drivers/video/Kconfig

   1 #
   2 # Video configuration
   3 #
   4
   5 menu "Graphics support"
   6         depends on HAS_IOMEM
   7
   8 config HAVE_FB_ATMEL
   9         bool
  10
  11 config HAVE_FB_IMX
  12         bool
  13
  14 source "drivers/char/agp/Kconfig"
  15
  16 source "drivers/gpu/vga/Kconfig"
  17
  18 source "drivers/gpu/drm/Kconfig"
  19
  20 source "drivers/gpu/stub/Kconfig"
  21
  22 config VGASTATE
  23        tristate
  24        default n
  25
  26 config VIDEO_OUTPUT_CONTROL
  27         tristate "Lowlevel video output switch controls"
  28         help
  29           This framework adds support for low-level control of the video
  30           output switch.
  31
  32 menuconfig FB
  33         tristate "Support for frame buffer devices"
  34         ---help---
  35           The frame buffer device provides an abstraction for the graphics
  36           hardware. It represents the frame buffer of some video hardware and
  37           allows application software to access the graphics hardware through
  38           a well-defined interface, so the software doesn't need to know
  39           anything about the low-level (hardware register) stuff.
  40
  41           Frame buffer devices work identically across the different
  42           architectures supported by Linux and make the implementation of
  43           application programs easier and more portable; at this point, an X
  44           server exists which uses the frame buffer device exclusively.
  45           On several non-X86 architectures, the frame buffer device is the
  46           only way to use the graphics hardware.
  47
  48           The device is accessed through special device nodes, usually located
  49           in the /dev directory, i.e. /dev/fb*.
  50
  51           You need an utility program called fbset to make full use of frame
  52           buffer devices. Please read <file:Documentation/fb/framebuffer.txt>
  53           and the Framebuffer-HOWTO at
  54           <http://www.munted.org.uk/programming/Framebuffer-HOWTO-1.3.html> for more
  55           information.
  56
  57           Say Y here and to the driver for your graphics board below if you
  58           are compiling a kernel for a non-x86 architecture.
  59
  60           If you are compiling for the x86 architecture, you can say Y if you
  61           want to play with it, but it is not essential. Please note that
  62           running graphical applications that directly touch the hardware
  63           (e.g. an accelerated X server) and that are not frame buffer
  64           device-aware may cause unexpected results. If unsure, say N.
  65
  66 config FIRMWARE_EDID
  67        bool "Enable firmware EDID"
  68        depends on FB
  69        default n
  70        ---help---
  71          This enables access to the EDID transferred from the firmware.
  72          On the i386, this is from the Video BIOS. Enable this if DDC/I2C
  73          transfers do not work for your driver and if you are using
  74          nvidiafb, i810fb or savagefb.
  75
  76          In general, choosing Y for this option is safe.  If you
  77          experience extremely long delays while booting before you get
  78          something on your display, try setting this to N.  Matrox cards in
  79          combination with certain motherboards and monitors are known to
  80          suffer from this problem.
  81
  82 config FB_DDC
  83        tristate
  84        depends on FB
  85        select I2C_ALGOBIT
  86        select I2C
  87        default n
  88
  89 config FB_BOOT_VESA_SUPPORT
  90         bool
  91         depends on FB
  92         default n
  93         ---help---
  94           If true, at least one selected framebuffer driver can take advantage
  95           of VESA video modes set at an early boot stage via the vga= parameter.
  96
  97 config FB_CFB_FILLRECT
  98         tristate
  99         depends on FB
 100         default n
 101         ---help---
 102           Include the cfb_fillrect function for generic software rectangle
 103           filling. This is used by drivers that don't provide their own
 104           (accelerated) version.
 105
 106 config FB_CFB_COPYAREA
 107         tristate
 108         depends on FB
 109         default n
 110         ---help---
 111           Include the cfb_copyarea function for generic software area copying.
 112           This is used by drivers that don't provide their own (accelerated)
 113           version.
 114
 115 config FB_CFB_IMAGEBLIT
 116         tristate
 117         depends on FB
 118         default n
 119         ---help---
 120           Include the cfb_imageblit function for generic software image
 121           blitting. This is used by drivers that don't provide their own
 122           (accelerated) version.
 123
 124 config FB_CFB_REV_PIXELS_IN_BYTE
 125         bool
 126         depends on FB
 127         default n
 128         ---help---
 129           Allow generic frame-buffer functions to work on displays with 1, 2
 130           and 4 bits per pixel depths which has opposite order of pixels in
 131           byte order to bytes in long order.
 132
 133 config FB_SYS_FILLRECT
 134         tristate
 135         depends on FB
 136         default n
 137         ---help---
 138           Include the sys_fillrect function for generic software rectangle
 139           filling. This is used by drivers that don't provide their own
 140           (accelerated) version and the framebuffer is in system RAM.
 141
 142 config FB_SYS_COPYAREA
 143         tristate
 144         depends on FB
 145         default n
 146         ---help---
 147           Include the sys_copyarea function for generic software area copying.
 148           This is used by drivers that don't provide their own (accelerated)
 149           version and the framebuffer is in system RAM.
 150
 151 config FB_SYS_IMAGEBLIT
 152         tristate
 153         depends on FB
 154         default n
 155         ---help---
 156           Include the sys_imageblit function for generic software image
 157           blitting. This is used by drivers that don't provide their own
 158           (accelerated) version and the framebuffer is in system RAM.
 159
 160 menuconfig FB_FOREIGN_ENDIAN
 161         bool "Framebuffer foreign endianness support"
 162         depends on FB
 163         ---help---
 164           This menu will let you enable support for the framebuffers with
 165           non-native endianness (e.g. Little-Endian framebuffer on a
 166           Big-Endian machine). Most probably you don't have such hardware,
 167           so it's safe to say "n" here.
 168
 169 choice
 170         prompt "Choice endianness support"
 171         depends on FB_FOREIGN_ENDIAN
 172
 173 config FB_BOTH_ENDIAN
 174         bool "Support for Big- and Little-Endian framebuffers"
 175
 176 config FB_BIG_ENDIAN
 177         bool "Support for Big-Endian framebuffers only"
 178
 179 config FB_LITTLE_ENDIAN
 180         bool "Support for Little-Endian framebuffers only"
 181
 182 endchoice
 183
 184 config FB_SYS_FOPS
 185        tristate
 186        depends on FB
 187        default n
 188
 189 config FB_DEFERRED_IO
 190         bool
 191         depends on FB
 192
 193 config FB_HECUBA
 194         tristate
 195         depends on FB
 196         depends on FB_DEFERRED_IO
 197
 198 config FB_SVGALIB
 199         tristate
 200         depends on FB
 201         default n
 202         ---help---
 203           Common utility functions useful to fbdev drivers of VGA-based
 204           cards.
 205
 206 config FB_MACMODES
 207        tristate
 208        depends on FB
 209        default n
 210
 211 config FB_BACKLIGHT
 212         bool
 213         depends on FB
 214         select BACKLIGHT_LCD_SUPPORT
 215         select BACKLIGHT_CLASS_DEVICE
 216         default n
 217
 218 config FB_MODE_HELPERS
 219         bool "Enable Video Mode Handling Helpers"
 220         depends on FB
 221         default n
 222         ---help---
 223           This enables functions for handling video modes using the
 224           Generalized Timing Formula and the EDID parser. A few drivers rely
 225           on this feature such as the radeonfb, rivafb, and the i810fb. If
 226           your driver does not take advantage of this feature, choosing Y will
 227           just increase the kernel size by about 5K.
 228
 229 config FB_TILEBLITTING
 230        bool "Enable Tile Blitting Support"
 231        depends on FB
 232        default n
 233        ---help---
 234          This enables tile blitting.  Tile blitting is a drawing technique
 235          where the screen is divided into rectangular sections (tiles), whereas
 236          the standard blitting divides the screen into pixels. Because the
 237          default drawing element is a tile, drawing functions will be passed
 238          parameters in terms of number of tiles instead of number of pixels.
 239          For example, to draw a single character, instead of using bitmaps,
 240          an index to an array of bitmaps will be used.  To clear or move a
 241          rectangular section of a screen, the rectangle will be described in
 242          terms of number of tiles in the x- and y-axis.
 243
 244          This is particularly important to one driver, matroxfb.  If
 245          unsure, say N.
 246
 247 comment "Frame buffer hardware drivers"
 248         depends on FB
 249
 250 config FB_CIRRUS
 251         tristate "Cirrus Logic support"
 252         depends on FB && (ZORRO || PCI)
 253         select FB_CFB_FILLRECT
 254         select FB_CFB_COPYAREA
 255         select FB_CFB_IMAGEBLIT
 256         ---help---
 257           This enables support for Cirrus Logic GD542x/543x based boards on
 258           Amiga: SD64, Piccolo, Picasso II/II+, Picasso IV, or EGS Spectrum.
 259
 260           If you have a PCI-based system, this enables support for these
 261           chips: GD-543x, GD-544x, GD-5480.
 262
 263           Please read the file <file:Documentation/fb/cirrusfb.txt>.
 264
 265           Say N unless you have such a graphics board or plan to get one
 266           before you next recompile the kernel.
 267
 268 config FB_PM2
 269         tristate "Permedia2 support"
 270         depends on FB && ((AMIGA && BROKEN) || PCI)
 271         select FB_CFB_FILLRECT
 272         select FB_CFB_COPYAREA
 273         select FB_CFB_IMAGEBLIT
 274         help
 275           This is the frame buffer device driver for cards based on
 276           the 3D Labs Permedia, Permedia 2 and Permedia 2V chips.
 277           The driver was tested on the following cards:
 278                 Diamond FireGL 1000 PRO AGP
 279                 ELSA Gloria Synergy PCI
 280                 Appian Jeronimo PRO (both heads) PCI
 281                 3DLabs Oxygen ACX aka EONtronics Picasso P2 PCI
 282                 Techsource Raptor GFX-8P (aka Sun PGX-32) on SPARC
 283                 ASK Graphic Blaster Exxtreme AGP
 284
 285           To compile this driver as a module, choose M here: the
 286           module will be called pm2fb.
 287
 288 config FB_PM2_FIFO_DISCONNECT
 289         bool "enable FIFO disconnect feature"
 290         depends on FB_PM2 && PCI
 291         help
 292           Support the Permedia2 FIFO disconnect feature.
 293
 294 config FB_ARMCLCD
 295         tristate "ARM PrimeCell PL110 support"
 296         depends on FB && ARM && ARM_AMBA
 297         select FB_CFB_FILLRECT
 298         select FB_CFB_COPYAREA
 299         select FB_CFB_IMAGEBLIT
 300         help
 301           This framebuffer device driver is for the ARM PrimeCell PL110
 302           Colour LCD controller.  ARM PrimeCells provide the building
 303           blocks for System on a Chip devices.
 304
 305           If you want to compile this as a module (=code which can be
 306           inserted into and removed from the running kernel), say M
 307           here and read <file:Documentation/kbuild/modules.txt>.  The module
 308           will be called amba-clcd.
 309
 310 choice
 311
 312         depends on FB_ARMCLCD && (ARCH_LH7A40X || ARCH_LH7952X)
 313         prompt "LCD Panel"
 314         default FB_ARMCLCD_SHARP_LQ035Q7DB02
 315
 316 config FB_ARMCLCD_SHARP_LQ035Q7DB02_HRTFT
 317         bool "LogicPD LCD 3.5\" QVGA w/HRTFT IC"
 318         help
 319           This is an implementation of the Sharp LQ035Q7DB02, a 3.5"
 320           color QVGA, HRTFT panel.  The LogicPD device includes
 321           an integrated HRTFT controller IC.
 322           The native resolution is 240x320.
 323
 324 config FB_ARMCLCD_SHARP_LQ057Q3DC02
 325         bool "LogicPD LCD 5.7\" QVGA"
 326         help
 327           This is an implementation of the Sharp LQ057Q3DC02, a 5.7"
 328           color QVGA, TFT panel.  The LogicPD device includes an
 329           The native resolution is 320x240.
 330
 331 config FB_ARMCLCD_SHARP_LQ64D343
 332         bool "LogicPD LCD 6.4\" VGA"
 333         help
 334           This is an implementation of the Sharp LQ64D343, a 6.4"
 335           color VGA, TFT panel.  The LogicPD device includes an
 336           The native resolution is 640x480.
 337
 338 config FB_ARMCLCD_SHARP_LQ10D368
 339         bool "LogicPD LCD 10.4\" VGA"
 340         help
 341           This is an implementation of the Sharp LQ10D368, a 10.4"
 342           color VGA, TFT panel.  The LogicPD device includes an
 343           The native resolution is 640x480.
 344
 345
 346 config FB_ARMCLCD_SHARP_LQ121S1DG41
 347         bool "LogicPD LCD 12.1\" SVGA"
 348         help
 349           This is an implementation of the Sharp LQ121S1DG41, a 12.1"
 350           color SVGA, TFT panel.  The LogicPD device includes an
 351           The native resolution is 800x600.
 352
 353           This panel requires a clock rate may be an integer fraction
 354           of the base LCDCLK frequency.  The driver will select the
 355           highest frequency available that is lower than the maximum
 356           allowed.  The panel may flicker if the clock rate is
 357           slower than the recommended minimum.
 358
 359 config FB_ARMCLCD_AUO_A070VW01_WIDE
 360         bool "AU Optronics A070VW01 LCD 7.0\" WIDE"
 361         help
 362           This is an implementation of the AU Optronics, a 7.0"
 363           WIDE Color.  The native resolution is 234x480.
 364
 365 config FB_ARMCLCD_HITACHI
 366         bool "Hitachi Wide Screen 800x480"
 367         help
 368           This is an implementation of the Hitachi 800x480.
 369
 370 endchoice
 371
 372
 373 config FB_ACORN
 374         bool "Acorn VIDC support"
 375         depends on (FB = y) && ARM && ARCH_ACORN
 376         select FB_CFB_FILLRECT
 377         select FB_CFB_COPYAREA
 378         select FB_CFB_IMAGEBLIT
 379         help
 380           This is the frame buffer device driver for the Acorn VIDC graphics
 381           hardware found in Acorn RISC PCs and other ARM-based machines.  If
 382           unsure, say N.
 383
 384 config FB_CLPS711X
 385         bool "CLPS711X LCD support"
 386         depends on (FB = y) && ARM && ARCH_CLPS711X
 387         select FB_CFB_FILLRECT
 388         select FB_CFB_COPYAREA
 389         select FB_CFB_IMAGEBLIT
 390         help
 391           Say Y to enable the Framebuffer driver for the CLPS7111 and
 392           EP7212 processors.
 393
 394 config FB_SA1100
 395         bool "SA-1100 LCD support"
 396         depends on (FB = y) && ARM && ARCH_SA1100
 397         select FB_CFB_FILLRECT
 398         select FB_CFB_COPYAREA
 399         select FB_CFB_IMAGEBLIT
 400         help
 401           This is a framebuffer device for the SA-1100 LCD Controller.
 402           See <http://www.linux-fbdev.org/> for information on framebuffer
 403           devices.
 404
 405           If you plan to use the LCD display with your SA-1100 system, say
 406           Y here.
 407
 408 config FB_IMX
 409         tristate "Motorola i.MX LCD support"
 410         depends on FB && (HAVE_FB_IMX || ARCH_MX1 || ARCH_MX2)
 411         select FB_CFB_FILLRECT
 412         select FB_CFB_COPYAREA
 413         select FB_CFB_IMAGEBLIT
 414
 415 config FB_CYBER2000
 416         tristate "CyberPro 2000/2010/5000 support"
 417         depends on FB && PCI && (BROKEN || !SPARC64)
 418         select FB_CFB_FILLRECT
 419         select FB_CFB_COPYAREA
 420         select FB_CFB_IMAGEBLIT
 421         help
 422           This enables support for the Integraphics CyberPro 20x0 and 5000
 423           VGA chips used in the Rebel.com Netwinder and other machines.
 424           Say Y if you have a NetWinder or a graphics card containing this
 425           device, otherwise say N.
 426
 427 config FB_APOLLO
 428         bool
 429         depends on (FB = y) && APOLLO
 430         default y
 431         select FB_CFB_FILLRECT
 432         select FB_CFB_IMAGEBLIT
 433
 434 config FB_Q40
 435         bool
 436         depends on (FB = y) && Q40
 437         default y
 438         select FB_CFB_FILLRECT
 439         select FB_CFB_COPYAREA
 440         select FB_CFB_IMAGEBLIT
 441
 442 config FB_AMIGA
 443         tristate "Amiga native chipset support"
 444         depends on FB && AMIGA
 445         help
 446           This is the frame buffer device driver for the builtin graphics
 447           chipset found in Amigas.
 448
 449           To compile this driver as a module, choose M here: the
 450           module will be called amifb.
 451
 452 config FB_AMIGA_OCS
 453         bool "Amiga OCS chipset support"
 454         depends on FB_AMIGA
 455         help
 456           This enables support for the original Agnus and Denise video chips,
 457           found in the Amiga 1000 and most A500's and A2000's. If you intend
 458           to run Linux on any of these systems, say Y; otherwise say N.
 459
 460 config FB_AMIGA_ECS
 461         bool "Amiga ECS chipset support"
 462         depends on FB_AMIGA
 463         help
 464           This enables support for the Enhanced Chip Set, found in later
 465           A500's, later A2000's, the A600, the A3000, the A3000T and CDTV. If
 466           you intend to run Linux on any of these systems, say Y; otherwise
 467           say N.
 468
 469 config FB_AMIGA_AGA
 470         bool "Amiga AGA chipset support"
 471         depends on FB_AMIGA
 472         help
 473           This enables support for the Advanced Graphics Architecture (also
 474           known as the AGA or AA) Chip Set, found in the A1200, A4000, A4000T
 475           and CD32. If you intend to run Linux on any of these systems, say Y;
 476           otherwise say N.
 477
 478 config FB_FM2
 479         bool "Amiga FrameMaster II/Rainbow II support"
 480         depends on (FB = y) && ZORRO
 481         select FB_CFB_FILLRECT
 482         select FB_CFB_COPYAREA
 483         select FB_CFB_IMAGEBLIT
 484         help
 485           This is the frame buffer device driver for the Amiga FrameMaster
 486           card from BSC (exhibited 1992 but not shipped as a CBM product).
 487
 488 config FB_ARC
 489         tristate "Arc Monochrome LCD board support"
 490         depends on FB && X86
 491         select FB_SYS_FILLRECT
 492         select FB_SYS_COPYAREA
 493         select FB_SYS_IMAGEBLIT
 494         select FB_SYS_FOPS
 495         help
 496           This enables support for the Arc Monochrome LCD board. The board
 497           is based on the KS-108 lcd controller and is typically a matrix
 498           of 2*n chips. This driver was tested with a 128x64 panel. This
 499           driver supports it for use with x86 SBCs through a 16 bit GPIO
 500           interface (8 bit data, 8 bit control). If you anticipate using
 501           this driver, say Y or M; otherwise say N. You must specify the
 502           GPIO IO address to be used for setting control and data.
 503
 504 config FB_ATARI
 505         bool "Atari native chipset support"
 506         depends on (FB = y) && ATARI
 507         select FB_CFB_FILLRECT
 508         select FB_CFB_COPYAREA
 509         select FB_CFB_IMAGEBLIT
 510         help
 511           This is the frame buffer device driver for the builtin graphics
 512           chipset found in Ataris.
 513
 514 config FB_OF
 515         bool "Open Firmware frame buffer device support"
 516         depends on (FB = y) && (PPC64 || PPC_OF) && (!PPC_PSERIES || PCI)
 517         select FB_CFB_FILLRECT
 518         select FB_CFB_COPYAREA
 519         select FB_CFB_IMAGEBLIT
 520         select FB_MACMODES
 521         help
 522           Say Y if you want support with Open Firmware for your graphics
 523           board.
 524
 525 config FB_CONTROL
 526         bool "Apple \"control\" display support"
 527         depends on (FB = y) && PPC_PMAC && PPC32
 528         select FB_CFB_FILLRECT
 529         select FB_CFB_COPYAREA
 530         select FB_CFB_IMAGEBLIT
 531         select FB_MACMODES
 532         help
 533           This driver supports a frame buffer for the graphics adapter in the
 534           Power Macintosh 7300 and others.
 535
 536 config FB_PLATINUM
 537         bool "Apple \"platinum\" display support"
 538         depends on (FB = y) && PPC_PMAC && PPC32
 539         select FB_CFB_FILLRECT
 540         select FB_CFB_COPYAREA
 541         select FB_CFB_IMAGEBLIT
 542         select FB_MACMODES
 543         help
 544           This driver supports a frame buffer for the "platinum" graphics
 545           adapter in some Power Macintoshes.
 546
 547 config FB_VALKYRIE
 548         bool "Apple \"valkyrie\" display support"
 549         depends on (FB = y) && (MAC || (PPC_PMAC && PPC32))
 550         select FB_CFB_FILLRECT
 551         select FB_CFB_COPYAREA
 552         select FB_CFB_IMAGEBLIT
 553         select FB_MACMODES
 554         help
 555           This driver supports a frame buffer for the "valkyrie" graphics
 556           adapter in some Power Macintoshes.
 557
 558 config FB_CT65550
 559         bool "Chips 65550 display support"
 560         depends on (FB = y) && PPC32 && PCI
 561         select FB_CFB_FILLRECT
 562         select FB_CFB_COPYAREA
 563         select FB_CFB_IMAGEBLIT
 564         help
 565           This is the frame buffer device driver for the Chips & Technologies
 566           65550 graphics chip in PowerBooks.
 567
 568 config FB_ASILIANT
 569         bool "Asiliant (Chips) 69000 display support"
 570         depends on (FB = y) && PCI
 571         select FB_CFB_FILLRECT
 572         select FB_CFB_COPYAREA
 573         select FB_CFB_IMAGEBLIT
 574         help
 575           This is the frame buffer device driver for the Asiliant 69030 chipset
 576
 577 config FB_IMSTT
 578         bool "IMS Twin Turbo display support"
 579         depends on (FB = y) && PCI
 580         select FB_CFB_IMAGEBLIT
 581         select FB_MACMODES if PPC
 582         help
 583           The IMS Twin Turbo is a PCI-based frame buffer card bundled with
 584           many Macintosh and compatible computers.
 585
 586 config FB_VGA16
 587         tristate "VGA 16-color graphics support"
 588         depends on FB && (X86 || PPC)
 589         select FB_CFB_FILLRECT
 590         select FB_CFB_COPYAREA
 591         select FB_CFB_IMAGEBLIT
 592         select VGASTATE
 593         select FONT_8x16 if FRAMEBUFFER_CONSOLE
 594         help
 595           This is the frame buffer device driver for VGA 16 color graphic
 596           cards. Say Y if you have such a card.
 597
 598           To compile this driver as a module, choose M here: the
 599           module will be called vga16fb.
 600
 601 config FB_BF54X_LQ043
 602         tristate "SHARP LQ043 TFT LCD (BF548 EZKIT)"
 603         depends on FB && (BF54x) && !BF542
 604         select FB_CFB_FILLRECT
 605         select FB_CFB_COPYAREA
 606         select FB_CFB_IMAGEBLIT
 607         help
 608          This is the framebuffer device driver for a SHARP LQ043T1DG01 TFT LCD
 609
 610 config FB_BFIN_T350MCQB
 611         tristate "Varitronix COG-T350MCQB TFT LCD display (BF527 EZKIT)"
 612         depends on FB && BLACKFIN
 613         select BFIN_GPTIMERS
 614         select FB_CFB_FILLRECT
 615         select FB_CFB_COPYAREA
 616         select FB_CFB_IMAGEBLIT
 617         help
 618          This is the framebuffer device driver for a Varitronix VL-PS-COG-T350MCQB-01 display TFT LCD
 619          This display is a QVGA 320x240 24-bit RGB display interfaced by an 8-bit wide PPI
 620          It uses PPI[0..7] PPI_FS1, PPI_FS2 and PPI_CLK.
 621
 622 config FB_BFIN_LQ035Q1
 623         tristate "SHARP LQ035Q1DH02 TFT LCD"
 624         depends on FB && BLACKFIN && SPI
 625         select FB_CFB_FILLRECT
 626         select FB_CFB_COPYAREA
 627         select FB_CFB_IMAGEBLIT
 628         select BFIN_GPTIMERS
 629         help
 630           This is the framebuffer device driver for a SHARP LQ035Q1DH02 TFT display found on
 631           the Blackfin Landscape LCD EZ-Extender Card.
 632           This display is a QVGA 320x240 18-bit RGB display interfaced by an 16-bit wide PPI
 633           It uses PPI[0..15] PPI_FS1, PPI_FS2 and PPI_CLK.
 634
 635           To compile this driver as a module, choose M here: the
 636           module will be called bfin-lq035q1-fb.
 637
 638 config FB_STI
 639         tristate "HP STI frame buffer device support"
 640         depends on FB && PARISC
 641         select FB_CFB_FILLRECT
 642         select FB_CFB_COPYAREA
 643         select FB_CFB_IMAGEBLIT
 644         select STI_CONSOLE
 645         select VT
 646         default y
 647         ---help---
 648           STI refers to the HP "Standard Text Interface" which is a set of
 649           BIOS routines contained in a ROM chip in HP PA-RISC based machines.
 650           Enabling this option will implement the linux framebuffer device
 651           using calls to the STI BIOS routines for initialisation.
 652
 653           If you enable this option, you will get a planar framebuffer device
 654           /dev/fb which will work on the most common HP graphic cards of the
 655           NGLE family, including the artist chips (in the 7xx and Bxxx series),
 656           HCRX, HCRX24, CRX, CRX24 and VisEG series.
 657
 658           It is safe to enable this option, so you should probably say "Y".
 659
 660 config FB_MAC
 661         bool "Generic Macintosh display support"
 662         depends on (FB = y) && MAC
 663         select FB_CFB_FILLRECT
 664         select FB_CFB_COPYAREA
 665         select FB_CFB_IMAGEBLIT
 666         select FB_MACMODES
 667
 668 config FB_HP300
 669         bool
 670         depends on (FB = y) && DIO
 671         select FB_CFB_IMAGEBLIT
 672         default y
 673
 674 config FB_TGA
 675         tristate "TGA/SFB+ framebuffer support"
 676         depends on FB && (ALPHA || TC)
 677         select FB_CFB_FILLRECT
 678         select FB_CFB_COPYAREA
 679         select FB_CFB_IMAGEBLIT
 680         select BITREVERSE
 681         ---help---
 682           This is the frame buffer device driver for generic TGA and SFB+
 683           graphic cards.  These include DEC ZLXp-E1, -E2 and -E3 PCI cards,
 684           also known as PBXGA-A, -B and -C, and DEC ZLX-E1, -E2 and -E3
 685           TURBOchannel cards, also known as PMAGD-A, -B and -C.
 686
 687           Due to hardware limitations ZLX-E2 and E3 cards are not supported
 688           for DECstation 5000/200 systems.  Additionally due to firmware
 689           limitations these cards may cause troubles with booting DECstation
 690           5000/240 and /260 systems, but are fully supported under Linux if
 691           you manage to get it going. ;-)
 692
 693           Say Y if you have one of those.
 694
 695 config FB_UVESA
 696         tristate "Userspace VESA VGA graphics support"
 697         depends on FB && CONNECTOR
 698         select FB_CFB_FILLRECT
 699         select FB_CFB_COPYAREA
 700         select FB_CFB_IMAGEBLIT
 701         select FB_MODE_HELPERS
 702         help
 703           This is the frame buffer driver for generic VBE 2.0 compliant
 704           graphic cards. It can also take advantage of VBE 3.0 features,
 705           such as refresh rate adjustment.
 706
 707           This driver generally provides more features than vesafb but
 708           requires a userspace helper application called 'v86d'. See
 709           <file:Documentation/fb/uvesafb.txt> for more information.
 710
 711           If unsure, say N.
 712
 713 config FB_VESA
 714         bool "VESA VGA graphics support"
 715         depends on (FB = y) && X86
 716         select FB_CFB_FILLRECT
 717         select FB_CFB_COPYAREA
 718         select FB_CFB_IMAGEBLIT
 719         select FB_BOOT_VESA_SUPPORT
 720         help
 721           This is the frame buffer device driver for generic VESA 2.0
 722           compliant graphic cards. The older VESA 1.2 cards are not supported.
 723           You will get a boot time penguin logo at no additional cost. Please
 724           read <file:Documentation/fb/vesafb.txt>. If unsure, say Y.
 725
 726 config FB_EFI
 727         bool "EFI-based Framebuffer Support"
 728         depends on (FB = y) && X86 && EFI
 729         select FB_CFB_FILLRECT
 730         select FB_CFB_COPYAREA
 731         select FB_CFB_IMAGEBLIT
 732         help
 733           This is the EFI frame buffer device driver. If the firmware on
 734           your platform is EFI 1.10 or UEFI 2.0, select Y to add support for
 735           using the EFI framebuffer as your console.
 736
 737 config FB_N411
 738        tristate "N411 Apollo/Hecuba devkit support"
 739        depends on FB && X86 && MMU
 740        select FB_SYS_FILLRECT
 741        select FB_SYS_COPYAREA
 742        select FB_SYS_IMAGEBLIT
 743        select FB_SYS_FOPS
 744        select FB_DEFERRED_IO
 745        select FB_HECUBA
 746        help
 747          This enables support for the Apollo display controller in its
 748          Hecuba form using the n411 devkit.
 749
 750 config FB_HGA
 751         tristate "Hercules mono graphics support"
 752         depends on FB && X86
 753         select FB_CFB_FILLRECT
 754         select FB_CFB_COPYAREA
 755         select FB_CFB_IMAGEBLIT
 756         help
 757           Say Y here if you have a Hercules mono graphics card.
 758
 759           To compile this driver as a module, choose M here: the
 760           module will be called hgafb.
 761
 762           As this card technology is 15 years old, most people will answer N
 763           here.
 764
 765 config FB_HGA_ACCEL
 766         bool "Hercules mono Acceleration functions (EXPERIMENTAL)"
 767         depends on FB_HGA && EXPERIMENTAL
 768         ---help---
 769         This will compile the Hercules mono graphics with
 770         acceleration functions.
 771
 772 config FB_SGIVW
 773         tristate "SGI Visual Workstation framebuffer support"
 774         depends on FB && X86_VISWS
 775         select FB_CFB_FILLRECT
 776         select FB_CFB_COPYAREA
 777         select FB_CFB_IMAGEBLIT
 778         help
 779           SGI Visual Workstation support for framebuffer graphics.
 780
 781 config FB_GBE
 782         bool "SGI Graphics Backend frame buffer support"
 783         depends on (FB = y) && (SGI_IP32 || X86_VISWS)
 784         select FB_CFB_FILLRECT
 785         select FB_CFB_COPYAREA
 786         select FB_CFB_IMAGEBLIT
 787         help
 788           This is the frame buffer device driver for SGI Graphics Backend.
 789           This chip is used in SGI O2 and Visual Workstation 320/540.
 790
 791 config FB_GBE_MEM
 792         int "Video memory size in MB"
 793         depends on FB_GBE
 794         default 4
 795         help
 796           This is the amount of memory reserved for the framebuffer,
 797           which can be any value between 1MB and 8MB.
 798
 799 config FB_SBUS
 800         bool "SBUS and UPA framebuffers"
 801         depends on (FB = y) && SPARC
 802         help
 803           Say Y if you want support for SBUS or UPA based frame buffer device.
 804
 805 config FB_BW2
 806         bool "BWtwo support"
 807         depends on (FB = y) && (SPARC && FB_SBUS)
 808         select FB_CFB_FILLRECT
 809         select FB_CFB_COPYAREA
 810         select FB_CFB_IMAGEBLIT
 811         help
 812           This is the frame buffer device driver for the BWtwo frame buffer.
 813
 814 config FB_CG3
 815         bool "CGthree support"
 816         depends on (FB = y) && (SPARC && FB_SBUS)
 817         select FB_CFB_FILLRECT
 818         select FB_CFB_COPYAREA
 819         select FB_CFB_IMAGEBLIT
 820         help
 821           This is the frame buffer device driver for the CGthree frame buffer.
 822
 823 config FB_CG6
 824         bool "CGsix (GX,TurboGX) support"
 825         depends on (FB = y) && (SPARC && FB_SBUS)
 826         select FB_CFB_COPYAREA
 827         select FB_CFB_IMAGEBLIT
 828         help
 829           This is the frame buffer device driver for the CGsix (GX, TurboGX)
 830           frame buffer.
 831
 832 config FB_FFB
 833         bool "Creator/Creator3D/Elite3D support"
 834         depends on FB_SBUS && SPARC64
 835         select FB_CFB_COPYAREA
 836         select FB_CFB_IMAGEBLIT
 837         help
 838           This is the frame buffer device driver for the Creator, Creator3D,
 839           and Elite3D graphics boards.
 840
 841 config FB_TCX
 842         bool "TCX (SS4/SS5 only) support"
 843         depends on FB_SBUS
 844         select FB_CFB_FILLRECT
 845         select FB_CFB_COPYAREA
 846         select FB_CFB_IMAGEBLIT
 847         help
 848           This is the frame buffer device driver for the TCX 24/8bit frame
 849           buffer.
 850
 851 config FB_CG14
 852         bool "CGfourteen (SX) support"
 853         depends on FB_SBUS
 854         select FB_CFB_FILLRECT
 855         select FB_CFB_COPYAREA
 856         select FB_CFB_IMAGEBLIT
 857         help
 858           This is the frame buffer device driver for the CGfourteen frame
 859           buffer on Desktop SPARCsystems with the SX graphics option.
 860
 861 config FB_P9100
 862         bool "P9100 (Sparcbook 3 only) support"
 863         depends on FB_SBUS
 864         select FB_CFB_FILLRECT
 865         select FB_CFB_COPYAREA
 866         select FB_CFB_IMAGEBLIT
 867         help
 868           This is the frame buffer device driver for the P9100 card
 869           supported on Sparcbook 3 machines.
 870
 871 config FB_LEO
 872         bool "Leo (ZX) support"
 873         depends on FB_SBUS
 874         select FB_CFB_FILLRECT
 875         select FB_CFB_COPYAREA
 876         select FB_CFB_IMAGEBLIT
 877         help
 878           This is the frame buffer device driver for the SBUS-based Sun ZX
 879           (leo) frame buffer cards.
 880
 881 config FB_IGA
 882         bool "IGA 168x display support"
 883         depends on (FB = y) && SPARC32
 884         select FB_CFB_FILLRECT
 885         select FB_CFB_COPYAREA
 886         select FB_CFB_IMAGEBLIT
 887         help
 888           This is the framebuffer device for the INTERGRAPHICS 1680 and
 889           successor frame buffer cards.
 890
 891 config FB_XVR500
 892         bool "Sun XVR-500 3DLABS Wildcat support"
 893         depends on (FB = y) && PCI && SPARC64
 894         select FB_CFB_FILLRECT
 895         select FB_CFB_COPYAREA
 896         select FB_CFB_IMAGEBLIT
 897         help
 898           This is the framebuffer device for the Sun XVR-500 and similar
 899           graphics cards based upon the 3DLABS Wildcat chipset.  The driver
 900           only works on sparc64 systems where the system firmware has
 901           mostly initialized the card already.  It is treated as a
 902           completely dumb framebuffer device.
 903
 904 config FB_XVR2500
 905         bool "Sun XVR-2500 3DLABS Wildcat support"
 906         depends on (FB = y) && PCI && SPARC64
 907         select FB_CFB_FILLRECT
 908         select FB_CFB_COPYAREA
 909         select FB_CFB_IMAGEBLIT
 910         help
 911           This is the framebuffer device for the Sun XVR-2500 and similar
 912           graphics cards based upon the 3DLABS Wildcat chipset.  The driver
 913           only works on sparc64 systems where the system firmware has
 914           mostly initialized the card already.  It is treated as a
 915           completely dumb framebuffer device.
 916
 917 config FB_XVR1000
 918         bool "Sun XVR-1000 support"
 919         depends on (FB = y) && SPARC64
 920         select FB_CFB_FILLRECT
 921         select FB_CFB_COPYAREA
 922         select FB_CFB_IMAGEBLIT
 923         help
 924           This is the framebuffer device for the Sun XVR-1000 and similar
 925           graphics cards.  The driver only works on sparc64 systems where
 926           the system firmware has mostly initialized the card already.  It
 927           is treated as a completely dumb framebuffer device.
 928
 929 config FB_PVR2
 930         tristate "NEC PowerVR 2 display support"
 931         depends on FB && SH_DREAMCAST
 932         select FB_CFB_FILLRECT
 933         select FB_CFB_COPYAREA
 934         select FB_CFB_IMAGEBLIT
 935         ---help---
 936           Say Y here if you have a PowerVR 2 card in your box.  If you plan to
 937           run linux on your Dreamcast, you will have to say Y here.
 938           This driver may or may not work on other PowerVR 2 cards, but is
 939           totally untested.  Use at your own risk.  If unsure, say N.
 940
 941           To compile this driver as a module, choose M here: the
 942           module will be called pvr2fb.
 943
 944           You can pass several parameters to the driver at boot time or at
 945           module load time.  The parameters look like "video=pvr2:XXX", where
 946           the meaning of XXX can be found at the end of the main source file
 947           (<file:drivers/video/pvr2fb.c>). Please see the file
 948           <file:Documentation/fb/pvr2fb.txt>.
 949
 950 config FB_EPSON1355
 951         bool "Epson 1355 framebuffer support"
 952         depends on (FB = y) && ARCH_CEIVA
 953         select FB_CFB_FILLRECT
 954         select FB_CFB_COPYAREA
 955         select FB_CFB_IMAGEBLIT
 956         help
 957           Build in support for the SED1355 Epson Research Embedded RAMDAC
 958           LCD/CRT Controller (since redesignated as the S1D13505) as a
 959           framebuffer.  Product specs at
 960           <http://vdc.epson.com/>.
 961
 962 config FB_S1D13XXX
 963         tristate "Epson S1D13XXX framebuffer support"
 964         depends on FB
 965         select FB_CFB_FILLRECT
 966         select FB_CFB_COPYAREA
 967         select FB_CFB_IMAGEBLIT
 968         help
 969           Support for S1D13XXX framebuffer device family (currently only
 970           working with S1D13806). Product specs at
 971           <http://vdc.epson.com/>
 972
 973 config FB_ATMEL
 974         tristate "AT91/AT32 LCD Controller support"
 975         depends on FB && HAVE_FB_ATMEL
 976         select FB_CFB_FILLRECT
 977         select FB_CFB_COPYAREA
 978         select FB_CFB_IMAGEBLIT
 979         help
 980           This enables support for the AT91/AT32 LCD Controller.
 981
 982 config FB_INTSRAM
 983         bool "Frame Buffer in internal SRAM"
 984         depends on FB_ATMEL && ARCH_AT91SAM9261
 985         help
 986           Say Y if you want to map Frame Buffer in internal SRAM. Say N if you want
 987           to let frame buffer in external SDRAM.
 988
 989 config FB_ATMEL_STN
 990         bool "Use a STN display with AT91/AT32 LCD Controller"
 991         depends on FB_ATMEL && (MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK)
 992         default n
 993         help
 994           Say Y if you want to connect a STN LCD display to the AT91/AT32 LCD
 995           Controller. Say N if you want to connect a TFT.
 996
 997           If unsure, say N.
 998
 999 config FB_NVIDIA
1000         tristate "nVidia Framebuffer Support"
1001         depends on FB && PCI
1002         select FB_BACKLIGHT if FB_NVIDIA_BACKLIGHT
1003         select FB_MODE_HELPERS
1004         select FB_CFB_FILLRECT
1005         select FB_CFB_COPYAREA
1006         select FB_CFB_IMAGEBLIT
1007         select BITREVERSE
1008         select VGASTATE
1009         help
1010           This driver supports graphics boards with the nVidia chips, TNT
1011           and newer. For very old chipsets, such as the RIVA128, then use
1012           the rivafb.
1013           Say Y if you have such a graphics board.
1014
1015           To compile this driver as a module, choose M here: the
1016           module will be called nvidiafb.
1017
1018 config FB_NVIDIA_I2C
1019        bool "Enable DDC Support"
1020        depends on FB_NVIDIA
1021        select FB_DDC
1022        help
1023           This enables I2C support for nVidia Chipsets.  This is used
1024           only for getting EDID information from the attached display
1025           allowing for robust video mode handling and switching.
1026
1027           Because fbdev-2.6 requires that drivers must be able to
1028           independently validate video mode parameters, you should say Y
1029           here.
1030
1031 config FB_NVIDIA_DEBUG
1032         bool "Lots of debug output"
1033         depends on FB_NVIDIA
1034         default n
1035         help
1036           Say Y here if you want the nVidia driver to output all sorts
1037           of debugging information to provide to the maintainer when
1038           something goes wrong.
1039
1040 config FB_NVIDIA_BACKLIGHT
1041         bool "Support for backlight control"
1042         depends on FB_NVIDIA
1043         default y
1044         help
1045           Say Y here if you want to control the backlight of your display.
1046
1047 config FB_RIVA
1048         tristate "nVidia Riva support"
1049         depends on FB && PCI
1050         select FB_BACKLIGHT if FB_RIVA_BACKLIGHT
1051         select FB_MODE_HELPERS
1052         select FB_CFB_FILLRECT
1053         select FB_CFB_COPYAREA
1054         select FB_CFB_IMAGEBLIT
1055         select BITREVERSE
1056         select VGASTATE
1057         help
1058           This driver supports graphics boards with the nVidia Riva/Geforce
1059           chips.
1060           Say Y if you have such a graphics board.
1061
1062           To compile this driver as a module, choose M here: the
1063           module will be called rivafb.
1064
1065 config FB_RIVA_I2C
1066        bool "Enable DDC Support"
1067        depends on FB_RIVA
1068        select FB_DDC
1069        help
1070           This enables I2C support for nVidia Chipsets.  This is used
1071           only for getting EDID information from the attached display
1072           allowing for robust video mode handling and switching.
1073
1074           Because fbdev-2.6 requires that drivers must be able to
1075           independently validate video mode parameters, you should say Y
1076           here.
1077
1078 config FB_RIVA_DEBUG
1079         bool "Lots of debug output"
1080         depends on FB_RIVA
1081         default n
1082         help
1083           Say Y here if you want the Riva driver to output all sorts
1084           of debugging information to provide to the maintainer when
1085           something goes wrong.
1086
1087 config FB_RIVA_BACKLIGHT
1088         bool "Support for backlight control"
1089         depends on FB_RIVA
1090         default y
1091         help
1092           Say Y here if you want to control the backlight of your display.
1093
1094 config FB_I810
1095         tristate "Intel 810/815 support (EXPERIMENTAL)"
1096         depends on EXPERIMENTAL && FB && PCI && X86_32 && AGP_INTEL
1097         select FB_MODE_HELPERS
1098         select FB_CFB_FILLRECT
1099         select FB_CFB_COPYAREA
1100         select FB_CFB_IMAGEBLIT
1101         select VGASTATE
1102         help
1103           This driver supports the on-board graphics built in to the Intel 810
1104           and 815 chipsets.  Say Y if you have and plan to use such a board.
1105
1106           To compile this driver as a module, choose M here: the
1107           module will be called i810fb.
1108
1109           For more information, please read
1110           <file:Documentation/fb/intel810.txt>
1111
1112 config FB_I810_GTF
1113         bool "use VESA Generalized Timing Formula"
1114         depends on FB_I810
1115         help
1116           If you say Y, then the VESA standard, Generalized Timing Formula
1117           or GTF, will be used to calculate the required video timing values
1118           per video mode.  Since the GTF allows nondiscrete timings
1119           (nondiscrete being a range of values as opposed to discrete being a
1120           set of values), you'll be able to use any combination of horizontal
1121           and vertical resolutions, and vertical refresh rates without having
1122           to specify your own timing parameters.  This is especially useful
1123           to maximize the performance of an aging display, or if you just
1124           have a display with nonstandard dimensions. A VESA compliant
1125           monitor is recommended, but can still work with non-compliant ones.
1126           If you need or want this, then select this option. The timings may
1127           not be compliant with Intel's recommended values. Use at your own
1128           risk.
1129
1130           If you say N, the driver will revert to discrete video timings
1131           using a set recommended by Intel in their documentation.
1132
1133           If unsure, say N.
1134
1135 config FB_I810_I2C
1136         bool "Enable DDC Support"
1137         depends on FB_I810 && FB_I810_GTF
1138         select FB_DDC
1139         help
1140
1141 config FB_LE80578
1142         tristate "Intel LE80578 (Vermilion) support"
1143         depends on FB && PCI && X86
1144         select FB_MODE_HELPERS
1145         select FB_CFB_FILLRECT
1146         select FB_CFB_COPYAREA
1147         select FB_CFB_IMAGEBLIT
1148         help
1149           This driver supports the LE80578 (Vermilion Range) chipset
1150
1151 config FB_CARILLO_RANCH
1152         tristate "Intel Carillo Ranch support"
1153         depends on FB_LE80578 && FB && PCI && X86
1154         help
1155           This driver supports the LE80578 (Carillo Ranch) board
1156
1157 config FB_INTEL
1158         tristate "Intel 830M/845G/852GM/855GM/865G/915G/945G/945GM/965G/965GM support (EXPERIMENTAL)"
1159         depends on EXPERIMENTAL && FB && PCI && X86 && AGP_INTEL && EMBEDDED
1160         select FB_MODE_HELPERS
1161         select FB_CFB_FILLRECT
1162         select FB_CFB_COPYAREA
1163         select FB_CFB_IMAGEBLIT
1164         select FB_BOOT_VESA_SUPPORT if FB_INTEL = y
1165         depends on !DRM_I915
1166         help
1167           This driver supports the on-board graphics built in to the Intel
1168           830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM/965G/965GM chipsets.
1169           Say Y if you have and plan to use such a board.
1170
1171           To make FB_INTELFB=Y work you need to say AGP_INTEL=y too.
1172
1173           To compile this driver as a module, choose M here: the
1174           module will be called intelfb.
1175
1176           For more information, please read <file:Documentation/fb/intelfb.txt>
1177
1178 config FB_INTEL_DEBUG
1179         bool "Intel driver Debug Messages"
1180         depends on FB_INTEL
1181         ---help---
1182           Say Y here if you want the Intel driver to output all sorts
1183           of debugging information to provide to the maintainer when
1184           something goes wrong.
1185
1186 config FB_INTEL_I2C
1187         bool "DDC/I2C for Intel framebuffer support"
1188         depends on FB_INTEL
1189         select FB_DDC
1190         default y
1191         help
1192           Say Y here if you want DDC/I2C support for your on-board Intel graphics.
1193
1194 config FB_MATROX
1195         tristate "Matrox acceleration"
1196         depends on FB && PCI
1197         select FB_CFB_FILLRECT
1198         select FB_CFB_COPYAREA
1199         select FB_CFB_IMAGEBLIT
1200         select FB_TILEBLITTING
1201         select FB_MACMODES if PPC_PMAC
1202         ---help---
1203           Say Y here if you have a Matrox Millennium, Matrox Millennium II,
1204           Matrox Mystique, Matrox Mystique 220, Matrox Productiva G100, Matrox
1205           Mystique G200, Matrox Millennium G200, Matrox Marvel G200 video,
1206           Matrox G400, G450 or G550 card in your box.
1207
1208           To compile this driver as a module, choose M here: the
1209           module will be called matroxfb.
1210
1211           You can pass several parameters to the driver at boot time or at
1212           module load time. The parameters look like "video=matrox:XXX", and
1213           are described in <file:Documentation/fb/matroxfb.txt>.
1214
1215 config FB_MATROX_MILLENIUM
1216         bool "Millennium I/II support"
1217         depends on FB_MATROX
1218         help
1219           Say Y here if you have a Matrox Millennium or Matrox Millennium II
1220           video card. If you select "Advanced lowlevel driver options" below,
1221           you should check 4 bpp packed pixel, 8 bpp packed pixel, 16 bpp
1222           packed pixel, 24 bpp packed pixel and 32 bpp packed pixel. You can
1223           also use font widths different from 8.
1224
1225 config FB_MATROX_MYSTIQUE
1226         bool "Mystique support"
1227         depends on FB_MATROX
1228         help
1229           Say Y here if you have a Matrox Mystique or Matrox Mystique 220
1230           video card. If you select "Advanced lowlevel driver options" below,
1231           you should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp
1232           packed pixel and 32 bpp packed pixel. You can also use font widths
1233           different from 8.
1234
1235 config FB_MATROX_G
1236         bool "G100/G200/G400/G450/G550 support"
1237         depends on FB_MATROX
1238         ---help---
1239           Say Y here if you have a Matrox G100, G200, G400, G450 or G550 based
1240           video card. If you select "Advanced lowlevel driver options", you
1241           should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp packed
1242           pixel and 32 bpp packed pixel. You can also use font widths
1243           different from 8.
1244
1245           If you need support for G400 secondary head, you must say Y to
1246           "Matrox I2C support" and "G400 second head support" right below.
1247           G450/G550 secondary head and digital output are supported without
1248           additional modules.
1249
1250           The driver starts in monitor mode. You must use the matroxset tool
1251           (available at <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to
1252           swap primary and secondary head outputs, or to change output mode.
1253           Secondary head driver always start in 640x480 resolution and you
1254           must use fbset to change it.
1255
1256           Do not forget that second head supports only 16 and 32 bpp
1257           packed pixels, so it is a good idea to compile them into the kernel
1258           too. You can use only some font widths, as the driver uses generic
1259           painting procedures (the secondary head does not use acceleration
1260           engine).
1261
1262           G450/G550 hardware can display TV picture only from secondary CRTC,
1263           and it performs no scaling, so picture must have 525 or 625 lines.
1264
1265 config FB_MATROX_I2C
1266         tristate "Matrox I2C support"
1267         depends on FB_MATROX
1268         select FB_DDC
1269         ---help---
1270           This drivers creates I2C buses which are needed for accessing the
1271           DDC (I2C) bus present on all Matroxes, an I2C bus which
1272           interconnects Matrox optional devices, like MGA-TVO on G200 and
1273           G400, and the secondary head DDC bus, present on G400 only.
1274
1275           You can say Y or M here if you want to experiment with monitor
1276           detection code. You must say Y or M here if you want to use either
1277           second head of G400 or MGA-TVO on G200 or G400.
1278
1279           If you compile it as module, it will create a module named
1280           i2c-matroxfb.
1281
1282 config FB_MATROX_MAVEN
1283         tristate "G400 second head support"
1284         depends on FB_MATROX_G && FB_MATROX_I2C
1285         ---help---
1286           WARNING !!! This support does not work with G450 !!!
1287
1288           Say Y or M here if you want to use a secondary head (meaning two
1289           monitors in parallel) on G400 or MGA-TVO add-on on G200. Secondary
1290           head is not compatible with accelerated XFree 3.3.x SVGA servers -
1291           secondary head output is blanked while you are in X. With XFree
1292           3.9.17 preview you can use both heads if you use SVGA over fbdev or
1293           the fbdev driver on first head and the fbdev driver on second head.
1294
1295           If you compile it as module, two modules are created,
1296           matroxfb_crtc2 and matroxfb_maven. Matroxfb_maven is needed for
1297           both G200 and G400, matroxfb_crtc2 is needed only by G400. You must
1298           also load i2c-matroxfb to get it to run.
1299
1300           The driver starts in monitor mode and you must use the matroxset
1301           tool (available at
1302           <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to switch it to
1303           PAL or NTSC or to swap primary and secondary head outputs.
1304           Secondary head driver also always start in 640x480 resolution, you
1305           must use fbset to change it.
1306
1307           Also do not forget that second head supports only 16 and 32 bpp
1308           packed pixels, so it is a good idea to compile them into the kernel
1309           too.  You can use only some font widths, as the driver uses generic
1310           painting procedures (the secondary head does not use acceleration
1311           engine).
1312
1313 config FB_RADEON
1314         tristate "ATI Radeon display support"
1315         depends on FB && PCI
1316         select FB_BACKLIGHT if FB_RADEON_BACKLIGHT
1317         select FB_MODE_HELPERS
1318         select FB_CFB_FILLRECT
1319         select FB_CFB_COPYAREA
1320         select FB_CFB_IMAGEBLIT
1321         select FB_MACMODES if PPC_OF
1322         help
1323           Choose this option if you want to use an ATI Radeon graphics card as
1324           a framebuffer device.  There are both PCI and AGP versions.  You
1325           don't need to choose this to run the Radeon in plain VGA mode.
1326
1327           There is a product page at
1328           http://products.amd.com/en-us/GraphicCardResult.aspx
1329
1330 config FB_RADEON_I2C
1331         bool "DDC/I2C for ATI Radeon support"
1332         depends on FB_RADEON
1333         select FB_DDC
1334         default y
1335         help
1336           Say Y here if you want DDC/I2C support for your Radeon board.
1337
1338 config FB_RADEON_BACKLIGHT
1339         bool "Support for backlight control"
1340         depends on FB_RADEON
1341         default y
1342         help
1343           Say Y here if you want to control the backlight of your display.
1344
1345 config FB_RADEON_DEBUG
1346         bool "Lots of debug output from Radeon driver"
1347         depends on FB_RADEON
1348         default n
1349         help
1350           Say Y here if you want the Radeon driver to output all sorts
1351           of debugging information to provide to the maintainer when
1352           something goes wrong.
1353
1354 config FB_ATY128
1355         tristate "ATI Rage128 display support"
1356         depends on FB && PCI
1357         select FB_CFB_FILLRECT
1358         select FB_CFB_COPYAREA
1359         select FB_CFB_IMAGEBLIT
1360         select FB_BACKLIGHT if FB_ATY128_BACKLIGHT
1361         select FB_MACMODES if PPC_PMAC
1362         help
1363           This driver supports graphics boards with the ATI Rage128 chips.
1364           Say Y if you have such a graphics board and read
1365           <file:Documentation/fb/aty128fb.txt>.
1366
1367           To compile this driver as a module, choose M here: the
1368           module will be called aty128fb.
1369
1370 config FB_ATY128_BACKLIGHT
1371         bool "Support for backlight control"
1372         depends on FB_ATY128
1373         default y
1374         help
1375           Say Y here if you want to control the backlight of your display.
1376
1377 config FB_ATY
1378         tristate "ATI Mach64 display support" if PCI || ATARI
1379         depends on FB && !SPARC32
1380         select FB_CFB_FILLRECT
1381         select FB_CFB_COPYAREA
1382         select FB_CFB_IMAGEBLIT
1383         select FB_BACKLIGHT if FB_ATY_BACKLIGHT
1384         select FB_MACMODES if PPC
1385         help
1386           This driver supports graphics boards with the ATI Mach64 chips.
1387           Say Y if you have such a graphics board.
1388
1389           To compile this driver as a module, choose M here: the
1390           module will be called atyfb.
1391
1392 config FB_ATY_CT
1393         bool "Mach64 CT/VT/GT/LT (incl. 3D RAGE) support"
1394         depends on PCI && FB_ATY
1395         default y if SPARC64 && PCI
1396         help
1397           Say Y here to support use of ATI's 64-bit Rage boards (or other
1398           boards based on the Mach64 CT, VT, GT, and LT chipsets) as a
1399           framebuffer device.  The ATI product support page for these boards
1400           is at <http://support.ati.com/products/pc/mach64/mach64.html>.
1401
1402 config FB_ATY_GENERIC_LCD
1403         bool "Mach64 generic LCD support (EXPERIMENTAL)"
1404         depends on FB_ATY_CT
1405         help
1406           Say Y if you have a laptop with an ATI Rage LT PRO, Rage Mobility,
1407           Rage XC, or Rage XL chipset.
1408
1409 config FB_ATY_GX
1410         bool "Mach64 GX support" if PCI
1411         depends on FB_ATY
1412         default y if ATARI
1413         help
1414           Say Y here to support use of the ATI Mach64 Graphics Expression
1415           board (or other boards based on the Mach64 GX chipset) as a
1416           framebuffer device.  The ATI product support page for these boards
1417           is at
1418           <http://support.ati.com/products/pc/mach64/graphics_xpression.html>.
1419
1420 config FB_ATY_BACKLIGHT
1421         bool "Support for backlight control"
1422         depends on FB_ATY
1423         default y
1424         help
1425           Say Y here if you want to control the backlight of your display.
1426
1427 config FB_S3
1428         tristate "S3 Trio/Virge support"
1429         depends on FB && PCI
1430         select FB_CFB_FILLRECT
1431         select FB_CFB_COPYAREA
1432         select FB_CFB_IMAGEBLIT
1433         select FB_TILEBLITTING
1434         select FB_SVGALIB
1435         select VGASTATE
1436         select FONT_8x16 if FRAMEBUFFER_CONSOLE
1437         ---help---
1438           Driver for graphics boards with S3 Trio / S3 Virge chip.
1439
1440 config FB_SAVAGE
1441         tristate "S3 Savage support"
1442         depends on FB && PCI && EXPERIMENTAL
1443         select FB_MODE_HELPERS
1444         select FB_CFB_FILLRECT
1445         select FB_CFB_COPYAREA
1446         select FB_CFB_IMAGEBLIT
1447         select VGASTATE
1448         help
1449           This driver supports notebooks and computers with S3 Savage PCI/AGP
1450           chips.
1451
1452           Say Y if you have such a graphics card.
1453
1454           To compile this driver as a module, choose M here; the module
1455           will be called savagefb.
1456
1457 config FB_SAVAGE_I2C
1458        bool "Enable DDC2 Support"
1459        depends on FB_SAVAGE
1460        select FB_DDC
1461        help
1462           This enables I2C support for S3 Savage Chipsets.  This is used
1463           only for getting EDID information from the attached display
1464           allowing for robust video mode handling and switching.
1465
1466           Because fbdev-2.6 requires that drivers must be able to
1467           independently validate video mode parameters, you should say Y
1468           here.
1469
1470 config FB_SAVAGE_ACCEL
1471        bool "Enable Console Acceleration"
1472        depends on FB_SAVAGE
1473        default n
1474        help
1475           This option will compile in console acceleration support. If
1476           the resulting framebuffer console has bothersome glitches, then
1477           choose N here.
1478
1479 config FB_SIS
1480         tristate "SiS/XGI display support"
1481         depends on FB && PCI
1482         select FB_CFB_FILLRECT
1483         select FB_CFB_COPYAREA
1484         select FB_CFB_IMAGEBLIT
1485         select FB_BOOT_VESA_SUPPORT if FB_SIS = y
1486         help
1487           This is the frame buffer device driver for the SiS 300, 315, 330
1488           and 340 series as well as XGI V3XT, V5, V8, Z7 graphics chipsets.
1489           Specs available at <http://www.sis.com> and <http://www.xgitech.com>.
1490
1491           To compile this driver as a module, choose M here; the module
1492           will be called sisfb.
1493
1494 config FB_SIS_300
1495         bool "SiS 300 series support"
1496         depends on FB_SIS
1497         help
1498           Say Y here to support use of the SiS 300/305, 540, 630 and 730.
1499
1500 config FB_SIS_315
1501         bool "SiS 315/330/340 series and XGI support"
1502         depends on FB_SIS
1503         help
1504           Say Y here to support use of the SiS 315, 330 and 340 series
1505           (315/H/PRO, 55x, 650, 651, 740, 330, 661, 741, 760, 761) as well
1506           as XGI V3XT, V5, V8 and Z7.
1507
1508 config FB_VIA
1509        tristate "VIA UniChrome (Pro) and Chrome9 display support"
1510        depends on FB && PCI && X86
1511        select FB_CFB_FILLRECT
1512        select FB_CFB_COPYAREA
1513        select FB_CFB_IMAGEBLIT
1514        select I2C_ALGOBIT
1515        select I2C
1516        select GPIOLIB
1517        help
1518           This is the frame buffer device driver for Graphics chips of VIA
1519           UniChrome (Pro) Family (CLE266,PM800/CN400,P4M800CE/P4M800Pro/
1520           CN700/VN800,CX700/VX700,P4M890) and Chrome9 Family (K8M890,CN896
1521           /P4M900,VX800)
1522           Say Y if you have a VIA UniChrome graphics board.
1523
1524           To compile this driver as a module, choose M here: the
1525           module will be called viafb.
1526
1527 if FB_VIA
1528
1529 config FB_VIA_DIRECT_PROCFS
1530         bool "direct hardware access via procfs (DEPRECATED)(DANGEROUS)"
1531         depends on FB_VIA
1532         default n
1533         help
1534           Allow direct hardware access to some output registers via procfs.
1535           This is dangerous but may provide the only chance to get the
1536           correct output device configuration.
1537           Its use is strongly discouraged.
1538
1539 endif
1540
1541 config FB_NEOMAGIC
1542         tristate "NeoMagic display support"
1543         depends on FB && PCI
1544         select FB_MODE_HELPERS
1545         select FB_CFB_FILLRECT
1546         select FB_CFB_COPYAREA
1547         select FB_CFB_IMAGEBLIT
1548         select VGASTATE
1549         help
1550           This driver supports notebooks with NeoMagic PCI chips.
1551           Say Y if you have such a graphics card.
1552
1553           To compile this driver as a module, choose M here: the
1554           module will be called neofb.
1555
1556 config FB_KYRO
1557         tristate "IMG Kyro support"
1558         depends on FB && PCI
1559         select FB_CFB_FILLRECT
1560         select FB_CFB_COPYAREA
1561         select FB_CFB_IMAGEBLIT
1562         help
1563           Say Y here if you have a STG4000 / Kyro / PowerVR 3 based
1564           graphics board.
1565
1566           To compile this driver as a module, choose M here: the
1567           module will be called kyrofb.
1568
1569 config FB_3DFX
1570         tristate "3Dfx Banshee/Voodoo3/Voodoo5 display support"
1571         depends on FB && PCI
1572         select FB_CFB_IMAGEBLIT
1573         select FB_CFB_FILLRECT
1574         select FB_CFB_COPYAREA
1575         select FB_MODE_HELPERS
1576         help
1577           This driver supports graphics boards with the 3Dfx Banshee,
1578           Voodoo3 or VSA-100 (aka Voodoo4/5) chips. Say Y if you have
1579           such a graphics board.
1580
1581           To compile this driver as a module, choose M here: the
1582           module will be called tdfxfb.
1583
1584 config FB_3DFX_ACCEL
1585         bool "3Dfx Acceleration functions (EXPERIMENTAL)"
1586         depends on FB_3DFX && EXPERIMENTAL
1587         ---help---
1588         This will compile the 3Dfx Banshee/Voodoo3/VSA-100 frame buffer
1589         device driver with acceleration functions.
1590
1591 config FB_3DFX_I2C
1592         bool "Enable DDC/I2C support"
1593         depends on FB_3DFX && EXPERIMENTAL
1594         select FB_DDC
1595         default y
1596         help
1597           Say Y here if you want DDC/I2C support for your 3dfx Voodoo3.
1598
1599 config FB_VOODOO1
1600         tristate "3Dfx Voodoo Graphics (sst1) support"
1601         depends on FB && PCI
1602         select FB_CFB_FILLRECT
1603         select FB_CFB_COPYAREA
1604         select FB_CFB_IMAGEBLIT
1605         ---help---
1606           Say Y here if you have a 3Dfx Voodoo Graphics (Voodoo1/sst1) or
1607           Voodoo2 (cvg) based graphics card.
1608
1609           To compile this driver as a module, choose M here: the
1610           module will be called sstfb.
1611
1612           WARNING: Do not use any application that uses the 3D engine
1613           (namely glide) while using this driver.
1614           Please read the <file:Documentation/fb/sstfb.txt> for supported
1615           options and other important info  support.
1616
1617 config FB_VT8623
1618         tristate "VIA VT8623 support"
1619         depends on FB && PCI
1620         select FB_CFB_FILLRECT
1621         select FB_CFB_COPYAREA
1622         select FB_CFB_IMAGEBLIT
1623         select FB_TILEBLITTING
1624         select FB_SVGALIB
1625         select VGASTATE
1626         select FONT_8x16 if FRAMEBUFFER_CONSOLE
1627         ---help---
1628           Driver for CastleRock integrated graphics core in the
1629           VIA VT8623 [Apollo CLE266] chipset.
1630
1631 config FB_TRIDENT
1632         tristate "Trident/CyberXXX/CyberBlade support"
1633         depends on FB && PCI
1634         select FB_CFB_FILLRECT
1635         select FB_CFB_COPYAREA
1636         select FB_CFB_IMAGEBLIT
1637         ---help---
1638           This is the frame buffer device driver for Trident PCI/AGP chipsets.
1639           Supported chipset families are TGUI 9440/96XX, 3DImage, Blade3D
1640           and Blade XP.
1641           There are also integrated versions of these chips called CyberXXXX,
1642           CyberImage or CyberBlade. These chips are mostly found in laptops
1643           but also on some motherboards including early VIA EPIA motherboards.
1644           For more information, read <file:Documentation/fb/tridentfb.txt>
1645
1646           Say Y if you have such a graphics board.
1647
1648           To compile this driver as a module, choose M here: the
1649           module will be called tridentfb.
1650
1651 config FB_ARK
1652         tristate "ARK 2000PV support"
1653         depends on FB && PCI
1654         select FB_CFB_FILLRECT
1655         select FB_CFB_COPYAREA
1656         select FB_CFB_IMAGEBLIT
1657         select FB_TILEBLITTING
1658         select FB_SVGALIB
1659         select VGASTATE
1660         select FONT_8x16 if FRAMEBUFFER_CONSOLE
1661         ---help---
1662           Driver for PCI graphics boards with ARK 2000PV chip
1663           and ICS 5342 RAMDAC.
1664
1665 config FB_PM3
1666         tristate "Permedia3 support (EXPERIMENTAL)"
1667         depends on FB && PCI && EXPERIMENTAL
1668         select FB_CFB_FILLRECT
1669         select FB_CFB_COPYAREA
1670         select FB_CFB_IMAGEBLIT
1671         help
1672           This is the frame buffer device driver for the 3DLabs Permedia3
1673           chipset, used in Formac ProFormance III, 3DLabs Oxygen VX1 &
1674           similar boards, 3DLabs Permedia3 Create!, Appian Jeronimo 2000
1675           and maybe other boards.
1676
1677 config FB_CARMINE
1678         tristate "Fujitsu carmine frame buffer support"
1679         depends on FB && PCI
1680         select FB_CFB_FILLRECT
1681         select FB_CFB_COPYAREA
1682         select FB_CFB_IMAGEBLIT
1683         help
1684           This is the frame buffer device driver for the Fujitsu Carmine chip.
1685           The driver provides two independent frame buffer devices.
1686
1687 choice
1688         depends on FB_CARMINE
1689         prompt "DRAM timing"
1690         default FB_CARMINE_DRAM_EVAL
1691
1692 config FB_CARMINE_DRAM_EVAL
1693         bool "Eval board timings"
1694         help
1695           Use timings which work on the eval card.
1696
1697 config CARMINE_DRAM_CUSTOM
1698         bool "Custom board timings"
1699         help
1700           Use custom board timings.
1701 endchoice
1702
1703 config FB_AU1100
1704         bool "Au1100 LCD Driver"
1705         depends on (FB = y) && MIPS && SOC_AU1100
1706         select FB_CFB_FILLRECT
1707         select FB_CFB_COPYAREA
1708         select FB_CFB_IMAGEBLIT
1709         help
1710           This is the framebuffer driver for the AMD Au1100 SOC.  It can drive
1711           various panels and CRTs by passing in kernel cmd line option
1712           au1100fb:panel=<name>.
1713
1714 config FB_AU1200
1715         bool "Au1200 LCD Driver"
1716         depends on (FB = y) && MIPS && SOC_AU1200
1717         select FB_CFB_FILLRECT
1718         select FB_CFB_COPYAREA
1719         select FB_CFB_IMAGEBLIT
1720         help
1721           This is the framebuffer driver for the AMD Au1200 SOC.  It can drive
1722           various panels and CRTs by passing in kernel cmd line option
1723           au1200fb:panel=<name>.
1724
1725 source "drivers/video/geode/Kconfig"
1726
1727 config FB_HIT
1728         tristate "HD64461 Frame Buffer support"
1729         depends on FB && HD64461
1730         select FB_CFB_FILLRECT
1731         select FB_CFB_COPYAREA
1732         select FB_CFB_IMAGEBLIT
1733         help
1734           This is the frame buffer device driver for the Hitachi HD64461 LCD
1735           frame buffer card.
1736
1737 config FB_PMAG_AA
1738         bool "PMAG-AA TURBOchannel framebuffer support"
1739         depends on (FB = y) && TC
1740         select FB_CFB_FILLRECT
1741         select FB_CFB_COPYAREA
1742         select FB_CFB_IMAGEBLIT
1743         help
1744           Support for the PMAG-AA TURBOchannel framebuffer card (1280x1024x1)
1745           used mainly in the MIPS-based DECstation series.
1746
1747 config FB_PMAG_BA
1748         tristate "PMAG-BA TURBOchannel framebuffer support"
1749         depends on FB && TC
1750         select FB_CFB_FILLRECT
1751         select FB_CFB_COPYAREA
1752         select FB_CFB_IMAGEBLIT
1753         help
1754           Support for the PMAG-BA TURBOchannel framebuffer card (1024x864x8)
1755           used mainly in the MIPS-based DECstation series.
1756
1757 config FB_PMAGB_B
1758         tristate "PMAGB-B TURBOchannel framebuffer support"
1759         depends on FB && TC
1760         select FB_CFB_FILLRECT
1761         select FB_CFB_COPYAREA
1762         select FB_CFB_IMAGEBLIT
1763         help
1764           Support for the PMAGB-B TURBOchannel framebuffer card used mainly
1765           in the MIPS-based DECstation series. The card is currently only
1766           supported in 1280x1024x8 mode.
1767
1768 config FB_MAXINE
1769         bool "Maxine (Personal DECstation) onboard framebuffer support"
1770         depends on (FB = y) && MACH_DECSTATION
1771         select FB_CFB_FILLRECT
1772         select FB_CFB_COPYAREA
1773         select FB_CFB_IMAGEBLIT
1774         help
1775           Support for the onboard framebuffer (1024x768x8) in the Personal
1776           DECstation series (Personal DECstation 5000/20, /25, /33, /50,
1777           Codename "Maxine").
1778
1779 config FB_G364
1780         bool "G364 frame buffer support"
1781         depends on (FB = y) && (MIPS_MAGNUM_4000 || OLIVETTI_M700)
1782         select FB_CFB_FILLRECT
1783         select FB_CFB_COPYAREA
1784         select FB_CFB_IMAGEBLIT
1785         help
1786           The G364 driver is the framebuffer used in MIPS Magnum 4000 and
1787           Olivetti M700-10 systems.
1788
1789 config FB_68328
1790         bool "Motorola 68328 native frame buffer support"
1791         depends on (FB = y) && (M68328 || M68EZ328 || M68VZ328)
1792         select FB_CFB_FILLRECT
1793         select FB_CFB_COPYAREA
1794         select FB_CFB_IMAGEBLIT
1795         help
1796           Say Y here if you want to support the built-in frame buffer of
1797           the Motorola 68328 CPU family.
1798
1799 config FB_PXA168
1800         tristate "PXA168/910 LCD framebuffer support"
1801         depends on FB && (CPU_PXA168 || CPU_PXA910)
1802         select FB_CFB_FILLRECT
1803         select FB_CFB_COPYAREA
1804         select FB_CFB_IMAGEBLIT
1805         ---help---
1806           Frame buffer driver for the built-in LCD controller in the Marvell
1807           MMP processor.
1808
1809 config FB_PXA
1810         tristate "PXA LCD framebuffer support"
1811         depends on FB && ARCH_PXA
1812         select FB_CFB_FILLRECT
1813         select FB_CFB_COPYAREA
1814         select FB_CFB_IMAGEBLIT
1815         ---help---
1816           Frame buffer driver for the built-in LCD controller in the Intel
1817           PXA2x0 processor.
1818
1819           This driver is also available as a module ( = code which can be
1820           inserted and removed from the running kernel whenever you want). The
1821           module will be called pxafb. If you want to compile it as a module,
1822           say M here and read <file:Documentation/kbuild/modules.txt>.
1823
1824           If unsure, say N.
1825
1826 config FB_PXA_OVERLAY
1827         bool "Support PXA27x/PXA3xx Overlay(s) as framebuffer"
1828         default n
1829         depends on FB_PXA && (PXA27x || PXA3xx)
1830
1831 config FB_PXA_SMARTPANEL
1832         bool "PXA Smartpanel LCD support"
1833         default n
1834         depends on FB_PXA
1835
1836 config FB_PXA_PARAMETERS
1837         bool "PXA LCD command line parameters"
1838         default n
1839         depends on FB_PXA
1840         ---help---
1841           Enable the use of kernel command line or module parameters
1842           to configure the physical properties of the LCD panel when
1843           using the PXA LCD driver.
1844
1845           This option allows you to override the panel parameters
1846           supplied by the platform in order to support multiple
1847           different models of flatpanel. If you will only be using a
1848           single model of flatpanel then you can safely leave this
1849           option disabled.
1850
1851           <file:Documentation/fb/pxafb.txt> describes the available parameters.
1852
1853 config FB_MBX
1854         tristate "2700G LCD framebuffer support"
1855         depends on FB && ARCH_PXA
1856         select FB_CFB_FILLRECT
1857         select FB_CFB_COPYAREA
1858         select FB_CFB_IMAGEBLIT
1859         ---help---
1860           Framebuffer driver for the Intel 2700G (Marathon) Graphics
1861           Accelerator
1862
1863 config FB_MBX_DEBUG
1864        bool "Enable debugging info via debugfs"
1865        depends on FB_MBX && DEBUG_FS
1866        default n
1867        ---help---
1868          Enable this if you want debugging information using the debug
1869          filesystem (debugfs)
1870
1871          If unsure, say N.
1872
1873 config FB_FSL_DIU
1874         tristate "Freescale DIU framebuffer support"
1875         depends on FB && FSL_SOC
1876         select FB_MODE_HELPERS
1877         select FB_CFB_FILLRECT
1878         select FB_CFB_COPYAREA
1879         select FB_CFB_IMAGEBLIT
1880         select PPC_LIB_RHEAP
1881         ---help---
1882           Framebuffer driver for the Freescale SoC DIU
1883
1884 config FB_W100
1885         tristate "W100 frame buffer support"
1886         depends on FB && ARCH_PXA
1887         select FB_CFB_FILLRECT
1888         select FB_CFB_COPYAREA
1889         select FB_CFB_IMAGEBLIT
1890         ---help---
1891           Frame buffer driver for the w100 as found on the Sharp SL-Cxx series.
1892           It can also drive the w3220 chip found on iPAQ hx4700.
1893
1894           This driver is also available as a module ( = code which can be
1895           inserted and removed from the running kernel whenever you want). The
1896           module will be called w100fb. If you want to compile it as a module,
1897           say M here and read <file:Documentation/kbuild/modules.txt>.
1898
1899           If unsure, say N.
1900
1901 config SH_MIPI_DSI
1902         tristate
1903         depends on (SUPERH || ARCH_SHMOBILE) && HAVE_CLK
1904
1905 config SH_LCD_MIPI_DSI
1906         bool
1907
1908 config FB_SH_MOBILE_LCDC
1909         tristate "SuperH Mobile LCDC framebuffer support"
1910         depends on FB && (SUPERH || ARCH_SHMOBILE) && HAVE_CLK
1911         select FB_SYS_FILLRECT
1912         select FB_SYS_COPYAREA
1913         select FB_SYS_IMAGEBLIT
1914         select FB_SYS_FOPS
1915         select FB_DEFERRED_IO
1916         select SH_MIPI_DSI if SH_LCD_MIPI_DSI
1917         ---help---
1918           Frame buffer driver for the on-chip SH-Mobile LCD controller.
1919
1920 config FB_SH_MOBILE_HDMI
1921         tristate "SuperH Mobile HDMI controller support"
1922         depends on FB_SH_MOBILE_LCDC
1923         select FB_MODE_HELPERS
1924         select SOUND
1925         select SND
1926         select SND_SOC
1927         ---help---
1928           Driver for the on-chip SH-Mobile HDMI controller.
1929
1930 config FB_TMIO
1931         tristate "Toshiba Mobile IO FrameBuffer support"
1932         depends on FB && MFD_CORE
1933         select FB_CFB_FILLRECT
1934         select FB_CFB_COPYAREA
1935         select FB_CFB_IMAGEBLIT
1936         ---help---
1937           Frame buffer driver for the Toshiba Mobile IO integrated as found
1938           on the Sharp SL-6000 series
1939
1940           This driver is also available as a module ( = code which can be
1941           inserted and removed from the running kernel whenever you want). The
1942           module will be called tmiofb. If you want to compile it as a module,
1943           say M here and read <file:Documentation/kbuild/modules.txt>.
1944
1945           If unsure, say N.
1946
1947 config FB_TMIO_ACCELL
1948         bool "tmiofb acceleration"
1949         depends on FB_TMIO
1950         default y
1951
1952 config FB_S3C
1953         tristate "Samsung S3C framebuffer support"
1954         depends on FB && S3C_DEV_FB
1955         select FB_CFB_FILLRECT
1956         select FB_CFB_COPYAREA
1957         select FB_CFB_IMAGEBLIT
1958         ---help---
1959           Frame buffer driver for the built-in FB controller in the Samsung
1960           SoC line from the S3C2443 onwards, including the S3C2416, S3C2450,
1961           and the S3C64XX series such as the S3C6400 and S3C6410.
1962
1963           These chips all have the same basic framebuffer design with the
1964           actual capabilities depending on the chip. For instance the S3C6400
1965           and S3C6410 support 4 hardware windows whereas the S3C24XX series
1966           currently only have two.
1967
1968           Currently the support is only for the S3C6400 and S3C6410 SoCs.
1969
1970 config FB_S3C_DEBUG_REGWRITE
1971        bool "Debug register writes"
1972        depends on FB_S3C
1973        ---help---
1974          Show all register writes via printk(KERN_DEBUG)
1975
1976 config FB_S3C2410
1977         tristate "S3C2410 LCD framebuffer support"
1978         depends on FB && ARCH_S3C2410
1979         select FB_CFB_FILLRECT
1980         select FB_CFB_COPYAREA
1981         select FB_CFB_IMAGEBLIT
1982         ---help---
1983           Frame buffer driver for the built-in LCD controller in the Samsung
1984           S3C2410 processor.
1985
1986           This driver is also available as a module ( = code which can be
1987           inserted and removed from the running kernel whenever you want). The
1988           module will be called s3c2410fb. If you want to compile it as a module,
1989           say M here and read <file:Documentation/kbuild/modules.txt>.
1990
1991           If unsure, say N.
1992 config FB_S3C2410_DEBUG
1993         bool "S3C2410 lcd debug messages"
1994         depends on FB_S3C2410
1995         help
1996           Turn on debugging messages. Note that you can set/unset at run time
1997           through sysfs
1998
1999 config FB_NUC900
2000         bool "NUC900 LCD framebuffer support"
2001         depends on FB && ARCH_W90X900
2002         select FB_CFB_FILLRECT
2003         select FB_CFB_COPYAREA
2004         select FB_CFB_IMAGEBLIT
2005         ---help---
2006           Frame buffer driver for the built-in LCD controller in the Nuvoton
2007           NUC900 processor
2008
2009 config GPM1040A0_320X240
2010         bool "Giantplus Technology GPM1040A0 320x240 Color TFT LCD"
2011         depends on FB_NUC900
2012
2013 config FB_NUC900_DEBUG
2014         bool "NUC900 lcd debug messages"
2015         depends on FB_NUC900
2016         help
2017           Turn on debugging messages. Note that you can set/unset at run time
2018           through sysfs
2019
2020 config FB_SM501
2021         tristate "Silicon Motion SM501 framebuffer support"
2022         depends on FB && MFD_SM501
2023         select FB_CFB_FILLRECT
2024         select FB_CFB_COPYAREA
2025         select FB_CFB_IMAGEBLIT
2026         ---help---
2027           Frame buffer driver for the CRT and LCD controllers in the Silicon
2028           Motion SM501.
2029
2030           This driver is also available as a module ( = code which can be
2031           inserted and removed from the running kernel whenever you want). The
2032           module will be called sm501fb. If you want to compile it as a module,
2033           say M here and read <file:Documentation/kbuild/modules.txt>.
2034
2035           If unsure, say N.
2036
2037
2038 config FB_PNX4008_DUM
2039         tristate "Display Update Module support on Philips PNX4008 board"
2040         depends on FB && ARCH_PNX4008
2041         ---help---
2042           Say Y here to enable support for PNX4008 Display Update Module (DUM)
2043
2044 config FB_PNX4008_DUM_RGB
2045         tristate "RGB Framebuffer support on Philips PNX4008 board"
2046         depends on FB_PNX4008_DUM
2047         select FB_CFB_FILLRECT
2048         select FB_CFB_COPYAREA
2049         select FB_CFB_IMAGEBLIT
2050         ---help---
2051           Say Y here to enable support for PNX4008 RGB Framebuffer
2052
2053 config FB_IBM_GXT4500
2054         tristate "Framebuffer support for IBM GXT4500P adaptor"
2055         depends on FB && PPC
2056         select FB_CFB_FILLRECT
2057         select FB_CFB_COPYAREA
2058         select FB_CFB_IMAGEBLIT
2059         ---help---
2060           Say Y here to enable support for the IBM GXT4500P display
2061           adaptor, found on some IBM System P (pSeries) machines.
2062
2063 config FB_PS3
2064         tristate "PS3 GPU framebuffer driver"
2065         depends on FB && PS3_PS3AV
2066         select FB_SYS_FILLRECT
2067         select FB_SYS_COPYAREA
2068         select FB_SYS_IMAGEBLIT
2069         select FB_SYS_FOPS
2070         select VT_HW_CONSOLE_BINDING if FRAMEBUFFER_CONSOLE
2071         ---help---
2072           Include support for the virtual frame buffer in the PS3 platform.
2073
2074 config FB_PS3_DEFAULT_SIZE_M
2075         int "PS3 default frame buffer size (in MiB)"
2076         depends on FB_PS3
2077         default 9
2078         ---help---
2079           This is the default size (in MiB) of the virtual frame buffer in
2080           the PS3.
2081           The default value can be overridden on the kernel command line
2082           using the "ps3fb" option (e.g. "ps3fb=9M");
2083
2084 config FB_XILINX
2085         tristate "Xilinx frame buffer support"
2086         depends on FB && (XILINX_VIRTEX || MICROBLAZE)
2087         select FB_CFB_FILLRECT
2088         select FB_CFB_COPYAREA
2089         select FB_CFB_IMAGEBLIT
2090         ---help---
2091           Include support for the Xilinx ML300/ML403 reference design
2092           framebuffer. ML300 carries a 640*480 LCD display on the board,
2093           ML403 uses a standard DB15 VGA connector.
2094
2095 config FB_COBALT
2096         tristate "Cobalt server LCD frame buffer support"
2097         depends on FB && MIPS_COBALT
2098
2099 config FB_SH7760
2100         bool "SH7760/SH7763/SH7720/SH7721 LCDC support"
2101         depends on FB && (CPU_SUBTYPE_SH7760 || CPU_SUBTYPE_SH7763 \
2102                 || CPU_SUBTYPE_SH7720 || CPU_SUBTYPE_SH7721)
2103         select FB_CFB_FILLRECT
2104         select FB_CFB_COPYAREA
2105         select FB_CFB_IMAGEBLIT
2106         ---help---
2107           Support for the SH7760/SH7763/SH7720/SH7721 integrated
2108           (D)STN/TFT LCD Controller.
2109           Supports display resolutions up to 1024x1024 pixel, grayscale and
2110           color operation, with depths ranging from 1 bpp to 8 bpp monochrome
2111           and 8, 15 or 16 bpp color; 90 degrees clockwise display rotation for
2112           panels <= 320 pixel horizontal resolution.
2113
2114 config FB_DA8XX
2115         tristate "DA8xx/OMAP-L1xx Framebuffer support"
2116         depends on FB && ARCH_DAVINCI_DA8XX
2117         select FB_CFB_FILLRECT
2118         select FB_CFB_COPYAREA
2119         select FB_CFB_IMAGEBLIT
2120         ---help---
2121           This is the frame buffer device driver for the TI LCD controller
2122           found on DA8xx/OMAP-L1xx SoCs.
2123           If unsure, say N.
2124
2125 config FB_VIRTUAL
2126         tristate "Virtual Frame Buffer support (ONLY FOR TESTING!)"
2127         depends on FB
2128         select FB_SYS_FILLRECT
2129         select FB_SYS_COPYAREA
2130         select FB_SYS_IMAGEBLIT
2131         select FB_SYS_FOPS
2132         ---help---
2133           This is a `virtual' frame buffer device. It operates on a chunk of
2134           unswappable kernel memory instead of on the memory of a graphics
2135           board. This means you cannot see any output sent to this frame
2136           buffer device, while it does consume precious memory. The main use
2137           of this frame buffer device is testing and debugging the frame
2138           buffer subsystem. Do NOT enable it for normal systems! To protect
2139           the innocent, it has to be enabled explicitly at boot time using the
2140           kernel option `video=vfb:'.
2141
2142           To compile this driver as a module, choose M here: the
2143           module will be called vfb. In order to load it, you must use
2144           the vfb_enable=1 option.
2145
2146           If unsure, say N.
2147
2148 config XEN_FBDEV_FRONTEND
2149         tristate "Xen virtual frame buffer support"
2150         depends on FB && XEN
2151         select FB_SYS_FILLRECT
2152         select FB_SYS_COPYAREA
2153         select FB_SYS_IMAGEBLIT
2154         select FB_SYS_FOPS
2155         select FB_DEFERRED_IO
2156         select XEN_XENBUS_FRONTEND
2157         default y
2158         help
2159           This driver implements the front-end of the Xen virtual
2160           frame buffer driver.  It communicates with a back-end
2161           in another domain.
2162
2163 config FB_METRONOME
2164         tristate "E-Ink Metronome/8track controller support"
2165         depends on FB
2166         select FB_SYS_FILLRECT
2167         select FB_SYS_COPYAREA
2168         select FB_SYS_IMAGEBLIT
2169         select FB_SYS_FOPS
2170         select FB_DEFERRED_IO
2171         help
2172           This driver implements support for the E-Ink Metronome
2173           controller. The pre-release name for this device was 8track
2174           and could also have been called by some vendors as PVI-nnnn.
2175
2176 config FB_MB862XX
2177         tristate "Fujitsu MB862xx GDC support"
2178         depends on FB
2179         select FB_CFB_FILLRECT
2180         select FB_CFB_COPYAREA
2181         select FB_CFB_IMAGEBLIT
2182         ---help---
2183           Frame buffer driver for Fujitsu Carmine/Coral-P(A)/Lime controllers.
2184
2185 config FB_MB862XX_PCI_GDC
2186         bool "Carmine/Coral-P(A) GDC"
2187         depends on PCI && FB_MB862XX
2188         ---help---
2189           This enables framebuffer support for Fujitsu Carmine/Coral-P(A)
2190           PCI graphics controller devices.
2191
2192 config FB_MB862XX_LIME
2193         bool "Lime GDC"
2194         depends on FB_MB862XX
2195         depends on OF && !FB_MB862XX_PCI_GDC
2196         depends on PPC
2197         select FB_FOREIGN_ENDIAN
2198         select FB_LITTLE_ENDIAN
2199         ---help---
2200           Framebuffer support for Fujitsu Lime GDC on host CPU bus.
2201
2202 config FB_EP93XX
2203         tristate "EP93XX frame buffer support"
2204         depends on FB && ARCH_EP93XX
2205         select FB_CFB_FILLRECT
2206         select FB_CFB_COPYAREA
2207         select FB_CFB_IMAGEBLIT
2208         ---help---
2209           Framebuffer driver for the Cirrus Logic EP93XX series of processors.
2210           This driver is also available as a module. The module will be called
2211           ep93xx-fb.
2212
2213 config FB_PRE_INIT_FB
2214         bool "Don't reinitialize, use bootloader's GDC/Display configuration"
2215         depends on FB && FB_MB862XX_LIME
2216         ---help---
2217           Select this option if display contents should be inherited as set by
2218           the bootloader.
2219
2220 config FB_MSM
2221         tristate "MSM Framebuffer support"
2222         depends on FB && ARCH_MSM
2223         select FB_CFB_FILLRECT
2224         select FB_CFB_COPYAREA
2225         select FB_CFB_IMAGEBLIT
2226
2227 config FB_MX3
2228         tristate "MX3 Framebuffer support"
2229         depends on FB && MX3_IPU
2230         select FB_CFB_FILLRECT
2231         select FB_CFB_COPYAREA
2232         select FB_CFB_IMAGEBLIT
2233         default y
2234         help
2235           This is a framebuffer device for the i.MX31 LCD Controller. So
2236           far only synchronous displays are supported. If you plan to use
2237           an LCD display with your i.MX31 system, say Y here.
2238
2239 config FB_BROADSHEET
2240         tristate "E-Ink Broadsheet/Epson S1D13521 controller support"
2241         depends on FB
2242         select FB_SYS_FILLRECT
2243         select FB_SYS_COPYAREA
2244         select FB_SYS_IMAGEBLIT
2245         select FB_SYS_FOPS
2246         select FB_DEFERRED_IO
2247         help
2248           This driver implements support for the E-Ink Broadsheet
2249           controller. The release name for this device was Epson S1D13521
2250           and could also have been called by other names when coupled with
2251           a bridge adapter.
2252
2253 config FB_JZ4740
2254         tristate "JZ4740 LCD framebuffer support"
2255         depends on FB && MACH_JZ4740
2256         select FB_SYS_FILLRECT
2257         select FB_SYS_COPYAREA
2258         select FB_SYS_IMAGEBLIT
2259         help
2260           Framebuffer support for the JZ4740 SoC.
2261
2262 source "drivers/video/omap/Kconfig"
2263 source "drivers/video/omap2/Kconfig"
2264
2265 source "drivers/video/backlight/Kconfig"
2266 source "drivers/video/display/Kconfig"
2267
2268 if VT
2269         source "drivers/video/console/Kconfig"
2270 endif
2271
2272 if FB || SGI_NEWPORT_CONSOLE
2273         source "drivers/video/logo/Kconfig"
2274 endif
2275
2276 endmenu