * This struct indicates how the driver shall configure the hardware. | |
388 | * | |
389 | * @radio_enabled: when zero, driver is required to switch off the radio. | |
6b301cdf | 390 | * TODO make a flag |
6b301cdf JB |
391 | * @beacon_int: beacon interval (TODO make interface config) |
392 | * @flags: configuration flags defined above | |
8318d78a JB |
393 | * @power_level: requested transmit power (in dBm) |
394 | * @max_antenna_gain: maximum antenna gain (in dBi) | |
6b301cdf JB |
395 | * @antenna_sel_tx: transmit antenna selection, 0: default/diversity, |
396 | * 1/2: antenna 0/1 | |
397 | * @antenna_sel_rx: receive antenna selection, like @antenna_sel_tx | |
10816d40 RR |
398 | * @ht_conf: describes current self configuration of 802.11n HT capabilies |
399 | * @ht_bss_conf: describes current BSS configuration of 802.11n HT parameters | |
8318d78a | 400 | * @channel: the channel to tune to |
f0706e82 JB |
401 | */ |
402 | struct ieee80211_conf { | |
f0706e82 JB |
403 | unsigned int regulatory_domain; |
404 | int radio_enabled; | |
405 | ||
406 | int beacon_int; | |
6b301cdf | 407 | u32 flags; |
8318d78a JB |
408 | int power_level; |
409 | int max_antenna_gain; | |
f0706e82 JB |
410 | u8 antenna_sel_tx; |
411 | u8 antenna_sel_rx; | |
10816d40 | 412 | |
8318d78a JB |
413 | struct ieee80211_channel *channel; |
414 | ||
10816d40 RR |
415 | struct ieee80211_ht_info ht_conf; |
416 | struct ieee80211_ht_bss_info ht_bss_conf; | |
f0706e82 JB |
417 | }; |
418 | ||
419 | /** | |
420 | * enum ieee80211_if_types - types of 802.11 network interfaces | |
421 | * | |
a2897552 JB |
422 | * @IEEE80211_IF_TYPE_INVALID: invalid interface type, not used |
423 | * by mac80211 itself | |
f0706e82 JB |
424 | * @IEEE80211_IF_TYPE_AP: interface in AP mode. |
425 | * @IEEE80211_IF_TYPE_MGMT: special interface for communication with hostap | |
426 | * daemon. Drivers should never see this type. | |
427 | * @IEEE80211_IF_TYPE_STA: interface in STA (client) mode. | |
428 | * @IEEE80211_IF_TYPE_IBSS: interface in IBSS (ad-hoc) mode. | |
429 | * @IEEE80211_IF_TYPE_MNTR: interface in monitor (rfmon) mode. | |
430 | * @IEEE80211_IF_TYPE_WDS: interface in WDS mode. | |
0ec3ca44 JB |
431 | * @IEEE80211_IF_TYPE_VLAN: VLAN interface bound to an AP, drivers |
432 | * will never see this type. | |
f0706e82 JB |
433 | */ |
434 | enum ieee80211_if_types { | |
a2897552 | 435 | IEEE80211_IF_TYPE_INVALID, |
0ec3ca44 | 436 | IEEE80211_IF_TYPE_AP, |
0ec3ca44 JB |
437 | IEEE80211_IF_TYPE_STA, |
438 | IEEE80211_IF_TYPE_IBSS, | |
439 | IEEE80211_IF_TYPE_MNTR, | |
440 | IEEE80211_IF_TYPE_WDS, | |
441 | IEEE80211_IF_TYPE_VLAN, | |
f0706e82 JB |
442 | }; |
443 | ||
32bfd35d JB |
444 | /** |
445 | * struct ieee80211_vif - per-interface data | |
446 | * | |
447 | * Data in this structure is continually present for driver | |
448 | * use during the life of a virtual interface. | |
449 | * | |
51fb61e7 | 450 | * @type: type of this virtual interface |
32bfd35d JB |
451 | * @drv_priv: data area for driver use, will always be aligned to |
452 | * sizeof(void *). | |
453 | */ | |
454 | struct ieee80211_vif { | |
51fb61e7 | 455 | enum ieee80211_if_types type; |
32bfd35d JB |
456 | /* must be last */ |
457 | u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *)))); | |
458 | }; | |
459 | ||
f0706e82 JB |
460 | /** |
461 | * struct ieee80211_if_init_conf - initial configuration of an interface | |
462 | * | |
32bfd35d JB |
463 | * @vif: pointer to a driver-use per-interface structure. The pointer |
464 | * itself is also used for various functions including | |
465 | * ieee80211_beacon_get() and ieee80211_get_buffered_bc(). | |
f0706e82 JB |
466 | * @type: one of &enum ieee80211_if_types constants. Determines the type of |
467 | * added/removed interface. | |
468 | * @mac_addr: pointer to MAC address of the interface. This pointer is valid | |
469 | * until the interface is removed (i.e. it cannot be used after | |
470 | * remove_interface() callback was called for this interface). | |
471 | * | |
472 | * This structure is used in add_interface() and remove_interface() | |
473 | * callbacks of &struct ieee80211_hw. | |
4480f15c JB |
474 | * |
475 | * When you allow multiple interfaces to be added to your PHY, take care | |
476 | * that the hardware can actually handle multiple MAC addresses. However, | |
477 | * also take care that when there's no interface left with mac_addr != %NULL | |
478 | * you remove the MAC address from the device to avoid acknowledging packets | |
479 | * in pure monitor mode. | |
f0706e82 JB |
480 | */ |
481 | struct ieee80211_if_init_conf { | |
75a5f0cc | 482 | enum ieee80211_if_types type; |
32bfd35d | 483 | struct ieee80211_vif *vif; |
f0706e82 JB |
484 | void *mac_addr; |
485 | }; | |
486 | ||
487 | /** | |
488 | * struct ieee80211_if_conf - configuration of an interface | |
489 | * | |
490 | * @type: type of the interface. This is always the same as was specified in | |
491 | * &struct ieee80211_if_init_conf. The type of an interface never changes | |
492 | * during the life of the interface; this field is present only for | |
493 | * convenience. | |
494 | * @bssid: BSSID of the network we are associated to/creating. | |
495 | * @ssid: used (together with @ssid_len) by drivers for hardware that | |
496 | * generate beacons independently. The pointer is valid only during the | |
497 | * config_interface() call, so copy the value somewhere if you need | |
498 | * it. | |
499 | * @ssid_len: length of the @ssid field. | |
f0706e82 JB |
500 | * @beacon: beacon template. Valid only if @host_gen_beacon_template in |
501 | * &struct ieee80211_hw is set. The driver is responsible of freeing | |
502 | * the sk_buff. | |
503 | * @beacon_control: tx_control for the beacon template, this field is only | |
504 | * valid when the @beacon field was set. | |
505 | * | |
506 | * This structure is passed to the config_interface() callback of | |
507 | * &struct ieee80211_hw. | |
508 | */ | |
509 | struct ieee80211_if_conf { | |
510 | int type; | |
511 | u8 *bssid; | |
512 | u8 *ssid; | |
513 | size_t ssid_len; | |
f0706e82 JB |
514 | struct sk_buff *beacon; |
515 | struct ieee80211_tx_control *beacon_control; | |
516 | }; | |
517 | ||
7ac1bd6a JB |
518 | /** |
519 | * enum ieee80211_key_alg - key algorithm | |
7ac1bd6a JB |
520 | * @ALG_WEP: WEP40 or WEP104 |
521 | * @ALG_TKIP: TKIP | |
522 | * @ALG_CCMP: CCMP (AES) | |
523 | */ | |
ea49c359 | 524 | enum ieee80211_key_alg { |
8f20fc24 JB |
525 | ALG_WEP, |
526 | ALG_TKIP, | |
527 | ALG_CCMP, | |
ea49c359 | 528 | }; |
f0706e82 | 529 | |
7ac1bd6a JB |
530 | |
531 | /** | |
532 | * enum ieee80211_key_flags - key flags | |
533 | * | |
534 | * These flags are used for communication about keys between the driver | |
535 | * and mac80211, with the @flags parameter of &struct ieee80211_key_conf. | |
536 | * | |
537 | * @IEEE80211_KEY_FLAG_WMM_STA: Set by mac80211, this flag indicates | |
538 | * that the STA this key will be used with could be using QoS. | |
539 | * @IEEE80211_KEY_FLAG_GENERATE_IV: This flag should be set by the | |
540 | * driver to indicate that it requires IV generation for this | |
541 | * particular key. | |
542 | * @IEEE80211_KEY_FLAG_GENERATE_MMIC: This flag should be set by | |
543 | * the driver for a TKIP key if it requires Michael MIC | |
544 | * generation in software. | |
7848ba7d | 545 | */ |
7ac1bd6a JB |
546 | enum ieee80211_key_flags { |
547 | IEEE80211_KEY_FLAG_WMM_STA = 1<<0, | |
548 | IEEE80211_KEY_FLAG_GENERATE_IV = 1<<1, | |
549 | IEEE80211_KEY_FLAG_GENERATE_MMIC= 1<<2, | |
550 | }; | |
11a843b7 | 551 | |
7ac1bd6a JB |
552 | /** |
553 | * struct ieee80211_key_conf - key information | |
554 | * | |
555 | * This key information is given by mac80211 to the driver by | |
556 | * the set_key() callback in &struct ieee80211_ops. | |
557 | * | |
558 | * @hw_key_idx: To be set by the driver, this is the key index the driver | |
559 | * wants to be given when a frame is transmitted and needs to be | |
6a7664d4 | 560 | * encrypted in hardware. |
7ac1bd6a JB |
561 | * @alg: The key algorithm. |
562 | * @flags: key flags, see &enum ieee80211_key_flags. | |
563 | * @keyidx: the key index (0-3) | |
564 | * @keylen: key material length | |
565 | * @key: key material | |
566 | */ | |
f0706e82 | 567 | struct ieee80211_key_conf { |
ea49c359 | 568 | enum ieee80211_key_alg alg; |
6a7664d4 | 569 | u8 hw_key_idx; |
11a843b7 | 570 | u8 flags; |
11a843b7 | 571 | s8 keyidx; |
11a843b7 | 572 | u8 keylen; |
f0706e82 JB |
573 | u8 key[0]; |
574 | }; | |
575 | ||
7ac1bd6a JB |
576 | /** |
577 | * enum set_key_cmd - key command | |
578 | * | |
579 | * Used with the set_key() callback in &struct ieee80211_ops, this | |
580 | * indicates whether a key is being removed or added. | |
581 | * | |
582 | * @SET_KEY: a key is set | |
583 | * @DISABLE_KEY: a key must be disabled | |
584 | */ | |
ea49c359 | 585 | enum set_key_cmd { |
11a843b7 | 586 | SET_KEY, DISABLE_KEY, |
ea49c359 | 587 | }; |
f0706e82 | 588 | |
478f8d2b TW |
589 | /** |
590 | * enum sta_notify_cmd - sta notify command | |
591 | * | |
592 | * Used with the sta_notify() callback in &struct ieee80211_ops, this | |
593 | * indicates addition and removal of a station to station table | |
594 | * | |
595 | * @STA_NOTIFY_ADD: a station was added to the station table | |
596 | * @STA_NOTIFY_REMOVE: a station being removed from the station table | |
597 | */ | |
598 | enum sta_notify_cmd { | |
599 | STA_NOTIFY_ADD, STA_NOTIFY_REMOVE | |
600 | }; | |
1bc0826c JB |
601 | |
602 | /** | |
603 | * enum ieee80211_hw_flags - hardware flags | |
604 | * | |
605 | * These flags are used to indicate hardware capabilities to | |
606 | * the stack. Generally, flags here should have their meaning | |
607 | * done in a way that the simplest hardware doesn't need setting | |
608 | * any particular flags. There are some exceptions to this rule, | |
609 | * however, so you are advised to review these flags carefully. | |
610 | * | |
611 | * @IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE: | |
612 | * The device only needs to be supplied with a beacon template. | |
613 | * If you need the host to generate each beacon then don't use | |
614 | * this flag and call ieee80211_beacon_get() when you need the | |
615 | * next beacon frame. Note that if you set this flag, you must | |
616 | * implement the set_tim() callback for powersave mode to work | |
617 | * properly. | |
618 | * This flag is only relevant for access-point mode. | |
619 | * | |
620 | * @IEEE80211_HW_RX_INCLUDES_FCS: | |
621 | * Indicates that received frames passed to the stack include | |
622 | * the FCS at the end. | |
623 | * | |
624 | * @IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING: | |
625 | * Some wireless LAN chipsets buffer broadcast/multicast frames | |
626 | * for power saving stations in the hardware/firmware and others | |
627 | * rely on the host system for such buffering. This option is used | |
628 | * to configure the IEEE 802.11 upper layer to buffer broadcast and | |
629 | * multicast frames when there are power saving stations so that | |
630 | * the driver can fetch them with ieee80211_get_buffered_bc(). Note | |
631 | * that not setting this flag works properly only when the | |
632 | * %IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE is also not set because | |
633 | * otherwise the stack will not know when the DTIM beacon was sent. | |
634 | * | |
8318d78a JB |
635 | * @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE: |
636 | * Hardware is not capable of short slot operation on the 2.4 GHz band. | |
637 | * | |
638 | * @IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE: | |
639 | * Hardware is not capable of receiving frames with short preamble on | |
640 | * the 2.4 GHz band. | |
1bc0826c JB |
641 | */ |
642 | enum ieee80211_hw_flags { | |
643 | IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE = 1<<0, | |
644 | IEEE80211_HW_RX_INCLUDES_FCS = 1<<1, | |
645 | IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING = 1<<2, | |
8318d78a JB |
646 | IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE = 1<<3, |
647 | IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE = 1<<4, | |
1bc0826c JB |
648 | }; |
649 | ||
7ac1bd6a JB |
650 | /** |
651 | * struct ieee80211_hw - hardware information and state | |
75a5f0cc JB |
652 | * |
653 | * This structure contains the configuration and hardware | |
654 | * information for an 802.11 PHY. | |
655 | * | |
656 | * @wiphy: This points to the &struct wiphy allocated for this | |
657 | * 802.11 PHY. You must fill in the @perm_addr and @dev | |
658 | * members of this structure using SET_IEEE80211_DEV() | |
8318d78a JB |
659 | * and SET_IEEE80211_PERM_ADDR(). Additionally, all supported |
660 | * bands (with channels, bitrates) are registered here. | |
75a5f0cc JB |
661 | * |
662 | * @conf: &struct ieee80211_conf, device configuration, don't use. | |
663 | * | |
664 | * @workqueue: single threaded workqueue available for driver use, | |
665 | * allocated by mac80211 on registration and flushed on | |
666 | * unregistration. | |
667 | * | |
668 | * @priv: pointer to private area that was allocated for driver use | |
669 | * along with this structure. | |
670 | * | |
671 | * @flags: hardware flags, see &enum ieee80211_hw_flags. | |
672 | * | |
673 | * @extra_tx_headroom: headroom to reserve in each transmit skb | |
674 | * for use by the driver (e.g. for transmit headers.) | |
675 | * | |
676 | * @channel_change_time: time (in microseconds) it takes to change channels. | |
677 | * | |
678 | * @max_rssi: Maximum value for ssi in RX information, use | |
679 | * negative numbers for dBm and 0 to indicate no support. | |
680 | * | |
681 | * @max_signal: like @max_rssi, but for the signal value. | |
682 | * | |
683 | * @max_noise: like @max_rssi, but for the noise value. | |
684 | * | |
685 | * @queues: number of available hardware transmit queues for | |
686 | * data packets. WMM/QoS requires at least four. | |
830f9038 JB |
687 | * |
688 | * @rate_control_algorithm: rate control algorithm for this hardware. | |
689 | * If unset (NULL), the default algorithm will be used. Must be | |
690 | * set before calling ieee80211_register_hw(). | |
32bfd35d JB |
691 | * |
692 | * @vif_data_size: size (in bytes) of the drv_priv data area | |
693 | * within &struct ieee80211_vif. | |
7ac1bd6a | 694 | */ |
f0706e82 | 695 | struct ieee80211_hw { |
f0706e82 | 696 | struct ieee80211_conf conf; |
75a5f0cc | 697 | struct wiphy *wiphy; |
f0706e82 | 698 | struct workqueue_struct *workqueue; |
830f9038 | 699 | const char *rate_control_algorithm; |
f0706e82 | 700 | void *priv; |
75a5f0cc | 701 | u32 flags; |
f0706e82 | 702 | unsigned int extra_tx_headroom; |
f0706e82 | 703 | int channel_change_time; |
32bfd35d | 704 | int vif_data_size; |
75a5f0cc | 705 | u8 queues; |
f0706e82 JB |
706 | s8 max_rssi; |
707 | s8 max_signal; | |
708 | s8 max_noise; | |
f0706e82 JB |
709 | }; |
710 | ||
75a5f0cc JB |
711 | /** |
712 | * SET_IEEE80211_DEV - set device for 802.11 hardware | |
713 | * | |
714 | * @hw: the &struct ieee80211_hw to set the device for | |
715 | * @dev: the &struct device of this 802.11 device | |
716 | */ | |
f0706e82 JB |
717 | static inline void SET_IEEE80211_DEV(struct ieee80211_hw *hw, struct device *dev) |
718 | { | |
719 | set_wiphy_dev(hw->wiphy, dev); | |
720 | } | |
721 | ||
75a5f0cc JB |
722 | /** |
723 | * SET_IEEE80211_PERM_ADDR - set the permanenet MAC address for 802.11 hardware | |
724 | * | |
725 | * @hw: the &struct ieee80211_hw to set the MAC address for | |
726 | * @addr: the address to set | |
727 | */ | |
f0706e82 JB |
728 | static inline void SET_IEEE80211_PERM_ADDR(struct ieee80211_hw *hw, u8 *addr) |
729 | { | |
730 | memcpy(hw->wiphy->perm_addr, addr, ETH_ALEN); | |
731 | } | |
732 | ||
75a5f0cc JB |
733 | /** |
734 | * DOC: Hardware crypto acceleration | |
735 | * | |
736 | * mac80211 is capable of taking advantage of many hardware | |
737 | * acceleration designs for encryption and decryption operations. | |
738 | * | |
739 | * The set_key() callback in the &struct ieee80211_ops for a given | |
740 | * device is called to enable hardware acceleration of encryption and | |
741 | * decryption. The callback takes an @address parameter that will be | |
742 | * the broadcast address for default keys, the other station's hardware | |
743 | * address for individual keys or the zero address for keys that will | |
744 | * be used only for transmission. | |
745 | * Multiple transmission keys with the same key index may be used when | |
746 | * VLANs are configured for an access point. | |
4150c572 | 747 | * |
75a5f0cc JB |
748 | * The @local_address parameter will always be set to our own address, |
749 | * this is only relevant if you support multiple local addresses. | |
750 | * | |
751 | * When transmitting, the TX control data will use the @hw_key_idx | |
752 | * selected by the driver by modifying the &struct ieee80211_key_conf | |
753 | * pointed to by the @key parameter to the set_key() function. | |
754 | * | |
755 | * The set_key() call for the %SET_KEY command should return 0 if | |
756 | * the key is now in use, -%EOPNOTSUPP or -%ENOSPC if it couldn't be | |
757 | * added; if you return 0 then hw_key_idx must be assigned to the | |
758 | * hardware key index, you are free to use the full u8 range. | |
759 | * | |
760 | * When the cmd is %DISABLE_KEY then it must succeed. | |
761 | * | |
762 | * Note that it is permissible to not decrypt a frame even if a key | |
763 | * for it has been uploaded to hardware, the stack will not make any | |
764 | * decision based on whether a key has been uploaded or not but rather | |
765 | * based on the receive flags. | |
766 | * | |
767 | * The &struct ieee80211_key_conf structure pointed to by the @key | |
768 | * parameter is guaranteed to be valid until another call to set_key() | |
769 | * removes it, but it can only be used as a cookie to differentiate | |
770 | * keys. | |
4150c572 | 771 | */ |
75a5f0cc JB |
772 | |
773 | /** | |
774 | * DOC: Frame filtering | |
775 | * | |
776 | * mac80211 requires to see many management frames for proper | |
777 | * operation, and users may want to see many more frames when | |
778 | * in monitor mode. However, for best CPU usage and power consumption, | |
779 | * having as few frames as possible percolate through the stack is | |
780 | * desirable. Hence, the hardware should filter as much as possible. | |
781 | * | |
782 | * To achieve this, mac80211 uses filter flags (see below) to tell | |
783 | * the driver's configure_filter() function which frames should be | |
784 | * passed to mac80211 and which should be filtered out. | |
785 | * | |
786 | * The configure_filter() callback is invoked with the parameters | |
787 | * @mc_count and @mc_list for the combined multicast address list | |
788 | * of all virtual interfaces, @changed_flags telling which flags | |
789 | * were changed and @total_flags with the new flag states. | |
790 | * | |
791 | * If your device has no multicast address filters your driver will | |
792 | * need to check both the %FIF_ALLMULTI flag and the @mc_count | |
793 | * parameter to see whether multicast frames should be accepted | |
794 | * or dropped. | |
795 | * | |
796 | * All unsupported flags in @total_flags must be cleared, i.e. you | |
797 | * should clear all bits except those you honoured. | |
4150c572 | 798 | */ |
75a5f0cc JB |
799 | |
800 | /** | |
801 | * enum ieee80211_filter_flags - hardware filter flags | |
802 | * | |
803 | * These flags determine what the filter in hardware should be | |
804 | * programmed to let through and what should not be passed to the | |
805 | * stack. It is always safe to pass more frames than requested, | |
806 | * but this has negative impact on power consumption. | |
807 | * | |
808 | * @FIF_PROMISC_IN_BSS: promiscuous mode within your BSS, | |
809 | * think of the BSS as your network segment and then this corresponds | |
810 | * to the regular ethernet device promiscuous mode. | |
811 | * | |
812 | * @FIF_ALLMULTI: pass all multicast frames, this is used if requested | |
813 | * by the user or if the hardware is not capable of filtering by | |
814 | * multicast address. | |
815 | * | |
816 | * @FIF_FCSFAIL: pass frames with failed FCS (but you need to set the | |
817 | * %RX_FLAG_FAILED_FCS_CRC for them) | |
818 | * | |
819 | * @FIF_PLCPFAIL: pass frames with failed PLCP CRC (but you need to set | |
820 | * the %RX_FLAG_FAILED_PLCP_CRC for them | |
821 | * | |
822 | * @FIF_BCN_PRBRESP_PROMISC: This flag is set during scanning to indicate | |
823 | * to the hardware that it should not filter beacons or probe responses | |
824 | * by BSSID. Filtering them can greatly reduce the amount of processing | |
825 | * mac80211 needs to do and the amount of CPU wakeups, so you should | |
826 | * honour this flag if possible. | |
827 | * | |
828 | * @FIF_CONTROL: pass control frames, if PROMISC_IN_BSS is not set then | |
829 | * only those addressed to this station | |
830 | * | |
831 | * @FIF_OTHER_BSS: pass frames destined to other BSSes | |
4150c572 | 832 | */ |
75a5f0cc JB |
833 | enum ieee80211_filter_flags { |
834 | FIF_PROMISC_IN_BSS = 1<<0, | |
835 | FIF_ALLMULTI = 1<<1, | |
836 | FIF_FCSFAIL = 1<<2, | |
837 | FIF_PLCPFAIL = 1<<3, | |
838 | FIF_BCN_PRBRESP_PROMISC = 1<<4, | |
839 | FIF_CONTROL = 1<<5, | |
840 | FIF_OTHER_BSS = 1<<6, | |
841 | }; | |
842 | ||
1b7d03ac RR |
843 | /** |
844 | * enum ieee80211_ampdu_mlme_action - A-MPDU actions | |
845 | * | |
846 | * These flags are used with the ampdu_action() callback in | |
847 | * &struct ieee80211_ops to indicate which action is needed. | |
848 | * @IEEE80211_AMPDU_RX_START: start Rx aggregation | |
849 | * @IEEE80211_AMPDU_RX_STOP: stop Rx aggregation | |
0df3ef45 RR |
850 | * @IEEE80211_AMPDU_TX_START: start Tx aggregation |
851 | * @IEEE80211_AMPDU_TX_STOP: stop Tx aggregation | |
1b7d03ac RR |
852 | */ |
853 | enum ieee80211_ampdu_mlme_action { | |
854 | IEEE80211_AMPDU_RX_START, | |
855 | IEEE80211_AMPDU_RX_STOP, | |
0df3ef45 RR |
856 | IEEE80211_AMPDU_TX_START, |
857 | IEEE80211_AMPDU_TX_STOP, | |
1b7d03ac | 858 | }; |
75a5f0cc JB |
859 | |
860 | /** | |
861 | * struct ieee80211_ops - callbacks from mac80211 to the driver | |
862 | * | |
863 | * This structure contains various callbacks that the driver may | |
864 | * handle or, in some cases, must handle, for example to configure | |
865 | * the hardware to a new channel or to transmit a frame. | |
866 | * | |
867 | * @tx: Handler that 802.11 module calls for each transmitted frame. | |
868 | * skb contains the buffer starting from the IEEE 802.11 header. | |
869 | * The low-level driver should send the frame out based on | |
870 | * configuration in the TX control data. Must be implemented and | |
871 | * atomic. | |
872 | * | |
873 | * @start: Called before the first netdevice attached to the hardware | |
874 | * is enabled. This should turn on the hardware and must turn on | |
875 | * frame reception (for possibly enabled monitor interfaces.) | |
876 | * Returns negative error codes, these may be seen in userspace, | |
877 | * or zero. | |
878 | * When the device is started it should not have a MAC address | |
879 | * to avoid acknowledging frames before a non-monitor device | |
880 | * is added. | |
881 | * Must be implemented. | |
882 | * | |
883 | * @stop: Called after last netdevice attached to the hardware | |
884 | * is disabled. This should turn off the hardware (at least | |
885 | * it must turn off frame reception.) | |
886 | * May be called right after add_interface if that rejects | |
887 | * an interface. | |
888 | * Must be implemented. | |
889 | * | |
890 | * @add_interface: Called when a netdevice attached to the hardware is | |
891 | * enabled. Because it is not called for monitor mode devices, @open | |
892 | * and @stop must be implemented. | |
893 | * The driver should perform any initialization it needs before | |
894 | * the device can be enabled. The initial configuration for the | |
895 | * interface is given in the conf parameter. | |
896 | * The callback may refuse to add an interface by returning a | |
897 | * negative error code (which will be seen in userspace.) | |
898 | * Must be implemented. | |
899 | * | |
900 | * @remove_interface: Notifies a driver that an interface is going down. | |
901 | * The @stop callback is called after this if it is the last interface | |
902 | * and no monitor interfaces are present. | |
903 | * When all interfaces are removed, the MAC address in the hardware | |
904 | * must be cleared so the device no longer acknowledges packets, | |
905 | * the mac_addr member of the conf structure is, however, set to the | |
906 | * MAC address of the device going away. | |
907 | * Hence, this callback must be implemented. | |
908 | * | |
909 | * @config: Handler for configuration requests. IEEE 802.11 code calls this | |
910 | * function to change hardware configuration, e.g., channel. | |
911 | * | |
912 | * @config_interface: Handler for configuration requests related to interfaces | |
913 | * (e.g. BSSID changes.) | |
914 | * | |
471b3efd JB |
915 | * @bss_info_changed: Handler for configuration requests related to BSS |
916 | * parameters that may vary during BSS's lifespan, and may affect low | |
917 | * level driver (e.g. assoc/disassoc status, erp parameters). | |
918 | * This function should not be used if no BSS has been set, unless | |
919 | * for association indication. The @changed parameter indicates which | |
920 | * of the bss parameters has changed when a call is made. This callback | |
921 | * has to be atomic. | |
922 | * | |
75a5f0cc JB |
923 | * @configure_filter: Configure the device's RX filter. |
924 | * See the section "Frame filtering" for more information. | |
925 | * This callback must be implemented and atomic. | |
926 | * | |
927 | * @set_tim: Set TIM bit. If the hardware/firmware takes care of beacon | |
928 | * generation (that is, %IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE is set) | |
929 | * mac80211 calls this function when a TIM bit must be set or cleared | |
930 | * for a given AID. Must be atomic. | |
931 | * | |
932 | * @set_key: See the section "Hardware crypto acceleration" | |
933 | * This callback can sleep, and is only called between add_interface | |
934 | * and remove_interface calls, i.e. while the interface with the | |
935 | * given local_address is enabled. | |
936 | * | |
75a5f0cc | 937 | * @hw_scan: Ask the hardware to service the scan request, no need to start |
8318d78a JB |
938 | * the scan state machine in stack. The scan must honour the channel |
939 | * configuration done by the regulatory agent in the wiphy's registered | |
940 | * bands. | |
75a5f0cc JB |
941 | * |
942 | * @get_stats: return low-level statistics | |
943 | * | |
62da92fb JB |
944 | * @get_tkip_seq: If your device implements TKIP encryption in hardware this |
945 | * callback should be provided to read the TKIP transmit IVs (both IV32 | |
946 | * and IV16) for the given key from hardware. | |
75a5f0cc JB |
947 | * |
948 | * @set_rts_threshold: Configuration of RTS threshold (if device needs it) | |
949 | * | |
950 | * @set_frag_threshold: Configuration of fragmentation threshold. Assign this if | |
951 | * the device does fragmentation by itself; if this method is assigned then | |
952 | * the stack will not do fragmentation. | |
953 | * | |
954 | * @set_retry_limit: Configuration of retry limits (if device needs it) | |
955 | * | |
478f8d2b TW |
956 | * @sta_notify: Notifies low level driver about addition or removal |
957 | * of assocaited station or AP. | |
75a5f0cc | 958 | * |
75a5f0cc JB |
959 | * @conf_tx: Configure TX queue parameters (EDCF (aifs, cw_min, cw_max), |
960 | * bursting) for a hardware TX queue. The @queue parameter uses the | |
961 | * %IEEE80211_TX_QUEUE_* constants. Must be atomic. | |
962 | * | |
963 | * @get_tx_stats: Get statistics of the current TX queue status. This is used | |
964 | * to get number of currently queued packets (queue length), maximum queue | |
965 | * size (limit), and total number of packets sent using each TX queue | |
966 | * (count). This information is used for WMM to find out which TX | |
967 | * queues have room for more packets and by hostapd to provide | |
968 | * statistics about the current queueing state to external programs. | |
969 | * | |
970 | * @get_tsf: Get the current TSF timer value from firmware/hardware. Currently, | |
971 | * this is only used for IBSS mode debugging and, as such, is not a | |
972 | * required function. Must be atomic. | |
973 | * | |
974 | * @reset_tsf: Reset the TSF timer and allow firmware/hardware to synchronize | |
975 | * with other STAs in the IBSS. This is only used in IBSS mode. This | |
976 | * function is optional if the firmware/hardware takes full care of | |
977 | * TSF synchronization. | |
978 | * | |
979 | * @beacon_update: Setup beacon data for IBSS beacons. Unlike access point, | |
980 | * IBSS uses a fixed beacon frame which is configured using this | |
5ecc2a5d MB |
981 | * function. |
982 | * If the driver returns success (0) from this callback, it owns | |
983 | * the skb. That means the driver is responsible to kfree_skb() it. | |
984 | * The control structure is not dynamically allocated. That means the | |
985 | * driver does not own the pointer and if it needs it somewhere | |
986 | * outside of the context of this function, it must copy it | |
987 | * somewhere else. | |
988 | * This handler is required only for IBSS mode. | |
75a5f0cc JB |
989 | * |
990 | * @tx_last_beacon: Determine whether the last IBSS beacon was sent by us. | |
991 | * This is needed only for IBSS mode and the result of this function is | |
992 | * used to determine whether to reply to Probe Requests. | |
d3c990fb RR |
993 | * |
994 | * @conf_ht: Configures low level driver with 802.11n HT data. Must be atomic. | |
1b7d03ac RR |
995 | * |
996 | * @ampdu_action: Perform a certain A-MPDU action | |
997 | * The RA/TID combination determines the destination and TID we want | |
998 | * the ampdu action to be performed for. The action is defined through | |
999 | * ieee80211_ampdu_mlme_action. Starting sequence number (@ssn) | |
0df3ef45 RR |
1000 | * is the first frame we expect to perform the action on. notice |
1001 | * that TX/RX_STOP can pass NULL for this parameter. | |
75a5f0cc | 1002 | */ |
f0706e82 | 1003 | struct ieee80211_ops { |
f0706e82 JB |
1004 | int (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb, |
1005 | struct ieee80211_tx_control *control); | |
4150c572 | 1006 | int (*start)(struct ieee80211_hw *hw); |
4150c572 | 1007 | void (*stop)(struct ieee80211_hw *hw); |
f0706e82 JB |
1008 | int (*add_interface)(struct ieee80211_hw *hw, |
1009 | struct ieee80211_if_init_conf *conf); | |
f0706e82 JB |
1010 | void (*remove_interface)(struct ieee80211_hw *hw, |
1011 | struct ieee80211_if_init_conf *conf); | |
f0706e82 | 1012 | int (*config)(struct ieee80211_hw *hw, struct ieee80211_conf *conf); |
f0706e82 | 1013 | int (*config_interface)(struct ieee80211_hw *hw, |
32bfd35d JB |
1014 | struct ieee80211_vif *vif, |
1015 | struct ieee80211_if_conf *conf); | |
471b3efd JB |
1016 | void (*bss_info_changed)(struct ieee80211_hw *hw, |
1017 | struct ieee80211_vif *vif, | |
1018 | struct ieee80211_bss_conf *info, | |
1019 | u32 changed); | |
4150c572 JB |
1020 | void (*configure_filter)(struct ieee80211_hw *hw, |
1021 | unsigned int changed_flags, | |
1022 | unsigned int *total_flags, | |
1023 | int mc_count, struct dev_addr_list *mc_list); | |
f0706e82 | 1024 | int (*set_tim)(struct ieee80211_hw *hw, int aid, int set); |
ea49c359 | 1025 | int (*set_key)(struct ieee80211_hw *hw, enum set_key_cmd cmd, |
11a843b7 JB |
1026 | const u8 *local_address, const u8 *address, |
1027 | struct ieee80211_key_conf *key); | |
f0706e82 | 1028 | int (*hw_scan)(struct ieee80211_hw *hw, u8 *ssid, size_t len); |
f0706e82 JB |
1029 | int (*get_stats)(struct ieee80211_hw *hw, |
1030 | struct ieee80211_low_level_stats *stats); | |
62da92fb JB |
1031 | void (*get_tkip_seq)(struct ieee80211_hw *hw, u8 hw_key_idx, |
1032 | u32 *iv32, u16 *iv16); | |
f0706e82 | 1033 | int (*set_rts_threshold)(struct ieee80211_hw *hw, u32 value); |
f0706e82 | 1034 | int (*set_frag_threshold)(struct ieee80211_hw *hw, u32 value); |
f0706e82 JB |
1035 | int (*set_retry_limit)(struct ieee80211_hw *hw, |
1036 | u32 short_retry, u32 long_retr); | |
32bfd35d | 1037 | void (*sta_notify)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, |
478f8d2b | 1038 | enum sta_notify_cmd, const u8 *addr); |
f0706e82 JB |
1039 | int (*conf_tx)(struct ieee80211_hw *hw, int queue, |
1040 | const struct ieee80211_tx_queue_params *params); | |
f0706e82 JB |
1041 | int (*get_tx_stats)(struct ieee80211_hw *hw, |
1042 | struct ieee80211_tx_queue_stats *stats); | |
f0706e82 | 1043 | u64 (*get_tsf)(struct ieee80211_hw *hw); |
f0706e82 | 1044 | void (*reset_tsf)(struct ieee80211_hw *hw); |
f0706e82 JB |
1045 | int (*beacon_update)(struct ieee80211_hw *hw, |
1046 | struct sk_buff *skb, | |
1047 | struct ieee80211_tx_control *control); | |
f0706e82 | 1048 | int (*tx_last_beacon)(struct ieee80211_hw *hw); |
d3c990fb | 1049 | int (*conf_ht)(struct ieee80211_hw *hw, struct ieee80211_conf *conf); |
1b7d03ac RR |
1050 | int (*ampdu_action)(struct ieee80211_hw *hw, |
1051 | enum ieee80211_ampdu_mlme_action action, | |
0df3ef45 | 1052 | const u8 *addr, u16 tid, u16 *ssn); |
f0706e82 JB |
1053 | }; |
1054 | ||
75a5f0cc JB |
1055 | /** |
1056 | * ieee80211_alloc_hw - Allocate a new hardware device | |
1057 | * | |
1058 | * This must be called once for each hardware device. The returned pointer | |
1059 | * must be used to refer to this device when calling other functions. | |
1060 | * mac80211 allocates a private data area for the driver pointed to by | |
1061 | * @priv in &struct ieee80211_hw, the size of this area is given as | |
1062 | * @priv_data_len. | |
1063 | * | |
1064 | * @priv_data_len: length of private data | |
1065 | * @ops: callbacks for this device | |
f0706e82 JB |
1066 | */ |
1067 | struct ieee80211_hw *ieee80211_alloc_hw(size_t priv_data_len, | |
1068 | const struct ieee80211_ops *ops); | |
1069 | ||
75a5f0cc JB |
1070 | /** |
1071 | * ieee80211_register_hw - Register hardware device | |
1072 | * | |
1073 | * You must call this function before any other functions | |
1074 | * except ieee80211_register_hwmode. | |
1075 | * | |
1076 | * @hw: the device to register as returned by ieee80211_alloc_hw() | |
1077 | */ | |
f0706e82 JB |
1078 | int ieee80211_register_hw(struct ieee80211_hw *hw); |
1079 | ||
f0706e82 JB |
1080 | #ifdef CONFIG_MAC80211_LEDS |
1081 | extern char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw); | |
1082 | extern char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw); | |
47f0c502 | 1083 | extern char *__ieee80211_get_assoc_led_name(struct ieee80211_hw *hw); |
cdcb006f | 1084 | extern char *__ieee80211_get_radio_led_name(struct ieee80211_hw *hw); |
f0706e82 | 1085 | #endif |
75a5f0cc JB |
1086 | /** |
1087 | * ieee80211_get_tx_led_name - get name of TX LED | |
1088 | * | |
1089 | * mac80211 creates a transmit LED trigger for each wireless hardware | |
1090 | * that can be used to drive LEDs if your driver registers a LED device. | |
1091 | * This function returns the name (or %NULL if not configured for LEDs) | |
1092 | * of the trigger so you can automatically link the LED device. | |
1093 | * | |
1094 | * @hw: the hardware to get the LED trigger name for | |
1095 | */ | |
f0706e82 JB |
1096 | static inline char *ieee80211_get_tx_led_name(struct ieee80211_hw *hw) |
1097 | { | |
1098 | #ifdef CONFIG_MAC80211_LEDS | |
1099 | return __ieee80211_get_tx_led_name(hw); | |
1100 | #else | |
1101 | return NULL; | |
1102 | #endif | |
1103 | } | |
1104 | ||
75a5f0cc JB |
1105 | /** |
1106 | * ieee80211_get_rx_led_name - get name of RX LED | |
1107 | * | |
1108 | * mac80211 creates a receive LED trigger for each wireless hardware | |
1109 | * that can be used to drive LEDs if your driver registers a LED device. | |
1110 | * This function returns the name (or %NULL if not configured for LEDs) | |
1111 | * of the trigger so you can automatically link the LED device. | |
1112 | * | |
1113 | * @hw: the hardware to get the LED trigger name for | |
1114 | */ | |
f0706e82 JB |
1115 | static inline char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw) |
1116 | { | |
1117 | #ifdef CONFIG_MAC80211_LEDS | |
1118 | return __ieee80211_get_rx_led_name(hw); | |
1119 | #else | |
1120 | return NULL; | |
1121 | #endif | |
1122 | } | |
1123 | ||
cdcb006f ID |
1124 | /** |
1125 | * ieee80211_get_assoc_led_name - get name of association LED | |
1126 | * | |
1127 | * mac80211 creates a association LED trigger for each wireless hardware | |
1128 | * that can be used to drive LEDs if your driver registers a LED device. | |
1129 | * This function returns the name (or %NULL if not configured for LEDs) | |
1130 | * of the trigger so you can automatically link the LED device. | |
1131 | * | |
1132 | * @hw: the hardware to get the LED trigger name for | |
1133 | */ | |
47f0c502 MB |
1134 | static inline char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw) |
1135 | { | |
1136 | #ifdef CONFIG_MAC80211_LEDS | |
1137 | return __ieee80211_get_assoc_led_name(hw); | |
1138 | #else | |
1139 | return NULL; | |
1140 | #endif | |
1141 | } | |
1142 | ||
cdcb006f ID |
1143 | /** |
1144 | * ieee80211_get_radio_led_name - get name of radio LED | |
1145 | * | |
1146 | * mac80211 creates a radio change LED trigger for each wireless hardware | |
1147 | * that can be used to drive LEDs if your driver registers a LED device. | |
1148 | * This function returns the name (or %NULL if not configured for LEDs) | |
1149 | * of the trigger so you can automatically link the LED device. | |
1150 | * | |
1151 | * @hw: the hardware to get the LED trigger name for | |
1152 | */ | |
1153 | static inline char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw) | |
1154 | { | |
1155 | #ifdef CONFIG_MAC80211_LEDS | |
1156 | return __ieee80211_get_radio_led_name(hw); | |
1157 | #else | |
1158 | return NULL; | |
1159 | #endif | |
1160 | } | |
47f0c502 | 1161 | |
75a5f0cc JB |
1162 | /** |
1163 | * ieee80211_unregister_hw - Unregister a hardware device | |
1164 | * | |
1165 | * This function instructs mac80211 to free allocated resources | |
1166 | * and unregister netdevices from the networking subsystem. | |
1167 | * | |
1168 | * @hw: the hardware to unregister | |
1169 | */ | |
f0706e82 JB |
1170 | void ieee80211_unregister_hw(struct ieee80211_hw *hw); |
1171 | ||
75a5f0cc JB |
1172 | /** |
1173 | * ieee80211_free_hw - free hardware descriptor | |
1174 | * | |
1175 | * This function frees everything that was allocated, including the | |
1176 | * private data for the driver. You must call ieee80211_unregister_hw() | |
1177 | * before calling this function | |
1178 | * | |
1179 | * @hw: the hardware to free | |
1180 | */ | |
f0706e82 JB |
1181 | void ieee80211_free_hw(struct ieee80211_hw *hw); |
1182 | ||
75a5f0cc | 1183 | /* trick to avoid symbol clashes with the ieee80211 subsystem */ |
f0706e82 JB |
1184 | void __ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb, |
1185 | struct ieee80211_rx_status *status); | |
75a5f0cc JB |
1186 | |
1187 | /** | |
1188 | * ieee80211_rx - receive frame | |
1189 | * | |
1190 | * Use this function to hand received frames to mac80211. The receive | |
1191 | * buffer in @skb must start with an IEEE 802.11 header or a radiotap | |
1192 | * header if %RX_FLAG_RADIOTAP is set in the @status flags. | |
1193 | * | |
1194 | * This function may not be called in IRQ context. | |
1195 | * | |
1196 | * @hw: the hardware this frame came in on | |
1197 | * @skb: the buffer to receive, owned by mac80211 after this call | |
1198 | * @status: status of this frame; the status pointer need not be valid | |
1199 | * after this function returns | |
1200 | */ | |
1201 | static inline void ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb, | |
1202 | struct ieee80211_rx_status *status) | |
1203 | { | |
1204 | __ieee80211_rx(hw, skb, status); | |
1205 | } | |
1206 | ||
1207 | /** | |
1208 | * ieee80211_rx_irqsafe - receive frame | |
1209 | * | |
1210 | * Like ieee80211_rx() but can be called in IRQ context | |
1211 | * (internally defers to a workqueue.) | |
1212 | * | |
1213 | * @hw: the hardware this frame came in on | |
1214 | * @skb: the buffer to receive, owned by mac80211 after this call | |
1215 | * @status: status of this frame; the status pointer need not be valid | |
1216 | * after this function returns and is not freed by mac80211, | |
1217 | * it is recommended that it points to a stack area | |
1218 | */ | |
f0706e82 JB |
1219 | void ieee80211_rx_irqsafe(struct ieee80211_hw *hw, |
1220 | struct sk_buff *skb, | |
1221 | struct ieee80211_rx_status *status); | |
1222 | ||
75a5f0cc JB |
1223 | /** |
1224 | * ieee80211_tx_status - transmit status callback | |
1225 | * | |
1226 | * Call this function for all transmitted frames after they have been | |
1227 | * transmitted. It is permissible to not call this function for | |
1228 | * multicast frames but this can affect statistics. | |
1229 | * | |
1230 | * @hw: the hardware the frame was transmitted by | |
1231 | * @skb: the frame that was transmitted, owned by mac80211 after this call | |
1232 | * @status: status information for this frame; the status pointer need not | |
1233 | * be valid after this function returns and is not freed by mac80211, | |
1234 | * it is recommended that it points to a stack area | |
1235 | */ | |
f0706e82 JB |
1236 | void ieee80211_tx_status(struct ieee80211_hw *hw, |
1237 | struct sk_buff *skb, | |
1238 | struct ieee80211_tx_status *status); | |
1239 | void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw, | |
1240 | struct sk_buff *skb, | |
1241 | struct ieee80211_tx_status *status); | |
1242 | ||
1243 | /** | |
1244 | * ieee80211_beacon_get - beacon generation function | |
1245 | * @hw: pointer obtained from ieee80211_alloc_hw(). | |
32bfd35d | 1246 | * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf. |
f0706e82 JB |
1247 | * @control: will be filled with information needed to send this beacon. |
1248 | * | |
1249 | * If the beacon frames are generated by the host system (i.e., not in | |
1250 | * hardware/firmware), the low-level driver uses this function to receive | |
1251 | * the next beacon frame from the 802.11 code. The low-level is responsible | |
1252 | * for calling this function before beacon data is needed (e.g., based on | |
1253 | * hardware interrupt). Returned skb is used only once and low-level driver | |
1254 | * is responsible of freeing it. | |
1255 | */ | |
1256 | struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw, | |
32bfd35d | 1257 | struct ieee80211_vif *vif, |
f0706e82 JB |
1258 | struct ieee80211_tx_control *control); |
1259 | ||
1260 | /** | |
1261 | * ieee80211_rts_get - RTS frame generation function | |
1262 | * @hw: pointer obtained from ieee80211_alloc_hw(). | |
32bfd35d | 1263 | * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf. |
f0706e82 JB |
1264 | * @frame: pointer to the frame that is going to be protected by the RTS. |
1265 | * @frame_len: the frame length (in octets). | |
1266 | * @frame_txctl: &struct ieee80211_tx_control of the frame. | |
1267 | * @rts: The buffer where to store the RTS frame. | |
1268 | * | |
1269 | * If the RTS frames are generated by the host system (i.e., not in | |
1270 | * hardware/firmware), the low-level driver uses this function to receive | |
1271 | * the next RTS frame from the 802.11 code. The low-level is responsible | |
1272 | * for calling this function before and RTS frame is needed. | |
1273 | */ | |
32bfd35d | 1274 | void ieee80211_rts_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif, |
f0706e82 JB |
1275 | const void *frame, size_t frame_len, |
1276 | const struct ieee80211_tx_control *frame_txctl, | |
1277 | struct ieee80211_rts *rts); | |
1278 | ||
1279 | /** | |
1280 | * ieee80211_rts_duration - Get the duration field for an RTS frame | |
1281 | * @hw: pointer obtained from ieee80211_alloc_hw(). | |
32bfd35d | 1282 | * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf. |
f0706e82 JB |
1283 | * @frame_len: the length of the frame that is going to be protected by the RTS. |
1284 | * @frame_txctl: &struct ieee80211_tx_control of the frame. | |
1285 | * | |
1286 | * If the RTS is generated in firmware, but the host system must provide | |
1287 | * the duration field, the low-level driver uses this function to receive | |
1288 | * the duration field value in little-endian byteorder. | |
1289 | */ | |
32bfd35d JB |
1290 | __le16 ieee80211_rts_duration(struct ieee80211_hw *hw, |
1291 | struct ieee80211_vif *vif, size_t frame_len, | |
f0706e82 JB |
1292 | const struct ieee80211_tx_control *frame_txctl); |
1293 | ||
1294 | /** | |
1295 | * ieee80211_ctstoself_get - CTS-to-self frame generation function | |
1296 | * @hw: pointer obtained from ieee80211_alloc_hw(). | |
32bfd35d | 1297 | * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf. |
f0706e82 JB |
1298 | * @frame: pointer to the frame that is going to be protected by the CTS-to-self. |
1299 | * @frame_len: the frame length (in octets). | |
1300 | * @frame_txctl: &struct ieee80211_tx_control of the frame. | |
1301 | * @cts: The buffer where to store the CTS-to-self frame. | |
1302 | * | |
1303 | * If the CTS-to-self frames are generated by the host system (i.e., not in | |
1304 | * hardware/firmware), the low-level driver uses this function to receive | |
1305 | * the next CTS-to-self frame from the 802.11 code. The low-level is responsible | |
1306 | * for calling this function before and CTS-to-self frame is needed. | |
1307 | */ | |
32bfd35d JB |
1308 | void ieee80211_ctstoself_get(struct ieee80211_hw *hw, |
1309 | struct ieee80211_vif *vif, | |
f0706e82 JB |
1310 | const void *frame, size_t frame_len, |
1311 | const struct ieee80211_tx_control *frame_txctl, | |
1312 | struct ieee80211_cts *cts); | |
1313 | ||
1314 | /** | |
1315 | * ieee80211_ctstoself_duration - Get the duration field for a CTS-to-self frame | |
1316 | * @hw: pointer obtained from ieee80211_alloc_hw(). | |
32bfd35d | 1317 | * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf. |
f0706e82 JB |
1318 | * @frame_len: the length of the frame that is going to be protected by the CTS-to-self. |
1319 | * @frame_txctl: &struct ieee80211_tx_control of the frame. | |
1320 | * | |
1321 | * If the CTS-to-self is generated in firmware, but the host system must provide | |
1322 | * the duration field, the low-level driver uses this function to receive | |
1323 | * the duration field value in little-endian byteorder. | |
1324 | */ | |
32bfd35d JB |
1325 | __le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw, |
1326 | struct ieee80211_vif *vif, | |
f0706e82 JB |
1327 | size_t frame_len, |
1328 | const struct ieee80211_tx_control *frame_txctl); | |
1329 | ||
1330 | /** | |
1331 | * ieee80211_generic_frame_duration - Calculate the duration field for a frame | |
1332 | * @hw: pointer obtained from ieee80211_alloc_hw(). | |
32bfd35d | 1333 | * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf. |
f0706e82 | 1334 | * @frame_len: the length of the frame. |
8318d78a | 1335 | * @rate: the rate at which the frame is going to be transmitted. |
f0706e82 JB |
1336 | * |
1337 | * Calculate the duration field of some generic frame, given its | |
1338 | * length and transmission rate (in 100kbps). | |
1339 | */ | |
32bfd35d JB |
1340 | __le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw, |
1341 | struct ieee80211_vif *vif, | |
f0706e82 | 1342 | size_t frame_len, |
8318d78a | 1343 | struct ieee80211_rate *rate); |
f0706e82 JB |
1344 | |
1345 | /** | |
1346 | * ieee80211_get_buffered_bc - accessing buffered broadcast and multicast frames | |
1347 | * @hw: pointer as obtained from ieee80211_alloc_hw(). | |
32bfd35d | 1348 | * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf. |
f0706e82 JB |
1349 | * @control: will be filled with information needed to send returned frame. |
1350 | * | |
1351 | * Function for accessing buffered broadcast and multicast frames. If | |
1352 | * hardware/firmware does not implement buffering of broadcast/multicast | |
1353 | * frames when power saving is used, 802.11 code buffers them in the host | |
1354 | * memory. The low-level driver uses this function to fetch next buffered | |
1355 | * frame. In most cases, this is used when generating beacon frame. This | |
1356 | * function returns a pointer to the next buffered skb or NULL if no more | |
1357 | * buffered frames are available. | |
1358 | * | |
1359 | * Note: buffered frames are returned only after DTIM beacon frame was | |
1360 | * generated with ieee80211_beacon_get() and the low-level driver must thus | |
1361 | * call ieee80211_beacon_get() first. ieee80211_get_buffered_bc() returns | |
1362 | * NULL if the previous generated beacon was not DTIM, so the low-level driver | |
1363 | * does not need to check for DTIM beacons separately and should be able to | |
1364 | * use common code for all beacons. | |
1365 | */ | |
1366 | struct sk_buff * | |
32bfd35d | 1367 | ieee80211_get_buffered_bc(struct ieee80211_hw *hw, struct ieee80211_vif *vif, |
f0706e82 JB |
1368 | struct ieee80211_tx_control *control); |
1369 | ||
75a5f0cc JB |
1370 | /** |
1371 | * ieee80211_get_hdrlen_from_skb - get header length from data | |
1372 | * | |
1373 | * Given an skb with a raw 802.11 header at the data pointer this function | |
f0706e82 JB |
1374 | * returns the 802.11 header length in bytes (not including encryption |
1375 | * headers). If the data in the sk_buff is too short to contain a valid 802.11 | |
1376 | * header the function returns 0. | |
75a5f0cc JB |
1377 | * |
1378 | * @skb: the frame | |
f0706e82 JB |
1379 | */ |
1380 | int ieee80211_get_hdrlen_from_skb(const struct sk_buff *skb); | |
1381 | ||
75a5f0cc JB |
1382 | /** |
1383 | * ieee80211_get_hdrlen - get header length from frame control | |
1384 | * | |
1385 | * This function returns the 802.11 header length in bytes (not including | |
1386 | * encryption headers.) | |
1387 | * | |
1388 | * @fc: the frame control field (in CPU endianness) | |
1389 | */ | |
f0706e82 JB |
1390 | int ieee80211_get_hdrlen(u16 fc); |
1391 | ||
1392 | /** | |
1393 | * ieee80211_wake_queue - wake specific queue | |
1394 | * @hw: pointer as obtained from ieee80211_alloc_hw(). | |
1395 | * @queue: queue number (counted from zero). | |
1396 | * | |
1397 | * Drivers should use this function instead of netif_wake_queue. | |
1398 | */ | |
1399 | void ieee80211_wake_queue(struct ieee80211_hw *hw, int queue); | |
1400 | ||
1401 | /** | |
1402 | * ieee80211_stop_queue - stop specific queue | |
1403 | * @hw: pointer as obtained from ieee80211_alloc_hw(). | |
1404 | * @queue: queue number (counted from zero). | |
1405 | * | |
1406 | * Drivers should use this function instead of netif_stop_queue. | |
1407 | */ | |
1408 | void ieee80211_stop_queue(struct ieee80211_hw *hw, int queue); | |
1409 | ||
1410 | /** | |
1411 | * ieee80211_start_queues - start all queues | |
1412 | * @hw: pointer to as obtained from ieee80211_alloc_hw(). | |
1413 | * | |
1414 | * Drivers should use this function instead of netif_start_queue. | |
1415 | */ | |
1416 | void ieee80211_start_queues(struct ieee80211_hw *hw); | |
1417 | ||
1418 | /** | |
1419 | * ieee80211_stop_queues - stop all queues | |
1420 | * @hw: pointer as obtained from ieee80211_alloc_hw(). | |
1421 | * | |
1422 | * Drivers should use this function instead of netif_stop_queue. | |
1423 | */ | |
1424 | void ieee80211_stop_queues(struct ieee80211_hw *hw); | |
1425 | ||
1426 | /** | |
1427 | * ieee80211_wake_queues - wake all queues | |
1428 | * @hw: pointer as obtained from ieee80211_alloc_hw(). | |
1429 | * | |
1430 | * Drivers should use this function instead of netif_wake_queue. | |
1431 | */ | |
1432 | void ieee80211_wake_queues(struct ieee80211_hw *hw); | |
1433 | ||
75a5f0cc JB |
1434 | /** |
1435 | * ieee80211_scan_completed - completed hardware scan | |
1436 | * | |
1437 | * When hardware scan offload is used (i.e. the hw_scan() callback is | |
1438 | * assigned) this function needs to be called by the driver to notify | |
1439 | * mac80211 that the scan finished. | |
1440 | * | |
1441 | * @hw: the hardware that finished the scan | |
1442 | */ | |
f0706e82 JB |
1443 | void ieee80211_scan_completed(struct ieee80211_hw *hw); |
1444 | ||
dabeb344 JB |
1445 | /** |
1446 | * ieee80211_iterate_active_interfaces - iterate active interfaces | |
1447 | * | |
1448 | * This function iterates over the interfaces associated with a given | |
1449 | * hardware that are currently active and calls the callback for them. | |
dabeb344 JB |
1450 | * |
1451 | * @hw: the hardware struct of which the interfaces should be iterated over | |
e38bad47 | 1452 | * @iterator: the iterator function to call, cannot sleep |
dabeb344 JB |
1453 | * @data: first argument of the iterator function |
1454 | */ | |
1455 | void ieee80211_iterate_active_interfaces(struct ieee80211_hw *hw, | |
1456 | void (*iterator)(void *data, u8 *mac, | |
32bfd35d | 1457 | struct ieee80211_vif *vif), |
dabeb344 JB |
1458 | void *data); |
1459 | ||
0df3ef45 RR |
1460 | /** |
1461 | * ieee80211_start_tx_ba_session - Start a tx Block Ack session. | |
1462 | * @hw: pointer as obtained from ieee80211_alloc_hw(). | |
1463 | * @ra: receiver address of the BA session recipient | |
1464 | * @tid: the TID to BA on. | |
1465 | * @return: success if addBA request was sent, failure otherwise | |
1466 | * | |
1467 | * Although mac80211/low level driver/user space application can estimate | |
1468 | * the need to start aggregation on a certain RA/TID, the session level | |
1469 | * will be managed by the mac80211. | |
1470 | */ | |
1471 | int ieee80211_start_tx_ba_session(struct ieee80211_hw *hw, u8 *ra, u16 tid); | |
1472 | ||
1473 | /** | |
1474 | * ieee80211_start_tx_ba_cb - low level driver ready to aggregate. | |
1475 | * @hw: pointer as obtained from ieee80211_alloc_hw(). | |
1476 | * @ra: receiver address of the BA session recipient. | |
1477 | * @tid: the TID to BA on. | |
1478 | * | |
1479 | * This function must be called by low level driver once it has | |
1480 | * finished with preparations for the BA session. | |
1481 | */ | |
1482 | void ieee80211_start_tx_ba_cb(struct ieee80211_hw *hw, u8 *ra, u16 tid); | |
1483 | ||
1484 | /** | |
1485 | * ieee80211_start_tx_ba_cb_irqsafe - low level driver ready to aggregate. | |
1486 | * @hw: pointer as obtained from ieee80211_alloc_hw(). | |
1487 | * @ra: receiver address of the BA session recipient. | |
1488 | * @tid: the TID to BA on. | |
1489 | * | |
1490 | * This function must be called by low level driver once it has | |
1491 | * finished with preparations for the BA session. | |
1492 | * This version of the function is irq safe. | |
1493 | */ | |
1494 | void ieee80211_start_tx_ba_cb_irqsafe(struct ieee80211_hw *hw, const u8 *ra, | |
1495 | u16 tid); | |
1496 | ||
1497 | /** | |
1498 | * ieee80211_stop_tx_ba_session - Stop a Block Ack session. | |
1499 | * @hw: pointer as obtained from ieee80211_alloc_hw(). | |
1500 | * @ra: receiver address of the BA session recipient | |
1501 | * @tid: the TID to stop BA. | |
1502 | * @initiator: if indicates initiator DELBA frame will be sent. | |
1503 | * @return: error if no sta with matching da found, success otherwise | |
1504 | * | |
1505 | * Although mac80211/low level driver/user space application can estimate | |
1506 | * the need to stop aggregation on a certain RA/TID, the session level | |
1507 | * will be managed by the mac80211. | |
1508 | */ | |
1509 | int ieee80211_stop_tx_ba_session(struct ieee80211_hw *hw, | |
1510 | u8 *ra, u16 tid, | |
1511 | enum ieee80211_back_parties initiator); | |
1512 | ||
1513 | /** | |
1514 | * ieee80211_stop_tx_ba_cb - low level driver ready to stop aggregate. | |
1515 | * @hw: pointer as obtained from ieee80211_alloc_hw(). | |
1516 | * @ra: receiver address of the BA session recipient. | |
1517 | * @tid: the desired TID to BA on. | |
1518 | * | |
1519 | * This function must be called by low level driver once it has | |
1520 | * finished with preparations for the BA session tear down. | |
1521 | */ | |
1522 | void ieee80211_stop_tx_ba_cb(struct ieee80211_hw *hw, u8 *ra, u8 tid); | |
1523 | ||
1524 | /** | |
1525 | * ieee80211_stop_tx_ba_cb_irqsafe - low level driver ready to stop aggregate. | |
1526 | * @hw: pointer as obtained from ieee80211_alloc_hw(). | |
1527 | * @ra: receiver address of the BA session recipient. | |
1528 | * @tid: the desired TID to BA on. | |
1529 | * | |
1530 | * This function must be called by low level driver once it has | |
1531 | * finished with preparations for the BA session tear down. | |
1532 | * This version of the function is irq safe. | |
1533 | */ | |
1534 | void ieee80211_stop_tx_ba_cb_irqsafe(struct ieee80211_hw *hw, const u8 *ra, | |
1535 | u16 tid); | |
1536 | ||
f0706e82 | 1537 | #endif /* MAC80211_H */ |