2 * drivers/net/phy/qsemi.c
4 * Driver for Quality Semiconductor PHYs
8 * Copyright (c) 2004 Freescale Semiconductor, Inc.
10 * This program is free software; you can redistribute it and/or modify it
11 * under the terms of the GNU General Public License as published by the
12 * Free Software Foundation; either version 2 of the License, or (at your
13 * option) any later version.
16 #include <linux/kernel.h>
17 #include <linux/string.h>
18 #include <linux/errno.h>
19 #include <linux/unistd.h>
20 #include <linux/slab.h>
21 #include <linux/interrupt.h>
22 #include <linux/init.h>
23 #include <linux/delay.h>
24 #include <linux/netdevice.h>
25 #include <linux/etherdevice.h>
26 #include <linux/skbuff.h>
27 #include <linux/spinlock.h>
29 #include <linux/module.h>
30 #include <linux/mii.h>
31 #include <linux/ethtool.h>
32 #include <linux/phy.h>
36 #include <asm/uaccess.h>
38 /* ------------------------------------------------------------------------- */
39 /* The Quality Semiconductor QS6612 is used on the RPX CLLF */
41 /* register definitions */
43 #define MII_QS6612_MCR 17 /* Mode Control Register */
44 #define MII_QS6612_FTR 27 /* Factory Test Register */
45 #define MII_QS6612_MCO 28 /* Misc. Control Register */
46 #define MII_QS6612_ISR 29 /* Interrupt Source Register */
47 #define MII_QS6612_IMR 30 /* Interrupt Mask Register */
48 #define MII_QS6612_IMR_INIT 0x003a
49 #define MII_QS6612_PCR 31 /* 100BaseTx PHY Control Reg. */
51 #define QS6612_PCR_AN_COMPLETE 0x1000
52 #define QS6612_PCR_RLBEN 0x0200
53 #define QS6612_PCR_DCREN 0x0100
54 #define QS6612_PCR_4B5BEN 0x0040
55 #define QS6612_PCR_TX_ISOLATE 0x0020
56 #define QS6612_PCR_MLT3_DIS 0x0002
57 #define QS6612_PCR_SCRM_DESCRM 0x0001
59 MODULE_DESCRIPTION("Quality Semiconductor PHY driver");
60 MODULE_AUTHOR("Andy Fleming");
61 MODULE_LICENSE("GPL");
63 /* Returns 0, unless there's a write error */
64 static int qs6612_config_init(struct phy_device
*phydev
)
66 /* The PHY powers up isolated on the RPX,
67 * so send a command to allow operation.
68 * XXX - My docs indicate this should be 0x0940
69 * ...or something. The current value sets three
70 * reserved bits, bit 11, which specifies it should be
71 * set to one, bit 10, which specifies it should be set
72 * to 0, and bit 7, which doesn't specify. However, my
73 * docs are preliminary, and I will leave it like this
74 * until someone more knowledgable corrects me or it.
77 return phy_write(phydev
, MII_QS6612_PCR
, 0x0dc0);
80 static int qs6612_ack_interrupt(struct phy_device
*phydev
)
84 err
= phy_read(phydev
, MII_QS6612_ISR
);
89 err
= phy_read(phydev
, MII_BMSR
);
94 err
= phy_read(phydev
, MII_EXPANSION
);
102 static int qs6612_config_intr(struct phy_device
*phydev
)
105 if (phydev
->interrupts
== PHY_INTERRUPT_ENABLED
)
106 err
= phy_write(phydev
, MII_QS6612_IMR
,
107 MII_QS6612_IMR_INIT
);
109 err
= phy_write(phydev
, MII_QS6612_IMR
, 0);
115 static struct phy_driver qs6612_driver
= {
116 .phy_id
= 0x00181440,
118 .phy_id_mask
= 0xfffffff0,
119 .features
= PHY_BASIC_FEATURES
,
120 .flags
= PHY_HAS_INTERRUPT
,
121 .config_init
= qs6612_config_init
,
122 .config_aneg
= genphy_config_aneg
,
123 .read_status
= genphy_read_status
,
124 .ack_interrupt
= qs6612_ack_interrupt
,
125 .config_intr
= qs6612_config_intr
,
126 .driver
= { .owner
= THIS_MODULE
,},
129 static int __init
qs6612_init(void)
131 return phy_driver_register(&qs6612_driver
);
134 static void __exit
qs6612_exit(void)
136 phy_driver_unregister(&qs6612_driver
);
139 module_init(qs6612_init
);
140 module_exit(qs6612_exit
);
This page took 0.032589 seconds and 5 git commands to generate.