include/linux/mmc/host.h

   1 /*
   2  *  linux/include/linux/mmc/host.h
   3  *
   4  * This program is free software; you can redistribute it and/or modify
   5  * it under the terms of the GNU General Public License version 2 as
   6  * published by the Free Software Foundation.
   7  *
   8  *  Host driver specific definitions.
   9  */
  10 #ifndef LINUX_MMC_HOST_H
  11 #define LINUX_MMC_HOST_H
  12
  13 #include <linux/leds.h>
  14 #include <linux/sched.h>
  15 #include <linux/fault-inject.h>
  16
  17 #include <linux/mmc/core.h>
  18 #include <linux/mmc/pm.h>
  19
  20 struct mmc_ios {
  21         unsigned int    clock;                  /* clock rate */
  22         unsigned short  vdd;
  23
  24 /* vdd stores the bit number of the selected voltage range from below. */
  25
  26         unsigned char   bus_mode;               /* command output mode */
  27
  28 #define MMC_BUSMODE_OPENDRAIN   1
  29 #define MMC_BUSMODE_PUSHPULL    2
  30
  31         unsigned char   chip_select;            /* SPI chip select */
  32
  33 #define MMC_CS_DONTCARE         0
  34 #define MMC_CS_HIGH             1
  35 #define MMC_CS_LOW              2
  36
  37         unsigned char   power_mode;             /* power supply mode */
  38
  39 #define MMC_POWER_OFF           0
  40 #define MMC_POWER_UP            1
  41 #define MMC_POWER_ON            2
  42
  43         unsigned char   bus_width;              /* data bus width */
  44
  45 #define MMC_BUS_WIDTH_1         0
  46 #define MMC_BUS_WIDTH_4         2
  47 #define MMC_BUS_WIDTH_8         3
  48
  49         unsigned char   timing;                 /* timing specification used */
  50
  51 #define MMC_TIMING_LEGACY       0
  52 #define MMC_TIMING_MMC_HS       1
  53 #define MMC_TIMING_SD_HS        2
  54 #define MMC_TIMING_UHS_SDR12    MMC_TIMING_LEGACY
  55 #define MMC_TIMING_UHS_SDR25    MMC_TIMING_SD_HS
  56 #define MMC_TIMING_UHS_SDR50    3
  57 #define MMC_TIMING_UHS_SDR104   4
  58 #define MMC_TIMING_UHS_DDR50    5
  59 #define MMC_TIMING_MMC_HS200    6
  60
  61 #define MMC_SDR_MODE            0
  62 #define MMC_1_2V_DDR_MODE       1
  63 #define MMC_1_8V_DDR_MODE       2
  64 #define MMC_1_2V_SDR_MODE       3
  65 #define MMC_1_8V_SDR_MODE       4
  66
  67         unsigned char   signal_voltage;         /* signalling voltage (1.8V or 3.3V) */
  68
  69 #define MMC_SIGNAL_VOLTAGE_330  0
  70 #define MMC_SIGNAL_VOLTAGE_180  1
  71 #define MMC_SIGNAL_VOLTAGE_120  2
  72
  73         unsigned char   drv_type;               /* driver type (A, B, C, D) */
  74
  75 #define MMC_SET_DRIVER_TYPE_B   0
  76 #define MMC_SET_DRIVER_TYPE_A   1
  77 #define MMC_SET_DRIVER_TYPE_C   2
  78 #define MMC_SET_DRIVER_TYPE_D   3
  79 };
  80
  81 struct mmc_host_ops {
  82         /*
  83          * Hosts that support power saving can use the 'enable' and 'disable'
  84          * methods to exit and enter power saving states. 'enable' is called
  85          * when the host is claimed and 'disable' is called (or scheduled with
  86          * a delay) when the host is released. The 'disable' is scheduled if
  87          * the disable delay set by 'mmc_set_disable_delay()' is non-zero,
  88          * otherwise 'disable' is called immediately. 'disable' may be
  89          * scheduled repeatedly, to permit ever greater power saving at the
  90          * expense of ever greater latency to re-enable. Rescheduling is
  91          * determined by the return value of the 'disable' method. A positive
  92          * value gives the delay in milliseconds.
  93          *
  94          * In the case where a host function (like set_ios) may be called
  95          * with or without the host claimed, enabling and disabling can be
  96          * done directly and will nest correctly. Call 'mmc_host_enable()' and
  97          * 'mmc_host_lazy_disable()' for this purpose, but note that these
  98          * functions must be paired.
  99          *
 100          * Alternatively, 'mmc_host_enable()' may be paired with
 101          * 'mmc_host_disable()' which calls 'disable' immediately.  In this
 102          * case the 'disable' method will be called with 'lazy' set to 0.
 103          * This is mainly useful for error paths.
 104          *
 105          * Because lazy disable may be called from a work queue, the 'disable'
 106          * method must claim the host when 'lazy' != 0, which will work
 107          * correctly because recursion is detected and handled.
 108          */
 109         int (*enable)(struct mmc_host *host);
 110         int (*disable)(struct mmc_host *host, int lazy);
 111         /*
 112          * It is optional for the host to implement pre_req and post_req in
 113          * order to support double buffering of requests (prepare one
 114          * request while another request is active).
 115          * pre_req() must always be followed by a post_req().
 116          * To undo a call made to pre_req(), call post_req() with
 117          * a nonzero err condition.
 118          */
 119         void    (*post_req)(struct mmc_host *host, struct mmc_request *req,
 120                             int err);
 121         void    (*pre_req)(struct mmc_host *host, struct mmc_request *req,
 122                            bool is_first_req);
 123         void    (*request)(struct mmc_host *host, struct mmc_request *req);
 124         /*
 125          * Avoid calling these three functions too often or in a "fast path",
 126          * since underlaying controller might implement them in an expensive
 127          * and/or slow way.
 128          *
 129          * Also note that these functions might sleep, so don't call them
 130          * in the atomic contexts!
 131          *
 132          * Return values for the get_ro callback should be:
 133          *   0 for a read/write card
 134          *   1 for a read-only card
 135          *   -ENOSYS when not supported (equal to NULL callback)
 136          *   or a negative errno value when something bad happened
 137          *
 138          * Return values for the get_cd callback should be:
 139          *   0 for a absent card
 140          *   1 for a present card
 141          *   -ENOSYS when not supported (equal to NULL callback)
 142          *   or a negative errno value when something bad happened
 143          */
 144         void    (*set_ios)(struct mmc_host *host, struct mmc_ios *ios);
 145         int     (*get_ro)(struct mmc_host *host);
 146         int     (*get_cd)(struct mmc_host *host);
 147
 148         void    (*enable_sdio_irq)(struct mmc_host *host, int enable);
 149
 150         /* optional callback for HC quirks */
 151         void    (*init_card)(struct mmc_host *host, struct mmc_card *card);
 152
 153         int     (*start_signal_voltage_switch)(struct mmc_host *host, struct mmc_ios *ios);
 154
 155         /* The tuning command opcode value is different for SD and eMMC cards */
 156         int     (*execute_tuning)(struct mmc_host *host, u32 opcode);
 157         void    (*enable_preset_value)(struct mmc_host *host, bool enable);
 158         int     (*select_drive_strength)(unsigned int max_dtr, int host_drv, int card_drv);
 159         void    (*hw_reset)(struct mmc_host *host);
 160 };
 161
 162 struct mmc_card;
 163 struct device;
 164
 165 struct mmc_async_req {
 166         /* active mmc request */
 167         struct mmc_request      *mrq;
 168         /*
 169          * Check error status of completed mmc request.
 170          * Returns 0 if success otherwise non zero.
 171          */
 172         int (*err_check) (struct mmc_card *, struct mmc_async_req *);
 173 };
 174
 175 struct mmc_hotplug {
 176         unsigned int irq;
 177         void *handler_priv;
 178 };
 179
 180 struct mmc_host {
 181         struct device           *parent;
 182         struct device           class_dev;
 183         int                     index;
 184         const struct mmc_host_ops *ops;
 185         unsigned int            f_min;
 186         unsigned int            f_max;
 187         unsigned int            f_init;
 188         u32                     ocr_avail;
 189         u32                     ocr_avail_sdio; /* SDIO-specific OCR */
 190         u32                     ocr_avail_sd;   /* SD-specific OCR */
 191         u32                     ocr_avail_mmc;  /* MMC-specific OCR */
 192         struct notifier_block   pm_notify;
 193
 194 #define MMC_VDD_165_195         0x00000080      /* VDD voltage 1.65 - 1.95 */
 195 #define MMC_VDD_20_21           0x00000100      /* VDD voltage 2.0 ~ 2.1 */
 196 #define MMC_VDD_21_22           0x00000200      /* VDD voltage 2.1 ~ 2.2 */
 197 #define MMC_VDD_22_23           0x00000400      /* VDD voltage 2.2 ~ 2.3 */
 198 #define MMC_VDD_23_24           0x00000800      /* VDD voltage 2.3 ~ 2.4 */
 199 #define MMC_VDD_24_25           0x00001000      /* VDD voltage 2.4 ~ 2.5 */
 200 #define MMC_VDD_25_26           0x00002000      /* VDD voltage 2.5 ~ 2.6 */
 201 #define MMC_VDD_26_27           0x00004000      /* VDD voltage 2.6 ~ 2.7 */
 202 #define MMC_VDD_27_28           0x00008000      /* VDD voltage 2.7 ~ 2.8 */
 203 #define MMC_VDD_28_29           0x00010000      /* VDD voltage 2.8 ~ 2.9 */
 204 #define MMC_VDD_29_30           0x00020000      /* VDD voltage 2.9 ~ 3.0 */
 205 #define MMC_VDD_30_31           0x00040000      /* VDD voltage 3.0 ~ 3.1 */
 206 #define MMC_VDD_31_32           0x00080000      /* VDD voltage 3.1 ~ 3.2 */
 207 #define MMC_VDD_32_33           0x00100000      /* VDD voltage 3.2 ~ 3.3 */
 208 #define MMC_VDD_33_34           0x00200000      /* VDD voltage 3.3 ~ 3.4 */
 209 #define MMC_VDD_34_35           0x00400000      /* VDD voltage 3.4 ~ 3.5 */
 210 #define MMC_VDD_35_36           0x00800000      /* VDD voltage 3.5 ~ 3.6 */
 211
 212         unsigned long           caps;           /* Host capabilities */
 213
 214 #define MMC_CAP_4_BIT_DATA      (1 << 0)        /* Can the host do 4 bit transfers */
 215 #define MMC_CAP_MMC_HIGHSPEED   (1 << 1)        /* Can do MMC high-speed timing */
 216 #define MMC_CAP_SD_HIGHSPEED    (1 << 2)        /* Can do SD high-speed timing */
 217 #define MMC_CAP_SDIO_IRQ        (1 << 3)        /* Can signal pending SDIO IRQs */
 218 #define MMC_CAP_SPI             (1 << 4)        /* Talks only SPI protocols */
 219 #define MMC_CAP_NEEDS_POLL      (1 << 5)        /* Needs polling for card-detection */
 220 #define MMC_CAP_8_BIT_DATA      (1 << 6)        /* Can the host do 8 bit transfers */
 221 #define MMC_CAP_DISABLE         (1 << 7)        /* Can the host be disabled */
 222 #define MMC_CAP_NONREMOVABLE    (1 << 8)        /* Nonremovable e.g. eMMC */
 223 #define MMC_CAP_WAIT_WHILE_BUSY (1 << 9)        /* Waits while card is busy */
 224 #define MMC_CAP_ERASE           (1 << 10)       /* Allow erase/trim commands */
 225 #define MMC_CAP_1_8V_DDR        (1 << 11)       /* can support */
 226                                                 /* DDR mode at 1.8V */
 227 #define MMC_CAP_1_2V_DDR        (1 << 12)       /* can support */
 228                                                 /* DDR mode at 1.2V */
 229 #define MMC_CAP_POWER_OFF_CARD  (1 << 13)       /* Can power off after boot */
 230 #define MMC_CAP_BUS_WIDTH_TEST  (1 << 14)       /* CMD14/CMD19 bus width ok */
 231 #define MMC_CAP_UHS_SDR12       (1 << 15)       /* Host supports UHS SDR12 mode */
 232 #define MMC_CAP_UHS_SDR25       (1 << 16)       /* Host supports UHS SDR25 mode */
 233 #define MMC_CAP_UHS_SDR50       (1 << 17)       /* Host supports UHS SDR50 mode */
 234 #define MMC_CAP_UHS_SDR104      (1 << 18)       /* Host supports UHS SDR104 mode */
 235 #define MMC_CAP_UHS_DDR50       (1 << 19)       /* Host supports UHS DDR50 mode */
 236 #define MMC_CAP_SET_XPC_330     (1 << 20)       /* Host supports >150mA current at 3.3V */
 237 #define MMC_CAP_SET_XPC_300     (1 << 21)       /* Host supports >150mA current at 3.0V */
 238 #define MMC_CAP_SET_XPC_180     (1 << 22)       /* Host supports >150mA current at 1.8V */
 239 #define MMC_CAP_DRIVER_TYPE_A   (1 << 23)       /* Host supports Driver Type A */
 240 #define MMC_CAP_DRIVER_TYPE_C   (1 << 24)       /* Host supports Driver Type C */
 241 #define MMC_CAP_DRIVER_TYPE_D   (1 << 25)       /* Host supports Driver Type D */
 242 #define MMC_CAP_MAX_CURRENT_200 (1 << 26)       /* Host max current limit is 200mA */
 243 #define MMC_CAP_MAX_CURRENT_400 (1 << 27)       /* Host max current limit is 400mA */
 244 #define MMC_CAP_MAX_CURRENT_600 (1 << 28)       /* Host max current limit is 600mA */
 245 #define MMC_CAP_MAX_CURRENT_800 (1 << 29)       /* Host max current limit is 800mA */
 246 #define MMC_CAP_CMD23           (1 << 30)       /* CMD23 supported. */
 247 #define MMC_CAP_HW_RESET        (1 << 31)       /* Hardware reset */
 248
 249         unsigned int            caps2;          /* More host capabilities */
 250
 251 #define MMC_CAP2_BOOTPART_NOACC (1 << 0)        /* Boot partition no access */
 252 #define MMC_CAP2_CACHE_CTRL     (1 << 1)        /* Allow cache control */
 253 #define MMC_CAP2_POWEROFF_NOTIFY (1 << 2)       /* Notify poweroff supported */
 254 #define MMC_CAP2_NO_MULTI_READ  (1 << 3)        /* Multiblock reads don't work */
 255 #define MMC_CAP2_NO_SLEEP_CMD   (1 << 4)        /* Don't allow sleep command */
 256 #define MMC_CAP2_HS200_1_8V_SDR (1 << 5)        /* can support */
 257 #define MMC_CAP2_HS200_1_2V_SDR (1 << 6)        /* can support */
 258 #define MMC_CAP2_HS200          (MMC_CAP2_HS200_1_8V_SDR | \
 259                                  MMC_CAP2_HS200_1_2V_SDR)
 260
 261         mmc_pm_flag_t           pm_caps;        /* supported pm features */
 262         unsigned int        power_notify_type;
 263 #define MMC_HOST_PW_NOTIFY_NONE         0
 264 #define MMC_HOST_PW_NOTIFY_SHORT        1
 265 #define MMC_HOST_PW_NOTIFY_LONG         2
 266
 267 #ifdef CONFIG_MMC_CLKGATE
 268         int                     clk_requests;   /* internal reference counter */
 269         unsigned int            clk_delay;      /* number of MCI clk hold cycles */
 270         bool                    clk_gated;      /* clock gated */
 271         struct delayed_work     clk_gate_work; /* delayed clock gate */
 272         unsigned int            clk_old;        /* old clock value cache */
 273         spinlock_t              clk_lock;       /* lock for clk fields */
 274         struct mutex            clk_gate_mutex; /* mutex for clock gating */
 275         struct device_attribute clkgate_delay_attr;
 276         unsigned long           clkgate_delay;
 277 #endif
 278
 279         /* host specific block data */
 280         unsigned int            max_seg_size;   /* see blk_queue_max_segment_size */
 281         unsigned short          max_segs;       /* see blk_queue_max_segments */
 282         unsigned short          unused;
 283         unsigned int            max_req_size;   /* maximum number of bytes in one req */
 284         unsigned int            max_blk_size;   /* maximum size of one mmc block */
 285         unsigned int            max_blk_count;  /* maximum number of blocks in one req */
 286         unsigned int            max_discard_to; /* max. discard timeout in ms */
 287
 288         /* private data */
 289         spinlock_t              lock;           /* lock for claim and bus ops */
 290
 291         struct mmc_ios          ios;            /* current io bus settings */
 292         u32                     ocr;            /* the current OCR setting */
 293
 294         /* group bitfields together to minimize padding */
 295         unsigned int            use_spi_crc:1;
 296         unsigned int            claimed:1;      /* host exclusively claimed */
 297         unsigned int            bus_dead:1;     /* bus has been released */
 298 #ifdef CONFIG_MMC_DEBUG
 299         unsigned int            removed:1;      /* host is being removed */
 300 #endif
 301
 302         /* Only used with MMC_CAP_DISABLE */
 303         int                     enabled;        /* host is enabled */
 304         int                     rescan_disable; /* disable card detection */
 305         int                     nesting_cnt;    /* "enable" nesting count */
 306         int                     en_dis_recurs;  /* detect recursion */
 307         unsigned int            disable_delay;  /* disable delay in msecs */
 308         struct delayed_work     disable;        /* disabling work */
 309
 310         struct mmc_card         *card;          /* device attached to this host */
 311
 312         wait_queue_head_t       wq;
 313         struct task_struct      *claimer;       /* task that has host claimed */
 314         int                     claim_cnt;      /* "claim" nesting count */
 315
 316         struct delayed_work     detect;
 317         int                     detect_change;  /* card detect flag */
 318         struct mmc_hotplug      hotplug;
 319
 320         const struct mmc_bus_ops *bus_ops;      /* current bus driver */
 321         unsigned int            bus_refs;       /* reference counter */
 322
 323         unsigned int            sdio_irqs;
 324         struct task_struct      *sdio_irq_thread;
 325         atomic_t                sdio_irq_thread_abort;
 326
 327         mmc_pm_flag_t           pm_flags;       /* requested pm features */
 328
 329 #ifdef CONFIG_LEDS_TRIGGERS
 330         struct led_trigger      *led;           /* activity led */
 331 #endif
 332
 333 #ifdef CONFIG_REGULATOR
 334         bool                    regulator_enabled; /* regulator state */
 335 #endif
 336
 337         struct dentry           *debugfs_root;
 338
 339         struct mmc_async_req    *areq;          /* active async req */
 340
 341 #ifdef CONFIG_FAIL_MMC_REQUEST
 342         struct fault_attr       fail_mmc_request;
 343 #endif
 344
 345         unsigned int            actual_clock;   /* Actual HC clock rate */
 346
 347         unsigned long           private[0] ____cacheline_aligned;
 348 };
 349
 350 extern struct mmc_host *mmc_alloc_host(int extra, struct device *);
 351 extern int mmc_add_host(struct mmc_host *);
 352 extern void mmc_remove_host(struct mmc_host *);
 353 extern void mmc_free_host(struct mmc_host *);
 354
 355 static inline void *mmc_priv(struct mmc_host *host)
 356 {
 357         return (void *)host->private;
 358 }
 359
 360 #define mmc_host_is_spi(host)   ((host)->caps & MMC_CAP_SPI)
 361
 362 #define mmc_dev(x)      ((x)->parent)
 363 #define mmc_classdev(x) (&(x)->class_dev)
 364 #define mmc_hostname(x) (dev_name(&(x)->class_dev))
 365
 366 extern int mmc_suspend_host(struct mmc_host *);
 367 extern int mmc_resume_host(struct mmc_host *);
 368
 369 extern int mmc_power_save_host(struct mmc_host *host);
 370 extern int mmc_power_restore_host(struct mmc_host *host);
 371
 372 extern void mmc_detect_change(struct mmc_host *, unsigned long delay);
 373 extern void mmc_request_done(struct mmc_host *, struct mmc_request *);
 374
 375 extern int mmc_cache_ctrl(struct mmc_host *, u8);
 376
 377 static inline void mmc_signal_sdio_irq(struct mmc_host *host)
 378 {
 379         host->ops->enable_sdio_irq(host, 0);
 380         wake_up_process(host->sdio_irq_thread);
 381 }
 382
 383 struct regulator;
 384
 385 #ifdef CONFIG_REGULATOR
 386 int mmc_regulator_get_ocrmask(struct regulator *supply);
 387 int mmc_regulator_set_ocr(struct mmc_host *mmc,
 388                         struct regulator *supply,
 389                         unsigned short vdd_bit);
 390 #else
 391 static inline int mmc_regulator_get_ocrmask(struct regulator *supply)
 392 {
 393         return 0;
 394 }
 395
 396 static inline int mmc_regulator_set_ocr(struct mmc_host *mmc,
 397                                  struct regulator *supply,
 398                                  unsigned short vdd_bit)
 399 {
 400         return 0;
 401 }
 402 #endif
 403
 404 int mmc_card_awake(struct mmc_host *host);
 405 int mmc_card_sleep(struct mmc_host *host);
 406 int mmc_card_can_sleep(struct mmc_host *host);
 407
 408 int mmc_host_enable(struct mmc_host *host);
 409 int mmc_host_disable(struct mmc_host *host);
 410 int mmc_host_lazy_disable(struct mmc_host *host);
 411 int mmc_pm_notify(struct notifier_block *notify_block, unsigned long, void *);
 412
 413 static inline void mmc_set_disable_delay(struct mmc_host *host,
 414                                          unsigned int disable_delay)
 415 {
 416         host->disable_delay = disable_delay;
 417 }
 418
 419 /* Module parameter */
 420 extern int mmc_assume_removable;
 421
 422 static inline int mmc_card_is_removable(struct mmc_host *host)
 423 {
 424         return !(host->caps & MMC_CAP_NONREMOVABLE) && mmc_assume_removable;
 425 }
 426
 427 static inline int mmc_card_keep_power(struct mmc_host *host)
 428 {
 429         return host->pm_flags & MMC_PM_KEEP_POWER;
 430 }
 431
 432 static inline int mmc_card_wake_sdio_irq(struct mmc_host *host)
 433 {
 434         return host->pm_flags & MMC_PM_WAKE_SDIO_IRQ;
 435 }
 436
 437 static inline int mmc_host_cmd23(struct mmc_host *host)
 438 {
 439         return host->caps & MMC_CAP_CMD23;
 440 }
 441
 442 static inline int mmc_boot_partition_access(struct mmc_host *host)
 443 {
 444         return !(host->caps2 & MMC_CAP2_BOOTPART_NOACC);
 445 }
 446
 447 #endif /* LINUX_MMC_HOST_H */