Merge remote-tracking branch 'workqueues/for-next'
[deliverable/linux.git] / arch / arm / mach-ixp4xx / ixdp425-setup.c
1 /*
2 * arch/arm/mach-ixp4xx/ixdp425-setup.c
3 *
4 * IXDP425/IXCDP1100 board-setup
5 *
6 * Copyright (C) 2003-2005 MontaVista Software, Inc.
7 *
8 * Author: Deepak Saxena <dsaxena@plexity.net>
9 */
10
11 #include <linux/kernel.h>
12 #include <linux/init.h>
13 #include <linux/device.h>
14 #include <linux/serial.h>
15 #include <linux/tty.h>
16 #include <linux/serial_8250.h>
17 #include <linux/i2c-gpio.h>
18 #include <linux/io.h>
19 #include <linux/mtd/mtd.h>
20 #include <linux/mtd/nand.h>
21 #include <linux/mtd/partitions.h>
22 #include <linux/delay.h>
23 #include <linux/gpio.h>
24 #include <asm/types.h>
25 #include <asm/setup.h>
26 #include <asm/memory.h>
27 #include <mach/hardware.h>
28 #include <asm/mach-types.h>
29 #include <asm/irq.h>
30 #include <asm/mach/arch.h>
31 #include <asm/mach/flash.h>
32
33 #define IXDP425_SDA_PIN 7
34 #define IXDP425_SCL_PIN 6
35
36 /* NAND Flash pins */
37 #define IXDP425_NAND_NCE_PIN 12
38
39 #define IXDP425_NAND_CMD_BYTE 0x01
40 #define IXDP425_NAND_ADDR_BYTE 0x02
41
42 static struct flash_platform_data ixdp425_flash_data = {
43 .map_name = "cfi_probe",
44 .width = 2,
45 };
46
47 static struct resource ixdp425_flash_resource = {
48 .flags = IORESOURCE_MEM,
49 };
50
51 static struct platform_device ixdp425_flash = {
52 .name = "IXP4XX-Flash",
53 .id = 0,
54 .dev = {
55 .platform_data = &ixdp425_flash_data,
56 },
57 .num_resources = 1,
58 .resource = &ixdp425_flash_resource,
59 };
60
61 #if defined(CONFIG_MTD_NAND_PLATFORM) || \
62 defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
63
64 static struct mtd_partition ixdp425_partitions[] = {
65 {
66 .name = "ixp400 NAND FS 0",
67 .offset = 0,
68 .size = SZ_8M
69 }, {
70 .name = "ixp400 NAND FS 1",
71 .offset = MTDPART_OFS_APPEND,
72 .size = MTDPART_SIZ_FULL
73 },
74 };
75
76 static void
77 ixdp425_flash_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
78 {
79 struct nand_chip *this = mtd_to_nand(mtd);
80 int offset = (int)nand_get_controller_data(this);
81
82 if (ctrl & NAND_CTRL_CHANGE) {
83 if (ctrl & NAND_NCE) {
84 gpio_set_value(IXDP425_NAND_NCE_PIN, 0);
85 udelay(5);
86 } else
87 gpio_set_value(IXDP425_NAND_NCE_PIN, 1);
88
89 offset = (ctrl & NAND_CLE) ? IXDP425_NAND_CMD_BYTE : 0;
90 offset |= (ctrl & NAND_ALE) ? IXDP425_NAND_ADDR_BYTE : 0;
91 nand_set_controller_data(this, (void *)offset);
92 }
93
94 if (cmd != NAND_CMD_NONE)
95 writeb(cmd, this->IO_ADDR_W + offset);
96 }
97
98 static struct platform_nand_data ixdp425_flash_nand_data = {
99 .chip = {
100 .nr_chips = 1,
101 .chip_delay = 30,
102 .partitions = ixdp425_partitions,
103 .nr_partitions = ARRAY_SIZE(ixdp425_partitions),
104 },
105 .ctrl = {
106 .cmd_ctrl = ixdp425_flash_nand_cmd_ctrl
107 }
108 };
109
110 static struct resource ixdp425_flash_nand_resource = {
111 .flags = IORESOURCE_MEM,
112 };
113
114 static struct platform_device ixdp425_flash_nand = {
115 .name = "gen_nand",
116 .id = -1,
117 .dev = {
118 .platform_data = &ixdp425_flash_nand_data,
119 },
120 .num_resources = 1,
121 .resource = &ixdp425_flash_nand_resource,
122 };
123 #endif /* CONFIG_MTD_NAND_PLATFORM */
124
125 static struct i2c_gpio_platform_data ixdp425_i2c_gpio_data = {
126 .sda_pin = IXDP425_SDA_PIN,
127 .scl_pin = IXDP425_SCL_PIN,
128 };
129
130 static struct platform_device ixdp425_i2c_gpio = {
131 .name = "i2c-gpio",
132 .id = 0,
133 .dev = {
134 .platform_data = &ixdp425_i2c_gpio_data,
135 },
136 };
137
138 static struct resource ixdp425_uart_resources[] = {
139 {
140 .start = IXP4XX_UART1_BASE_PHYS,
141 .end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
142 .flags = IORESOURCE_MEM
143 },
144 {
145 .start = IXP4XX_UART2_BASE_PHYS,
146 .end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
147 .flags = IORESOURCE_MEM
148 }
149 };
150
151 static struct plat_serial8250_port ixdp425_uart_data[] = {
152 {
153 .mapbase = IXP4XX_UART1_BASE_PHYS,
154 .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
155 .irq = IRQ_IXP4XX_UART1,
156 .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
157 .iotype = UPIO_MEM,
158 .regshift = 2,
159 .uartclk = IXP4XX_UART_XTAL,
160 },
161 {
162 .mapbase = IXP4XX_UART2_BASE_PHYS,
163 .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
164 .irq = IRQ_IXP4XX_UART2,
165 .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
166 .iotype = UPIO_MEM,
167 .regshift = 2,
168 .uartclk = IXP4XX_UART_XTAL,
169 },
170 { },
171 };
172
173 static struct platform_device ixdp425_uart = {
174 .name = "serial8250",
175 .id = PLAT8250_DEV_PLATFORM,
176 .dev.platform_data = ixdp425_uart_data,
177 .num_resources = 2,
178 .resource = ixdp425_uart_resources
179 };
180
181 /* Built-in 10/100 Ethernet MAC interfaces */
182 static struct eth_plat_info ixdp425_plat_eth[] = {
183 {
184 .phy = 0,
185 .rxq = 3,
186 .txreadyq = 20,
187 }, {
188 .phy = 1,
189 .rxq = 4,
190 .txreadyq = 21,
191 }
192 };
193
194 static struct platform_device ixdp425_eth[] = {
195 {
196 .name = "ixp4xx_eth",
197 .id = IXP4XX_ETH_NPEB,
198 .dev.platform_data = ixdp425_plat_eth,
199 }, {
200 .name = "ixp4xx_eth",
201 .id = IXP4XX_ETH_NPEC,
202 .dev.platform_data = ixdp425_plat_eth + 1,
203 }
204 };
205
206 static struct platform_device *ixdp425_devices[] __initdata = {
207 &ixdp425_i2c_gpio,
208 &ixdp425_flash,
209 #if defined(CONFIG_MTD_NAND_PLATFORM) || \
210 defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
211 &ixdp425_flash_nand,
212 #endif
213 &ixdp425_uart,
214 &ixdp425_eth[0],
215 &ixdp425_eth[1],
216 };
217
218 static void __init ixdp425_init(void)
219 {
220 ixp4xx_sys_init();
221
222 ixdp425_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
223 ixdp425_flash_resource.end =
224 IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
225
226 #if defined(CONFIG_MTD_NAND_PLATFORM) || \
227 defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
228 ixdp425_flash_nand_resource.start = IXP4XX_EXP_BUS_BASE(3),
229 ixdp425_flash_nand_resource.end = IXP4XX_EXP_BUS_BASE(3) + 0x10 - 1;
230
231 gpio_request(IXDP425_NAND_NCE_PIN, "NAND NCE pin");
232 gpio_direction_output(IXDP425_NAND_NCE_PIN, 0);
233
234 /* Configure expansion bus for NAND Flash */
235 *IXP4XX_EXP_CS3 = IXP4XX_EXP_BUS_CS_EN |
236 IXP4XX_EXP_BUS_STROBE_T(1) | /* extend by 1 clock */
237 IXP4XX_EXP_BUS_CYCLES(0) | /* Intel cycles */
238 IXP4XX_EXP_BUS_SIZE(0) | /* 512bytes addr space*/
239 IXP4XX_EXP_BUS_WR_EN |
240 IXP4XX_EXP_BUS_BYTE_EN; /* 8 bit data bus */
241 #endif
242
243 if (cpu_is_ixp43x()) {
244 ixdp425_uart.num_resources = 1;
245 ixdp425_uart_data[1].flags = 0;
246 }
247
248 platform_add_devices(ixdp425_devices, ARRAY_SIZE(ixdp425_devices));
249 }
250
251 #ifdef CONFIG_ARCH_IXDP425
252 MACHINE_START(IXDP425, "Intel IXDP425 Development Platform")
253 /* Maintainer: MontaVista Software, Inc. */
254 .map_io = ixp4xx_map_io,
255 .init_early = ixp4xx_init_early,
256 .init_irq = ixp4xx_init_irq,
257 .init_time = ixp4xx_timer_init,
258 .atag_offset = 0x100,
259 .init_machine = ixdp425_init,
260 #if defined(CONFIG_PCI)
261 .dma_zone_size = SZ_64M,
262 #endif
263 .restart = ixp4xx_restart,
264 MACHINE_END
265 #endif
266
267 #ifdef CONFIG_MACH_IXDP465
268 MACHINE_START(IXDP465, "Intel IXDP465 Development Platform")
269 /* Maintainer: MontaVista Software, Inc. */
270 .map_io = ixp4xx_map_io,
271 .init_early = ixp4xx_init_early,
272 .init_irq = ixp4xx_init_irq,
273 .init_time = ixp4xx_timer_init,
274 .atag_offset = 0x100,
275 .init_machine = ixdp425_init,
276 #if defined(CONFIG_PCI)
277 .dma_zone_size = SZ_64M,
278 #endif
279 MACHINE_END
280 #endif
281
282 #ifdef CONFIG_ARCH_PRPMC1100
283 MACHINE_START(IXCDP1100, "Intel IXCDP1100 Development Platform")
284 /* Maintainer: MontaVista Software, Inc. */
285 .map_io = ixp4xx_map_io,
286 .init_early = ixp4xx_init_early,
287 .init_irq = ixp4xx_init_irq,
288 .init_time = ixp4xx_timer_init,
289 .atag_offset = 0x100,
290 .init_machine = ixdp425_init,
291 #if defined(CONFIG_PCI)
292 .dma_zone_size = SZ_64M,
293 #endif
294 MACHINE_END
295 #endif
296
297 #ifdef CONFIG_MACH_KIXRP435
298 MACHINE_START(KIXRP435, "Intel KIXRP435 Reference Platform")
299 /* Maintainer: MontaVista Software, Inc. */
300 .map_io = ixp4xx_map_io,
301 .init_early = ixp4xx_init_early,
302 .init_irq = ixp4xx_init_irq,
303 .init_time = ixp4xx_timer_init,
304 .atag_offset = 0x100,
305 .init_machine = ixdp425_init,
306 #if defined(CONFIG_PCI)
307 .dma_zone_size = SZ_64M,
308 #endif
309 MACHINE_END
310 #endif
This page took 0.037969 seconds and 5 git commands to generate.