1 #ifndef __LINUX_ATMEL_PWM_H
2 #define __LINUX_ATMEL_PWM_H
5 * struct pwm_channel - driver handle to a PWM channel
6 * @regs: base of this channel's registers
7 * @index: number of this channel (0..31)
8 * @mck: base clock rate, which can be prescaled and maybe subdivided
10 * Drivers initialize a pwm_channel structure using pwm_channel_alloc().
11 * Then they configure its clock rate (derived from MCK), alignment,
12 * polarity, and duty cycle by writing directly to the channel registers,
13 * before enabling the channel by calling pwm_channel_enable().
15 * After emitting a PWM signal for the desired length of time, drivers
16 * may then pwm_channel_disable() or pwm_channel_free(). Both of these
17 * disable the channel, but when it's freed the IRQ is deconfigured and
18 * the channel must later be re-allocated and reconfigured.
20 * Note that if the period or duty cycle need to be changed while the
21 * PWM channel is operating, drivers must use the PWM_CUPD double buffer
22 * mechanism, either polling until they change or getting implicitly
23 * notified through a once-per-period interrupt handler.
31 extern int pwm_channel_alloc(int index
, struct pwm_channel
*ch
);
32 extern int pwm_channel_free(struct pwm_channel
*ch
);
34 extern int pwm_clk_alloc(unsigned prescale
, unsigned div
);
35 extern void pwm_clk_free(unsigned clk
);
37 extern int __pwm_channel_onoff(struct pwm_channel
*ch
, int enabled
);
39 #define pwm_channel_enable(ch) __pwm_channel_onoff((ch), 1)
40 #define pwm_channel_disable(ch) __pwm_channel_onoff((ch), 0)
42 /* periodic interrupts, mostly for CUPD changes to period or cycle */
43 extern int pwm_channel_handler(struct pwm_channel
*ch
,
44 void (*handler
)(struct pwm_channel
*ch
));
46 /* per-channel registers (banked at pwm_channel->regs) */
47 #define PWM_CMR 0x00 /* mode register */
48 #define PWM_CPR_CPD (1 << 10) /* set: CUPD modifies period */
49 #define PWM_CPR_CPOL (1 << 9) /* set: idle high */
50 #define PWM_CPR_CALG (1 << 8) /* set: center align */
51 #define PWM_CPR_CPRE (0xf << 0) /* mask: rate is mck/(2^pre) */
52 #define PWM_CPR_CLKA (0xb << 0) /* rate CLKA */
53 #define PWM_CPR_CLKB (0xc << 0) /* rate CLKB */
54 #define PWM_CDTY 0x04 /* duty cycle (max of CPRD) */
55 #define PWM_CPRD 0x08 /* period (count up from zero) */
56 #define PWM_CCNT 0x0c /* counter (20 bits?) */
57 #define PWM_CUPD 0x10 /* update CPRD (or CDTY) next period */
60 pwm_channel_writel(struct pwm_channel
*pwmc
, unsigned offset
, u32 val
)
62 __raw_writel(val
, pwmc
->regs
+ offset
);
65 static inline u32
pwm_channel_readl(struct pwm_channel
*pwmc
, unsigned offset
)
67 return __raw_readl(pwmc
->regs
+ offset
);
70 #endif /* __LINUX_ATMEL_PWM_H */
This page took 0.031211 seconds and 5 git commands to generate.