5 tristate "OMAP2+ Display Subsystem support"
6 select VIDEOMODE_HELPERS
10 OMAP2+ Display Subsystem support.
14 config OMAP2_DSS_DEBUG
18 This enables printing of debug messages. Alternatively, debug messages
19 can also be enabled by setting CONFIG_DYNAMIC_DEBUG and then setting
20 appropriate flags in <debugfs>/dynamic_debug/control.
22 config OMAP2_DSS_DEBUGFS
23 bool "Debugfs filesystem support"
27 This enables debugfs for OMAPDSS at <debugfs>/omapdss. This enables
28 querying about clock configuration and register configuration of dss,
29 dispc, dsi, hdmi and rfbi.
31 config OMAP2_DSS_COLLECT_IRQ_STATS
32 bool "Collect DSS IRQ statistics"
33 depends on OMAP2_DSS_DEBUGFS
36 Collect DSS IRQ statistics, printable via debugfs.
38 The statistics can be found from
39 <debugfs>/omapdss/dispc_irq for DISPC interrupts, and
40 <debugfs>/omapdss/dsi_irq for DSI interrupts.
46 DPI Interface. This is the Parallel Display Interface.
53 MIPI DBI support (RFBI, Remote Framebuffer Interface, in Texas
54 Instrument's terminology).
56 DBI is a bus between the host processor and a peripheral,
57 such as a display or a framebuffer chip.
59 See http://www.mipi.org/ for DBI specifications.
65 OMAP Video Encoder support for S-Video and composite TV-out.
67 config OMAP2_DSS_HDMI_COMMON
71 bool "HDMI support for OMAP4"
73 select OMAP2_DSS_HDMI_COMMON
75 HDMI support for OMAP4 based SoCs.
77 config OMAP4_DSS_HDMI_AUDIO
81 bool "HDMI support for OMAP5"
83 select OMAP2_DSS_HDMI_COMMON
85 HDMI Interface for OMAP5 and similar cores. This adds the High
86 Definition Multimedia Interface. See http://www.hdmi.org/ for HDMI
89 config OMAP5_DSS_HDMI_AUDIO
90 depends on OMAP5_DSS_HDMI
97 SDI (Serial Display Interface) support.
99 SDI is a high speed one-way display serial bus between the host
100 processor and a display.
106 MIPI DSI (Display Serial Interface) support.
108 DSI is a high speed half-duplex serial interface between the host
109 processor and a peripheral, such as a display or a framebuffer chip.
111 See http://www.mipi.org/ for DSI specifications.
113 config OMAP2_DSS_MIN_FCK_PER_PCK
114 int "Minimum FCK/PCK ratio (for scaling)"
118 This can be used to adjust the minimum FCK/PCK ratio.
120 With this you can make sure that DISPC FCK is at least
121 n x PCK. Video plane scaling requires higher FCK than
124 If this is set to 0, there's no extra constraint on the
125 DISPC FCK. However, the FCK will at minimum be
126 2xPCK (if active matrix) or 3xPCK (if passive matrix).
128 Max FCK is 173MHz, so this doesn't work if your PCK
131 config OMAP2_DSS_SLEEP_AFTER_VENC_RESET
132 bool "Sleep 20ms after VENC reset"
135 There is a 20ms sleep after VENC reset which seemed to fix the
136 reset. The reason for the bug is unclear, and it's also unclear
137 on what platforms this happens.
139 This option enables the sleep, and is enabled by default. You can
140 disable the sleep if it doesn't cause problems on your platform.