2 Advanced Linux Sound Architecture - Driver
3 ==========================================
10 To enable ALSA support you need at least to build the kernel with
11 primary sound card support (CONFIG_SOUND). Since ALSA can emulate OSS,
12 you don't have to choose any of the OSS modules.
14 Enable "OSS API emulation" (CONFIG_SND_OSSEMUL) and both OSS mixer and
15 PCM supports if you want to run OSS applications with ALSA.
17 If you want to support the WaveTable functionality on cards such as
18 SB Live! then you need to enable "Sequencer support"
19 (CONFIG_SND_SEQUENCER).
21 To make ALSA debug messages more verbose, enable the "Verbose printk"
22 and "Debug" options. To check for memory leaks, turn on "Debug memory"
23 too. "Debug detection" will add checks for the detection of cards.
25 Please note that all the ALSA ISA drivers support the Linux isapnp API
26 (if the card supports ISA PnP). You don't need to configure the cards
33 This depends on your distribution, but normally you use the /dev/MAKEDEV
34 script to create the necessary device nodes. On some systems you use a
35 script named 'snddevices'.
41 The user can load modules with options. If the module supports more than
42 one card and you have more than one card of the same type then you can
43 specify multiple values for the option separated by commas.
45 Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
50 The core ALSA module. It is used by all ALSA card drivers.
51 It takes the following options which have global effects.
53 major - major number for sound driver
56 - limiting card index for auto-loading (1-8)
58 - For auto-loading more than one card, specify this
59 option together with snd-card-X aliases.
61 - permission mask for dynamic sound device filesystem
62 - This is available only when DEVFS is enabled
64 - E.g.: device_mode=0660
70 The PCM OSS emulation module.
71 This module takes options which change the mapping of devices.
73 dsp_map - PCM device number maps assigned to the 1st OSS device.
75 adsp_map - PCM device number maps assigned to the 2st OSS device.
78 - Don't block opening busy PCM devices. Default: 1
80 For example, when dsp_map=2, /dev/dsp will be mapped to PCM #2 of
81 the card #0. Similarly, when adsp_map=0, /dev/adsp will be mapped
82 to PCM #0 of the card #0.
83 For changing the second or later card, specify the option with
84 commas, such like "dsp_map=0,1".
86 nonblock_open option is used to change the behavior of the PCM
87 regarding opening the device. When this option is non-zero,
88 opening a busy OSS PCM device won't be blocked but return
89 immediately with EAGAIN (just like O_NONBLOCK flag).
94 This module takes options which change the mapping of devices.
95 similar to those of the snd-pcm-oss module.
97 midi_map - MIDI device number maps assigned to the 1st OSS device.
99 amidi_map - MIDI device number maps assigned to the 2st OSS device.
102 Common parameters for top sound card modules
103 --------------------------------------------
105 Each of top level sound card module takes the following options.
107 index - index (slot #) of sound card
108 - Values: 0 through 31 or negative
109 - If nonnegative, assign that index number
110 - if negative, interpret as a bitmask of permissible
111 indices; the first free permitted index is assigned
113 id - card ID (identifier or name)
114 - Can be up to 15 characters long
115 - Default: the card type
116 - A directory by this name is created under /proc/asound/
117 containing information about the card
118 - This ID can be used instead of the index number in
121 - Default: enabled, for PCI and ISA PnP cards
126 Module for sound cards based on Analog Devices AD1816A/AD1815 ISA chips.
128 port - port # for AD1816A chip (PnP setup)
129 mpu_port - port # for MPU-401 UART (PnP setup)
130 fm_port - port # for OPL3 (PnP setup)
131 irq - IRQ # for AD1816A chip (PnP setup)
132 mpu_irq - IRQ # for MPU-401 UART (PnP setup)
133 dma1 - first DMA # for AD1816A chip (PnP setup)
134 dma2 - second DMA # for AD1816A chip (PnP setup)
135 clockfreq - Clock frequency for AD1816A chip (default = 0, 33000Hz)
137 This module supports multiple cards, autoprobe and PnP.
142 Module for sound cards based on AD1848/AD1847/CS4248 ISA chips.
144 port - port # for AD1848 chip
145 irq - IRQ # for AD1848 chip
146 dma1 - DMA # for AD1848 chip (0,1,3)
148 This module supports multiple cards. It does not support autoprobe
149 thus main port must be specified!!! Other ports are optional.
151 The power-management is supported.
156 Module for Analog Devices AD1889 chips.
158 ac97_quirk - AC'97 workaround for strange hardware
159 See the description of intel8x0 module for details.
161 This module supports multiple cards.
166 Module for ALi M5451 PCI chip.
168 pcm_channels - Number of hardware channels assigned for PCM
169 spdif - Support SPDIF I/O
172 This module supports one chip and autoprobe.
174 The power-management is supported.
179 Module for sound cards based on Avance Logic ALS100/ALS120 ISA chips.
181 port - port # for ALS100 (SB16) chip (PnP setup)
182 irq - IRQ # for ALS100 (SB16) chip (PnP setup)
183 dma8 - 8-bit DMA # for ALS100 (SB16) chip (PnP setup)
184 dma16 - 16-bit DMA # for ALS100 (SB16) chip (PnP setup)
185 mpu_port - port # for MPU-401 UART (PnP setup)
186 mpu_irq - IRQ # for MPU-401 (PnP setup)
187 fm_port - port # for OPL3 FM (PnP setup)
189 This module supports multiple cards, autoprobe and PnP.
191 The power-management is supported.
196 Module for sound cards based on Avance Logic ALS4000 PCI chip.
198 joystick_port - port # for legacy joystick support.
199 0 = disabled (default), 1 = auto-detect
201 This module supports multiple cards, autoprobe and PnP.
203 The power-management is supported.
208 Module for ATI IXP 150/200/250/400 AC97 controllers.
210 ac97_clock - AC'97 clock (default = 48000)
211 ac97_quirk - AC'97 workaround for strange hardware
212 See "AC97 Quirk Option" section below.
213 spdif_aclink - S/PDIF transfer over AC-link (default = 1)
215 This module supports one card and autoprobe.
217 ATI IXP has two different methods to control SPDIF output. One is
218 over AC-link and another is over the "direct" SPDIF output. The
219 implementation depends on the motherboard, and you'll need to
220 choose the correct one via spdif_aclink module option.
222 The power-management is supported.
224 Module snd-atiixp-modem
225 -----------------------
227 Module for ATI IXP 150/200/250 AC97 modem controllers.
229 This module supports one card and autoprobe.
231 Note: The default index value of this module is -2, i.e. the first
234 The power-management is supported.
236 Module snd-au8810, snd-au8820, snd-au8830
237 -----------------------------------------
239 Module for Aureal Vortex, Vortex2 and Advantage device.
241 pcifix - Control PCI workarounds
242 0 = Disable all workarounds
243 1 = Force the PCI latency of the Aureal card to 0xff
244 2 = Force the Extend PCI#2 Internal Master for Efficient
245 Handling of Dummy Requests on the VIA KT133 AGP Bridge
246 3 = Force both settings
247 255 = Autodetect what is required (default)
249 This module supports all ADB PCM channels, ac97 mixer, SPDIF, hardware
250 EQ, mpu401, gameport. A3D and wavetable support are still in development.
251 Development and reverse engineering work is being coordinated at
252 http://savannah.nongnu.org/projects/openvortex/
253 SPDIF output has a copy of the AC97 codec output, unless you use the
254 "spdif" pcm device, which allows raw data passthru.
255 The hardware EQ hardware and SPDIF is only present in the Vortex2 and
258 Note: Some ALSA mixer applications don't handle the SPDIF sample rate
259 control correctly. If you have problems regarding this, try
260 another ALSA compliant mixer (alsamixer works).
265 Module for sound cards based on Aztech System AZT2320 ISA chip (PnP only).
267 port - port # for AZT2320 chip (PnP setup)
268 wss_port - port # for WSS (PnP setup)
269 mpu_port - port # for MPU-401 UART (PnP setup)
270 fm_port - FM port # for AZT2320 chip (PnP setup)
271 irq - IRQ # for AZT2320 (WSS) chip (PnP setup)
272 mpu_irq - IRQ # for MPU-401 UART (PnP setup)
273 dma1 - 1st DMA # for AZT2320 (WSS) chip (PnP setup)
274 dma2 - 2nd DMA # for AZT2320 (WSS) chip (PnP setup)
276 This module supports multiple cards, PnP and autoprobe.
278 The power-management is supported.
283 Module for sound cards based on Aztech AZF3328 PCI chip.
285 joystick - Enable joystick (default off)
287 This module supports multiple cards.
292 Module for video cards based on Bt87x chips.
294 digital_rate - Override the default digital rate (Hz)
295 load_all - Load the driver even if the card model isn't known
297 This module supports multiple cards.
299 Note: The default index value of this module is -2, i.e. the first
305 Module for Creative Audigy LS and SB Live 24bit
307 This module supports multiple cards.
313 Module for sound cards based on C-Media CMI8330 ISA chips.
315 wssport - port # for CMI8330 chip (WSS)
316 wssirq - IRQ # for CMI8330 chip (WSS)
317 wssdma - first DMA # for CMI8330 chip (WSS)
318 sbport - port # for CMI8330 chip (SB16)
319 sbirq - IRQ # for CMI8330 chip (SB16)
320 sbdma8 - 8bit DMA # for CMI8330 chip (SB16)
321 sbdma16 - 16bit DMA # for CMI8330 chip (SB16)
323 This module supports multiple cards and autoprobe.
325 The power-management is supported.
330 Module for C-Media CMI8338 and 8738 PCI sound cards.
332 mpu_port - 0x300,0x310,0x320,0x330, 0 = disable (default)
333 fm_port - 0x388 (default), 0 = disable (default)
334 soft_ac3 - Software-conversion of raw SPDIF packets (model 033 only)
336 joystick_port - Joystick port address (0 = disable, 1 = auto-detect)
338 This module supports autoprobe and multiple cards.
340 The power-management is supported.
345 Module for sound cards based on CS4231 ISA chips.
347 port - port # for CS4231 chip
348 mpu_port - port # for MPU-401 UART (optional), -1 = disable
349 irq - IRQ # for CS4231 chip
350 mpu_irq - IRQ # for MPU-401 UART
351 dma1 - first DMA # for CS4231 chip
352 dma2 - second DMA # for CS4231 chip
354 This module supports multiple cards. This module does not support autoprobe
355 thus main port must be specified!!! Other ports are optional.
357 The power-management is supported.
362 Module for sound cards based on CS4232/CS4232A ISA chips.
364 port - port # for CS4232 chip (PnP setup - 0x534)
365 cport - control port # for CS4232 chip (PnP setup - 0x120,0x210,0xf00)
366 mpu_port - port # for MPU-401 UART (PnP setup - 0x300), -1 = disable
367 fm_port - FM port # for CS4232 chip (PnP setup - 0x388), -1 = disable
368 irq - IRQ # for CS4232 chip (5,7,9,11,12,15)
369 mpu_irq - IRQ # for MPU-401 UART (9,11,12,15)
370 dma1 - first DMA # for CS4232 chip (0,1,3)
371 dma2 - second DMA # for Yamaha CS4232 chip (0,1,3), -1 = disable
372 isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
374 This module supports multiple cards. This module does not support autoprobe
375 thus main port must be specified!!! Other ports are optional.
377 The power-management is supported.
382 Module for sound cards based on CS4235/CS4236/CS4236B/CS4237B/
383 CS4238B/CS4239 ISA chips.
385 port - port # for CS4236 chip (PnP setup - 0x534)
386 cport - control port # for CS4236 chip (PnP setup - 0x120,0x210,0xf00)
387 mpu_port - port # for MPU-401 UART (PnP setup - 0x300), -1 = disable
388 fm_port - FM port # for CS4236 chip (PnP setup - 0x388), -1 = disable
389 irq - IRQ # for CS4236 chip (5,7,9,11,12,15)
390 mpu_irq - IRQ # for MPU-401 UART (9,11,12,15)
391 dma1 - first DMA # for CS4236 chip (0,1,3)
392 dma2 - second DMA # for CS4236 chip (0,1,3), -1 = disable
393 isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
395 This module supports multiple cards. This module does not support autoprobe
396 (if ISA PnP is not used) thus main port and control port must be
397 specified!!! Other ports are optional.
399 The power-management is supported.
404 Module for Cirrus Logic CS4281 soundchip.
406 dual_codec - Secondary codec ID (0 = disable, default)
408 This module supports multiple cards.
410 The power-management is supported.
415 Module for PCI sound cards based on CS4610/CS4612/CS4614/CS4615/CS4622/
416 CS4624/CS4630/CS4280 PCI chips.
418 external_amp - Force to enable external amplifier.
419 thinkpad - Force to enable Thinkpad's CLKRUN control.
420 mmap_valid - Support OSS mmap mode (default = 0).
422 This module supports multiple cards and autoprobe.
423 Usually external amp and CLKRUN controls are detected automatically
424 from PCI sub vendor/device ids. If they don't work, give the options
427 The power-management is supported.
429 Module snd-cs5535audio
430 ----------------------
432 Module for multifunction CS5535 companion PCI device
434 This module supports multiple cards.
439 Module for Diamond Technologies DT-019X / Avance Logic ALS-007 (PnP
442 port - Port # (PnP setup)
443 mpu_port - Port # for MPU-401 (PnP setup)
444 fm_port - Port # for FM OPL-3 (PnP setup)
445 irq - IRQ # (PnP setup)
446 mpu_irq - IRQ # for MPU-401 (PnP setup)
447 dma8 - DMA # (PnP setup)
449 This module supports multiple cards. This module is enabled only with
452 The power-management is supported.
457 Module for the dummy sound card. This "card" doesn't do any output
458 or input, but you may use this module for any application which
459 requires a sound card (like RealPlayer).
461 The power-management is supported.
466 Module for EMU10K1/EMU10k2 based PCI sound cards.
467 * Sound Blaster Live!
468 * Sound Blaster PCI 512
469 * Emu APS (partially supported)
470 * Sound Blaster Audigy
472 extin - bitmap of available external inputs for FX8010 (see bellow)
473 extout - bitmap of available external outputs for FX8010 (see bellow)
474 seq_ports - allocated sequencer ports (4 by default)
475 max_synth_voices - limit of voices used for wavetable (64 by default)
476 max_buffer_size - specifies the maximum size of wavetable/pcm buffers
477 given in MB unit. Default value is 128.
478 enable_ir - enable IR
480 This module supports multiple cards and autoprobe.
482 Input & Output configurations [extin/extout]
483 * Creative Card wo/Digital out [0x0003/0x1f03]
484 * Creative Card w/Digital out [0x0003/0x1f0f]
485 * Creative Card w/Digital CD in [0x000f/0x1f0f]
486 * Creative Card wo/Digital out + LiveDrive [0x3fc3/0x1fc3]
487 * Creative Card w/Digital out + LiveDrive [0x3fc3/0x1fcf]
488 * Creative Card w/Digital CD in + LiveDrive [0x3fcf/0x1fcf]
489 * Creative Card wo/Digital out + Digital I/O 2 [0x0fc3/0x1f0f]
490 * Creative Card w/Digital out + Digital I/O 2 [0x0fc3/0x1f0f]
491 * Creative Card w/Digital CD in + Digital I/O 2 [0x0fcf/0x1f0f]
492 * Creative Card 5.1/w Digital out + LiveDrive [0x3fc3/0x1fff]
493 * Creative Card 5.1 (c) 2003 [0x3fc3/0x7cff]
494 * Creative Card all ins and outs [0x3fff/0x7fff]
496 The power-management is supported.
501 Module for Creative Emu10k1X (SB Live Dell OEM version)
503 This module supports multiple cards.
508 Module for Ensoniq AudioPCI ES1370 PCI sound cards.
509 * SoundBlaster PCI 64
510 * SoundBlaster PCI 128
512 joystick - Enable joystick (default off)
514 This module supports multiple cards and autoprobe.
516 The power-management is supported.
521 Module for Ensoniq AudioPCI ES1371 PCI sound cards.
522 * SoundBlaster PCI 64
523 * SoundBlaster PCI 128
524 * SoundBlaster Vibra PCI
526 joystick_port - port # for joystick (0x200,0x208,0x210,0x218),
527 0 = disable (default), 1 = auto-detect
529 This module supports multiple cards and autoprobe.
531 The power-management is supported.
536 Module for sound cards based on ESS ES968 chip (PnP only).
538 port - port # for ES968 (SB8) chip (PnP setup)
539 irq - IRQ # for ES968 (SB8) chip (PnP setup)
540 dma1 - DMA # for ES968 (SB8) chip (PnP setup)
542 This module supports multiple cards, PnP and autoprobe.
544 The power-management is supported.
549 Module for ESS AudioDrive ES-1688 and ES-688 sound cards.
551 port - port # for ES-1688 chip (0x220,0x240,0x260)
552 mpu_port - port # for MPU-401 port (0x300,0x310,0x320,0x330), -1 = disable (default)
553 irq - IRQ # for ES-1688 chip (5,7,9,10)
554 mpu_irq - IRQ # for MPU-401 port (5,7,9,10)
555 dma8 - DMA # for ES-1688 chip (0,1,3)
557 This module supports multiple cards and autoprobe (without MPU-401 port).
562 Module for ESS AudioDrive ES-18xx sound cards.
564 port - port # for ES-18xx chip (0x220,0x240,0x260)
565 mpu_port - port # for MPU-401 port (0x300,0x310,0x320,0x330), -1 = disable (default)
566 fm_port - port # for FM (optional, not used)
567 irq - IRQ # for ES-18xx chip (5,7,9,10)
568 dma1 - first DMA # for ES-18xx chip (0,1,3)
569 dma2 - first DMA # for ES-18xx chip (0,1,3)
570 isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
572 This module supports multiple cards, ISA PnP and autoprobe (without MPU-401
573 port if native ISA PnP routines are not used).
574 When dma2 is equal with dma1, the driver works as half-duplex.
576 The power-management is supported.
581 Module for sound cards based on ESS Solo-1 (ES1938,ES1946) chips.
583 This module supports multiple cards and autoprobe.
585 The power-management is supported.
590 Module for sound cards based on ESS Maestro-1/2/2E (ES1968/ES1978) chips.
592 total_bufsize - total buffer size in kB (1-4096kB)
593 pcm_substreams_p - playback channels (1-8, default=2)
594 pcm_substreams_c - capture channels (1-8, default=0)
595 clock - clock (0 = auto-detection)
596 use_pm - support the power-management (0 = off, 1 = on,
598 enable_mpu - enable MPU401 (0 = off, 1 = on, 2 = auto (default))
599 joystick - enable joystick (default off)
601 This module supports multiple cards and autoprobe.
603 The power-management is supported.
608 Module for ForteMedia FM801 based PCI sound cards.
610 tea575x_tuner - Enable TEA575x tuner
611 - 1 = MediaForte 256-PCS
612 - 2 = MediaForte 256-PCPR
613 - 3 = MediaForte 64-PCR
614 - High 16-bits are video (radio) device number + 1
615 - example: 0x10002 (MediaForte 256-PCPR, device 1)
617 This module supports multiple cards and autoprobe.
619 The power-management is supported.
621 Module snd-gusclassic
622 ---------------------
624 Module for Gravis UltraSound Classic sound card.
626 port - port # for GF1 chip (0x220,0x230,0x240,0x250,0x260)
627 irq - IRQ # for GF1 chip (3,5,9,11,12,15)
628 dma1 - DMA # for GF1 chip (1,3,5,6,7)
629 dma2 - DMA # for GF1 chip (1,3,5,6,7,-1=disable)
630 joystick_dac - 0 to 31, (0.59V-4.52V or 0.389V-2.98V)
631 voices - GF1 voices limit (14-32)
632 pcm_voices - reserved PCM voices
634 This module supports multiple cards and autoprobe.
636 Module snd-gusextreme
637 ---------------------
639 Module for Gravis UltraSound Extreme (Synergy ViperMax) sound card.
641 port - port # for ES-1688 chip (0x220,0x230,0x240,0x250,0x260)
642 gf1_port - port # for GF1 chip (0x210,0x220,0x230,0x240,0x250,0x260,0x270)
643 mpu_port - port # for MPU-401 port (0x300,0x310,0x320,0x330), -1 = disable
644 irq - IRQ # for ES-1688 chip (5,7,9,10)
645 gf1_irq - IRQ # for GF1 chip (3,5,9,11,12,15)
646 mpu_irq - IRQ # for MPU-401 port (5,7,9,10)
647 dma8 - DMA # for ES-1688 chip (0,1,3)
648 dma1 - DMA # for GF1 chip (1,3,5,6,7)
649 joystick_dac - 0 to 31, (0.59V-4.52V or 0.389V-2.98V)
650 voices - GF1 voices limit (14-32)
651 pcm_voices - reserved PCM voices
653 This module supports multiple cards and autoprobe (without MPU-401 port).
658 Module for Gravis UltraSound MAX sound card.
660 port - port # for GF1 chip (0x220,0x230,0x240,0x250,0x260)
661 irq - IRQ # for GF1 chip (3,5,9,11,12,15)
662 dma1 - DMA # for GF1 chip (1,3,5,6,7)
663 dma2 - DMA # for GF1 chip (1,3,5,6,7,-1=disable)
664 joystick_dac - 0 to 31, (0.59V-4.52V or 0.389V-2.98V)
665 voices - GF1 voices limit (14-32)
666 pcm_voices - reserved PCM voices
668 This module supports multiple cards and autoprobe.
673 Module for Intel HD Audio (ICH6, ICH6M, ICH7), ATI SB450,
676 model - force the model name
677 position_fix - Fix DMA pointer (0 = auto, 1 = none, 2 = POSBUF, 3 = FIFO size)
678 single_cmd - Use single immediate commands to communicate with
679 codecs (for debugging only)
681 This module supports one card and autoprobe.
683 Each codec may have a model table for different configurations.
684 If your machine isn't listed there, the default (usually minimal)
685 configuration is set up. You can pass "model=<name>" option to
686 specify a certain model in such a case. There are different
687 models depending on the codec chip.
689 Model name Description
690 ---------- -----------
692 3stack 3-jack in back and a headphone out
693 3stack-digout 3-jack in back, a HP out and a SPDIF out
694 5stack 5-jack in back, 2-jack in front
695 5stack-digout 5-jack in back, 2-jack in front, a SPDIF out
696 6stack 6-jack in back, 2-jack in front
697 6stack-digout 6-jack with a SPDIF out
699 z71v 3-jack (HP shared SPDIF)
703 lg LG laptop (m1 express dual)
704 test for testing/debugging purpose, almost all controls can be
705 adjusted. Appearing only when compiled with
707 auto auto-config reading BIOS (default)
711 fujitsu Fujitsu S7020
713 basic fixed pin assignment (old default model)
714 auto auto-config reading BIOS (default)
717 fujitsu Fujitsu Laptop
718 basic fixed pin assignment w/o SPDIF
719 auto auto-config reading BIOS (default)
722 3stack-dig 3-jack with SPDIF I/O
723 6stck-dig 6-jack digital with SPDIF I/O
724 auto auto-config reading BIOS (default)
728 3stack-dig 3-jack with SPDIF I/O
729 6stack-dig 6-jack with SPDIF I/O
730 auto auto-config reading BIOS (default)
733 minimal 3-jack in back
734 min_fp 3-jack in back, 2-jack in front
735 full 6-jack in back, 2-jack in front
736 full_dig 6-jack in back, 2-jack in front, SPDIF I/O
737 allout 5-jack in back, 2-jack in front, SPDIF out
738 auto auto-config reading BIOS (default)
741 basic 3-jack (default)
745 6stack 6-jack, separate surrounds (default)
746 3stack 3-stack, shared surrounds
747 laptop 2-channel only (FSC V2060, Samsung M50)
748 laptop-eapd 2-channel with EAPD (Samsung R65, ASUS A6J)
752 6stack-dig ditto with SPDIF
754 3stack-dig ditto with SPDIF
755 laptop 3-jack with hp-jack automute
756 laptop-dig ditto with SPDIF
757 auto auto-confgi reading BIOS (default)
760 vaio Setup for VAIO FE550G/SZ110
762 If the default configuration doesn't work and one of the above
763 matches with your device, report it together with the PCI
764 subsystem ID (output of "lspci -nv") to ALSA BTS or alsa-devel
765 ML (see the section "Links and Addresses").
767 Note 2: If you get click noises on output, try the module option
768 position_fix=1 or 2. position_fix=1 will use the SD_LPIB
769 register value without FIFO size correction as the current
770 DMA pointer. position_fix=2 will make the driver to use
771 the position buffer instead of reading SD_LPIB register.
772 (Usually SD_LPLIB register is more accurate than the
775 NB: If you get many "azx_get_response timeout" messages at
776 loading, it's likely a problem of interrupts (e.g. ACPI irq
777 routing). Try to boot with options like "pci=noacpi". Also, you
778 can try "single_cmd=1" module option. This will switch the
779 communication method between HDA controller and codecs to the
780 single immediate commands instead of CORB/RIRB. Basically, the
781 single command mode is provided only for BIOS, and you won't get
782 unsolicited events, too. But, at least, this works independently
783 from the irq. Remember this is a last resort, and should be
784 avoided as much as possible...
786 The power-management is supported.
791 Module for RME Hammerfall DSP audio interface(s)
793 This module supports multiple cards.
795 Note: The firmware data can be automatically loaded via hotplug
796 when CONFIG_FW_LOADER is set. Otherwise, you need to load
797 the firmware via hdsploader utility included in alsa-tools
799 The firmware data is found in alsa-firmware package.
801 Note: snd-page-alloc module does the job which snd-hammerfall-mem
802 module did formerly. It will allocate the buffers in advance
803 when any HDSP cards are found. To make the buffer
804 allocation sure, load snd-page-alloc module in the early
805 stage of boot sequence. See "Early Buffer Allocation"
811 Module for RME HDSP MADI board.
813 precise_ptr - Enable precise pointer, or disable.
814 line_outs_monitor - Send playback streams to analog outs by default.
815 enable_monitor - Enable Analog Out on Channel 63/64 by default.
817 See hdspm.txt for details.
822 Module for Envy24 (ICE1712) based PCI sound cards.
823 * MidiMan M Audio Delta 1010
824 * MidiMan M Audio Delta 1010LT
825 * MidiMan M Audio Delta DiO 2496
826 * MidiMan M Audio Delta 66
827 * MidiMan M Audio Delta 44
828 * MidiMan M Audio Delta 410
829 * MidiMan M Audio Audiophile 2496
835 * Hoontech SoundTrack DSP 24
836 * Hoontech SoundTrack DSP 24 Value
837 * Hoontech SoundTrack DSP 24 Media 7.1
838 * Event Electronics, EZ8
840 * Lionstracs, Mediastaton
842 model - Use the given board model, one of the following:
843 delta1010, dio2496, delta66, delta44, audiophile, delta410,
844 delta1010lt, vx442, ewx2496, ews88mt, ews88mt_new, ews88d,
845 dmx6fire, dsp24, dsp24_value, dsp24_71, ez8,
846 phase88, mediastation
847 omni - Omni I/O support for MidiMan M-Audio Delta44/66
848 cs8427_timeout - reset timeout for the CS8427 chip (S/PDIF transciever)
849 in msec resolution, default value is 500 (0.5 sec)
851 This module supports multiple cards and autoprobe. Note: The consumer part
852 is not used with all Envy24 based cards (for example in the MidiMan Delta
855 Note: The supported board is detected by reading EEPROM or PCI
856 SSID (if EEPROM isn't available). You can override the
857 model by passing "model" module option in case that the
858 driver isn't configured properly or you want to try another
864 Module for Envy24HT (VT/ICE1724), Envy24PT (VT1720) based PCI sound cards.
865 * MidiMan M Audio Revolution 5.1
866 * MidiMan M Audio Revolution 7.1
868 * TerraTec Aureon 5.1 Sky
869 * TerraTec Aureon 7.1 Space
870 * TerraTec Aureon 7.1 Universe
873 * AudioTrak Prodigy 7.1
874 * AudioTrak Prodigy 7.1LT
875 * AudioTrak Prodigy 192
877 * Albatron K8X800 Pro II
884 model - Use the given board model, one of the following:
885 revo51, revo71, amp2000, prodigy71, prodigy71lt,
886 prodigy192, aureon51, aureon71, universe,
887 k8x800, phase22, phase28, ms300, av710
889 This module supports multiple cards and autoprobe.
891 Note: The supported board is detected by reading EEPROM or PCI
892 SSID (if EEPROM isn't available). You can override the
893 model by passing "model" module option in case that the
894 driver isn't configured properly or you want to try another
900 Module for AC'97 motherboards from Intel and compatibles.
901 * Intel i810/810E, i815, i820, i830, i84x, MX440
902 ICH5, ICH6, ICH7, ESB2
904 * NVidia NForce, NForce2, NForce3, MCP04, CK804
906 * AMD AMD768, AMD8111
909 ac97_clock - AC'97 codec clock base (0 = auto-detect)
910 ac97_quirk - AC'97 workaround for strange hardware
911 See "AC97 Quirk Option" section below.
912 buggy_irq - Enable workaround for buggy interrupts on some
913 motherboards (default yes on nForce chips,
915 buggy_semaphore - Enable workaround for hardwares with buggy
916 semaphores (e.g. on some ASUS laptops)
919 This module supports one chip and autoprobe.
921 Note: the latest driver supports auto-detection of chip clock.
922 if you still encounter too fast playback, specify the clock
923 explicitly via the module option "ac97_clock=41194".
925 Joystick/MIDI ports are not supported by this driver. If your
926 motherboard has these devices, use the ns558 or snd-mpu401
927 modules, respectively.
929 The power-management is supported.
934 Module for Intel ICH (i8x0) chipset MC97 modems.
935 * Intel i810/810E, i815, i820, i830, i84x, MX440
938 * NVidia NForce, NForce2, NForce2s, NForce3
942 ac97_clock - AC'97 codec clock base (0 = auto-detect)
944 This module supports one card and autoprobe.
946 Note: The default index value of this module is -2, i.e. the first
949 The power-management is supported.
954 Module for Gravis UltraSound PnP, Dynasonic 3-D/Pro, STB Sound Rage 32
955 and other sound cards based on AMD InterWave (tm) chip.
957 port - port # for InterWave chip (0x210,0x220,0x230,0x240,0x250,0x260)
958 irq - IRQ # for InterWave chip (3,5,9,11,12,15)
959 dma1 - DMA # for InterWave chip (0,1,3,5,6,7)
960 dma2 - DMA # for InterWave chip (0,1,3,5,6,7,-1=disable)
961 joystick_dac - 0 to 31, (0.59V-4.52V or 0.389V-2.98V)
962 midi - 1 = MIDI UART enable, 0 = MIDI UART disable (default)
963 pcm_voices - reserved PCM voices for the synthesizer (default 2)
964 effect - 1 = InterWave effects enable (default 0);
967 This module supports multiple cards, autoprobe and ISA PnP.
969 Module snd-interwave-stb
970 ------------------------
972 Module for UltraSound 32-Pro (sound card from STB used by Compaq)
973 and other sound cards based on AMD InterWave (tm) chip with TEA6330T
974 circuit for extended control of bass, treble and master volume.
976 port - port # for InterWave chip (0x210,0x220,0x230,0x240,0x250,0x260)
977 port_tc - tone control (i2c bus) port # for TEA6330T chip (0x350,0x360,0x370,0x380)
978 irq - IRQ # for InterWave chip (3,5,9,11,12,15)
979 dma1 - DMA # for InterWave chip (0,1,3,5,6,7)
980 dma2 - DMA # for InterWave chip (0,1,3,5,6,7,-1=disable)
981 joystick_dac - 0 to 31, (0.59V-4.52V or 0.389V-2.98V)
982 midi - 1 = MIDI UART enable, 0 = MIDI UART disable (default)
983 pcm_voices - reserved PCM voices for the synthesizer (default 2)
984 effect - 1 = InterWave effects enable (default 0);
987 This module supports multiple cards, autoprobe and ISA PnP.
992 Module for Korg 1212 IO PCI card
994 This module supports multiple cards.
999 Module for Allegro/Maestro3 chips
1001 external_amp - enable external amp (enabled by default)
1002 amp_gpio - GPIO pin number for external amp (0-15) or
1003 -1 for default pin (8 for allegro, 1 for
1006 This module supports autoprobe and multiple chips.
1008 Note: the binding of amplifier is dependent on hardware.
1009 If there is no sound even though all channels are unmuted, try to
1010 specify other gpio connection via amp_gpio option.
1011 For example, a Panasonic notebook might need "amp_gpio=0x0d"
1014 The power-management is supported.
1019 Module for Digigram miXart8 sound cards.
1021 This module supports multiple cards.
1022 Note: One miXart8 board will be represented as 4 alsa cards.
1023 See MIXART.txt for details.
1025 When the driver is compiled as a module and the hotplug firmware
1026 is supported, the firmware data is loaded via hotplug automatically.
1027 Install the necessary firmware files in alsa-firmware package.
1028 When no hotplug fw loader is available, you need to load the
1029 firmware via mixartloader utility in alsa-tools package.
1034 Module for MPU-401 UART devices.
1036 port - port number or -1 (disable)
1037 irq - IRQ number or -1 (disable)
1038 pnp - PnP detection - 0 = disable, 1 = enable (default)
1040 This module supports multiple devices and PnP.
1045 Module for MOTU MidiTimePiece AV multiport MIDI (on the parallel
1048 port - I/O port # for MTPAV (0x378,0x278, default=0x378)
1049 irq - IRQ # for MTPAV (7,5, default=7)
1050 hwports - number of supported hardware ports, default=8.
1052 Module supports only 1 card. This module has no enable option.
1057 Module for NeoMagic NM256AV/ZX chips
1059 playback_bufsize - max playback frame size in kB (4-128kB)
1060 capture_bufsize - max capture frame size in kB (4-128kB)
1061 force_ac97 - 0 or 1 (disabled by default)
1062 buffer_top - specify buffer top address
1063 use_cache - 0 or 1 (disabled by default)
1064 vaio_hack - alias buffer_top=0x25a800
1065 reset_workaround - enable AC97 RESET workaround for some laptops
1066 reset_workaround2 - enable extended AC97 RESET workaround for some
1069 This module supports one chip and autoprobe.
1071 The power-management is supported.
1073 Note: on some notebooks the buffer address cannot be detected
1074 automatically, or causes hang-up during initialization.
1075 In such a case, specify the buffer top address explicity via
1078 Sony F250: buffer_top=0x25a800
1079 Sony F270: buffer_top=0x272800
1080 The driver supports only ac97 codec. It's possible to force
1081 to initialize/use ac97 although it's not detected. In such a
1082 case, use force_ac97=1 option - but *NO* guarantee whether it
1085 Note: The NM256 chip can be linked internally with non-AC97
1086 codecs. This driver supports only the AC97 codec, and won't work
1087 with machines with other (most likely CS423x or OPL3SAx) chips,
1088 even though the device is detected in lspci. In such a case, try
1089 other drivers, e.g. snd-cs4232 or snd-opl3sa2. Some has ISA-PnP
1090 but some doesn't have ISA PnP. You'll need to specify isapnp=0
1091 and proper hardware parameters in the case without ISA PnP.
1093 Note: some laptops need a workaround for AC97 RESET. For the
1094 known hardware like Dell Latitude LS and Sony PCG-F305, this
1095 workaround is enabled automatically. For other laptops with a
1096 hard freeze, you can try reset_workaround=1 option.
1098 Note: Dell Latitude CSx laptops have another problem regarding
1099 AC97 RESET. On these laptops, reset_workaround2 option is
1100 turned on as default. This option is worth to try if the
1101 previous reset_workaround option doesn't help.
1103 Note: This driver is really crappy. It's a porting from the
1104 OSS driver, which is a result of black-magic reverse engineering.
1105 The detection of codec will fail if the driver is loaded *after*
1106 X-server as described above. You might be able to force to load
1107 the module, but it may result in hang-up. Hence, make sure that
1108 you load this module *before* X if you encounter this kind of
1114 Module for Yamaha OPL3-SA2/SA3 sound cards.
1116 port - control port # for OPL3-SA chip (0x370)
1117 sb_port - SB port # for OPL3-SA chip (0x220,0x240)
1118 wss_port - WSS port # for OPL3-SA chip (0x530,0xe80,0xf40,0x604)
1119 midi_port - port # for MPU-401 UART (0x300,0x330), -1 = disable
1120 fm_port - FM port # for OPL3-SA chip (0x388), -1 = disable
1121 irq - IRQ # for OPL3-SA chip (5,7,9,10)
1122 dma1 - first DMA # for Yamaha OPL3-SA chip (0,1,3)
1123 dma2 - second DMA # for Yamaha OPL3-SA chip (0,1,3), -1 = disable
1124 isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
1126 This module supports multiple cards and ISA PnP. It does not support
1127 autoprobe (if ISA PnP is not used) thus all ports must be specified!!!
1129 The power-management is supported.
1131 Module snd-opti92x-ad1848
1132 -------------------------
1134 Module for sound cards based on OPTi 82c92x and Analog Devices AD1848 chips.
1135 Module works with OAK Mozart cards as well.
1137 port - port # for WSS chip (0x530,0xe80,0xf40,0x604)
1138 mpu_port - port # for MPU-401 UART (0x300,0x310,0x320,0x330)
1139 fm_port - port # for OPL3 device (0x388)
1140 irq - IRQ # for WSS chip (5,7,9,10,11)
1141 mpu_irq - IRQ # for MPU-401 UART (5,7,9,10)
1142 dma1 - first DMA # for WSS chip (0,1,3)
1144 This module supports only one card, autoprobe and PnP.
1146 Module snd-opti92x-cs4231
1147 -------------------------
1149 Module for sound cards based on OPTi 82c92x and Crystal CS4231 chips.
1151 port - port # for WSS chip (0x530,0xe80,0xf40,0x604)
1152 mpu_port - port # for MPU-401 UART (0x300,0x310,0x320,0x330)
1153 fm_port - port # for OPL3 device (0x388)
1154 irq - IRQ # for WSS chip (5,7,9,10,11)
1155 mpu_irq - IRQ # for MPU-401 UART (5,7,9,10)
1156 dma1 - first DMA # for WSS chip (0,1,3)
1157 dma2 - second DMA # for WSS chip (0,1,3)
1159 This module supports only one card, autoprobe and PnP.
1164 Module for sound cards based on OPTi 82c93x chips.
1166 port - port # for WSS chip (0x530,0xe80,0xf40,0x604)
1167 mpu_port - port # for MPU-401 UART (0x300,0x310,0x320,0x330)
1168 fm_port - port # for OPL3 device (0x388)
1169 irq - IRQ # for WSS chip (5,7,9,10,11)
1170 mpu_irq - IRQ # for MPU-401 UART (5,7,9,10)
1171 dma1 - first DMA # for WSS chip (0,1,3)
1172 dma2 - second DMA # for WSS chip (0,1,3)
1174 This module supports only one card, autoprobe and PnP.
1179 Module for Digigram PCXHR boards
1181 This module supports multiple cards.
1183 Module snd-powermac (on ppc only)
1184 ---------------------------------
1186 Module for PowerMac, iMac and iBook on-board soundchips
1188 enable_beep - enable beep using PCM (enabled as default)
1190 Module supports autoprobe a chip.
1192 Note: the driver may have problems regarding endianess.
1194 The power-management is supported.
1196 Module snd-pxa2xx-ac97 (on arm only)
1197 ------------------------------------
1199 Module for AC97 driver for the Intel PXA2xx chip
1201 For ARM architecture only.
1203 The power-management is supported.
1208 Module for RME Digi32, Digi32 Pro and Digi32/8 (Sek'd Prodif32,
1209 Prodif96 and Prodif Gold) sound cards.
1211 This module supports multiple cards.
1216 Module for RME Digi96, Digi96/8 and Digi96/8 PRO/PAD/PST sound cards.
1218 This module supports multiple cards.
1223 Module for RME Digi9652 (Hammerfall, Hammerfall-Light) sound cards.
1225 precise_ptr - Enable precise pointer (doesn't work reliably).
1228 This module supports multiple cards.
1230 Note: snd-page-alloc module does the job which snd-hammerfall-mem
1231 module did formerly. It will allocate the buffers in advance
1232 when any RME9652 cards are found. To make the buffer
1233 allocation sure, load snd-page-alloc module in the early
1234 stage of boot sequence. See "Early Buffer Allocation"
1237 Module snd-sa11xx-uda1341 (on arm only)
1238 ---------------------------------------
1240 Module for Philips UDA1341TS on Compaq iPAQ H3600 sound card.
1242 Module supports only one card.
1243 Module has no enable and index options.
1245 The power-management is supported.
1250 Module for 8-bit SoundBlaster cards: SoundBlaster 1.0,
1254 port - port # for SB DSP chip (0x220,0x240,0x260)
1255 irq - IRQ # for SB DSP chip (5,7,9,10)
1256 dma8 - DMA # for SB DSP chip (1,3)
1258 This module supports multiple cards and autoprobe.
1260 The power-management is supported.
1262 Module snd-sb16 and snd-sbawe
1263 -----------------------------
1265 Module for 16-bit SoundBlaster cards: SoundBlaster 16 (PnP),
1266 SoundBlaster AWE 32 (PnP),
1267 SoundBlaster AWE 64 PnP
1269 port - port # for SB DSP 4.x chip (0x220,0x240,0x260)
1270 mpu_port - port # for MPU-401 UART (0x300,0x330), -1 = disable
1271 awe_port - base port # for EMU8000 synthesizer (0x620,0x640,0x660)
1272 (snd-sbawe module only)
1273 irq - IRQ # for SB DSP 4.x chip (5,7,9,10)
1274 dma8 - 8-bit DMA # for SB DSP 4.x chip (0,1,3)
1275 dma16 - 16-bit DMA # for SB DSP 4.x chip (5,6,7)
1276 mic_agc - Mic Auto-Gain-Control - 0 = disable, 1 = enable (default)
1277 csp - ASP/CSP chip support - 0 = disable (default), 1 = enable
1278 isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
1280 This module supports multiple cards, autoprobe and ISA PnP.
1282 Note: To use Vibra16X cards in 16-bit half duplex mode, you must
1283 disable 16bit DMA with dma16 = -1 module parameter.
1284 Also, all Sound Blaster 16 type cards can operate in 16-bit
1285 half duplex mode through 8-bit DMA channel by disabling their
1288 The power-management is supported.
1293 Module for Aztech Sound Galaxy sound card.
1295 sbport - Port # for SB16 interface (0x220,0x240)
1296 wssport - Port # for WSS interface (0x530,0xe80,0xf40,0x604)
1297 irq - IRQ # (7,9,10,11)
1300 This module supports multiple cards.
1302 The power-management is supported.
1307 Module for ENSONIQ SoundScape PnP cards.
1309 port - Port # (PnP setup)
1310 irq - IRQ # (PnP setup)
1311 mpu_irq - MPU-401 IRQ # (PnP setup)
1312 dma - DMA # (PnP setup)
1314 This module supports multiple cards. ISA PnP must be enabled.
1315 You need sscape_ctl tool in alsa-tools package for loading
1318 Module snd-sun-amd7930 (on sparc only)
1319 --------------------------------------
1321 Module for AMD7930 sound chips found on Sparcs.
1323 This module supports multiple cards.
1325 Module snd-sun-cs4231 (on sparc only)
1326 -------------------------------------
1328 Module for CS4231 sound chips found on Sparcs.
1330 This module supports multiple cards.
1332 Module snd-sun-dbri (on sparc only)
1333 -----------------------------------
1335 Module for DBRI sound chips found on Sparcs.
1337 This module supports multiple cards.
1339 Module snd-wavefront
1340 --------------------
1342 Module for Turtle Beach Maui, Tropez and Tropez+ sound cards.
1344 cs4232_pcm_port - Port # for CS4232 PCM interface.
1345 cs4232_pcm_irq - IRQ # for CS4232 PCM interface (5,7,9,11,12,15).
1346 cs4232_mpu_port - Port # for CS4232 MPU-401 interface.
1347 cs4232_mpu_irq - IRQ # for CS4232 MPU-401 interface (9,11,12,15).
1348 use_cs4232_midi - Use CS4232 MPU-401 interface
1349 (inaccessibly located inside your computer)
1350 ics2115_port - Port # for ICS2115
1351 ics2115_irq - IRQ # for ICS2115
1352 fm_port - FM OPL-3 Port #
1353 dma1 - DMA1 # for CS4232 PCM interface.
1354 dma2 - DMA2 # for CS4232 PCM interface.
1355 isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
1357 This module supports multiple cards and ISA PnP.
1359 Module snd-sonicvibes
1360 ---------------------
1362 Module for S3 SonicVibes PCI sound cards.
1363 * PINE Schubert 32 PCI
1365 reverb - Reverb Enable - 1 = enable, 0 = disable (default)
1366 - SoundCard must have onboard SRAM for this.
1367 mge - Mic Gain Enable - 1 = enable, 0 = disable (default)
1369 This module supports multiple cards and autoprobe.
1371 Module snd-serial-u16550
1372 ------------------------
1374 Module for UART16550A serial MIDI ports.
1376 port - port # for UART16550A chip
1377 irq - IRQ # for UART16550A chip, -1 = poll mode
1378 speed - speed in bauds (9600,19200,38400,57600,115200)
1380 base - base for divisor in bauds (57600,115200,230400,460800)
1382 outs - number of MIDI ports in a serial port (1-4)
1384 adaptor - Type of adaptor.
1385 0 = Soundcanvas, 1 = MS-124T, 2 = MS-124W S/A,
1386 3 = MS-124W M/B, 4 = Generic
1388 This module supports multiple cards. This module does not support autoprobe
1389 thus the main port must be specified!!! Other options are optional.
1394 Module for Trident 4DWave DX/NX sound cards.
1395 * Best Union Miss Melody 4DWave PCI
1397 * Warpspeed ONSpeed 4DWave PCI
1400 * CHIC True Sound 4Dwave
1401 * Shark Predator4D-PCI
1402 * Jaton SonicWave 4D
1404 pcm_channels - max channels (voices) reserved for PCM
1405 wavetable_size - max wavetable size in kB (4-?kb)
1407 This module supports multiple cards and autoprobe.
1409 The power-management is supported.
1411 Module snd-usb-audio
1412 --------------------
1414 Module for USB audio and USB MIDI devices.
1416 vid - Vendor ID for the device (optional)
1417 pid - Product ID for the device (optional)
1418 device_setup - Device specific magic number (optional)
1419 - Influence depends on the device
1422 This module supports multiple devices, autoprobe and hotplugging.
1424 Module snd-usb-usx2y
1425 --------------------
1427 Module for Tascam USB US-122, US-224 and US-428 devices.
1429 This module supports multiple devices, autoprobe and hotplugging.
1431 Note: you need to load the firmware via usx2yloader utility included
1432 in alsa-tools and alsa-firmware packages.
1437 Module for AC'97 motherboards based on VIA 82C686A/686B, 8233,
1438 8233A, 8233C, 8235, 8237 (south) bridge.
1440 mpu_port - 0x300,0x310,0x320,0x330, otherwise obtain BIOS setup
1442 joystick - Enable joystick (default off) [VIA686A/686B only]
1443 ac97_clock - AC'97 codec clock base (default 48000Hz)
1444 dxs_support - support DXS channels,
1445 0 = auto (default), 1 = enable, 2 = disable,
1446 3 = 48k only, 4 = no VRA, 5 = enable any sample
1447 rate and different sample rates on different
1449 [VIA8233/C, 8235, 8237 only]
1450 ac97_quirk - AC'97 workaround for strange hardware
1451 See "AC97 Quirk Option" section below.
1453 This module supports one chip and autoprobe.
1455 Note: on some SMP motherboards like MSI 694D the interrupts might
1456 not be generated properly. In such a case, please try to
1457 set the SMP (or MPS) version on BIOS to 1.1 instead of
1458 default value 1.4. Then the interrupt number will be
1459 assigned under 15. You might also upgrade your BIOS.
1461 Note: VIA8233/5/7 (not VIA8233A) can support DXS (direct sound)
1462 channels as the first PCM. On these channels, up to 4
1463 streams can be played at the same time, and the controller
1464 can perform sample rate conversion with separate rates for
1466 As default (dxs_support = 0), 48k fixed rate is chosen
1467 except for the known devices since the output is often
1468 noisy except for 48k on some mother boards due to the
1470 Please try once dxs_support=5 and if it works on other
1471 sample rates (e.g. 44.1kHz of mp3 playback), please let us
1472 know the PCI subsystem vendor/device id's (output of
1474 If dxs_support=5 does not work, try dxs_support=4; if it
1475 doesn't work too, try dxs_support=1. (dxs_support=1 is
1476 usually for old motherboards. The correct implemented
1477 board should work with 4 or 5.) If it still doesn't
1478 work and the default setting is ok, dxs_support=3 is the
1479 right choice. If the default setting doesn't work at all,
1480 try dxs_support=2 to disable the DXS channels.
1481 In any cases, please let us know the result and the
1482 subsystem vendor/device ids. See "Links and Addresses"
1485 Note: for the MPU401 on VIA823x, use snd-mpu401 driver
1486 additionally. The mpu_port option is for VIA686 chips only.
1488 The power-management is supported.
1490 Module snd-via82xx-modem
1491 ------------------------
1493 Module for VIA82xx AC97 modem
1495 ac97_clock - AC'97 codec clock base (default 48000Hz)
1497 This module supports one card and autoprobe.
1499 Note: The default index value of this module is -2, i.e. the first
1502 The power-management is supported.
1507 Module for virtual rawmidi devices.
1508 This module creates virtual rawmidi devices which communicate
1509 to the corresponding ALSA sequencer ports.
1511 midi_devs - MIDI devices # (1-4, default=4)
1513 This module supports multiple cards.
1518 Module for Digigram VX-Pocket VX222, V222 v2 and Mic cards.
1520 mic - Enable Microphone on V222 Mic (NYI)
1521 ibl - Capture IBL size. (default = 0, minimum size)
1523 This module supports multiple cards.
1525 When the driver is compiled as a module and the hotplug firmware
1526 is supported, the firmware data is loaded via hotplug automatically.
1527 Install the necessary firmware files in alsa-firmware package.
1528 When no hotplug fw loader is available, you need to load the
1529 firmware via vxloader utility in alsa-tools package. To invoke
1530 vxloader automatically, add the following to /etc/modprobe.conf
1532 install snd-vx222 /sbin/modprobe --first-time -i snd-vx222 && /usr/bin/vxloader
1534 (for 2.2/2.4 kernels, add "post-install /usr/bin/vxloader" to
1535 /etc/modules.conf, instead.)
1536 IBL size defines the interrupts period for PCM. The smaller size
1537 gives smaller latency but leads to more CPU consumption, too.
1538 The size is usually aligned to 126. As default (=0), the smallest
1539 size is chosen. The possible IBL values can be found in
1540 /proc/asound/cardX/vx-status proc file.
1542 The power-management is supported.
1547 Module for Digigram VX-Pocket VX2 and 440 PCMCIA cards.
1549 ibl - Capture IBL size. (default = 0, minimum size)
1551 This module supports multiple cards. The module is compiled only when
1552 PCMCIA is supported on kernel.
1554 With the older 2.6.x kernel, to activate the driver via the card
1555 manager, you'll need to set up /etc/pcmcia/vxpocket.conf. See the
1556 sound/pcmcia/vx/vxpocket.c. 2.6.13 or later kernel requires no
1557 longer require a config file.
1559 When the driver is compiled as a module and the hotplug firmware
1560 is supported, the firmware data is loaded via hotplug automatically.
1561 Install the necessary firmware files in alsa-firmware package.
1562 When no hotplug fw loader is available, you need to load the
1563 firmware via vxloader utility in alsa-tools package.
1565 About capture IBL, see the description of snd-vx222 module.
1567 Note: the driver is build only when CONFIG_ISA is set.
1569 Note2: snd-vxp440 driver is merged to snd-vxpocket driver since
1572 The power-management is supported.
1577 Module for Yamaha PCI chips (YMF72x, YMF74x & YMF75x).
1579 mpu_port - 0x300,0x330,0x332,0x334, 0 (disable) by default,
1580 1 (auto-detect for YMF744/754 only)
1581 fm_port - 0x388,0x398,0x3a0,0x3a8, 0 (disable) by default
1582 1 (auto-detect for YMF744/754 only)
1583 joystick_port - 0x201,0x202,0x204,0x205, 0 (disable) by default,
1585 rear_switch - enable shared rear/line-in switch (bool)
1587 This module supports autoprobe and multiple chips.
1589 The power-management is supported.
1591 Module snd-pdaudiocf
1592 --------------------
1594 Module for Sound Core PDAudioCF sound card.
1596 Note: the driver is build only when CONFIG_ISA is set.
1598 The power-management is supported.
1604 The ac97_quirk option is used to enable/override the workaround for
1605 specific devices on drivers for on-board AC'97 controllers like
1606 snd-intel8x0. Some hardware have swapped output pins between Master
1607 and Headphone, or Surround (thanks to confusion of AC'97
1608 specifications from version to version :-)
1610 The driver provides the auto-detection of known problematic devices,
1611 but some might be unknown or wrongly detected. In such a case, pass
1612 the proper value with this option.
1614 The following strings are accepted:
1615 - default Don't override the default setting
1616 - none Disable the quirk
1617 - hp_only Bind Master and Headphone controls as a single control
1618 - swap_hp Swap headphone and master controls
1619 - swap_surround Swap master and surround controls
1620 - ad_sharing For AD1985, turn on OMS bit and use headphone
1621 - alc_jack For ALC65x, turn on the jack sense mode
1622 - inv_eapd Inverted EAPD implementation
1623 - mute_led Bind EAPD bit for turning on/off mute LED
1625 For backward compatibility, the corresponding integer value -1, 0,
1626 ... are accepted, too.
1628 For example, if "Master" volume control has no effect on your device
1629 but only "Headphone" does, pass ac97_quirk=hp_only module option.
1632 Configuring Non-ISAPNP Cards
1633 ============================
1635 When the kernel is configured with ISA-PnP support, the modules
1636 supporting the isapnp cards will have module options "isapnp".
1637 If this option is set, *only* the ISA-PnP devices will be probed.
1638 For probing the non ISA-PnP cards, you have to pass "isapnp=0" option
1639 together with the proper i/o and irq configuration.
1641 When the kernel is configured without ISA-PnP support, isapnp option
1642 will be not built in.
1645 Module Autoloading Support
1646 ==========================
1648 The ALSA drivers can be loaded automatically on demand by defining
1649 module aliases. The string 'snd-card-%1' is requested for ALSA native
1650 devices where %i is sound card number from zero to seven.
1652 To auto-load an ALSA driver for OSS services, define the string
1653 'sound-slot-%i' where %i means the slot number for OSS, which
1654 corresponds to the card index of ALSA. Usually, define this
1655 as the same card module.
1657 An example configuration for a single emu10k1 card is like below:
1658 ----- /etc/modprobe.conf
1659 alias snd-card-0 snd-emu10k1
1660 alias sound-slot-0 snd-emu10k1
1661 ----- /etc/modprobe.conf
1663 The available number of auto-loaded sound cards depends on the module
1664 option "cards_limit" of snd module. As default it's set to 1.
1665 To enable the auto-loading of multiple cards, specify the number of
1666 sound cards in that option.
1668 When multiple cards are available, it'd better to specify the index
1669 number for each card via module option, too, so that the order of
1670 cards is kept consistent.
1672 An example configuration for two sound cards is like below:
1674 ----- /etc/modprobe.conf
1676 options snd cards_limit=2
1677 alias snd-card-0 snd-interwave
1678 alias snd-card-1 snd-ens1371
1679 options snd-interwave index=0
1680 options snd-ens1371 index=1
1682 alias sound-slot-0 snd-interwave
1683 alias sound-slot-1 snd-ens1371
1684 ----- /etc/moprobe.conf
1686 In this example, the interwave card is always loaded as the first card
1687 (index 0) and ens1371 as the second (index 1).
1690 ALSA PCM devices to OSS devices mapping
1691 =======================================
1693 /dev/snd/pcmC0D0[c|p] -> /dev/audio0 (/dev/audio) -> minor 4
1694 /dev/snd/pcmC0D0[c|p] -> /dev/dsp0 (/dev/dsp) -> minor 3
1695 /dev/snd/pcmC0D1[c|p] -> /dev/adsp0 (/dev/adsp) -> minor 12
1696 /dev/snd/pcmC1D0[c|p] -> /dev/audio1 -> minor 4+16 = 20
1697 /dev/snd/pcmC1D0[c|p] -> /dev/dsp1 -> minor 3+16 = 19
1698 /dev/snd/pcmC1D1[c|p] -> /dev/adsp1 -> minor 12+16 = 28
1699 /dev/snd/pcmC2D0[c|p] -> /dev/audio2 -> minor 4+32 = 36
1700 /dev/snd/pcmC2D0[c|p] -> /dev/dsp2 -> minor 3+32 = 39
1701 /dev/snd/pcmC2D1[c|p] -> /dev/adsp2 -> minor 12+32 = 44
1703 The first number from /dev/snd/pcmC{X}D{Y}[c|p] expression means
1704 sound card number and second means device number. The ALSA devices
1705 have either 'c' or 'p' suffix indicating the direction, capture and
1706 playback, respectively.
1708 Please note that the device mapping above may be varied via the module
1709 options of snd-pcm-oss module.
1715 The ALSA driver fully supports the devfs extension.
1716 You should add lines below to your devfsd.conf file:
1718 LOOKUP snd MODLOAD ACTION snd
1719 REGISTER ^sound/.* PERMISSIONS root.audio 660
1720 REGISTER ^snd/.* PERMISSIONS root.audio 660
1722 Warning: These lines assume that you have the audio group in your system.
1723 Otherwise replace audio word with another group name (root for
1727 Proc interfaces (/proc/asound)
1728 ==============================
1730 /proc/asound/card#/pcm#[cp]/oss
1731 -------------------------------
1732 String "erase" - erase all additional informations about OSS applications
1733 String "<app_name> <fragments> <fragment_size> [<options>]"
1735 <app_name> - name of application with (higher priority) or without path
1736 <fragments> - number of fragments or zero if auto
1737 <fragment_size> - size of fragment in bytes or zero if auto
1738 <options> - optional parameters
1739 - disable the application tries to open a pcm device for
1740 this channel but does not want to use it.
1741 (Cause a bug or mmap needs)
1742 It's good for Quake etc...
1743 - direct don't use plugins
1744 - block force block mode (rvplayer)
1745 - non-block force non-block mode
1746 - whole-frag write only whole fragments (optimization affecting
1748 - no-silence do not fill silence ahead to avoid clicks
1749 - buggy-ptr Returns the whitespace blocks in GETOPTR ioctl
1750 instead of filled blocks
1752 Example: echo "x11amp 128 16384" > /proc/asound/card0/pcm0p/oss
1753 echo "squake 0 0 disable" > /proc/asound/card0/pcm0c/oss
1754 echo "rvplayer 0 0 block" > /proc/asound/card0/pcm0p/oss
1757 Early Buffer Allocation
1758 =======================
1760 Some drivers (e.g. hdsp) require the large contiguous buffers, and
1761 sometimes it's too late to find such spaces when the driver module is
1762 actually loaded due to memory fragmentation. You can pre-allocate the
1763 PCM buffers by loading snd-page-alloc module and write commands to its
1764 proc file in prior, for example, in the early boot stage like
1765 /etc/init.d/*.local scripts.
1767 Reading the proc file /proc/drivers/snd-page-alloc shows the current
1768 usage of page allocation. In writing, you can send the following
1769 commands to the snd-page-alloc driver:
1771 - add VENDOR DEVICE MASK SIZE BUFFERS
1773 VENDOR and DEVICE are PCI vendor and device IDs. They take
1774 integer numbers (0x prefix is needed for the hex).
1775 MASK is the PCI DMA mask. Pass 0 if not restricted.
1776 SIZE is the size of each buffer to allocate. You can pass
1777 k and m suffix for KB and MB. The max number is 16MB.
1778 BUFFERS is the number of buffers to allocate. It must be greater
1779 than 0. The max number is 4.
1783 This will erase the all pre-allocated buffers which are not in
1790 ALSA project homepage
1791 http://www.alsa-project.org
1793 ALSA Bug Tracking System
1794 https://bugtrack.alsa-project.org/bugs/
1797 mailto:alsa-devel@lists.sourceforge.net