| 1 | /* |
| 2 | * at91sam9x5cm.dtsi - Device Tree Include file for AT91SAM9x5 CPU Module |
| 3 | * |
| 4 | * Copyright (C) 2012 Atmel, |
| 5 | * 2012 Nicolas Ferre <nicolas.ferre@atmel.com> |
| 6 | * |
| 7 | * Licensed under GPLv2 or later. |
| 8 | */ |
| 9 | |
| 10 | / { |
| 11 | memory { |
| 12 | reg = <0x20000000 0x8000000>; |
| 13 | }; |
| 14 | |
| 15 | clocks { |
| 16 | #address-cells = <1>; |
| 17 | #size-cells = <1>; |
| 18 | ranges; |
| 19 | |
| 20 | main_clock: clock@0 { |
| 21 | compatible = "atmel,osc", "fixed-clock"; |
| 22 | clock-frequency = <12000000>; |
| 23 | }; |
| 24 | }; |
| 25 | |
| 26 | clocks { |
| 27 | slow_xtal { |
| 28 | clock-frequency = <32768>; |
| 29 | }; |
| 30 | |
| 31 | main_xtal { |
| 32 | clock-frequency = <12000000>; |
| 33 | }; |
| 34 | }; |
| 35 | |
| 36 | ahb { |
| 37 | apb { |
| 38 | pinctrl@fffff400 { |
| 39 | 1wire_cm { |
| 40 | pinctrl_1wire_cm: 1wire_cm-0 { |
| 41 | atmel,pins = <AT91_PIOB 18 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>; /* PB18 multidrive, conflicts with led */ |
| 42 | }; |
| 43 | }; |
| 44 | }; |
| 45 | |
| 46 | rtc@fffffeb0 { |
| 47 | status = "okay"; |
| 48 | }; |
| 49 | }; |
| 50 | |
| 51 | nand0: nand@40000000 { |
| 52 | nand-bus-width = <8>; |
| 53 | nand-ecc-mode = "hw"; |
| 54 | atmel,has-pmecc; /* Enable PMECC */ |
| 55 | atmel,pmecc-cap = <2>; |
| 56 | atmel,pmecc-sector-size = <512>; |
| 57 | nand-on-flash-bbt; |
| 58 | status = "okay"; |
| 59 | |
| 60 | at91bootstrap@0 { |
| 61 | label = "at91bootstrap"; |
| 62 | reg = <0x0 0x40000>; |
| 63 | }; |
| 64 | |
| 65 | uboot@40000 { |
| 66 | label = "u-boot"; |
| 67 | reg = <0x40000 0x80000>; |
| 68 | }; |
| 69 | |
| 70 | ubootenv@c0000 { |
| 71 | label = "U-Boot Env"; |
| 72 | reg = <0xc0000 0x140000>; |
| 73 | }; |
| 74 | |
| 75 | kernel@200000 { |
| 76 | label = "kernel"; |
| 77 | reg = <0x200000 0x600000>; |
| 78 | }; |
| 79 | |
| 80 | rootfs@800000 { |
| 81 | label = "rootfs"; |
| 82 | reg = <0x800000 0x1f800000>; |
| 83 | }; |
| 84 | }; |
| 85 | }; |
| 86 | |
| 87 | leds { |
| 88 | compatible = "gpio-leds"; |
| 89 | |
| 90 | pb18 { |
| 91 | label = "pb18"; |
| 92 | gpios = <&pioB 18 GPIO_ACTIVE_LOW>; |
| 93 | linux,default-trigger = "heartbeat"; |
| 94 | }; |
| 95 | |
| 96 | pd21 { |
| 97 | label = "pd21"; |
| 98 | gpios = <&pioD 21 GPIO_ACTIVE_HIGH>; |
| 99 | }; |
| 100 | }; |
| 101 | |
| 102 | 1wire_cm { |
| 103 | compatible = "w1-gpio"; |
| 104 | gpios = <&pioB 18 GPIO_ACTIVE_HIGH>; |
| 105 | linux,open-drain; |
| 106 | pinctrl-names = "default"; |
| 107 | pinctrl-0 = <&pinctrl_1wire_cm>; |
| 108 | status = "okay"; |
| 109 | }; |
| 110 | |
| 111 | }; |