1 /*********************************************************
3 * Definition of D-Link DE-620 Ethernet Pocket adapter *
5 *********************************************************/
7 /* DE-620's CMD port Command */
8 #define CS0 0x08 /* 1->0 command strobe */
9 #define ICEN 0x04 /* 0=enable DL3520 host interface */
10 #define DS0 0x02 /* 1->0 data strobe 0 */
11 #define DS1 0x01 /* 1->0 data strobe 1 */
13 #define WDIR 0x20 /* general 0=read 1=write */
14 #define RDIR 0x00 /* (not 100% confirm ) */
15 #define PS2WDIR 0x00 /* ps/2 mode 1=read, 0=write */
18 #define IRQEN 0x10 /* 1 = enable printer IRQ line */
19 #define SELECTIN 0x08 /* 1 = select printer */
20 #define INITP 0x04 /* 0 = initial printer */
21 #define AUTOFEED 0x02 /* 1 = printer auto form feed */
22 #define STROBE 0x01 /* 0->1 data strobe */
25 #define NIS0 0x20 /* 0 = BNC, 1 = UTP */
28 /* DE-620 DIC Command */
29 #define W_DUMMY 0x00 /* DIC reserved command */
30 #define W_CR 0x20 /* DIC write command register */
31 #define W_NPR 0x40 /* DIC write Next Page Register */
32 #define W_TBR 0x60 /* DIC write Tx Byte Count 1 reg */
33 #define W_RSA 0x80 /* DIC write Remote Start Addr 1 */
35 /* DE-620's STAT port bits 7-4 */
36 #define EMPTY 0x80 /* 1 = receive buffer empty */
37 #define INTLEVEL 0x40 /* 1 = interrupt level is high */
38 #define TXBF1 0x20 /* 1 = transmit buffer 1 is in use */
39 #define TXBF0 0x10 /* 1 = transmit buffer 0 is in use */
40 #define READY 0x08 /* 1 = h/w ready to accept cmd/data */
43 #define W_RSA1 0xa0 /* write remote start address 1 */
44 #define W_RSA0 0xa1 /* write remote start address 0 */
45 #define W_NPRF 0xa2 /* write next page register NPR15-NPR8 */
46 #define W_DFR 0xa3 /* write delay factor register */
47 #define W_CPR 0xa4 /* write current page register */
48 #define W_SPR 0xa5 /* write start page register */
49 #define W_EPR 0xa6 /* write end page register */
50 #define W_SCR 0xa7 /* write system configuration register */
51 #define W_TCR 0xa8 /* write Transceiver Configuration reg */
52 #define W_EIP 0xa9 /* write EEPM Interface port */
53 #define W_PAR0 0xaa /* write physical address register 0 */
54 #define W_PAR1 0xab /* write physical address register 1 */
55 #define W_PAR2 0xac /* write physical address register 2 */
56 #define W_PAR3 0xad /* write physical address register 3 */
57 #define W_PAR4 0xae /* write physical address register 4 */
58 #define W_PAR5 0xaf /* write physical address register 5 */
61 #define R_STS 0xc0 /* read status register */
62 #define R_CPR 0xc1 /* read current page register */
63 #define R_BPR 0xc2 /* read boundary page register */
64 #define R_TDR 0xc3 /* read time domain reflectometry reg */
67 #define EEDI 0x80 /* EEPM DO pin */
68 #define TXSUC 0x40 /* tx success */
69 #define T16 0x20 /* tx fail 16 times */
70 #define TS1 0x40 /* 0=Tx success, 1=T16 */
71 #define TS0 0x20 /* 0=Tx success, 1=T16 */
72 #define RXGOOD 0x10 /* rx a good packet */
73 #define RXCRC 0x08 /* rx a CRC error packet */
74 #define RXSHORT 0x04 /* rx a short packet */
75 #define COLS 0x02 /* coaxial collision status */
76 #define LNKS 0x01 /* UTP link status */
78 /* Command Register */
79 #define CLEAR 0x10 /* reset part of hardware */
80 #define NOPER 0x08 /* No Operation */
82 #define RRA 0x06 /* After RR then auto-advance NPR & BPR(=NPR-1) */
83 #define RRN 0x04 /* Normal Remote Read mode */
84 #define RW1 0x02 /* Remote Write tx buffer 1 ( page 6 - 11 ) */
85 #define RW0 0x00 /* Remote Write tx buffer 0 ( page 0 - 5 ) */
86 #define TXEN 0x01 /* 0->1 tx enable */
88 /* System Configuration Register */
89 #define TESTON 0x80 /* test host data transfer reliability */
90 #define SLEEP 0x40 /* sleep mode */
92 #define FASTMODE 0x04 /* fast mode for intel 82360SL fast mode */
93 #define BYTEMODE 0x02 /* byte mode */
95 #define FASTMODE 0x20 /* fast mode for intel 82360SL fast mode */
96 #define BYTEMODE 0x10 /* byte mode */
98 #define NIBBLEMODE 0x00 /* nibble mode */
99 #define IRQINV 0x08 /* turn off IRQ line inverter */
100 #define IRQNML 0x00 /* turn on IRQ line inverter */
102 #define AUTOFFSET 0x02 /* auto shift address to TPR+12 */
103 #define AUTOTX 0x01 /* auto tx when leave RW mode */
105 /* Transceiver Configuration Register */
106 #define JABBER 0x80 /* generate jabber condition */
107 #define TXSUCINT 0x40 /* enable tx success interrupt */
108 #define T16INT 0x20 /* enable T16 interrupt */
109 #define RXERRPKT 0x10 /* accept CRC error or short packet */
110 #define EXTERNALB2 0x0C /* external loopback 2 */
111 #define EXTERNALB1 0x08 /* external loopback 1 */
112 #define INTERNALB 0x04 /* internal loopback */
113 #define NMLOPERATE 0x00 /* normal operation */
114 #define RXPBM 0x03 /* rx physical, broadcast, multicast */
115 #define RXPB 0x02 /* rx physical, broadcast */
116 #define RXALL 0x01 /* rx all packet */
117 #define RXOFF 0x00 /* rx disable */
This page took 0.03371 seconds and 5 git commands to generate.