2 * Copyright (C) 2011-2013 Texas Instruments Incorporated - http://www.ti.com/
4 * This program is free software; you can redistribute it and/or modify
5 * it under the terms of the GNU General Public License version 2 as
6 * published by the Free Software Foundation.
8 #include "elpida_ecb240abacn.dtsi"
12 device_type = "memory";
13 reg = <0x80000000 0x40000000>; /* 1 GB */
22 compatible = "gpio-leds";
23 pinctrl-names = "default";
29 label = "pandaboard::status1";
30 gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
31 linux,default-trigger = "heartbeat";
35 label = "pandaboard::status2";
36 gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
37 linux,default-trigger = "mmc0";
42 compatible = "ti,abe-twl6040";
43 ti,model = "PandaBoard";
45 ti,mclk-freq = <38400000>;
49 ti,twl6040 = <&twl6040>;
53 "Headset Stereophone", "HSOL",
54 "Headset Stereophone", "HSOR",
59 "HSMIC", "Headset Mic",
60 "Headset Mic", "Headset Mic Bias",
65 /* HS USB Port 1 Power */
66 hsusb1_power: hsusb1_power_reg {
67 compatible = "regulator-fixed";
68 regulator-name = "hsusb1_vbus";
69 regulator-min-microvolt = <3300000>;
70 regulator-max-microvolt = <3300000>;
71 gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>; /* gpio_1 */
72 startup-delay-us = <70000>;
75 * boot-on is required along with always-on as the
76 * regulator framework doesn't enable the regulator
77 * if boot-on is not there.
83 /* HS USB Host PHY on PORT 1 */
84 hsusb1_phy: hsusb1_phy {
85 compatible = "usb-nop-xceiv";
86 reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>; /* gpio_62 */
87 vcc-supply = <&hsusb1_power>;
88 clocks = <&auxclk3_ck>;
89 clock-names = "main_clk";
90 clock-frequency = <19200000>;
93 /* regulator for wl12xx on sdio5 */
94 wl12xx_vmmc: wl12xx_vmmc {
95 pinctrl-names = "default";
96 pinctrl-0 = <&wl12xx_gpio>;
97 compatible = "regulator-fixed";
98 regulator-name = "vwl1271";
99 regulator-min-microvolt = <1800000>;
100 regulator-max-microvolt = <1800000>;
101 gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>;
102 startup-delay-us = <70000>;
107 compatible = "ti,tfp410";
108 powerdown-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; /* gpio_0 */
111 #address-cells = <1>;
117 tfp410_in: endpoint@0 {
118 remote-endpoint = <&dpi_out>;
125 tfp410_out: endpoint@0 {
126 remote-endpoint = <&dvi_connector_in>;
133 compatible = "dvi-connector";
138 ddc-i2c-bus = <&i2c3>;
141 dvi_connector_in: endpoint {
142 remote-endpoint = <&tfp410_out>;
147 tpd12s015: encoder@1 {
148 compatible = "ti,tpd12s015";
150 gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */
151 <&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */
152 <&gpio2 31 GPIO_ACTIVE_HIGH>; /* 63, HPD */
155 #address-cells = <1>;
161 tpd12s015_in: endpoint@0 {
162 remote-endpoint = <&hdmi_out>;
169 tpd12s015_out: endpoint@0 {
170 remote-endpoint = <&hdmi_connector_in>;
177 compatible = "hdmi-connector";
183 hdmi_connector_in: endpoint {
184 remote-endpoint = <&tpd12s015_out>;
191 pinctrl-names = "default";
200 twl6040_pins: pinmux_twl6040_pins {
201 pinctrl-single,pins = <
202 OMAP4_IOPAD(0x120, PIN_OUTPUT | MUX_MODE3) /* hdq_sio.gpio_127 */
203 OMAP4_IOPAD(0x1a0, PIN_INPUT | MUX_MODE0) /* sys_nirq2.sys_nirq2 */
207 mcpdm_pins: pinmux_mcpdm_pins {
208 pinctrl-single,pins = <
209 OMAP4_IOPAD(0x106, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_ul_data.abe_pdm_ul_data */
210 OMAP4_IOPAD(0x108, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_dl_data.abe_pdm_dl_data */
211 OMAP4_IOPAD(0x10a, PIN_INPUT_PULLUP | MUX_MODE0) /* abe_pdm_frame.abe_pdm_frame */
212 OMAP4_IOPAD(0x10c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_lb_clk.abe_pdm_lb_clk */
213 OMAP4_IOPAD(0x10e, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */
217 mcbsp1_pins: pinmux_mcbsp1_pins {
218 pinctrl-single,pins = <
219 OMAP4_IOPAD(0x0fe, PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_clkx.abe_mcbsp1_clkx */
220 OMAP4_IOPAD(0x100, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dr.abe_mcbsp1_dr */
221 OMAP4_IOPAD(0x102, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dx.abe_mcbsp1_dx */
222 OMAP4_IOPAD(0x104, PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_fsx.abe_mcbsp1_fsx */
226 dss_dpi_pins: pinmux_dss_dpi_pins {
227 pinctrl-single,pins = <
228 OMAP4_IOPAD(0x162, PIN_OUTPUT | MUX_MODE5) /* dispc2_data23 */
229 OMAP4_IOPAD(0x164, PIN_OUTPUT | MUX_MODE5) /* dispc2_data22 */
230 OMAP4_IOPAD(0x166, PIN_OUTPUT | MUX_MODE5) /* dispc2_data21 */
231 OMAP4_IOPAD(0x168, PIN_OUTPUT | MUX_MODE5) /* dispc2_data20 */
232 OMAP4_IOPAD(0x16a, PIN_OUTPUT | MUX_MODE5) /* dispc2_data19 */
233 OMAP4_IOPAD(0x16c, PIN_OUTPUT | MUX_MODE5) /* dispc2_data18 */
234 OMAP4_IOPAD(0x16e, PIN_OUTPUT | MUX_MODE5) /* dispc2_data15 */
235 OMAP4_IOPAD(0x170, PIN_OUTPUT | MUX_MODE5) /* dispc2_data14 */
236 OMAP4_IOPAD(0x172, PIN_OUTPUT | MUX_MODE5) /* dispc2_data13 */
237 OMAP4_IOPAD(0x174, PIN_OUTPUT | MUX_MODE5) /* dispc2_data12 */
238 OMAP4_IOPAD(0x176, PIN_OUTPUT | MUX_MODE5) /* dispc2_data11 */
240 OMAP4_IOPAD(0x1b4, PIN_OUTPUT | MUX_MODE5) /* dispc2_data10 */
241 OMAP4_IOPAD(0x1b6, PIN_OUTPUT | MUX_MODE5) /* dispc2_data9 */
242 OMAP4_IOPAD(0x1b8, PIN_OUTPUT | MUX_MODE5) /* dispc2_data16 */
243 OMAP4_IOPAD(0x1ba, PIN_OUTPUT | MUX_MODE5) /* dispc2_data17 */
244 OMAP4_IOPAD(0x1bc, PIN_OUTPUT | MUX_MODE5) /* dispc2_hsync */
245 OMAP4_IOPAD(0x1be, PIN_OUTPUT | MUX_MODE5) /* dispc2_pclk */
246 OMAP4_IOPAD(0x1c0, PIN_OUTPUT | MUX_MODE5) /* dispc2_vsync */
247 OMAP4_IOPAD(0x1c2, PIN_OUTPUT | MUX_MODE5) /* dispc2_de */
248 OMAP4_IOPAD(0x1c4, PIN_OUTPUT | MUX_MODE5) /* dispc2_data8 */
249 OMAP4_IOPAD(0x1c6, PIN_OUTPUT | MUX_MODE5) /* dispc2_data7 */
250 OMAP4_IOPAD(0x1c8, PIN_OUTPUT | MUX_MODE5) /* dispc2_data6 */
251 OMAP4_IOPAD(0x1ca, PIN_OUTPUT | MUX_MODE5) /* dispc2_data5 */
252 OMAP4_IOPAD(0x1cc, PIN_OUTPUT | MUX_MODE5) /* dispc2_data4 */
253 OMAP4_IOPAD(0x1ce, PIN_OUTPUT | MUX_MODE5) /* dispc2_data3 */
255 OMAP4_IOPAD(0x1d0, PIN_OUTPUT | MUX_MODE5) /* dispc2_data2 */
256 OMAP4_IOPAD(0x1d2, PIN_OUTPUT | MUX_MODE5) /* dispc2_data1 */
257 OMAP4_IOPAD(0x1d4, PIN_OUTPUT | MUX_MODE5) /* dispc2_data0 */
261 tfp410_pins: pinmux_tfp410_pins {
262 pinctrl-single,pins = <
263 OMAP4_IOPAD(0x184, PIN_OUTPUT | MUX_MODE3) /* gpio_0 */
267 dss_hdmi_pins: pinmux_dss_hdmi_pins {
268 pinctrl-single,pins = <
269 OMAP4_IOPAD(0x09a, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */
270 OMAP4_IOPAD(0x09c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */
271 OMAP4_IOPAD(0x09e, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */
275 tpd12s015_pins: pinmux_tpd12s015_pins {
276 pinctrl-single,pins = <
277 OMAP4_IOPAD(0x062, PIN_OUTPUT | MUX_MODE3) /* gpmc_a17.gpio_41 */
278 OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3) /* gpmc_nbe1.gpio_60 */
279 OMAP4_IOPAD(0x098, PIN_INPUT_PULLDOWN | MUX_MODE3) /* hdmi_hpd.gpio_63 */
283 hsusbb1_pins: pinmux_hsusbb1_pins {
284 pinctrl-single,pins = <
285 OMAP4_IOPAD(0x0c2, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_clk.usbb1_ulpiphy_clk */
286 OMAP4_IOPAD(0x0c4, PIN_OUTPUT | MUX_MODE4) /* usbb1_ulpitll_stp.usbb1_ulpiphy_stp */
287 OMAP4_IOPAD(0x0c6, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dir.usbb1_ulpiphy_dir */
288 OMAP4_IOPAD(0x0c8, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_nxt.usbb1_ulpiphy_nxt */
289 OMAP4_IOPAD(0x0ca, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat0.usbb1_ulpiphy_dat0 */
290 OMAP4_IOPAD(0x0cc, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat1.usbb1_ulpiphy_dat1 */
291 OMAP4_IOPAD(0x0ce, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat2.usbb1_ulpiphy_dat2 */
292 OMAP4_IOPAD(0x0d0, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat3.usbb1_ulpiphy_dat3 */
293 OMAP4_IOPAD(0x0d2, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat4.usbb1_ulpiphy_dat4 */
294 OMAP4_IOPAD(0x0d4, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat5.usbb1_ulpiphy_dat5 */
295 OMAP4_IOPAD(0x0d6, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat6.usbb1_ulpiphy_dat6 */
296 OMAP4_IOPAD(0x0d8, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat7.usbb1_ulpiphy_dat7 */
300 i2c1_pins: pinmux_i2c1_pins {
301 pinctrl-single,pins = <
302 OMAP4_IOPAD(0x122, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
303 OMAP4_IOPAD(0x124, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
307 i2c2_pins: pinmux_i2c2_pins {
308 pinctrl-single,pins = <
309 OMAP4_IOPAD(0x126, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */
310 OMAP4_IOPAD(0x128, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */
314 i2c3_pins: pinmux_i2c3_pins {
315 pinctrl-single,pins = <
316 OMAP4_IOPAD(0x12a, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */
317 OMAP4_IOPAD(0x12c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */
321 i2c4_pins: pinmux_i2c4_pins {
322 pinctrl-single,pins = <
323 OMAP4_IOPAD(0x12e, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */
324 OMAP4_IOPAD(0x130, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */
329 * wl12xx GPIO outputs for WLAN_EN, BT_EN, FM_EN, BT_WAKEUP
330 * REVISIT: Are the pull-ups needed for GPIO 48 and 49?
332 wl12xx_gpio: pinmux_wl12xx_gpio {
333 pinctrl-single,pins = <
334 OMAP4_IOPAD(0x066, PIN_OUTPUT | MUX_MODE3) /* gpmc_a19.gpio_43 */
335 OMAP4_IOPAD(0x06c, PIN_OUTPUT | MUX_MODE3) /* gpmc_a22.gpio_46 */
336 OMAP4_IOPAD(0x070, PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a24.gpio_48 */
337 OMAP4_IOPAD(0x072, PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a25.gpio_49 */
341 /* wl12xx GPIO inputs and SDIO pins */
342 wl12xx_pins: pinmux_wl12xx_pins {
343 pinctrl-single,pins = <
344 OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3) /* gpmc_ncs2.gpio_52 */
345 OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3) /* gpmc_ncs3.gpio_53 */
346 OMAP4_IOPAD(0x148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_clk.sdmmc5_clk */
347 OMAP4_IOPAD(0x14a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_cmd.sdmmc5_cmd */
348 OMAP4_IOPAD(0x14c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat0.sdmmc5_dat0 */
349 OMAP4_IOPAD(0x14e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat1.sdmmc5_dat1 */
350 OMAP4_IOPAD(0x150, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat2.sdmmc5_dat2 */
351 OMAP4_IOPAD(0x152, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat3.sdmmc5_dat3 */
357 led_wkgpio_pins: pinmux_leds_wkpins {
358 pinctrl-single,pins = <
359 OMAP4_IOPAD(0x05a, PIN_OUTPUT | MUX_MODE3) /* gpio_wk7 */
360 OMAP4_IOPAD(0x05c, PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */
366 pinctrl-names = "default";
367 pinctrl-0 = <&i2c1_pins>;
369 clock-frequency = <400000>;
374 interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */
378 compatible = "ti,twl6040";
381 pinctrl-names = "default";
382 pinctrl-0 = <&twl6040_pins>;
385 interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */
386 ti,audpwron-gpio = <&gpio4 31 GPIO_ACTIVE_HIGH>; /* gpio line 127 */
388 vio-supply = <&v1v8>;
389 v2v1-supply = <&v2v1>;
394 #include "twl6030.dtsi"
395 #include "twl6030_omap4.dtsi"
398 pinctrl-names = "default";
399 pinctrl-0 = <&i2c2_pins>;
401 clock-frequency = <400000>;
405 pinctrl-names = "default";
406 pinctrl-0 = <&i2c3_pins>;
408 clock-frequency = <100000>;
411 * Display monitor features are burnt in their EEPROM as EDID data.
412 * The EEPROM is connected as I2C slave device.
415 compatible = "ti,eeprom";
421 pinctrl-names = "default";
422 pinctrl-0 = <&i2c4_pins>;
424 clock-frequency = <400000>;
428 vmmc-supply = <&vmmc>;
445 pinctrl-names = "default";
446 pinctrl-0 = <&wl12xx_pins>;
447 vmmc-supply = <&wl12xx_vmmc>;
452 #address-cells = <1>;
455 compatible = "ti,wl1271";
457 interrupt-parent = <&gpio2>;
458 interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; /* gpio 53 */
459 ref-clock-frequency = <38400000>;
465 device-handle = <&elpida_ECB240ABACN>;
470 device-handle = <&elpida_ECB240ABACN>;
474 pinctrl-names = "default";
475 pinctrl-0 = <&mcbsp1_pins>;
480 pinctrl-names = "default";
481 pinctrl-0 = <&mcpdm_pins>;
485 &twl_usb_comparator {
486 usb-supply = <&vusb>;
490 interrupts-extended = <&wakeupgen GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH
491 &omap4_pmx_core OMAP4_UART2_RX>;
495 interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH
496 &omap4_pmx_core OMAP4_UART3_RX>;
500 interrupts-extended = <&wakeupgen GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH
501 &omap4_pmx_core OMAP4_UART4_RX>;
505 interface-type = <1>;
511 port1-mode = "ehci-phy";
515 phys = <&hsusb1_phy>;
523 remote-endpoint = <&tfp410_in>;
531 vdd-supply = <&vcxio>;
536 vdda-supply = <&vdac>;
540 remote-endpoint = <&tpd12s015_in>;