drivers/input/touchscreen/Kconfig

   1 #
   2 # Touchscreen driver configuration
   3 #
   4 menuconfig INPUT_TOUCHSCREEN
   5         bool "Touchscreens"
   6         help
   7           Say Y here, and a list of supported touchscreens will be displayed.
   8           This option doesn't affect the kernel.
   9
  10           If unsure, say Y.
  11
  12 if INPUT_TOUCHSCREEN
  13
  14 config TOUCHSCREEN_ADS7846
  15         tristate "ADS7846/TSC2046 and ADS7843 based touchscreens"
  16         depends on SPI_MASTER
  17         depends on HWMON = n || HWMON
  18         help
  19           Say Y here if you have a touchscreen interface using the
  20           ADS7846/TSC2046 or ADS7843 controller, and your board-specific
  21           setup code includes that in its table of SPI devices.
  22
  23           If HWMON is selected, and the driver is told the reference voltage
  24           on your board, you will also get hwmon interfaces for the voltage
  25           (and on ads7846/tsc2046, temperature) sensors of this chip.
  26
  27           If unsure, say N (but it's safe to say "Y").
  28
  29           To compile this driver as a module, choose M here: the
  30           module will be called ads7846.
  31
  32 config TOUCHSCREEN_BITSY
  33         tristate "Compaq iPAQ H3600 (Bitsy) touchscreen"
  34         depends on SA1100_BITSY
  35         select SERIO
  36         help
  37           Say Y here if you have the h3600 (Bitsy) touchscreen.
  38
  39           If unsure, say N.
  40
  41           To compile this driver as a module, choose M here: the
  42           module will be called h3600_ts_input.
  43
  44 config TOUCHSCREEN_CORGI
  45         tristate "SharpSL (Corgi and Spitz series) touchscreen driver"
  46         depends on PXA_SHARPSL
  47         default y
  48         help
  49           Say Y here to enable the driver for the touchscreen on the
  50           Sharp SL-C7xx and SL-Cxx00 series of PDAs.
  51
  52           If unsure, say N.
  53
  54           To compile this driver as a module, choose M here: the
  55           module will be called corgi_ts.
  56
  57 config TOUCHSCREEN_FUJITSU
  58         tristate "Fujitsu serial touchscreen"
  59         select SERIO
  60         help
  61           Say Y here if you have the Fujitsu touchscreen (such as one
  62           installed in Lifebook P series laptop) connected to your
  63           system.
  64
  65           If unsure, say N.
  66
  67           To compile this driver as a module, choose M here: the
  68           module will be called fujitsu-ts.
  69
  70 config TOUCHSCREEN_GUNZE
  71         tristate "Gunze AHL-51S touchscreen"
  72         select SERIO
  73         help
  74           Say Y here if you have the Gunze AHL-51 touchscreen connected to
  75           your system.
  76
  77           If unsure, say N.
  78
  79           To compile this driver as a module, choose M here: the
  80           module will be called gunze.
  81
  82 config TOUCHSCREEN_ELO
  83         tristate "Elo serial touchscreens"
  84         select SERIO
  85         help
  86           Say Y here if you have an Elo serial touchscreen connected to
  87           your system.
  88
  89           If unsure, say N.
  90
  91           To compile this driver as a module, choose M here: the
  92           module will be called elo.
  93
  94 config TOUCHSCREEN_MTOUCH
  95         tristate "MicroTouch serial touchscreens"
  96         select SERIO
  97         help
  98           Say Y here if you have a MicroTouch (3M) serial touchscreen connected to
  99           your system.
 100
 101           If unsure, say N.
 102
 103           To compile this driver as a module, choose M here: the
 104           module will be called mtouch.
 105
 106 config TOUCHSCREEN_MK712
 107         tristate "ICS MicroClock MK712 touchscreen"
 108         help
 109           Say Y here if you have the ICS MicroClock MK712 touchscreen
 110           controller chip in your system.
 111
 112           If unsure, say N.
 113
 114           To compile this driver as a module, choose M here: the
 115           module will be called mk712.
 116
 117 config TOUCHSCREEN_HP600
 118         tristate "HP Jornada 6xx touchscreen"
 119         depends on SH_HP6XX && SH_ADC
 120         help
 121           Say Y here if you have a HP Jornada 620/660/680/690 and want to
 122           support the built-in touchscreen.
 123
 124           To compile this driver as a module, choose M here: the
 125           module will be called hp680_ts_input.
 126
 127 config TOUCHSCREEN_HP7XX
 128         tristate "HP Jornada 7xx touchscreen"
 129         depends on SA1100_JORNADA720_SSP
 130         help
 131           Say Y here if you have a HP Jornada 710/720/728 and want
 132           to support the built-in touchscreen.
 133
 134           To compile this driver as a module, choose M here: the
 135           module will be called jornada720_ts.
 136
 137 config TOUCHSCREEN_PENMOUNT
 138         tristate "Penmount serial touchscreen"
 139         select SERIO
 140         help
 141           Say Y here if you have a Penmount serial touchscreen connected to
 142           your system.
 143
 144           If unsure, say N.
 145
 146           To compile this driver as a module, choose M here: the
 147           module will be called penmount.
 148
 149 config TOUCHSCREEN_TOUCHRIGHT
 150         tristate "Touchright serial touchscreen"
 151         select SERIO
 152         help
 153           Say Y here if you have a Touchright serial touchscreen connected to
 154           your system.
 155
 156           If unsure, say N.
 157
 158           To compile this driver as a module, choose M here: the
 159           module will be called touchright.
 160
 161 config TOUCHSCREEN_TOUCHWIN
 162         tristate "Touchwin serial touchscreen"
 163         select SERIO
 164         help
 165           Say Y here if you have a Touchwin serial touchscreen connected to
 166           your system.
 167
 168           If unsure, say N.
 169
 170           To compile this driver as a module, choose M here: the
 171           module will be called touchwin.
 172
 173 config TOUCHSCREEN_UCB1400
 174         tristate "Philips UCB1400 touchscreen"
 175         select AC97_BUS
 176         help
 177           This enables support for the Philips UCB1400 touchscreen interface.
 178           The UCB1400 is an AC97 audio codec.  The touchscreen interface
 179           will be initialized only after the ALSA subsystem has been
 180           brought up and the UCB1400 detected.  You therefore have to
 181           configure ALSA support as well (either built-in or modular,
 182           independently of whether this driver is itself built-in or
 183           modular) for this driver to work.
 184
 185           To compile this driver as a module, choose M here: the
 186           module will be called ucb1400_ts.
 187
 188 config TOUCHSCREEN_WM97XX
 189         tristate "Support for WM97xx AC97 touchscreen controllers"
 190         depends on AC97_BUS
 191         help
 192           Say Y here if you have a Wolfson Microelectronics WM97xx
 193           touchscreen connected to your system. Note that this option
 194           only enables core driver, you will also need to select
 195           support for appropriate chip below.
 196
 197           If unsure, say N.
 198
 199           To compile this driver as a module, choose M here: the
 200           module will be called wm97xx-ts.
 201
 202 config TOUCHSCREEN_WM9705
 203         bool "WM9705 Touchscreen interface support"
 204         depends on TOUCHSCREEN_WM97XX
 205         help
 206           Say Y here if you have a Wolfson Microelectronics WM9705
 207           touchscreen controller connected to your system.
 208
 209           If unsure, say N.
 210
 211 config TOUCHSCREEN_WM9712
 212         bool "WM9712 Touchscreen interface support"
 213         depends on TOUCHSCREEN_WM97XX
 214         help
 215           Say Y here if you have a Wolfson Microelectronics WM9712
 216           touchscreen controller connected to your system.
 217
 218           If unsure, say N.
 219
 220 config TOUCHSCREEN_WM9713
 221         bool "WM9713 Touchscreen interface support"
 222         depends on TOUCHSCREEN_WM97XX
 223         help
 224           Say Y here if you have a Wolfson Microelectronics WM9713 touchscreen
 225           controller connected to your system.
 226
 227           If unsure, say N.
 228
 229 config TOUCHSCREEN_WM97XX_MAINSTONE
 230         tristate "WM97xx Mainstone accelerated touch"
 231         depends on TOUCHSCREEN_WM97XX && ARCH_PXA
 232         help
 233           Say Y here for support for streaming mode with WM97xx touchscreens
 234           on Mainstone systems.
 235
 236           If unsure, say N.
 237
 238           To compile this driver as a module, choose M here: the
 239           module will be called mainstone-wm97xx.
 240
 241 config TOUCHSCREEN_USB_COMPOSITE
 242         tristate "USB Touchscreen Driver"
 243         depends on USB_ARCH_HAS_HCD
 244         select USB
 245         help
 246           USB Touchscreen driver for:
 247           - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700)
 248           - PanJit TouchSet USB
 249           - 3M MicroTouch USB (EX II series)
 250           - ITM
 251           - some other eTurboTouch
 252           - Gunze AHL61
 253           - DMC TSC-10/25
 254           - IRTOUCHSYSTEMS/UNITOP
 255           - IdealTEK URTC1000
 256           - GoTop Super_Q2/GogoPen/PenPower tablets
 257
 258           Have a look at <http://linux.chapter7.ch/touchkit/> for
 259           a usage description and the required user-space stuff.
 260
 261           To compile this driver as a module, choose M here: the
 262           module will be called usbtouchscreen.
 263
 264 config TOUCHSCREEN_USB_EGALAX
 265         default y
 266         bool "eGalax, eTurboTouch CT-410/510/700 device support" if EMBEDDED
 267         depends on TOUCHSCREEN_USB_COMPOSITE
 268
 269 config TOUCHSCREEN_USB_PANJIT
 270         default y
 271         bool "PanJit device support" if EMBEDDED
 272         depends on TOUCHSCREEN_USB_COMPOSITE
 273
 274 config TOUCHSCREEN_USB_3M
 275         default y
 276         bool "3M/Microtouch EX II series device support" if EMBEDDED
 277         depends on TOUCHSCREEN_USB_COMPOSITE
 278
 279 config TOUCHSCREEN_USB_ITM
 280         default y
 281         bool "ITM device support" if EMBEDDED
 282         depends on TOUCHSCREEN_USB_COMPOSITE
 283
 284 config TOUCHSCREEN_USB_ETURBO
 285         default y
 286         bool "eTurboTouch (non-eGalax compatible) device support" if EMBEDDED
 287         depends on TOUCHSCREEN_USB_COMPOSITE
 288
 289 config TOUCHSCREEN_USB_GUNZE
 290         default y
 291         bool "Gunze AHL61 device support" if EMBEDDED
 292         depends on TOUCHSCREEN_USB_COMPOSITE
 293
 294 config TOUCHSCREEN_USB_DMC_TSC10
 295         default y
 296         bool "DMC TSC-10/25 device support" if EMBEDDED
 297         depends on TOUCHSCREEN_USB_COMPOSITE
 298
 299 config TOUCHSCREEN_USB_IRTOUCH
 300         default y
 301         bool "IRTOUCHSYSTEMS/UNITOP device support" if EMBEDDED
 302         depends on TOUCHSCREEN_USB_COMPOSITE
 303
 304 config TOUCHSCREEN_USB_IDEALTEK
 305         default y
 306         bool "IdealTEK URTC1000 device support" if EMBEDDED
 307         depends on TOUCHSCREEN_USB_COMPOSITE
 308
 309 config TOUCHSCREEN_USB_GENERAL_TOUCH
 310         default y
 311         bool "GeneralTouch Touchscreen device support" if EMBEDDED
 312         depends on TOUCHSCREEN_USB_COMPOSITE
 313
 314 config TOUCHSCREEN_USB_GOTOP
 315         default y
 316         bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EMBEDDED
 317         depends on TOUCHSCREEN_USB_COMPOSITE
 318
 319 endif