2 * eexpress.h: Intel EtherExpress16 defines
6 * EtherExpress card register addresses
7 * as offsets from the base IO region (dev->base_addr)
10 #define DATAPORT 0x0000
11 #define WRITE_PTR 0x0002
12 #define READ_PTR 0x0004
13 #define SIGNAL_CA 0x0006
14 #define SET_IRQ 0x0007
16 #define MEM_Dec 0x000a
17 #define MEM_Ctrl 0x000b
18 #define MEM_Page_Ctrl 0x000c
20 #define EEPROM_Ctrl 0x000e
21 #define ID_PORT 0x000f
22 #define MEM_ECtrl 0x000f
25 * card register defines
40 #define eeprom_delay() { udelay(40); }
43 * i82586 Memory Configuration
46 /* (System Configuration Pointer) System start up block, read after 586_RST */
47 #define SCP_START 0xfff6
49 /* Intermediate System Configuration Pointer */
50 #define ISCP_START 0x0000
52 /* System Command Block */
53 #define SCB_START 0x0008
55 /* Start of buffer region. Everything before this is used for control
56 * structures and the CU configuration program. The memory layout is
57 * determined in eexp_hw_probe(), once we know how much memory is
58 * available on the card.
61 #define TX_BUF_START 0x0100
63 #define TX_BUF_SIZE ((24+ETH_FRAME_LEN+31)&~0x1f)
64 #define RX_BUF_SIZE ((32+ETH_FRAME_LEN+31)&~0x1f)
70 /* these functions take the SCB status word and test the relevant status bit */
71 #define SCB_complete(s) (((s) & 0x8000) != 0)
72 #define SCB_rxdframe(s) (((s) & 0x4000) != 0)
73 #define SCB_CUdead(s) (((s) & 0x2000) != 0)
74 #define SCB_RUdead(s) (((s) & 0x1000) != 0)
75 #define SCB_ack(s) ((s) & 0xf000)
77 /* Command unit status: 0=idle, 1=suspended, 2=active */
78 #define SCB_CUstat(s) (((s)&0x0300)>>8)
80 /* Receive unit status: 0=idle, 1=suspended, 2=out of resources, 4=ready */
81 #define SCB_RUstat(s) (((s)&0x0070)>>4)
84 #define SCB_CUnop 0x0000
85 #define SCB_CUstart 0x0100
86 #define SCB_CUresume 0x0200
87 #define SCB_CUsuspend 0x0300
88 #define SCB_CUabort 0x0400
89 #define SCB_resetchip 0x0080
91 #define SCB_RUnop 0x0000
92 #define SCB_RUstart 0x0010
93 #define SCB_RUresume 0x0020
94 #define SCB_RUsuspend 0x0030
95 #define SCB_RUabort 0x0040
98 * Command block defines
101 #define Stat_Done(s) (((s) & 0x8000) != 0)
102 #define Stat_Busy(s) (((s) & 0x4000) != 0)
103 #define Stat_OK(s) (((s) & 0x2000) != 0)
104 #define Stat_Abort(s) (((s) & 0x1000) != 0)
105 #define Stat_STFail (((s) & 0x0800) != 0)
106 #define Stat_TNoCar(s) (((s) & 0x0400) != 0)
107 #define Stat_TNoCTS(s) (((s) & 0x0200) != 0)
108 #define Stat_TNoDMA(s) (((s) & 0x0100) != 0)
109 #define Stat_TDefer(s) (((s) & 0x0080) != 0)
110 #define Stat_TColl(s) (((s) & 0x0040) != 0)
111 #define Stat_TXColl(s) (((s) & 0x0020) != 0)
112 #define Stat_NoColl(s) ((s) & 0x000f)
114 /* Cmd_END will end AFTER the command if this is the first
115 * command block after an SCB_CUstart, but BEFORE the command
116 * for all subsequent commands. Best strategy is to place
117 * Cmd_INT on the last command in the sequence, followed by a
118 * dummy Cmd_Nop with Cmd_END after this.
121 #define Cmd_END 0x8000
122 #define Cmd_SUS 0x4000
123 #define Cmd_INT 0x2000
125 #define Cmd_Nop 0x0000
126 #define Cmd_SetAddr 0x0001
127 #define Cmd_Config 0x0002
128 #define Cmd_MCast 0x0003
129 #define Cmd_Xmit 0x0004
130 #define Cmd_TDR 0x0005
131 #define Cmd_Dump 0x0006
132 #define Cmd_Diag 0x0007
136 * Frame Descriptor (Receive block) defines
139 #define FD_Done(s) (((s) & 0x8000) != 0)
140 #define FD_Busy(s) (((s) & 0x4000) != 0)
141 #define FD_OK(s) (((s) & 0x2000) != 0)
143 #define FD_CRC(s) (((s) & 0x0800) != 0)
144 #define FD_Align(s) (((s) & 0x0400) != 0)
145 #define FD_Resrc(s) (((s) & 0x0200) != 0)
146 #define FD_DMA(s) (((s) & 0x0100) != 0)
147 #define FD_Short(s) (((s) & 0x0080) != 0)
148 #define FD_NoEOF(s) (((s) & 0x0040) != 0)
151 volatile unsigned long flags
;
152 volatile unsigned short link
;
153 volatile unsigned short rbd_offset
;
154 volatile unsigned short dstaddr1
;
155 volatile unsigned short dstaddr2
;
156 volatile unsigned short dstaddr3
;
157 volatile unsigned short srcaddr1
;
158 volatile unsigned short srcaddr2
;
159 volatile unsigned short srcaddr3
;
160 volatile unsigned short length
;
162 /* This is actually a Receive Buffer Descriptor. The way we
163 * arrange memory means that an RBD always follows the RFD that
164 * points to it, so they might as well be in the same structure.
166 volatile unsigned short actual_count
;
167 volatile unsigned short next_rbd
;
168 volatile unsigned short buf_addr1
;
169 volatile unsigned short buf_addr2
;
170 volatile unsigned short size
;
173 /* Returned data from the Time Domain Reflectometer */
175 #define TDR_LINKOK (1<<15)
176 #define TDR_XCVRPROBLEM (1<<14)
177 #define TDR_OPEN (1<<13)
178 #define TDR_SHORT (1<<12)
179 #define TDR_TIME 0x7ff
This page took 0.032988 seconds and 5 git commands to generate.