drivers/usb/phy/Kconfig

   1 #
   2 # Physical Layer USB driver configuration
   3 #
   4 menu "USB Physical Layer drivers"
   5
   6 config USB_PHY
   7         def_bool n
   8
   9 #
  10 # USB Transceiver Drivers
  11 #
  12 config AB8500_USB
  13         tristate "AB8500 USB Transceiver Driver"
  14         depends on AB8500_CORE
  15         select USB_PHY
  16         help
  17           Enable this to support the USB OTG transceiver in AB8500 chip.
  18           This transceiver supports high and full speed devices plus,
  19           in host mode, low speed.
  20
  21 config FSL_USB2_OTG
  22         bool "Freescale USB OTG Transceiver Driver"
  23         depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM && PM
  24         depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
  25         select USB_PHY
  26         help
  27           Enable this to support Freescale USB OTG transceiver.
  28
  29 config ISP1301_OMAP
  30         tristate "Philips ISP1301 with OMAP OTG"
  31         depends on I2C && ARCH_OMAP_OTG
  32         depends on USB
  33         depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
  34         select USB_PHY
  35         help
  36           If you say yes here you get support for the Philips ISP1301
  37           USB-On-The-Go transceiver working with the OMAP OTG controller.
  38           The ISP1301 is a full speed USB  transceiver which is used in
  39           products including H2, H3, and H4 development boards for Texas
  40           Instruments OMAP processors.
  41
  42           This driver can also be built as a module.  If so, the module
  43           will be called phy-isp1301-omap.
  44
  45 config KEYSTONE_USB_PHY
  46         tristate "Keystone USB PHY Driver"
  47         depends on ARCH_KEYSTONE || COMPILE_TEST
  48         depends on NOP_USB_XCEIV
  49         help
  50           Enable this to support Keystone USB phy. This driver provides
  51           interface to interact with USB 2.0 and USB 3.0 PHY that is part
  52           of the Keystone SOC.
  53
  54 config NOP_USB_XCEIV
  55         tristate "NOP USB Transceiver Driver"
  56         depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, NOP can't be built-in
  57         select USB_PHY
  58         help
  59           This driver is to be used by all the usb transceiver which are either
  60           built-in with usb ip or which are autonomous and doesn't require any
  61           phy programming such as ISP1x04 etc.
  62
  63 config AM335X_CONTROL_USB
  64         tristate
  65
  66 config AM335X_PHY_USB
  67         tristate "AM335x USB PHY Driver"
  68         depends on ARM || COMPILE_TEST
  69         depends on NOP_USB_XCEIV
  70         select USB_PHY
  71         select AM335X_CONTROL_USB
  72         select USB_COMMON
  73         help
  74           This driver provides PHY support for that phy which part for the
  75           AM335x SoC.
  76
  77 config SAMSUNG_USBPHY
  78         tristate
  79         help
  80           Enable this to support Samsung USB phy helper driver for Samsung SoCs.
  81           This driver provides common interface to interact, for Samsung USB 2.0 PHY
  82           driver and later for Samsung USB 3.0 PHY driver.
  83
  84 config TWL6030_USB
  85         tristate "TWL6030 USB Transceiver Driver"
  86         depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
  87         help
  88           Enable this to support the USB OTG transceiver on TWL6030
  89           family chips. This TWL6030 transceiver has the VBUS and ID GND
  90           and OTG SRP events capabilities. For all other transceiver functionality
  91           UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs
  92           are hooked to this driver through platform_data structure.
  93           The definition of internal PHY APIs are in the mach-omap2 layer.
  94
  95 config USB_GPIO_VBUS
  96         tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
  97         depends on GPIOLIB || COMPILE_TEST
  98         depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
  99         select USB_PHY
 100         help
 101           Provides simple GPIO VBUS sensing for controllers with an
 102           internal transceiver via the usb_phy interface, and
 103           optionally control of a D+ pullup GPIO as well as a VBUS
 104           current limit regulator.
 105
 106 config OMAP_OTG
 107         tristate "OMAP USB OTG controller driver"
 108         depends on ARCH_OMAP_OTG && EXTCON
 109         help
 110           Enable this to support some transceivers on OMAP1 platforms. OTG
 111           controller is needed to switch between host and peripheral modes.
 112
 113           This driver can also be built as a module. If so, the module
 114           will be called phy-omap-otg.
 115
 116 config TAHVO_USB
 117         tristate "Tahvo USB transceiver driver"
 118         depends on MFD_RETU && EXTCON
 119         depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
 120         select USB_PHY
 121         help
 122           Enable this to support USB transceiver on Tahvo. This is used
 123           at least on Nokia 770.
 124
 125 config TAHVO_USB_HOST_BY_DEFAULT
 126         depends on TAHVO_USB
 127         bool "Device in USB host mode by default"
 128         help
 129           Say Y here, if you want the device to enter USB host mode
 130           by default on bootup.
 131
 132 config USB_ISP1301
 133         tristate "NXP ISP1301 USB transceiver support"
 134         depends on USB || USB_GADGET
 135         depends on I2C
 136         select USB_PHY
 137         help
 138           Say Y here to add support for the NXP ISP1301 USB transceiver driver.
 139           This chip is typically used as USB transceiver for USB host, gadget
 140           and OTG drivers (to be selected separately).
 141
 142           To compile this driver as a module, choose M here: the
 143           module will be called phy-isp1301.
 144
 145 config USB_MSM_OTG
 146         tristate "Qualcomm on-chip USB OTG controller support"
 147         depends on (USB || USB_GADGET) && (ARCH_QCOM || COMPILE_TEST)
 148         depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
 149         depends on RESET_CONTROLLER
 150         depends on EXTCON
 151         select USB_PHY
 152         help
 153           Enable this to support the USB OTG transceiver on Qualcomm chips. It
 154           handles PHY initialization, clock management, and workarounds
 155           required after resetting the hardware and power management.
 156           This driver is required even for peripheral only or host only
 157           mode configurations.
 158           This driver is not supported on boards like trout which
 159           has an external PHY.
 160
 161 config USB_QCOM_8X16_PHY
 162         tristate "Qualcomm APQ8016/MSM8916 on-chip USB PHY controller support"
 163         depends on ARCH_QCOM || COMPILE_TEST
 164         depends on RESET_CONTROLLER && EXTCON
 165         select USB_PHY
 166         select USB_ULPI_VIEWPORT
 167         help
 168           Enable this to support the USB transceiver on Qualcomm 8x16 chipsets.
 169           It handles PHY initialization, clock management, power management,
 170           and workarounds required after resetting the hardware.
 171
 172           To compile this driver as a module, choose M here: the
 173           module will be called phy-qcom-8x16-usb.
 174
 175 config USB_MV_OTG
 176         tristate "Marvell USB OTG support"
 177         depends on USB_EHCI_MV && USB_MV_UDC && PM && USB_OTG
 178         depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
 179         select USB_PHY
 180         help
 181           Say Y here if you want to build Marvell USB OTG transciever
 182           driver in kernel (including PXA and MMP series). This driver
 183           implements role switch between EHCI host driver and gadget driver.
 184
 185           To compile this driver as a module, choose M here.
 186
 187 config USB_MXS_PHY
 188         tristate "Freescale MXS USB PHY support"
 189         depends on ARCH_MXC || ARCH_MXS
 190         select STMP_DEVICE
 191         select USB_PHY
 192         help
 193           Enable this to support the Freescale MXS USB PHY.
 194
 195           MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
 196
 197 config USB_ULPI
 198         bool "Generic ULPI Transceiver Driver"
 199         depends on ARM || ARM64
 200         select USB_ULPI_VIEWPORT
 201         help
 202           Enable this to support ULPI connected USB OTG transceivers which
 203           are likely found on embedded boards.
 204
 205 config USB_ULPI_VIEWPORT
 206         bool
 207         help
 208           Provides read/write operations to the ULPI phy register set for
 209           controllers with a viewport register (e.g. Chipidea/ARC controllers).
 210
 211 endmenu