5 * usr/include/linux/lp.h c.1991-1992 James Wiegand
6 * many modifications copyright (C) 1992 Michael K. Johnson
7 * Interrupt support added 1993 Nigel Gamble
8 * Removed 8255 status defines from inside __KERNEL__ Marcelo Tosatti
12 * Per POSIX guidelines, this module reserves the LP and lp prefixes
13 * These are the lp_table[minor].flags flags...
15 #define LP_EXIST 0x0001
16 #define LP_SELEC 0x0002
17 #define LP_BUSY 0x0004
18 #define LP_BUSY_BIT_POS 2
19 #define LP_OFFL 0x0008
20 #define LP_NOPA 0x0010
22 #define LP_ABORT 0x0040
23 #define LP_CAREFUL 0x0080 /* obsoleted -arca */
24 #define LP_ABORTOPEN 0x0100
26 #define LP_TRUST_IRQ_ 0x0200 /* obsolete */
27 #define LP_NO_REVERSE 0x0400 /* No reverse mode available. */
28 #define LP_DATA_AVAIL 0x0800 /* Data is available. */
31 * bit defines for 8255 status port
33 * accessed with LP_S(minor), which gets the byte...
35 #define LP_PBUSY 0x80 /* inverted input, active high */
36 #define LP_PACK 0x40 /* unchanged input, active low */
37 #define LP_POUTPA 0x20 /* unchanged input, active high */
38 #define LP_PSELECD 0x10 /* unchanged input, active high */
39 #define LP_PERRORP 0x08 /* unchanged input, active low */
41 /* timeout for each character. This is relative to bus cycles -- it
42 * is the count in a busy loop. THIS IS THE VALUE TO CHANGE if you
43 * have extremely slow printing, or if the machine seems to slow down
44 * a lot when you print. If you have slow printing, increase this
45 * number and recompile, and if your system gets bogged down, decrease
46 * this number. This can be changed with the tunelp(8) command as well.
49 #define LP_INIT_CHAR 1000
51 /* The parallel port specs apparently say that there needs to be
52 * a .5usec wait before and after the strobe.
55 #define LP_INIT_WAIT 1
57 /* This is the amount of time that the driver waits for the printer to
58 * catch up when the printer's buffer appears to be filled. If you
59 * want to tune this and have a fast printer (i.e. HPIIIP), decrease
60 * this number, and if you have a slow printer, increase this number.
61 * This is in hundredths of a second, the default 2 being .05 second.
62 * Or use the tunelp(8) command, which is especially nice if you want
63 * change back and forth between character and graphics printing, which
64 * are wildly different...
67 #define LP_INIT_TIME 2
70 #define LPCHAR 0x0601 /* corresponds to LP_INIT_CHAR */
71 #define LPTIME 0x0602 /* corresponds to LP_INIT_TIME */
72 #define LPABORT 0x0604 /* call with TRUE arg to abort on error,
73 FALSE to retry. Default is retry. */
74 #define LPSETIRQ 0x0605 /* call with new IRQ number,
75 or 0 for polling (no IRQ) */
76 #define LPGETIRQ 0x0606 /* get the current IRQ number */
77 #define LPWAIT 0x0608 /* corresponds to LP_INIT_WAIT */
78 /* NOTE: LPCAREFUL is obsoleted and it' s always the default right now -arca */
79 #define LPCAREFUL 0x0609 /* call with TRUE arg to require out-of-paper, off-
80 line, and error indicators good on all writes,
81 FALSE to ignore them. Default is ignore. */
82 #define LPABORTOPEN 0x060a /* call with TRUE arg to abort open() on error,
83 FALSE to ignore error. Default is ignore. */
84 #define LPGETSTATUS 0x060b /* return LP_S(minor) */
85 #define LPRESET 0x060c /* reset printer */
87 #define LPGETSTATS 0x060d /* get statistics (struct lp_stats) */
89 #define LPGETFLAGS 0x060e /* get status flags */
90 #define LPSETTIMEOUT 0x060f /* set parport timeout */
92 /* timeout for printk'ing a timeout, in jiffies (100ths of a second).
93 This is also used for re-checking error conditions if LP_ABORT is
94 not set. This is the default behavior. */
96 #define LP_TIMEOUT_INTERRUPT (60 * HZ)
97 #define LP_TIMEOUT_POLLED (10 * HZ)
101 #include <linux/wait.h>
102 #include <linux/mutex.h>
104 /* Magic numbers for defining port-device mappings */
105 #define LP_PARPORT_UNSPEC -4
106 #define LP_PARPORT_AUTO -3
107 #define LP_PARPORT_OFF -2
108 #define LP_PARPORT_NONE -1
110 #define LP_F(minor) lp_table[(minor)].flags /* flags for busy, etc. */
111 #define LP_CHAR(minor) lp_table[(minor)].chars /* busy timeout */
112 #define LP_TIME(minor) lp_table[(minor)].time /* wait time */
113 #define LP_WAIT(minor) lp_table[(minor)].wait /* strobe wait */
114 #define LP_IRQ(minor) lp_table[(minor)].dev->port->irq /* interrupt # */
115 /* PARPORT_IRQ_NONE means polled */
117 #define LP_STAT(minor) lp_table[(minor)].stats /* statistics area */
119 #define LP_BUFFER_SIZE PAGE_SIZE
121 #define LP_BASE(x) lp_table[(x)].dev->port->base
126 unsigned long sleeps
;
128 unsigned int maxwait
;
129 unsigned int meanwait
;
135 struct pardevice
*dev
;
142 unsigned int lastcall
;
143 unsigned int runchars
;
144 struct lp_stats stats
;
146 wait_queue_head_t waitq
;
147 unsigned int last_error
;
148 struct mutex port_mutex
;
149 wait_queue_head_t dataq
;
151 unsigned int best_mode
;
152 unsigned int current_mode
;
157 * The following constants describe the various signals of the printer port
158 * hardware. Note that the hardware inverts some signals and that some
159 * signals are active low. An example is LP_STROBE, which must be programmed
160 * with 1 for being active and 0 for being inactive, because the strobe signal
161 * gets inverted, but it is also active low.
166 * defines for 8255 control port
168 * accessed with LP_C(minor)
170 #define LP_PINTEN 0x10 /* high to read data in or-ed with data out */
171 #define LP_PSELECP 0x08 /* inverted output, active low */
172 #define LP_PINITP 0x04 /* unchanged output, active low */
173 #define LP_PAUTOLF 0x02 /* inverted output, active low */
174 #define LP_PSTROBE 0x01 /* short high output on raising edge */
177 * the value written to ports to test existence. PC-style ports will
178 * return the value written. AT-style ports will return 0. so why not
179 * make them the same ?
181 #define LP_DUMMY 0x00
184 * This is the port delay time, in microseconds.
185 * It is used only in the lp_init() and lp_reset() routine.
This page took 0.033757 seconds and 5 git commands to generate.