drivers/usb/phy/Kconfig

   1 #
   2 # Physical Layer USB driver configuration
   3 #
   4 menu "USB Physical Layer drivers"
   5
   6 config USB_PHY
   7         def_bool n
   8
   9 #
  10 # USB Transceiver Drivers
  11 #
  12 config AB8500_USB
  13         tristate "AB8500 USB Transceiver Driver"
  14         depends on AB8500_CORE
  15         select USB_PHY
  16         help
  17           Enable this to support the USB OTG transceiver in AB8500 chip.
  18           This transceiver supports high and full speed devices plus,
  19           in host mode, low speed.
  20
  21 config FSL_USB2_OTG
  22         bool "Freescale USB OTG Transceiver Driver"
  23         depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM && PM
  24         select USB_PHY
  25         help
  26           Enable this to support Freescale USB OTG transceiver.
  27
  28 config ISP1301_OMAP
  29         tristate "Philips ISP1301 with OMAP OTG"
  30         depends on I2C && ARCH_OMAP_OTG
  31         depends on USB
  32         select USB_PHY
  33         help
  34           If you say yes here you get support for the Philips ISP1301
  35           USB-On-The-Go transceiver working with the OMAP OTG controller.
  36           The ISP1301 is a full speed USB  transceiver which is used in
  37           products including H2, H3, and H4 development boards for Texas
  38           Instruments OMAP processors.
  39
  40           This driver can also be built as a module.  If so, the module
  41           will be called phy-isp1301-omap.
  42
  43 config KEYSTONE_USB_PHY
  44         tristate "Keystone USB PHY Driver"
  45         depends on ARCH_KEYSTONE || COMPILE_TEST
  46         select NOP_USB_XCEIV
  47         help
  48           Enable this to support Keystone USB phy. This driver provides
  49           interface to interact with USB 2.0 and USB 3.0 PHY that is part
  50           of the Keystone SOC.
  51
  52 config NOP_USB_XCEIV
  53         tristate "NOP USB Transceiver Driver"
  54         select USB_PHY
  55         help
  56           This driver is to be used by all the usb transceiver which are either
  57           built-in with usb ip or which are autonomous and doesn't require any
  58           phy programming such as ISP1x04 etc.
  59
  60 config AM335X_CONTROL_USB
  61         tristate
  62
  63 config AM335X_PHY_USB
  64         tristate "AM335x USB PHY Driver"
  65         depends on ARM || COMPILE_TEST
  66         select USB_PHY
  67         select AM335X_CONTROL_USB
  68         select NOP_USB_XCEIV
  69         select USB_COMMON
  70         help
  71           This driver provides PHY support for that phy which part for the
  72           AM335x SoC.
  73
  74 config SAMSUNG_USBPHY
  75         tristate
  76         help
  77           Enable this to support Samsung USB phy helper driver for Samsung SoCs.
  78           This driver provides common interface to interact, for Samsung USB 2.0 PHY
  79           driver and later for Samsung USB 3.0 PHY driver.
  80
  81 config TWL6030_USB
  82         tristate "TWL6030 USB Transceiver Driver"
  83         depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS
  84         help
  85           Enable this to support the USB OTG transceiver on TWL6030
  86           family chips. This TWL6030 transceiver has the VBUS and ID GND
  87           and OTG SRP events capabilities. For all other transceiver functionality
  88           UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs
  89           are hooked to this driver through platform_data structure.
  90           The definition of internal PHY APIs are in the mach-omap2 layer.
  91
  92 config USB_GPIO_VBUS
  93         tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
  94         depends on GPIOLIB || COMPILE_TEST
  95         select USB_PHY
  96         help
  97           Provides simple GPIO VBUS sensing for controllers with an
  98           internal transceiver via the usb_phy interface, and
  99           optionally control of a D+ pullup GPIO as well as a VBUS
 100           current limit regulator.
 101
 102 config OMAP_OTG
 103         tristate "OMAP USB OTG controller driver"
 104         depends on ARCH_OMAP_OTG && EXTCON
 105         help
 106           Enable this to support some transceivers on OMAP1 platforms. OTG
 107           controller is needed to switch between host and peripheral modes.
 108
 109           This driver can also be built as a module. If so, the module
 110           will be called phy-omap-otg.
 111
 112 config TAHVO_USB
 113         tristate "Tahvo USB transceiver driver"
 114         depends on MFD_RETU && EXTCON
 115         select USB_PHY
 116         help
 117           Enable this to support USB transceiver on Tahvo. This is used
 118           at least on Nokia 770.
 119
 120 config TAHVO_USB_HOST_BY_DEFAULT
 121         depends on TAHVO_USB
 122         bool "Device in USB host mode by default"
 123         help
 124           Say Y here, if you want the device to enter USB host mode
 125           by default on bootup.
 126
 127 config USB_ISP1301
 128         tristate "NXP ISP1301 USB transceiver support"
 129         depends on USB || USB_GADGET
 130         depends on I2C
 131         select USB_PHY
 132         help
 133           Say Y here to add support for the NXP ISP1301 USB transceiver driver.
 134           This chip is typically used as USB transceiver for USB host, gadget
 135           and OTG drivers (to be selected separately).
 136
 137           To compile this driver as a module, choose M here: the
 138           module will be called phy-isp1301.
 139
 140 config USB_MSM_OTG
 141         tristate "Qualcomm on-chip USB OTG controller support"
 142         depends on (USB || USB_GADGET) && (ARCH_QCOM || COMPILE_TEST)
 143         depends on RESET_CONTROLLER
 144         depends on EXTCON
 145         select USB_PHY
 146         help
 147           Enable this to support the USB OTG transceiver on Qualcomm chips. It
 148           handles PHY initialization, clock management, and workarounds
 149           required after resetting the hardware and power management.
 150           This driver is required even for peripheral only or host only
 151           mode configurations.
 152           This driver is not supported on boards like trout which
 153           has an external PHY.
 154
 155 config USB_QCOM_8X16_PHY
 156         tristate "Qualcomm APQ8016/MSM8916 on-chip USB PHY controller support"
 157         depends on ARCH_QCOM || COMPILE_TEST
 158         depends on RESET_CONTROLLER && EXTCON
 159         select USB_PHY
 160         select USB_ULPI_VIEWPORT
 161         help
 162           Enable this to support the USB transceiver on Qualcomm 8x16 chipsets.
 163           It handles PHY initialization, clock management, power management,
 164           and workarounds required after resetting the hardware.
 165
 166           To compile this driver as a module, choose M here: the
 167           module will be called phy-qcom-8x16-usb.
 168
 169 config USB_MV_OTG
 170         tristate "Marvell USB OTG support"
 171         depends on USB_EHCI_MV && USB_MV_UDC && PM && USB_OTG
 172         select USB_PHY
 173         help
 174           Say Y here if you want to build Marvell USB OTG transciever
 175           driver in kernel (including PXA and MMP series). This driver
 176           implements role switch between EHCI host driver and gadget driver.
 177
 178           To compile this driver as a module, choose M here.
 179
 180 config USB_MXS_PHY
 181         tristate "Freescale MXS USB PHY support"
 182         depends on ARCH_MXC || ARCH_MXS
 183         select STMP_DEVICE
 184         select USB_PHY
 185         help
 186           Enable this to support the Freescale MXS USB PHY.
 187
 188           MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x.
 189
 190 config USB_ULPI
 191         bool "Generic ULPI Transceiver Driver"
 192         depends on ARM || ARM64
 193         select USB_ULPI_VIEWPORT
 194         help
 195           Enable this to support ULPI connected USB OTG transceivers which
 196           are likely found on embedded boards.
 197
 198 config USB_ULPI_VIEWPORT
 199         bool
 200         help
 201           Provides read/write operations to the ULPI phy register set for
 202           controllers with a viewport register (e.g. Chipidea/ARC controllers).
 203
 204 endmenu