2 * linux/mii.h: definitions for MII-compatible transceivers
3 * Originally drivers/net/sunhme.h.
5 * Copyright (C) 1996, 1999, 2001 David S. Miller (davem@redhat.com)
8 #ifndef __LINUX_MII_H__
9 #define __LINUX_MII_H__
11 #include <linux/types.h>
13 /* Generic MII registers. */
14 #define MII_BMCR 0x00 /* Basic mode control register */
15 #define MII_BMSR 0x01 /* Basic mode status register */
16 #define MII_PHYSID1 0x02 /* PHYS ID 1 */
17 #define MII_PHYSID2 0x03 /* PHYS ID 2 */
18 #define MII_ADVERTISE 0x04 /* Advertisement control reg */
19 #define MII_LPA 0x05 /* Link partner ability reg */
20 #define MII_EXPANSION 0x06 /* Expansion register */
21 #define MII_CTRL1000 0x09 /* 1000BASE-T control */
22 #define MII_STAT1000 0x0a /* 1000BASE-T status */
23 #define MII_ESTATUS 0x0f /* Extended Status */
24 #define MII_DCOUNTER 0x12 /* Disconnect counter */
25 #define MII_FCSCOUNTER 0x13 /* False carrier counter */
26 #define MII_NWAYTEST 0x14 /* N-way auto-neg test reg */
27 #define MII_RERRCOUNTER 0x15 /* Receive error counter */
28 #define MII_SREVISION 0x16 /* Silicon revision */
29 #define MII_RESV1 0x17 /* Reserved... */
30 #define MII_LBRERROR 0x18 /* Lpback, rx, bypass error */
31 #define MII_PHYADDR 0x19 /* PHY address */
32 #define MII_RESV2 0x1a /* Reserved... */
33 #define MII_TPISTATUS 0x1b /* TPI status for 10mbps */
34 #define MII_NCONFIG 0x1c /* Network interface config */
36 /* Basic mode control register. */
37 #define BMCR_RESV 0x003f /* Unused... */
38 #define BMCR_SPEED1000 0x0040 /* MSB of Speed (1000) */
39 #define BMCR_CTST 0x0080 /* Collision test */
40 #define BMCR_FULLDPLX 0x0100 /* Full duplex */
41 #define BMCR_ANRESTART 0x0200 /* Auto negotiation restart */
42 #define BMCR_ISOLATE 0x0400 /* Isolate data paths from MII */
43 #define BMCR_PDOWN 0x0800 /* Enable low power state */
44 #define BMCR_ANENABLE 0x1000 /* Enable auto negotiation */
45 #define BMCR_SPEED100 0x2000 /* Select 100Mbps */
46 #define BMCR_LOOPBACK 0x4000 /* TXD loopback bits */
47 #define BMCR_RESET 0x8000 /* Reset to default state */
49 /* Basic mode status register. */
50 #define BMSR_ERCAP 0x0001 /* Ext-reg capability */
51 #define BMSR_JCD 0x0002 /* Jabber detected */
52 #define BMSR_LSTATUS 0x0004 /* Link status */
53 #define BMSR_ANEGCAPABLE 0x0008 /* Able to do auto-negotiation */
54 #define BMSR_RFAULT 0x0010 /* Remote fault detected */
55 #define BMSR_ANEGCOMPLETE 0x0020 /* Auto-negotiation complete */
56 #define BMSR_RESV 0x00c0 /* Unused... */
57 #define BMSR_ESTATEN 0x0100 /* Extended Status in R15 */
58 #define BMSR_100HALF2 0x0200 /* Can do 100BASE-T2 HDX */
59 #define BMSR_100FULL2 0x0400 /* Can do 100BASE-T2 FDX */
60 #define BMSR_10HALF 0x0800 /* Can do 10mbps, half-duplex */
61 #define BMSR_10FULL 0x1000 /* Can do 10mbps, full-duplex */
62 #define BMSR_100HALF 0x2000 /* Can do 100mbps, half-duplex */
63 #define BMSR_100FULL 0x4000 /* Can do 100mbps, full-duplex */
64 #define BMSR_100BASE4 0x8000 /* Can do 100mbps, 4k packets */
66 /* Advertisement control register. */
67 #define ADVERTISE_SLCT 0x001f /* Selector bits */
68 #define ADVERTISE_CSMA 0x0001 /* Only selector supported */
69 #define ADVERTISE_10HALF 0x0020 /* Try for 10mbps half-duplex */
70 #define ADVERTISE_1000XFULL 0x0020 /* Try for 1000BASE-X full-duplex */
71 #define ADVERTISE_10FULL 0x0040 /* Try for 10mbps full-duplex */
72 #define ADVERTISE_1000XHALF 0x0040 /* Try for 1000BASE-X half-duplex */
73 #define ADVERTISE_100HALF 0x0080 /* Try for 100mbps half-duplex */
74 #define ADVERTISE_1000XPAUSE 0x0080 /* Try for 1000BASE-X pause */
75 #define ADVERTISE_100FULL 0x0100 /* Try for 100mbps full-duplex */
76 #define ADVERTISE_1000XPSE_ASYM 0x0100 /* Try for 1000BASE-X asym pause */
77 #define ADVERTISE_100BASE4 0x0200 /* Try for 100mbps 4k packets */
78 #define ADVERTISE_PAUSE_CAP 0x0400 /* Try for pause */
79 #define ADVERTISE_PAUSE_ASYM 0x0800 /* Try for asymetric pause */
80 #define ADVERTISE_RESV 0x1000 /* Unused... */
81 #define ADVERTISE_RFAULT 0x2000 /* Say we can detect faults */
82 #define ADVERTISE_LPACK 0x4000 /* Ack link partners response */
83 #define ADVERTISE_NPAGE 0x8000 /* Next page bit */
85 #define ADVERTISE_FULL (ADVERTISE_100FULL | ADVERTISE_10FULL | \
87 #define ADVERTISE_ALL (ADVERTISE_10HALF | ADVERTISE_10FULL | \
88 ADVERTISE_100HALF | ADVERTISE_100FULL)
90 /* Link partner ability register. */
91 #define LPA_SLCT 0x001f /* Same as advertise selector */
92 #define LPA_10HALF 0x0020 /* Can do 10mbps half-duplex */
93 #define LPA_1000XFULL 0x0020 /* Can do 1000BASE-X full-duplex */
94 #define LPA_10FULL 0x0040 /* Can do 10mbps full-duplex */
95 #define LPA_1000XHALF 0x0040 /* Can do 1000BASE-X half-duplex */
96 #define LPA_100HALF 0x0080 /* Can do 100mbps half-duplex */
97 #define LPA_1000XPAUSE 0x0080 /* Can do 1000BASE-X pause */
98 #define LPA_100FULL 0x0100 /* Can do 100mbps full-duplex */
99 #define LPA_1000XPAUSE_ASYM 0x0100 /* Can do 1000BASE-X pause asym*/
100 #define LPA_100BASE4 0x0200 /* Can do 100mbps 4k packets */
101 #define LPA_PAUSE_CAP 0x0400 /* Can pause */
102 #define LPA_PAUSE_ASYM 0x0800 /* Can pause asymetrically */
103 #define LPA_RESV 0x1000 /* Unused... */
104 #define LPA_RFAULT 0x2000 /* Link partner faulted */
105 #define LPA_LPACK 0x4000 /* Link partner acked us */
106 #define LPA_NPAGE 0x8000 /* Next page bit */
108 #define LPA_DUPLEX (LPA_10FULL | LPA_100FULL)
109 #define LPA_100 (LPA_100FULL | LPA_100HALF | LPA_100BASE4)
111 /* Expansion register for auto-negotiation. */
112 #define EXPANSION_NWAY 0x0001 /* Can do N-way auto-nego */
113 #define EXPANSION_LCWP 0x0002 /* Got new RX page code word */
114 #define EXPANSION_ENABLENPAGE 0x0004 /* This enables npage words */
115 #define EXPANSION_NPCAPABLE 0x0008 /* Link partner supports npage */
116 #define EXPANSION_MFAULTS 0x0010 /* Multiple faults detected */
117 #define EXPANSION_RESV 0xffe0 /* Unused... */
119 #define ESTATUS_1000_TFULL 0x2000 /* Can do 1000BT Full */
120 #define ESTATUS_1000_THALF 0x1000 /* Can do 1000BT Half */
122 /* N-way test register. */
123 #define NWAYTEST_RESV1 0x00ff /* Unused... */
124 #define NWAYTEST_LOOPBACK 0x0100 /* Enable loopback for N-way */
125 #define NWAYTEST_RESV2 0xfe00 /* Unused... */
127 /* 1000BASE-T Control register */
128 #define ADVERTISE_1000FULL 0x0200 /* Advertise 1000BASE-T full duplex */
129 #define ADVERTISE_1000HALF 0x0100 /* Advertise 1000BASE-T half duplex */
130 #define CTL1000_AS_MASTER 0x0800
131 #define CTL1000_ENABLE_MASTER 0x1000
133 /* 1000BASE-T Status register */
134 #define LPA_1000LOCALRXOK 0x2000 /* Link partner local receiver status */
135 #define LPA_1000REMRXOK 0x1000 /* Link partner remote receiver status */
136 #define LPA_1000FULL 0x0800 /* Link partner 1000BASE-T full duplex */
137 #define LPA_1000HALF 0x0400 /* Link partner 1000BASE-T half duplex */
139 /* Flow control flags */
140 #define FLOW_CTRL_TX 0x01
141 #define FLOW_CTRL_RX 0x02
143 /* This structure is used in all SIOCxMIIxxx ioctl calls */
144 struct mii_ioctl_data
{
153 #include <linux/if.h>
163 unsigned int full_duplex
: 1; /* is full duplex? */
164 unsigned int force_media
: 1; /* is autoneg. disabled? */
165 unsigned int supports_gmii
: 1; /* are GMII registers supported? */
167 struct net_device
*dev
;
168 int (*mdio_read
) (struct net_device
*dev
, int phy_id
, int location
);
169 void (*mdio_write
) (struct net_device
*dev
, int phy_id
, int location
, int val
);
172 extern int mii_link_ok (struct mii_if_info
*mii
);
173 extern int mii_nway_restart (struct mii_if_info
*mii
);
174 extern int mii_ethtool_gset(struct mii_if_info
*mii
, struct ethtool_cmd
*ecmd
);
175 extern int mii_ethtool_sset(struct mii_if_info
*mii
, struct ethtool_cmd
*ecmd
);
176 extern int mii_check_gmii_support(struct mii_if_info
*mii
);
177 extern void mii_check_link (struct mii_if_info
*mii
);
178 extern unsigned int mii_check_media (struct mii_if_info
*mii
,
179 unsigned int ok_to_print
,
180 unsigned int init_media
);
181 extern int generic_mii_ioctl(struct mii_if_info
*mii_if
,
182 struct mii_ioctl_data
*mii_data
, int cmd
,
183 unsigned int *duplex_changed
);
186 static inline struct mii_ioctl_data
*if_mii(struct ifreq
*rq
)
188 return (struct mii_ioctl_data
*) &rq
->ifr_ifru
;
193 * @negotiated: value of MII ANAR and'd with ANLPAR
195 * Given a set of MII abilities, check each bit and returns the
196 * currently supported media, in the priority order defined by
197 * IEEE 802.3u. We use LPA_xxx constants but note this is not the
198 * value of LPA solely, as described above.
200 * The one exception to IEEE 802.3u is that 100baseT4 is placed
201 * between 100T-full and 100T-half. If your phy does not support
202 * 100T4 this is fine. If your phy places 100T4 elsewhere in the
203 * priority order, you will need to roll your own function.
205 static inline unsigned int mii_nway_result (unsigned int negotiated
)
209 if (negotiated
& LPA_100FULL
)
211 else if (negotiated
& LPA_100BASE4
)
213 else if (negotiated
& LPA_100HALF
)
215 else if (negotiated
& LPA_10FULL
)
225 * @duplex_lock: Non-zero if duplex is locked at full
226 * @negotiated: value of MII ANAR and'd with ANLPAR
228 * A small helper function for a common case. Returns one
229 * if the media is operating or locked at full duplex, and
230 * returns zero otherwise.
232 static inline unsigned int mii_duplex (unsigned int duplex_lock
,
233 unsigned int negotiated
)
237 if (mii_nway_result(negotiated
) & LPA_DUPLEX
)
243 * mii_advertise_flowctrl - get flow control advertisement flags
244 * @cap: Flow control capabilities (FLOW_CTRL_RX, FLOW_CTRL_TX or both)
246 static inline u16
mii_advertise_flowctrl(int cap
)
250 if (cap
& FLOW_CTRL_RX
)
251 adv
= ADVERTISE_PAUSE_CAP
| ADVERTISE_PAUSE_ASYM
;
252 if (cap
& FLOW_CTRL_TX
)
253 adv
^= ADVERTISE_PAUSE_ASYM
;
259 * mii_resolve_flowctrl_fdx
260 * @lcladv: value of MII ADVERTISE register
261 * @rmtadv: value of MII LPA register
263 * Resolve full duplex flow control as per IEEE 802.3-2005 table 28B-3
265 static inline u8
mii_resolve_flowctrl_fdx(u16 lcladv
, u16 rmtadv
)
269 if (lcladv
& rmtadv
& ADVERTISE_PAUSE_CAP
) {
270 cap
= FLOW_CTRL_TX
| FLOW_CTRL_RX
;
271 } else if (lcladv
& rmtadv
& ADVERTISE_PAUSE_ASYM
) {
272 if (lcladv
& ADVERTISE_PAUSE_CAP
)
274 else if (rmtadv
& ADVERTISE_PAUSE_CAP
)
281 #endif /* __KERNEL__ */
282 #endif /* __LINUX_MII_H__ */
This page took 0.035962 seconds and 5 git commands to generate.