drivers/misc/Kconfig

   1 #
   2 # Misc strange devices
   3 #
   4
   5 menuconfig MISC_DEVICES
   6         bool "Misc devices"
   7         default y
   8         ---help---
   9           Say Y here to get to see options for device drivers from various
  10           different categories. This option alone does not add any kernel code.
  11
  12           If you say N, all options in this submenu will be skipped and disabled.
  13
  14 if MISC_DEVICES
  15
  16 config ATMEL_PWM
  17         tristate "Atmel AT32/AT91 PWM support"
  18         depends on AVR32 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9
  19         help
  20           This option enables device driver support for the PWM channels
  21           on certain Atmel prcoessors.  Pulse Width Modulation is used for
  22           purposes including software controlled power-efficent backlights
  23           on LCD displays, motor control, and waveform generation.
  24
  25 config ATMEL_TCLIB
  26         bool "Atmel AT32/AT91 Timer/Counter Library"
  27         depends on (AVR32 || ARCH_AT91)
  28         help
  29           Select this if you want a library to allocate the Timer/Counter
  30           blocks found on many Atmel processors.  This facilitates using
  31           these blocks by different drivers despite processor differences.
  32
  33 config ATMEL_TCB_CLKSRC
  34         bool "TC Block Clocksource"
  35         depends on ATMEL_TCLIB && GENERIC_TIME
  36         default y
  37         help
  38           Select this to get a high precision clocksource based on a
  39           TC block with a 5+ MHz base clock rate.  Two timer channels
  40           are combined to make a single 32-bit timer.
  41
  42           When GENERIC_CLOCKEVENTS is defined, the third timer channel
  43           may be used as a clock event device supporting oneshot mode
  44           (delays of up to two seconds) based on the 32 KiHz clock.
  45
  46 config ATMEL_TCB_CLKSRC_BLOCK
  47         int
  48         depends on ATMEL_TCB_CLKSRC
  49         prompt "TC Block" if ARCH_AT91RM9200 || ARCH_AT91SAM9260 || CPU_AT32AP700X
  50         default 0
  51         range 0 1
  52         help
  53           Some chips provide more than one TC block, so you have the
  54           choice of which one to use for the clock framework.  The other
  55           TC can be used for other purposes, such as PWM generation and
  56           interval timing.
  57
  58 config IBM_ASM
  59         tristate "Device driver for IBM RSA service processor"
  60         depends on X86 && PCI && INPUT && EXPERIMENTAL
  61         ---help---
  62           This option enables device driver support for in-band access to the
  63           IBM RSA (Condor) service processor in eServer xSeries systems.
  64           The ibmasm device driver allows user space application to access
  65           ASM (Advanced Systems Management) functions on the service
  66           processor. The driver is meant to be used in conjunction with
  67           a user space API.
  68           The ibmasm driver also enables the OS to use the UART on the
  69           service processor board as a regular serial port. To make use of
  70           this feature serial driver support (CONFIG_SERIAL_8250) must be
  71           enabled.
  72
  73           WARNING: This software may not be supported or function
  74           correctly on your IBM server. Please consult the IBM ServerProven
  75           website <http://www.pc.ibm.com/ww/eserver/xseries/serverproven> for
  76           information on the specific driver level and support statement
  77           for your IBM server.
  78
  79 config PHANTOM
  80         tristate "Sensable PHANToM (PCI)"
  81         depends on PCI
  82         help
  83           Say Y here if you want to build a driver for Sensable PHANToM device.
  84
  85           This driver is only for PCI PHANToMs.
  86
  87           If you choose to build module, its name will be phantom. If unsure,
  88           say N here.
  89
  90 config EEPROM_93CX6
  91         tristate "EEPROM 93CX6 support"
  92         ---help---
  93           This is a driver for the EEPROM chipsets 93c46 and 93c66.
  94           The driver supports both read as well as write commands.
  95
  96           If unsure, say N.
  97
  98 config SGI_IOC4
  99         tristate "SGI IOC4 Base IO support"
 100         depends on PCI
 101         ---help---
 102           This option enables basic support for the IOC4 chip on certain
 103           SGI IO controller cards (IO9, IO10, and PCI-RT).  This option
 104           does not enable any specific functions on such a card, but provides
 105           necessary infrastructure for other drivers to utilize.
 106
 107           If you have an SGI Altix with an IOC4-based card say Y.
 108           Otherwise say N.
 109
 110 config TIFM_CORE
 111         tristate "TI Flash Media interface support (EXPERIMENTAL)"
 112         depends on EXPERIMENTAL && PCI
 113         help
 114           If you want support for Texas Instruments(R) Flash Media adapters
 115           you should select this option and then also choose an appropriate
 116           host adapter, such as 'TI Flash Media PCI74xx/PCI76xx host adapter
 117           support', if you have a TI PCI74xx compatible card reader, for
 118           example.
 119           You will also have to select some flash card format drivers. MMC/SD
 120           cards are supported via 'MMC/SD Card support: TI Flash Media MMC/SD
 121           Interface support (MMC_TIFM_SD)'.
 122
 123           To compile this driver as a module, choose M here: the module will
 124           be called tifm_core.
 125
 126 config TIFM_7XX1
 127         tristate "TI Flash Media PCI74xx/PCI76xx host adapter support (EXPERIMENTAL)"
 128         depends on PCI && TIFM_CORE && EXPERIMENTAL
 129         default TIFM_CORE
 130         help
 131           This option enables support for Texas Instruments(R) PCI74xx and
 132           PCI76xx families of Flash Media adapters, found in many laptops.
 133           To make actual use of the device, you will have to select some
 134           flash card format drivers, as outlined in the TIFM_CORE Help.
 135
 136           To compile this driver as a module, choose M here: the module will
 137           be called tifm_7xx1.
 138
 139 config ICS932S401
 140         tristate "Integrated Circuits ICS932S401"
 141         depends on I2C && EXPERIMENTAL
 142         help
 143           If you say yes here you get support for the Integrated Circuits
 144           ICS932S401 clock control chips.
 145
 146           This driver can also be built as a module. If so, the module
 147           will be called ics932s401.
 148
 149 config ATMEL_SSC
 150         tristate "Device driver for Atmel SSC peripheral"
 151         depends on AVR32 || ARCH_AT91
 152         ---help---
 153           This option enables device driver support for Atmel Syncronized
 154           Serial Communication peripheral (SSC).
 155
 156           The SSC peripheral supports a wide variety of serial frame based
 157           communications, i.e. I2S, SPI, etc.
 158
 159           If unsure, say N.
 160
 161 config ENCLOSURE_SERVICES
 162         tristate "Enclosure Services"
 163         default n
 164         help
 165           Provides support for intelligent enclosures (bays which
 166           contain storage devices).  You also need either a host
 167           driver (SCSI/ATA) which supports enclosures
 168           or a SCSI enclosure device (SES) to use these services.
 169
 170 config SGI_XP
 171         tristate "Support communication between SGI SSIs"
 172         depends on NET
 173         depends on (IA64_GENERIC || IA64_SGI_SN2 || IA64_SGI_UV || X86_64) && SMP
 174         select IA64_UNCACHED_ALLOCATOR if IA64_GENERIC || IA64_SGI_SN2
 175         select GENERIC_ALLOCATOR if IA64_GENERIC || IA64_SGI_SN2
 176         select SGI_GRU if (IA64_GENERIC || IA64_SGI_UV || X86_64) && SMP
 177         ---help---
 178           An SGI machine can be divided into multiple Single System
 179           Images which act independently of each other and have
 180           hardware based memory protection from the others.  Enabling
 181           this feature will allow for direct communication between SSIs
 182           based on a network adapter and DMA messaging.
 183
 184 config HP_ILO
 185         tristate "Channel interface driver for HP iLO/iLO2 processor"
 186         depends on PCI
 187         default n
 188         help
 189           The channel interface driver allows applications to communicate
 190           with iLO/iLO2 management processors present on HP ProLiant
 191           servers.  Upon loading, the driver creates /dev/hpilo/dXccbN files,
 192           which can be used to gather data from the management processor,
 193           via read and write system calls.
 194
 195           To compile this driver as a module, choose M here: the
 196           module will be called hpilo.
 197
 198 config SGI_GRU
 199         tristate "SGI GRU driver"
 200         depends on (X86_64 || IA64_SGI_UV || IA64_GENERIC) && SMP
 201         default n
 202         select MMU_NOTIFIER
 203         ---help---
 204         The GRU is a hardware resource located in the system chipset. The GRU
 205         contains memory that can be mmapped into the user address space. This memory is
 206         used to communicate with the GRU to perform functions such as load/store,
 207         scatter/gather, bcopy, AMOs, etc.  The GRU is directly accessed by user
 208         instructions using user virtual addresses. GRU instructions (ex., bcopy) use
 209         user virtual addresses for operands.
 210
 211         If you are not running on a SGI UV system, say N.
 212
 213 config SGI_GRU_DEBUG
 214         bool  "SGI GRU driver debug"
 215         depends on SGI_GRU
 216         default n
 217         ---help---
 218         This option enables addition debugging code for the SGI GRU driver. If
 219         you are unsure, say N.
 220
 221 config DELL_LAPTOP
 222         tristate "Dell Laptop Extras (EXPERIMENTAL)"
 223         depends on X86
 224         depends on DCDBAS
 225         depends on EXPERIMENTAL
 226         depends on BACKLIGHT_CLASS_DEVICE
 227         depends on RFKILL
 228         default n
 229         ---help---
 230         This driver adds support for rfkill and backlight control to Dell
 231         laptops.
 232
 233 source "drivers/misc/c2port/Kconfig"
 234
 235 endif # MISC_DEVICES