2 * mac53c94.h: definitions for the driver for the 53c94 SCSI bus adaptor
3 * found on Power Macintosh computers, controlling the external SCSI chain.
5 * Copyright (C) 1996 Paul Mackerras.
11 * Registers in the 53C94 controller.
14 struct mac53c94_regs
{
15 unsigned char count_lo
;
17 unsigned char count_mid
;
21 unsigned char command
;
25 unsigned char interrupt
;
27 unsigned char seqstep
;
31 unsigned char config1
;
33 unsigned char clk_factor
;
37 unsigned char config2
;
39 unsigned char config3
;
41 unsigned char config4
;
43 unsigned char count_hi
;
45 unsigned char fifo_res
;
50 * Alternate functions for some registers.
52 #define dest_id status
53 #define sel_timeout interrupt
54 #define sync_period seqstep
55 #define sync_offset flags
58 * Bits in command register.
60 #define CMD_DMA_MODE 0x80
61 #define CMD_MODE_MASK 0x70
62 #define CMD_MODE_INIT 0x10
63 #define CMD_MODE_TARG 0x20
64 #define CMD_MODE_DISC 0x40
69 #define CMD_SCSI_RESET 3
71 #define CMD_XFER_DATA 0x10
72 #define CMD_I_COMPLETE 0x11
73 #define CMD_ACCEPT_MSG 0x12
74 #define CMD_XFER_PAD 0x18
75 #define CMD_SET_ATN 0x1a
76 #define CMD_CLR_ATN 0x1b
78 #define CMD_SEND_MSG 0x20
79 #define CMD_SEND_STATUS 0x21
80 #define CMD_SEND_DATA 0x22
81 #define CMD_DISC_SEQ 0x23
82 #define CMD_TERMINATE 0x24
83 #define CMD_T_COMPLETE 0x25
84 #define CMD_DISCONNECT 0x27
85 #define CMD_RECV_MSG 0x28
86 #define CMD_RECV_CDB 0x29
87 #define CMD_RECV_DATA 0x2a
88 #define CMD_RECV_CMD 0x2b
89 #define CMD_ABORT_DMA 0x04
91 #define CMD_RESELECT 0x40
92 #define CMD_SELECT 0x41
93 #define CMD_SELECT_ATN 0x42
94 #define CMD_SELATN_STOP 0x43
95 #define CMD_ENABLE_SEL 0x44
96 #define CMD_DISABLE_SEL 0x45
97 #define CMD_SEL_ATN3 0x46
98 #define CMD_RESEL_ATN3 0x47
101 * Bits in status register.
103 #define STAT_IRQ 0x80
104 #define STAT_ERROR 0x40
105 #define STAT_PARITY 0x20
106 #define STAT_TC_ZERO 0x10
107 #define STAT_DONE 0x08
108 #define STAT_PHASE 0x07
109 #define STAT_MSG 0x04
114 * Bits in interrupt register.
116 #define INTR_RESET 0x80 /* SCSI bus was reset */
117 #define INTR_ILL_CMD 0x40 /* illegal command */
118 #define INTR_DISCONNECT 0x20 /* we got disconnected */
119 #define INTR_BUS_SERV 0x10 /* bus service requested */
120 #define INTR_DONE 0x08 /* function completed */
121 #define INTR_RESELECTED 0x04 /* we were reselected */
122 #define INTR_SEL_ATN 0x02 /* we were selected, ATN asserted */
123 #define INTR_SELECT 0x01 /* we were selected, ATN negated */
126 * Encoding for the select timeout.
128 #define TIMO_VAL(x) ((x) * 5000 / 7682)
131 * Bits in sequence step register.
134 #define SS_ARB_SEL 0 /* Selection & arbitration complete */
135 #define SS_MSG_SENT 1 /* One message byte sent */
136 #define SS_NOT_CMD 2 /* Not in command phase */
137 #define SS_PHASE_CHG 3 /* Early phase change, cmd bytes lost */
138 #define SS_DONE 4 /* Command was sent OK */
141 * Encoding for sync transfer period.
143 #define SYNCP_MASK 0x1f
148 * Bits in flags register.
150 #define FLAGS_FIFO_LEV 0x1f
151 #define FLAGS_SEQ_STEP 0xe0
154 * Encoding for sync offset.
156 #define SYNCO_MASK 0x0f
157 #define SYNCO_ASS_CTRL 0x30 /* REQ/ACK assertion control */
158 #define SYNCO_NEG_CTRL 0xc0 /* REQ/ACK negation control */
161 * Bits in config1 register.
163 #define CF1_SLOW_CABLE 0x80 /* Slow cable mode */
164 #define CF1_NO_RES_REP 0x40 /* Disable SCSI reset reports */
165 #define CF1_PAR_TEST 0x20 /* Parity test mode enable */
166 #define CF1_PAR_ENABLE 0x10 /* Enable parity checks */
167 #define CF1_TEST 0x08 /* Chip tests */
168 #define CF1_MY_ID 0x07 /* Controller's address on bus */
171 * Encoding for clk_factor register.
174 #define CLKF_VAL(freq) ((((freq) + 4999999) / 5000000) & CLKF_MASK)
177 * Bits in test mode register.
179 #define TEST_TARGET 1 /* target test mode */
180 #define TEST_INITIATOR 2 /* initiator test mode */
181 #define TEST_TRISTATE 4 /* tristate (hi-z) test mode */
184 * Bits in config2 register.
187 #define CF2_FEATURE_EN 0x40 /* enable features / phase latch */
188 #define CF2_BYTECTRL 0x20
189 #define CF2_DREQ_HIZ 0x10
190 #define CF2_SCSI2 0x08
191 #define CF2_PAR_ABORT 0x04 /* bad parity target abort */
192 #define CF2_REG_PARERR 0x02 /* register parity error */
193 #define CF2_DMA_PARERR 0x01 /* DMA parity error */
196 * Bits in the config3 register.
198 #define CF3_ID_MSG_CHK 0x80
199 #define CF3_3B_MSGS 0x40
200 #define CF3_CDB10 0x20
201 #define CF3_FASTSCSI 0x10 /* enable fast SCSI support */
202 #define CF3_FASTCLOCK 0x08
203 #define CF3_SAVERESID 0x04
204 #define CF3_ALT_DMA 0x02
205 #define CF3_THRESH_8 0x01
208 * Bits in the config4 register.
211 #define CF4_TEST 0x02
212 #define CF4_BBTE 0x01
214 #endif /* _MAC53C94_H */
This page took 0.034405 seconds and 5 git commands to generate.