/* BFD back-end for Hitachi H8/300 COFF binaries.
- Copyright 1990, 91, 92, 93, 94, 95, 96, 1997 Free Software Foundation, Inc.
+ Copyright 1990, 91, 92, 93, 94, 95, 96, 97, 98, 1999
+ Free Software Foundation, Inc.
Written by Steve Chamberlain, <sac@cygnus.com>.
This file is part of BFD, the Binary File Descriptor library.
#define COFF_DEFAULT_SECTION_ALIGNMENT_POWER (1)
/* We derive a hash table from the basic BFD hash table to
- hold entries in the function vector. Aside from the
+ hold entries in the function vector. Aside from the
info stored by the basic hash table, we need the offset
of a particular entry within the hash table as well as
the offset where we'll add the next entry. */
return &ret->root.root;
}
-/* special handling for H8/300 relocs.
+/* Special handling for H8/300 relocs.
We only come here for pcrel stuff and return normally if not an -r link.
When doing -r, we can't do any arithmetic for the pcrel stuff, because
the code in reloc.c assumes that we can manipulate the targets of
- the pcrel branches. This isn't so, since the H8/300 can do relaxing,
+ the pcrel branches. This isn't so, since the H8/300 can do relaxing,
which means that the gap after the instruction may not be enough to
- contain the offset required for the branch, so we have to use the only
- the addend until the final link */
+ contain the offset required for the branch, so we have to use only
+ the addend until the final link. */
static bfd_reloc_status_type
special (abfd, reloc_entry, symbol, data, input_section, output_bfd,
- error_message)
- bfd *abfd;
- arelent *reloc_entry;
- asymbol *symbol;
- PTR data;
- asection *input_section;
+ error_message)
+ bfd *abfd ATTRIBUTE_UNUSED;
+ arelent *reloc_entry ATTRIBUTE_UNUSED;
+ asymbol *symbol ATTRIBUTE_UNUSED;
+ PTR data ATTRIBUTE_UNUSED;
+ asection *input_section ATTRIBUTE_UNUSED;
bfd *output_bfd;
- char **error_message;
+ char **error_message ATTRIBUTE_UNUSED;
{
if (output_bfd == (bfd *) NULL)
return bfd_reloc_continue;
+ /* Adjust the reloc address to that in the output section. */
+ reloc_entry->address += input_section->output_offset;
return bfd_reloc_ok;
}
HOWTO (R_JMP_DEL, 0, 0, 8, true, 0, complain_overflow_signed, special, "Deleted jump", false, 0x000000ff, 0x000000ff, true),
};
-
-/* Turn a howto into a reloc number */
+/* Turn a howto into a reloc number. */
#define SELECT_RELOC(x,howto) \
{ x.r_type = select_reloc(howto); }
#define H8300 1 /* Customize coffcode.h */
#define __A_MAGIC_SET__
-
-
-/* Code to swap in the reloc */
+/* Code to swap in the reloc. */
#define SWAP_IN_RELOC_OFFSET bfd_h_get_32
#define SWAP_OUT_RELOC_OFFSET bfd_h_put_32
#define SWAP_OUT_RELOC_EXTRA(abfd, src, dst) \
dst->r_stuff[0] = 'S'; \
dst->r_stuff[1] = 'C';
-
static int
select_reloc (howto)
reloc_howto_type *howto;
return howto->type;
}
-/* Code to turn a r_type into a howto ptr, uses the above howto table
- */
+/* Code to turn a r_type into a howto ptr, uses the above howto table. */
static void
rtype2howto (internal, dst)
#define RTYPE2HOWTO(internal, relocentry) rtype2howto(internal,relocentry)
-
-/* Perform any necessary magic to the addend in a reloc entry */
-
+/* Perform any necessary magic to the addend in a reloc entry. */
#define CALC_ADDEND(abfd, symbol, ext_reloc, cache_ptr) \
cache_ptr->addend = ext_reloc.r_offset;
-
#define RELOC_PROCESSING(relent,reloc,symbols,abfd,section) \
reloc_processing(relent, reloc, symbols, abfd, section)
static void
reloc_processing (relent, reloc, symbols, abfd, section)
- arelent * relent;
+ arelent *relent;
struct internal_reloc *reloc;
- asymbol ** symbols;
- bfd * abfd;
- asection * section;
+ asymbol **symbols;
+ bfd *abfd;
+ asection *section;
{
relent->address = reloc->r_vaddr;
rtype2howto (relent, reloc);
relent->sym_ptr_ptr = bfd_abs_section_ptr->symbol_ptr_ptr;
}
-
-
relent->addend = reloc->r_offset;
relent->address -= section->vma;
- /* relent->section = 0;*/
+#if 0
+ relent->section = 0;
+#endif
}
static boolean
/* Search all the symbols for one in INPUT_SECTION with
address ADDRESS. */
- while (*s)
+ while (*s)
{
asymbol *p = *s;
if (p->section == input_section
+ p->value) == address)
return true;
s++;
- }
+ }
return false;
}
-
/* If RELOC represents a relaxable instruction/reloc, change it into
the relaxed reloc, notify the linker that symbol addresses
have changed (bfd_perform_slip) and return how much the current
in the howto table. This needs to be fixed. */
static int
-h8300_reloc16_estimate(abfd, input_section, reloc, shrink, link_info)
+h8300_reloc16_estimate (abfd, input_section, reloc, shrink, link_info)
bfd *abfd;
asection *input_section;
arelent *reloc;
unsigned int shrink;
struct bfd_link_info *link_info;
{
- bfd_vma value;
+ bfd_vma value;
bfd_vma dot;
bfd_vma gap;
static asection *last_input_section = NULL;
static arelent *last_reloc = NULL;
- /* The address of the thing to be relocated will have moved back by
+ /* The address of the thing to be relocated will have moved back by
the size of the shrink - but we don't change reloc->address here,
since we need it to know where the relocation lives in the source
uncooked section. */
/* Only examine the relocs which might be relaxable. */
switch (reloc->howto->type)
- {
-
+ {
/* This is the 16/24 bit absolute branch which could become an 8 bit
pc-relative branch. */
case R_JMP1:
case R_JMPL1:
/* Get the address of the target of this branch. */
- value = bfd_coff_reloc16_get_value(reloc, link_info, input_section);
+ value = bfd_coff_reloc16_get_value (reloc, link_info, input_section);
/* Get the address of the next instruction (not the reloc). */
dot = (input_section->output_section->vma
/* Compute the distance from this insn to the branch target. */
gap = value - dot;
-
+
/* If the distance is within -128..+128 inclusive, then we can relax
this jump. +128 is valid since the target will move two bytes
closer if we do relax this branch. */
if ((int)gap >= -128 && (int)gap <= 128 )
- {
-
+ {
/* It's possible we may be able to eliminate this branch entirely;
if the previous instruction is a branch around this instruction,
and there's no label at this instruction, then we can reverse
bCC lab1 bCC' lab2
jmp lab2
lab1: lab1:
-
+
This saves 4 bytes instead of two, and should be relatively
common. */
if (last_value == dot + 2
&& last_reloc->address + 1 == reloc->address
- && ! h8300_symbol_address_p (abfd, input_section, dot - 2))
+ && !h8300_symbol_address_p (abfd, input_section, dot - 2))
{
reloc->howto = howto_table + 19;
last_reloc->howto = howto_table + 18;
}
/* Change the reloc type. */
- reloc->howto = reloc->howto + 1;
+ reloc->howto = reloc->howto + 1;
/* This shrinks this section by two bytes. */
shrink += 2;
- bfd_perform_slip(abfd, 2, input_section, address);
+ bfd_perform_slip (abfd, 2, input_section, address);
}
break;
case R_PCRWORD:
/* Get the address of the target of this branch, add one to the value
because the addend field in PCrel jumps is off by -1. */
- value = bfd_coff_reloc16_get_value(reloc, link_info, input_section) + 1;
-
+ value = bfd_coff_reloc16_get_value (reloc, link_info, input_section) + 1;
+
/* Get the address of the next instruction if we were to relax. */
dot = input_section->output_section->vma +
input_section->output_offset + address;
-
+
/* Compute the distance from this insn to the branch target. */
gap = value - dot;
this jump. +128 is valid since the target will move two bytes
closer if we do relax this branch. */
if ((int)gap >= -128 && (int)gap <= 128 )
- {
+ {
/* Change the reloc type. */
reloc->howto = howto_table + 15;
/* This shrinks this section by two bytes. */
shrink += 2;
- bfd_perform_slip(abfd, 2, input_section, address);
+ bfd_perform_slip (abfd, 2, input_section, address);
}
break;
become an 8 bit absolute address if it's in the right range. */
case R_MOV16B1:
/* Get the address of the data referenced by this mov.b insn. */
- value = bfd_coff_reloc16_get_value(reloc, link_info, input_section);
+ value = bfd_coff_reloc16_get_value (reloc, link_info, input_section);
/* The address is in 0xff00..0xffff inclusive on the h8300 or
0xffff00..0xffffff inclusive on the h8300h, then we can
/* This shrinks this section by two bytes. */
shrink += 2;
- bfd_perform_slip(abfd, 2, input_section, address);
+ bfd_perform_slip (abfd, 2, input_section, address);
}
break;
and try to relax it into a 16bit absolute. */
case R_MOV24B1:
/* Get the address of the data referenced by this mov.b insn. */
- value = bfd_coff_reloc16_get_value(reloc, link_info, input_section);
+ value = bfd_coff_reloc16_get_value (reloc, link_info, input_section);
/* The address is in 0xffff00..0xffffff inclusive on the h8300h,
then we can relax this mov.b */
/* This shrinks this section by four bytes. */
shrink += 4;
- bfd_perform_slip(abfd, 4, input_section, address);
+ bfd_perform_slip (abfd, 4, input_section, address);
/* Done with this reloc. */
break;
become an 16 bit absolute address if it's in the right range. */
case R_MOVL1:
/* Get the address of the data referenced by this mov insn. */
- value = bfd_coff_reloc16_get_value(reloc, link_info, input_section);
+ value = bfd_coff_reloc16_get_value (reloc, link_info, input_section);
/* If this address is in 0x0000..0x7fff inclusive or
0xff8000..0xffffff inclusive, then it can be relaxed. */
/* This shrinks this section by two bytes. */
shrink += 2;
- bfd_perform_slip(abfd, 2, input_section, address);
+ bfd_perform_slip (abfd, 2, input_section, address);
}
break;
/* No other reloc types represent relaxing opportunities. */
- default:
- break;
+ default:
+ break;
}
last_reloc = reloc;
return shrink;
}
-
/* Handle relocations for the H8/300, including relocs for relaxed
instructions.
asection *input_section = link_order->u.indirect.section;
bfd_vma value;
bfd_vma dot;
- int gap,tmp;
+ int gap, tmp;
switch (reloc->howto->type)
{
-
/* Generic 8bit pc-relative relocation. */
case R_PCRBYTE:
/* Get the address of the target of this branch. */
- value = bfd_coff_reloc16_get_value(reloc, link_info, input_section);
+ value = bfd_coff_reloc16_get_value (reloc, link_info, input_section);
- dot = (link_order->offset
- + dst_address
+ dot = (link_order->offset
+ + dst_address
+ link_order->u.indirect.section->output_section->vma);
gap = value - dot;
/* Generic 16bit pc-relative relocation. */
case R_PCRWORD:
/* Get the address of the target of this branch. */
- value = bfd_coff_reloc16_get_value(reloc, link_info, input_section);
+ value = bfd_coff_reloc16_get_value (reloc, link_info, input_section);
/* Get the address of the instruction (not the reloc). */
- dot = (link_order->offset
- + dst_address
+ dot = (link_order->offset
+ + dst_address
+ link_order->u.indirect.section->output_section->vma + 1);
gap = value - dot;
case R_MOV16B1:
case R_JMP1:
case R_RELWORD:
- value = bfd_coff_reloc16_get_value(reloc, link_info, input_section);
+ value = bfd_coff_reloc16_get_value (reloc, link_info, input_section);
bfd_put_16 (abfd, value, data + dst_address);
dst_address += 2;
src_address += 2;
case R_MOVL1:
case R_RELLONG:
/* Get the address of the target of this branch. */
- value = bfd_coff_reloc16_get_value (reloc, link_info, input_section),
+ value = bfd_coff_reloc16_get_value (reloc, link_info, input_section);
bfd_put_32 (abfd, value, data + dst_address);
dst_address += 4;
src_address += 4;
value = bfd_coff_reloc16_get_value (reloc, link_info, input_section);
/* Sanity check. */
- if (value < 0x8000 || value > 0xff8000)
+ if (value <= 0x7fff || value >= 0xff8000)
{
/* Insert the 16bit value into the proper location. */
bfd_put_16 (abfd, value, data + dst_address);
bfd_put_8 (abfd, tmp, data + dst_address - 2);
break;
+ case 0x5c:
+ /* bsr:16 -> bsr:8 */
+ bfd_put_8 (abfd, 0x55, data + dst_address - 2);
+ break;
+
default:
abort ();
}
src_address += 2;
break;
-
+
/* Similarly for a 24bit absolute that is now 8 bits. */
case R_JMPL2:
/* Get the address of the target of this branch. */
abort ();
/* Fix up the opcode. */
- switch (data[src_address-1] & 0xf0)
+ switch (data[src_address - 1] & 0xf0)
{
case 0x00:
- data[dst_address - 2] = (data[src_address-1] & 0xf) | 0x20;
+ data[dst_address - 2] = (data[src_address - 1] & 0xf) | 0x20;
break;
case 0x80:
- data[dst_address - 2] = (data[src_address-1] & 0xf) | 0x30;
+ data[dst_address - 2] = (data[src_address - 1] & 0xf) | 0x30;
break;
default:
abort ();
abort ();
/* Fix up the opcode. */
- switch (data[src_address-1] & 0xf0)
+ switch (data[src_address - 1] & 0xf0)
{
case 0x20:
- data[dst_address - 2] = (data[src_address-1] & 0xf) | 0x20;
+ data[dst_address - 2] = (data[src_address - 1] & 0xf) | 0x20;
break;
case 0xa0:
- data[dst_address - 2] = (data[src_address-1] & 0xf) | 0x30;
+ data[dst_address - 2] = (data[src_address - 1] & 0xf) | 0x30;
break;
default:
abort ();
case R_BCC_INV:
/* Get the address of the target of this branch. */
- value = bfd_coff_reloc16_get_value(reloc, link_info, input_section);
+ value = bfd_coff_reloc16_get_value (reloc, link_info, input_section);
- dot = (link_order->offset
- + dst_address
+ dot = (link_order->offset
+ + dst_address
+ link_order->u.indirect.section->output_section->vma) + 1;
gap = value - dot;
symbol = *(reloc->sym_ptr_ptr);
value = bfd_coff_reloc16_get_value (reloc, link_info, input_section);
if (symbol == bfd_abs_section_ptr->symbol
- || (value >= 0 && value <= 0xff))
+ || value <= 0xff)
{
/* This should be handled in a manner very similar to
R_RELBYTES. If the value is in range, then just slam
the value into the right location. Else trigger a
reloc overflow callback. */
- if (value >= 0 && value <= 0xff)
+ if (value <= 0xff)
{
bfd_put_8 (abfd, value, data + dst_address);
dst_address += 1;
}
/* This is a jump/call through a function vector, and we're
- expected to create the function vector ourselves.
+ expected to create the function vector ourselves.
First look up this symbol in the linker hash table -- we need
the derived linker symbol which holds this symbol's index
strcpy (new_name, name);
sprintf (new_name + strlen (name), "_%08x",
- (int)symbol->section);
+ (int) symbol->section);
name = new_name;
}
*dst_ptr = dst_address;
}
-
/* Routine for the h8300 linker.
This routine is necessary to handle the special R_MEM_INDIRECT
selected static symbols to the bfd linker hash table. */
static boolean
-h8300_bfd_link_add_symbols(abfd, info)
+h8300_bfd_link_add_symbols (abfd, info)
bfd *abfd;
struct bfd_link_info *info;
{
if (reloc_size <= 0)
continue;
- relocs = (arelent **)bfd_malloc ((size_t)reloc_size);
+ relocs = (arelent **) bfd_malloc ((size_t) reloc_size);
if (!relocs)
return false;
strcpy (new_name, name);
sprintf (new_name + strlen (name), "_%08x",
- (int)symbol->section);
+ (int) symbol->section);
name = new_name;
}
h = funcvec_hash_lookup (h8300_coff_hash_table (info)->funcvec_hash_table,
name, false, false);
-
/* If this symbol isn't already in the hash table, add
it and bump up the size of the hash table. */
if (h == NULL)
#define COFF_LONG_FILENAMES
#include "coffcode.h"
-
#undef coff_bfd_get_relocated_section_contents
#undef coff_bfd_relax_section
#define coff_bfd_get_relocated_section_contents \
bfd_coff_reloc16_get_relocated_section_contents
#define coff_bfd_relax_section bfd_coff_reloc16_relax_section
-
-
-const bfd_target h8300coff_vec =
-{
- "coff-h8300", /* name */
- bfd_target_coff_flavour,
- BFD_ENDIAN_BIG, /* data byte order is big */
- BFD_ENDIAN_BIG, /* header byte order is big */
-
- (HAS_RELOC | EXEC_P | /* object flags */
- HAS_LINENO | HAS_DEBUG |
- HAS_SYMS | HAS_LOCALS | WP_TEXT | BFD_IS_RELAXABLE ),
- (SEC_HAS_CONTENTS | SEC_ALLOC | SEC_LOAD | SEC_RELOC), /* section flags */
- '_', /* leading char */
- '/', /* ar_pad_char */
- 15, /* ar_max_namelen */
- bfd_getb64, bfd_getb_signed_64, bfd_putb64,
- bfd_getb32, bfd_getb_signed_32, bfd_putb32,
- bfd_getb16, bfd_getb_signed_16, bfd_putb16, /* data */
- bfd_getb64, bfd_getb_signed_64, bfd_putb64,
- bfd_getb32, bfd_getb_signed_32, bfd_putb32,
- bfd_getb16, bfd_getb_signed_16, bfd_putb16, /* hdrs */
-
- {_bfd_dummy_target, coff_object_p, /* bfd_check_format */
- bfd_generic_archive_p, _bfd_dummy_target},
- {bfd_false, coff_mkobject, _bfd_generic_mkarchive, /* bfd_set_format */
- bfd_false},
- {bfd_false, coff_write_object_contents, /* bfd_write_contents */
- _bfd_write_archive_contents, bfd_false},
-
- BFD_JUMP_TABLE_GENERIC (coff),
- BFD_JUMP_TABLE_COPY (coff),
- BFD_JUMP_TABLE_CORE (_bfd_nocore),
- BFD_JUMP_TABLE_ARCHIVE (_bfd_archive_coff),
- BFD_JUMP_TABLE_SYMBOLS (coff),
- BFD_JUMP_TABLE_RELOCS (coff),
- BFD_JUMP_TABLE_WRITE (coff),
- BFD_JUMP_TABLE_LINK (coff),
- BFD_JUMP_TABLE_DYNAMIC (_bfd_nodynamic),
-
- COFF_SWAP_TABLE,
-};
+CREATE_BIG_COFF_TARGET_VEC (h8300coff_vec, "coff-h8300", BFD_IS_RELAXABLE, 0, '_', NULL)
projects / deliverable / binutils-gdb.git / blobdiff