2 * zs.h: Definitions for the DECstation Z85C30 serial driver.
4 * Adapted from drivers/sbus/char/sunserial.h by Paul Mackerras.
5 * Adapted from drivers/macintosh/macserial.h by Harald Koerfgen.
7 * Copyright (C) 1996 Paul Mackerras (Paul.Mackerras@cs.anu.edu.au)
8 * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
9 * Copyright (C) 2004, 2005, 2007 Maciej W. Rozycki
16 #define ZS_NUM_REGS 16
19 * This is our internal structure for each serial port's state.
22 struct zs_scc
*scc
; /* Containing SCC. */
23 struct uart_port port
; /* Underlying UART. */
25 int clk_mode
; /* May be 1, 16, 32, or 64. */
27 unsigned int tty_break
; /* Set on BREAK condition. */
28 int tx_stopped
; /* Output is suspended. */
30 unsigned int mctrl
; /* State of modem lines. */
31 u8 brk
; /* BREAK state from RR0. */
33 u8 regs
[ZS_NUM_REGS
]; /* Channel write registers. */
37 * Per-SCC state for locking and the interrupt handler.
40 struct zs_port zport
[2];
46 #endif /* __KERNEL__ */
49 * Conversion routines to/from brg time constants from/to bits per second.
51 #define ZS_BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
52 #define ZS_BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)
55 * The Zilog register set.
58 /* Write Register 0 (Command) */
59 #define R0 0 /* Register selects */
76 #define NULLCODE 0 /* Null Code */
77 #define POINT_HIGH 0x8 /* Select upper half of registers */
78 #define RES_EXT_INT 0x10 /* Reset Ext. Status Interrupts */
79 #define SEND_ABORT 0x18 /* HDLC Abort */
80 #define RES_RxINT_FC 0x20 /* Reset RxINT on First Character */
81 #define RES_Tx_P 0x28 /* Reset TxINT Pending */
82 #define ERR_RES 0x30 /* Error Reset */
83 #define RES_H_IUS 0x38 /* Reset highest IUS */
85 #define RES_Rx_CRC 0x40 /* Reset Rx CRC Checker */
86 #define RES_Tx_CRC 0x80 /* Reset Tx CRC Checker */
87 #define RES_EOM_L 0xC0 /* Reset EOM latch */
89 /* Write Register 1 (Tx/Rx/Ext Int Enable and WAIT/DMA Commands) */
90 #define EXT_INT_ENAB 0x1 /* Ext Int Enable */
91 #define TxINT_ENAB 0x2 /* Tx Int Enable */
92 #define PAR_SPEC 0x4 /* Parity is special condition */
94 #define RxINT_DISAB 0 /* Rx Int Disable */
95 #define RxINT_FCERR 0x8 /* Rx Int on First Character Only or Error */
96 #define RxINT_ALL 0x10 /* Int on all Rx Characters or error */
97 #define RxINT_ERR 0x18 /* Int on error only */
98 #define RxINT_MASK 0x18
100 #define WT_RDY_RT 0x20 /* Wait/Ready on R/T */
101 #define WT_FN_RDYFN 0x40 /* Wait/FN/Ready FN */
102 #define WT_RDY_ENAB 0x80 /* Wait/Ready Enable */
104 /* Write Register 2 (Interrupt Vector) */
106 /* Write Register 3 (Receive Parameters and Control) */
107 #define RxENABLE 0x1 /* Rx Enable */
108 #define SYNC_L_INH 0x2 /* Sync Character Load Inhibit */
109 #define ADD_SM 0x4 /* Address Search Mode (SDLC) */
110 #define RxCRC_ENAB 0x8 /* Rx CRC Enable */
111 #define ENT_HM 0x10 /* Enter Hunt Mode */
112 #define AUTO_ENAB 0x20 /* Auto Enables */
113 #define Rx5 0x0 /* Rx 5 Bits/Character */
114 #define Rx7 0x40 /* Rx 7 Bits/Character */
115 #define Rx6 0x80 /* Rx 6 Bits/Character */
116 #define Rx8 0xc0 /* Rx 8 Bits/Character */
117 #define RxNBITS_MASK 0xc0
119 /* Write Register 4 (Transmit/Receive Miscellaneous Parameters and Modes) */
120 #define PAR_ENA 0x1 /* Parity Enable */
121 #define PAR_EVEN 0x2 /* Parity Even/Odd* */
123 #define SYNC_ENAB 0 /* Sync Modes Enable */
124 #define SB1 0x4 /* 1 stop bit/char */
125 #define SB15 0x8 /* 1.5 stop bits/char */
126 #define SB2 0xc /* 2 stop bits/char */
129 #define MONSYNC 0 /* 8 Bit Sync character */
130 #define BISYNC 0x10 /* 16 bit sync character */
131 #define SDLC 0x20 /* SDLC Mode (01111110 Sync Flag) */
132 #define EXTSYNC 0x30 /* External Sync Mode */
134 #define X1CLK 0x0 /* x1 clock mode */
135 #define X16CLK 0x40 /* x16 clock mode */
136 #define X32CLK 0x80 /* x32 clock mode */
137 #define X64CLK 0xc0 /* x64 clock mode */
138 #define XCLK_MASK 0xc0
140 /* Write Register 5 (Transmit Parameters and Controls) */
141 #define TxCRC_ENAB 0x1 /* Tx CRC Enable */
142 #define RTS 0x2 /* RTS */
143 #define SDLC_CRC 0x4 /* SDLC/CRC-16 */
144 #define TxENAB 0x8 /* Tx Enable */
145 #define SND_BRK 0x10 /* Send Break */
146 #define Tx5 0x0 /* Tx 5 bits (or less)/character */
147 #define Tx7 0x20 /* Tx 7 bits/character */
148 #define Tx6 0x40 /* Tx 6 bits/character */
149 #define Tx8 0x60 /* Tx 8 bits/character */
150 #define TxNBITS_MASK 0x60
151 #define DTR 0x80 /* DTR */
153 /* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
155 /* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
157 /* Write Register 8 (Transmit Buffer) */
159 /* Write Register 9 (Master Interrupt Control) */
160 #define VIS 1 /* Vector Includes Status */
161 #define NV 2 /* No Vector */
162 #define DLC 4 /* Disable Lower Chain */
163 #define MIE 8 /* Master Interrupt Enable */
164 #define STATHI 0x10 /* Status high */
165 #define SOFTACK 0x20 /* Software Interrupt Acknowledge */
166 #define NORESET 0 /* No reset on write to R9 */
167 #define CHRB 0x40 /* Reset channel B */
168 #define CHRA 0x80 /* Reset channel A */
169 #define FHWRES 0xc0 /* Force hardware reset */
171 /* Write Register 10 (Miscellaneous Transmitter/Receiver Control Bits) */
172 #define BIT6 1 /* 6 bit/8bit sync */
173 #define LOOPMODE 2 /* SDLC Loop mode */
174 #define ABUNDER 4 /* Abort/flag on SDLC xmit underrun */
175 #define MARKIDLE 8 /* Mark/flag on idle */
176 #define GAOP 0x10 /* Go active on poll */
177 #define NRZ 0 /* NRZ mode */
178 #define NRZI 0x20 /* NRZI mode */
179 #define FM1 0x40 /* FM1 (transition = 1) */
180 #define FM0 0x60 /* FM0 (transition = 0) */
181 #define CRCPS 0x80 /* CRC Preset I/O */
183 /* Write Register 11 (Clock Mode Control) */
184 #define TRxCXT 0 /* TRxC = Xtal output */
185 #define TRxCTC 1 /* TRxC = Transmit clock */
186 #define TRxCBR 2 /* TRxC = BR Generator Output */
187 #define TRxCDP 3 /* TRxC = DPLL output */
188 #define TRxCOI 4 /* TRxC O/I */
189 #define TCRTxCP 0 /* Transmit clock = RTxC pin */
190 #define TCTRxCP 8 /* Transmit clock = TRxC pin */
191 #define TCBR 0x10 /* Transmit clock = BR Generator output */
192 #define TCDPLL 0x18 /* Transmit clock = DPLL output */
193 #define RCRTxCP 0 /* Receive clock = RTxC pin */
194 #define RCTRxCP 0x20 /* Receive clock = TRxC pin */
195 #define RCBR 0x40 /* Receive clock = BR Generator output */
196 #define RCDPLL 0x60 /* Receive clock = DPLL output */
197 #define RTxCX 0x80 /* RTxC Xtal/No Xtal */
199 /* Write Register 12 (Lower Byte of Baud Rate Generator Time Constant) */
201 /* Write Register 13 (Upper Byte of Baud Rate Generator Time Constant) */
203 /* Write Register 14 (Miscellaneous Control Bits) */
204 #define BRENABL 1 /* Baud rate generator enable */
205 #define BRSRC 2 /* Baud rate generator source */
206 #define DTRREQ 4 /* DTR/Request function */
207 #define AUTOECHO 8 /* Auto Echo */
208 #define LOOPBAK 0x10 /* Local loopback */
209 #define SEARCH 0x20 /* Enter search mode */
210 #define RMC 0x40 /* Reset missing clock */
211 #define DISDPLL 0x60 /* Disable DPLL */
212 #define SSBR 0x80 /* Set DPLL source = BR generator */
213 #define SSRTxC 0xa0 /* Set DPLL source = RTxC */
214 #define SFMM 0xc0 /* Set FM mode */
215 #define SNRZI 0xe0 /* Set NRZI mode */
217 /* Write Register 15 (External/Status Interrupt Control) */
218 #define WR7P_EN 1 /* WR7 Prime SDLC Feature Enable */
219 #define ZCIE 2 /* Zero count IE */
220 #define DCDIE 8 /* DCD IE */
221 #define SYNCIE 0x10 /* Sync/hunt IE */
222 #define CTSIE 0x20 /* CTS IE */
223 #define TxUIE 0x40 /* Tx Underrun/EOM IE */
224 #define BRKIE 0x80 /* Break/Abort IE */
227 /* Read Register 0 (Transmit/Receive Buffer Status and External Status) */
228 #define Rx_CH_AV 0x1 /* Rx Character Available */
229 #define ZCOUNT 0x2 /* Zero count */
230 #define Tx_BUF_EMP 0x4 /* Tx Buffer empty */
231 #define DCD 0x8 /* DCD */
232 #define SYNC_HUNT 0x10 /* Sync/hunt */
233 #define CTS 0x20 /* CTS */
234 #define TxEOM 0x40 /* Tx underrun */
235 #define BRK_ABRT 0x80 /* Break/Abort */
237 /* Read Register 1 (Special Receive Condition Status) */
238 #define ALL_SNT 0x1 /* All sent */
239 /* Residue Data for 8 Rx bits/char programmed */
240 #define RES3 0x8 /* 0/3 */
241 #define RES4 0x4 /* 0/4 */
242 #define RES5 0xc /* 0/5 */
243 #define RES6 0x2 /* 0/6 */
244 #define RES7 0xa /* 0/7 */
245 #define RES8 0x6 /* 0/8 */
246 #define RES18 0xe /* 1/8 */
247 #define RES28 0x0 /* 2/8 */
248 /* Special Rx Condition Interrupts */
249 #define PAR_ERR 0x10 /* Parity Error */
250 #define Rx_OVR 0x20 /* Rx Overrun Error */
251 #define FRM_ERR 0x40 /* CRC/Framing Error */
252 #define END_FR 0x80 /* End of Frame (SDLC) */
254 /* Read Register 2 (Interrupt Vector (WR2) -- channel A). */
256 /* Read Register 2 (Modified Interrupt Vector -- channel B). */
258 /* Read Register 3 (Interrupt Pending Bits -- channel A only). */
259 #define CHBEXT 0x1 /* Channel B Ext/Stat IP */
260 #define CHBTxIP 0x2 /* Channel B Tx IP */
261 #define CHBRxIP 0x4 /* Channel B Rx IP */
262 #define CHAEXT 0x8 /* Channel A Ext/Stat IP */
263 #define CHATxIP 0x10 /* Channel A Tx IP */
264 #define CHARxIP 0x20 /* Channel A Rx IP */
266 /* Read Register 6 (SDLC FIFO Status and Byte Count LSB) */
268 /* Read Register 7 (SDLC FIFO Status and Byte Count MSB) */
270 /* Read Register 8 (Receive Data) */
272 /* Read Register 10 (Miscellaneous Status Bits) */
273 #define ONLOOP 2 /* On loop */
274 #define LOOPSEND 0x10 /* Loop sending */
275 #define CLK2MIS 0x40 /* Two clocks missing */
276 #define CLK1MIS 0x80 /* One clock missing */
278 /* Read Register 12 (Lower Byte of Baud Rate Generator Constant (WR12)) */
280 /* Read Register 13 (Upper Byte of Baud Rate Generator Constant (WR13) */
282 /* Read Register 15 (External/Status Interrupt Control (WR15)) */
284 #endif /* _SERIAL_ZS_H */
This page took 0.035206 seconds and 5 git commands to generate.