* your option) any later version.
*/
+#define pr_fmt(fmt) "ep93xx " KBUILD_MODNAME ": " fmt
+
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/interrupt.h>
#include <linux/dma-mapping.h>
#include <linux/timex.h>
+#include <linux/irq.h>
#include <linux/io.h>
#include <linux/gpio.h>
#include <linux/leds.h>
#include <asm/mach/map.h>
#include <asm/mach/time.h>
-#include <asm/mach/irq.h>
#include <asm/hardware/vic.h>
* to use this timer for something else. We also use timer 4 for keeping
* track of lost jiffies.
*/
-static unsigned int last_jiffy_time;
-
+#define EP93XX_TIMER_REG(x) (EP93XX_TIMER_BASE + (x))
+#define EP93XX_TIMER1_LOAD EP93XX_TIMER_REG(0x00)
+#define EP93XX_TIMER1_VALUE EP93XX_TIMER_REG(0x04)
+#define EP93XX_TIMER1_CONTROL EP93XX_TIMER_REG(0x08)
+#define EP93XX_TIMER123_CONTROL_ENABLE (1 << 7)
+#define EP93XX_TIMER123_CONTROL_MODE (1 << 6)
+#define EP93XX_TIMER123_CONTROL_CLKSEL (1 << 3)
+#define EP93XX_TIMER1_CLEAR EP93XX_TIMER_REG(0x0c)
+#define EP93XX_TIMER2_LOAD EP93XX_TIMER_REG(0x20)
+#define EP93XX_TIMER2_VALUE EP93XX_TIMER_REG(0x24)
+#define EP93XX_TIMER2_CONTROL EP93XX_TIMER_REG(0x28)
+#define EP93XX_TIMER2_CLEAR EP93XX_TIMER_REG(0x2c)
+#define EP93XX_TIMER4_VALUE_LOW EP93XX_TIMER_REG(0x60)
+#define EP93XX_TIMER4_VALUE_HIGH EP93XX_TIMER_REG(0x64)
+#define EP93XX_TIMER4_VALUE_HIGH_ENABLE (1 << 8)
+#define EP93XX_TIMER3_LOAD EP93XX_TIMER_REG(0x80)
+#define EP93XX_TIMER3_VALUE EP93XX_TIMER_REG(0x84)
+#define EP93XX_TIMER3_CONTROL EP93XX_TIMER_REG(0x88)
+#define EP93XX_TIMER3_CLEAR EP93XX_TIMER_REG(0x8c)
+
+#define EP93XX_TIMER123_CLOCK 508469
+#define EP93XX_TIMER4_CLOCK 983040
+
+#define TIMER1_RELOAD ((EP93XX_TIMER123_CLOCK / HZ) - 1)
#define TIMER4_TICKS_PER_JIFFY DIV_ROUND_CLOSEST(CLOCK_TICK_RATE, HZ)
+static unsigned int last_jiffy_time;
+
static irqreturn_t ep93xx_timer_interrupt(int irq, void *dev_id)
{
+ /* Writing any value clears the timer interrupt */
__raw_writel(1, EP93XX_TIMER1_CLEAR);
+
+ /* Recover lost jiffies */
while ((signed long)
(__raw_readl(EP93XX_TIMER4_VALUE_LOW) - last_jiffy_time)
>= TIMER4_TICKS_PER_JIFFY) {
static void __init ep93xx_timer_init(void)
{
+ u32 tmode = EP93XX_TIMER123_CONTROL_MODE |
+ EP93XX_TIMER123_CONTROL_CLKSEL;
+
/* Enable periodic HZ timer. */
- __raw_writel(0x48, EP93XX_TIMER1_CONTROL);
- __raw_writel((508469 / HZ) - 1, EP93XX_TIMER1_LOAD);
- __raw_writel(0xc8, EP93XX_TIMER1_CONTROL);
+ __raw_writel(tmode, EP93XX_TIMER1_CONTROL);
+ __raw_writel(TIMER1_RELOAD, EP93XX_TIMER1_LOAD);
+ __raw_writel(tmode | EP93XX_TIMER123_CONTROL_ENABLE,
+ EP93XX_TIMER1_CONTROL);
/* Enable lost jiffy timer. */
- __raw_writel(0x100, EP93XX_TIMER4_VALUE_HIGH);
+ __raw_writel(EP93XX_TIMER4_VALUE_HIGH_ENABLE,
+ EP93XX_TIMER4_VALUE_HIGH);
setup_irq(IRQ_EP93XX_TIMER1, &ep93xx_timer_irq);
}
};
-/*************************************************************************
- * GPIO handling for EP93xx
- *************************************************************************/
-static unsigned char gpio_int_unmasked[3];
-static unsigned char gpio_int_enabled[3];
-static unsigned char gpio_int_type1[3];
-static unsigned char gpio_int_type2[3];
-static unsigned char gpio_int_debounce[3];
-
-/* Port ordering is: A B F */
-static const u8 int_type1_register_offset[3] = { 0x90, 0xac, 0x4c };
-static const u8 int_type2_register_offset[3] = { 0x94, 0xb0, 0x50 };
-static const u8 eoi_register_offset[3] = { 0x98, 0xb4, 0x54 };
-static const u8 int_en_register_offset[3] = { 0x9c, 0xb8, 0x58 };
-static const u8 int_debounce_register_offset[3] = { 0xa8, 0xc4, 0x64 };
-
-void ep93xx_gpio_update_int_params(unsigned port)
-{
- BUG_ON(port > 2);
-
- __raw_writeb(0, EP93XX_GPIO_REG(int_en_register_offset[port]));
-
- __raw_writeb(gpio_int_type2[port],
- EP93XX_GPIO_REG(int_type2_register_offset[port]));
-
- __raw_writeb(gpio_int_type1[port],
- EP93XX_GPIO_REG(int_type1_register_offset[port]));
-
- __raw_writeb(gpio_int_unmasked[port] & gpio_int_enabled[port],
- EP93XX_GPIO_REG(int_en_register_offset[port]));
-}
-
-void ep93xx_gpio_int_mask(unsigned line)
-{
- gpio_int_unmasked[line >> 3] &= ~(1 << (line & 7));
-}
-
-void ep93xx_gpio_int_debounce(unsigned int irq, int enable)
-{
- int line = irq_to_gpio(irq);
- int port = line >> 3;
- int port_mask = 1 << (line & 7);
-
- if (enable)
- gpio_int_debounce[port] |= port_mask;
- else
- gpio_int_debounce[port] &= ~port_mask;
-
- __raw_writeb(gpio_int_debounce[port],
- EP93XX_GPIO_REG(int_debounce_register_offset[port]));
-}
-EXPORT_SYMBOL(ep93xx_gpio_int_debounce);
-
/*************************************************************************
* EP93xx IRQ handling
*************************************************************************/
-static void ep93xx_gpio_ab_irq_handler(unsigned int irq, struct irq_desc *desc)
-{
- unsigned char status;
- int i;
-
- status = __raw_readb(EP93XX_GPIO_A_INT_STATUS);
- for (i = 0; i < 8; i++) {
- if (status & (1 << i)) {
- int gpio_irq = gpio_to_irq(EP93XX_GPIO_LINE_A(0)) + i;
- generic_handle_irq(gpio_irq);
- }
- }
-
- status = __raw_readb(EP93XX_GPIO_B_INT_STATUS);
- for (i = 0; i < 8; i++) {
- if (status & (1 << i)) {
- int gpio_irq = gpio_to_irq(EP93XX_GPIO_LINE_B(0)) + i;
- generic_handle_irq(gpio_irq);
- }
- }
-}
-
-static void ep93xx_gpio_f_irq_handler(unsigned int irq, struct irq_desc *desc)
-{
- /*
- * map discontiguous hw irq range to continous sw irq range:
- *
- * IRQ_EP93XX_GPIO{0..7}MUX -> gpio_to_irq(EP93XX_GPIO_LINE_F({0..7})
- */
- int port_f_idx = ((irq + 1) & 7) ^ 4; /* {19..22,47..50} -> {0..7} */
- int gpio_irq = gpio_to_irq(EP93XX_GPIO_LINE_F(0)) + port_f_idx;
-
- generic_handle_irq(gpio_irq);
-}
-
-static void ep93xx_gpio_irq_ack(unsigned int irq)
-{
- int line = irq_to_gpio(irq);
- int port = line >> 3;
- int port_mask = 1 << (line & 7);
-
- if ((irq_desc[irq].status & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH) {
- gpio_int_type2[port] ^= port_mask; /* switch edge direction */
- ep93xx_gpio_update_int_params(port);
- }
-
- __raw_writeb(port_mask, EP93XX_GPIO_REG(eoi_register_offset[port]));
-}
-
-static void ep93xx_gpio_irq_mask_ack(unsigned int irq)
-{
- int line = irq_to_gpio(irq);
- int port = line >> 3;
- int port_mask = 1 << (line & 7);
-
- if ((irq_desc[irq].status & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH)
- gpio_int_type2[port] ^= port_mask; /* switch edge direction */
-
- gpio_int_unmasked[port] &= ~port_mask;
- ep93xx_gpio_update_int_params(port);
-
- __raw_writeb(port_mask, EP93XX_GPIO_REG(eoi_register_offset[port]));
-}
-
-static void ep93xx_gpio_irq_mask(unsigned int irq)
-{
- int line = irq_to_gpio(irq);
- int port = line >> 3;
-
- gpio_int_unmasked[port] &= ~(1 << (line & 7));
- ep93xx_gpio_update_int_params(port);
-}
-
-static void ep93xx_gpio_irq_unmask(unsigned int irq)
-{
- int line = irq_to_gpio(irq);
- int port = line >> 3;
-
- gpio_int_unmasked[port] |= 1 << (line & 7);
- ep93xx_gpio_update_int_params(port);
-}
-
-
-/*
- * gpio_int_type1 controls whether the interrupt is level (0) or
- * edge (1) triggered, while gpio_int_type2 controls whether it
- * triggers on low/falling (0) or high/rising (1).
- */
-static int ep93xx_gpio_irq_type(unsigned int irq, unsigned int type)
-{
- struct irq_desc *desc = irq_desc + irq;
- const int gpio = irq_to_gpio(irq);
- const int port = gpio >> 3;
- const int port_mask = 1 << (gpio & 7);
-
- gpio_direction_input(gpio);
-
- switch (type) {
- case IRQ_TYPE_EDGE_RISING:
- gpio_int_type1[port] |= port_mask;
- gpio_int_type2[port] |= port_mask;
- desc->handle_irq = handle_edge_irq;
- break;
- case IRQ_TYPE_EDGE_FALLING:
- gpio_int_type1[port] |= port_mask;
- gpio_int_type2[port] &= ~port_mask;
- desc->handle_irq = handle_edge_irq;
- break;
- case IRQ_TYPE_LEVEL_HIGH:
- gpio_int_type1[port] &= ~port_mask;
- gpio_int_type2[port] |= port_mask;
- desc->handle_irq = handle_level_irq;
- break;
- case IRQ_TYPE_LEVEL_LOW:
- gpio_int_type1[port] &= ~port_mask;
- gpio_int_type2[port] &= ~port_mask;
- desc->handle_irq = handle_level_irq;
- break;
- case IRQ_TYPE_EDGE_BOTH:
- gpio_int_type1[port] |= port_mask;
- /* set initial polarity based on current input level */
- if (gpio_get_value(gpio))
- gpio_int_type2[port] &= ~port_mask; /* falling */
- else
- gpio_int_type2[port] |= port_mask; /* rising */
- desc->handle_irq = handle_edge_irq;
- break;
- default:
- pr_err("ep93xx: failed to set irq type %d for gpio %d\n",
- type, gpio);
- return -EINVAL;
- }
-
- gpio_int_enabled[port] |= port_mask;
-
- desc->status &= ~IRQ_TYPE_SENSE_MASK;
- desc->status |= type & IRQ_TYPE_SENSE_MASK;
-
- ep93xx_gpio_update_int_params(port);
-
- return 0;
-}
-
-static struct irq_chip ep93xx_gpio_irq_chip = {
- .name = "GPIO",
- .ack = ep93xx_gpio_irq_ack,
- .mask_ack = ep93xx_gpio_irq_mask_ack,
- .mask = ep93xx_gpio_irq_mask,
- .unmask = ep93xx_gpio_irq_unmask,
- .set_type = ep93xx_gpio_irq_type,
-};
-
+extern void ep93xx_gpio_init_irq(void);
void __init ep93xx_init_irq(void)
{
- int gpio_irq;
-
vic_init(EP93XX_VIC1_BASE, 0, EP93XX_VIC1_VALID_IRQ_MASK, 0);
vic_init(EP93XX_VIC2_BASE, 32, EP93XX_VIC2_VALID_IRQ_MASK, 0);
- for (gpio_irq = gpio_to_irq(0);
- gpio_irq <= gpio_to_irq(EP93XX_GPIO_LINE_MAX_IRQ); ++gpio_irq) {
- set_irq_chip(gpio_irq, &ep93xx_gpio_irq_chip);
- set_irq_handler(gpio_irq, handle_level_irq);
- set_irq_flags(gpio_irq, IRQF_VALID);
- }
-
- set_irq_chained_handler(IRQ_EP93XX_GPIO_AB, ep93xx_gpio_ab_irq_handler);
- set_irq_chained_handler(IRQ_EP93XX_GPIO0MUX, ep93xx_gpio_f_irq_handler);
- set_irq_chained_handler(IRQ_EP93XX_GPIO1MUX, ep93xx_gpio_f_irq_handler);
- set_irq_chained_handler(IRQ_EP93XX_GPIO2MUX, ep93xx_gpio_f_irq_handler);
- set_irq_chained_handler(IRQ_EP93XX_GPIO3MUX, ep93xx_gpio_f_irq_handler);
- set_irq_chained_handler(IRQ_EP93XX_GPIO4MUX, ep93xx_gpio_f_irq_handler);
- set_irq_chained_handler(IRQ_EP93XX_GPIO5MUX, ep93xx_gpio_f_irq_handler);
- set_irq_chained_handler(IRQ_EP93XX_GPIO6MUX, ep93xx_gpio_f_irq_handler);
- set_irq_chained_handler(IRQ_EP93XX_GPIO7MUX, ep93xx_gpio_f_irq_handler);
+ ep93xx_gpio_init_irq();
}
* CMOS driver.
*/
if (data->sda_is_open_drain && data->sda_pin != EP93XX_GPIO_LINE_EEDAT)
- pr_warning("ep93xx: sda != EEDAT, open drain has no effect\n");
+ pr_warning("sda != EEDAT, open drain has no effect\n");
if (data->scl_is_open_drain && data->scl_pin != EP93XX_GPIO_LINE_EECLK)
- pr_warning("ep93xx: scl != EECLK, open drain has no effect\n");
+ pr_warning("scl != EECLK, open drain has no effect\n");
__raw_writel((data->sda_is_open_drain << 1) |
(data->scl_is_open_drain << 0),
projects / deliverable / linux.git / blobdiff