struct iwl_priv; /* FIXME: remove */
#include "iwl-debug.h"
#include "iwl-eeprom.h"
-#include "iwl-4965.h" /* FIXME: remove */
+#include "iwl-dev.h" /* FIXME: remove */
#include "iwl-core.h"
+#include "iwl-io.h"
#include "iwl-rfkill.h"
+#include "iwl-power.h"
MODULE_DESCRIPTION("iwl core");
EXPORT_SYMBOL(iwl_debug_level);
#endif
+#define IWL_DECLARE_RATE_INFO(r, s, ip, in, rp, rn, pp, np) \
+ [IWL_RATE_##r##M_INDEX] = { IWL_RATE_##r##M_PLCP, \
+ IWL_RATE_SISO_##s##M_PLCP, \
+ IWL_RATE_MIMO2_##s##M_PLCP,\
+ IWL_RATE_MIMO3_##s##M_PLCP,\
+ IWL_RATE_##r##M_IEEE, \
+ IWL_RATE_##ip##M_INDEX, \
+ IWL_RATE_##in##M_INDEX, \
+ IWL_RATE_##rp##M_INDEX, \
+ IWL_RATE_##rn##M_INDEX, \
+ IWL_RATE_##pp##M_INDEX, \
+ IWL_RATE_##np##M_INDEX }
+
+/*
+ * Parameter order:
+ * rate, ht rate, prev rate, next rate, prev tgg rate, next tgg rate
+ *
+ * If there isn't a valid next or previous rate then INV is used which
+ * maps to IWL_RATE_INVALID
+ *
+ */
+const struct iwl4965_rate_info iwl4965_rates[IWL_RATE_COUNT] = {
+ IWL_DECLARE_RATE_INFO(1, INV, INV, 2, INV, 2, INV, 2), /* 1mbps */
+ IWL_DECLARE_RATE_INFO(2, INV, 1, 5, 1, 5, 1, 5), /* 2mbps */
+ IWL_DECLARE_RATE_INFO(5, INV, 2, 6, 2, 11, 2, 11), /*5.5mbps */
+ IWL_DECLARE_RATE_INFO(11, INV, 9, 12, 9, 12, 5, 18), /* 11mbps */
+ IWL_DECLARE_RATE_INFO(6, 6, 5, 9, 5, 11, 5, 11), /* 6mbps */
+ IWL_DECLARE_RATE_INFO(9, 6, 6, 11, 6, 11, 5, 11), /* 9mbps */
+ IWL_DECLARE_RATE_INFO(12, 12, 11, 18, 11, 18, 11, 18), /* 12mbps */
+ IWL_DECLARE_RATE_INFO(18, 18, 12, 24, 12, 24, 11, 24), /* 18mbps */
+ IWL_DECLARE_RATE_INFO(24, 24, 18, 36, 18, 36, 18, 36), /* 24mbps */
+ IWL_DECLARE_RATE_INFO(36, 36, 24, 48, 24, 48, 24, 48), /* 36mbps */
+ IWL_DECLARE_RATE_INFO(48, 48, 36, 54, 36, 54, 36, 54), /* 48mbps */
+ IWL_DECLARE_RATE_INFO(54, 54, 48, INV, 48, INV, 48, INV),/* 54mbps */
+ IWL_DECLARE_RATE_INFO(60, 60, 48, INV, 48, INV, 48, INV),/* 60mbps */
+ /* FIXME:RS: ^^ should be INV (legacy) */
+};
+EXPORT_SYMBOL(iwl4965_rates);
+
/* This function both allocates and initializes hw and priv. */
struct ieee80211_hw *iwl_alloc_all(struct iwl_cfg *cfg,
struct ieee80211_ops *hw_ops)
}
EXPORT_SYMBOL(iwl_alloc_all);
+void iwl_hw_detect(struct iwl_priv *priv)
+{
+ priv->hw_rev = _iwl_read32(priv, CSR_HW_REV);
+ priv->hw_wa_rev = _iwl_read32(priv, CSR_HW_REV_WA_REG);
+ pci_read_config_byte(priv->pci_dev, PCI_REVISION_ID, &priv->rev_id);
+}
+EXPORT_SYMBOL(iwl_hw_detect);
+
/**
* iwlcore_clear_stations_table - Clear the driver's station table
*
}
EXPORT_SYMBOL(iwlcore_clear_stations_table);
-void iwlcore_reset_qos(struct iwl_priv *priv)
+void iwl_reset_qos(struct iwl_priv *priv)
{
u16 cw_min = 15;
u16 cw_max = 1023;
spin_unlock_irqrestore(&priv->lock, flags);
}
-EXPORT_SYMBOL(iwlcore_reset_qos);
+EXPORT_SYMBOL(iwl_reset_qos);
+
+#ifdef CONFIG_IWL4965_HT
+static void iwlcore_init_ht_hw_capab(const struct iwl_priv *priv,
+ struct ieee80211_ht_info *ht_info,
+ enum ieee80211_band band)
+{
+ ht_info->cap = 0;
+ memset(ht_info->supp_mcs_set, 0, 16);
+
+ ht_info->ht_supported = 1;
+
+ if (priv->hw_params.fat_channel & BIT(band)) {
+ ht_info->cap |= (u16)IEEE80211_HT_CAP_SUP_WIDTH;
+ ht_info->cap |= (u16)IEEE80211_HT_CAP_SGI_40;
+ ht_info->supp_mcs_set[4] = 0x01;
+ }
+ ht_info->cap |= (u16)IEEE80211_HT_CAP_GRN_FLD;
+ ht_info->cap |= (u16)IEEE80211_HT_CAP_SGI_20;
+ ht_info->cap |= (u16)(IEEE80211_HT_CAP_MIMO_PS &
+ (IWL_MIMO_PS_NONE << 2));
+
+ if (priv->cfg->mod_params->amsdu_size_8K)
+ ht_info->cap |= (u16)IEEE80211_HT_CAP_MAX_AMSDU;
+
+ ht_info->ampdu_factor = CFG_HT_RX_AMPDU_FACTOR_DEF;
+ ht_info->ampdu_density = CFG_HT_MPDU_DENSITY_DEF;
+
+ ht_info->supp_mcs_set[0] = 0xFF;
+ if (priv->hw_params.tx_chains_num >= 2)
+ ht_info->supp_mcs_set[1] = 0xFF;
+ if (priv->hw_params.tx_chains_num >= 3)
+ ht_info->supp_mcs_set[2] = 0xFF;
+}
+#endif /* CONFIG_IWL4965_HT */
+
+static void iwlcore_init_hw_rates(struct iwl_priv *priv,
+ struct ieee80211_rate *rates)
+{
+ int i;
+
+ for (i = 0; i < IWL_RATE_COUNT; i++) {
+ rates[i].bitrate = iwl4965_rates[i].ieee * 5;
+ rates[i].hw_value = i; /* Rate scaling will work on indexes */
+ rates[i].hw_value_short = i;
+ rates[i].flags = 0;
+ if ((i > IWL_LAST_OFDM_RATE) || (i < IWL_FIRST_OFDM_RATE)) {
+ /*
+ * If CCK != 1M then set short preamble rate flag.
+ */
+ rates[i].flags |=
+ (iwl4965_rates[i].plcp == IWL_RATE_1M_PLCP) ?
+ 0 : IEEE80211_RATE_SHORT_PREAMBLE;
+ }
+ }
+}
+
+/**
+ * iwlcore_init_geos - Initialize mac80211's geo/channel info based from eeprom
+ */
+static int iwlcore_init_geos(struct iwl_priv *priv)
+{
+ struct iwl_channel_info *ch;
+ struct ieee80211_supported_band *sband;
+ struct ieee80211_channel *channels;
+ struct ieee80211_channel *geo_ch;
+ struct ieee80211_rate *rates;
+ int i = 0;
+
+ if (priv->bands[IEEE80211_BAND_2GHZ].n_bitrates ||
+ priv->bands[IEEE80211_BAND_5GHZ].n_bitrates) {
+ IWL_DEBUG_INFO("Geography modes already initialized.\n");
+ set_bit(STATUS_GEO_CONFIGURED, &priv->status);
+ return 0;
+ }
+
+ channels = kzalloc(sizeof(struct ieee80211_channel) *
+ priv->channel_count, GFP_KERNEL);
+ if (!channels)
+ return -ENOMEM;
+
+ rates = kzalloc((sizeof(struct ieee80211_rate) * (IWL_RATE_COUNT + 1)),
+ GFP_KERNEL);
+ if (!rates) {
+ kfree(channels);
+ return -ENOMEM;
+ }
+
+ /* 5.2GHz channels start after the 2.4GHz channels */
+ sband = &priv->bands[IEEE80211_BAND_5GHZ];
+ sband->channels = &channels[ARRAY_SIZE(iwl_eeprom_band_1)];
+ /* just OFDM */
+ sband->bitrates = &rates[IWL_FIRST_OFDM_RATE];
+ sband->n_bitrates = IWL_RATE_COUNT - IWL_FIRST_OFDM_RATE;
+
+ iwlcore_init_ht_hw_capab(priv, &sband->ht_info, IEEE80211_BAND_5GHZ);
+
+ sband = &priv->bands[IEEE80211_BAND_2GHZ];
+ sband->channels = channels;
+ /* OFDM & CCK */
+ sband->bitrates = rates;
+ sband->n_bitrates = IWL_RATE_COUNT;
+
+ iwlcore_init_ht_hw_capab(priv, &sband->ht_info, IEEE80211_BAND_2GHZ);
+
+ priv->ieee_channels = channels;
+ priv->ieee_rates = rates;
+
+ iwlcore_init_hw_rates(priv, rates);
+
+ for (i = 0; i < priv->channel_count; i++) {
+ ch = &priv->channel_info[i];
+
+ /* FIXME: might be removed if scan is OK */
+ if (!is_channel_valid(ch))
+ continue;
+
+ if (is_channel_a_band(ch))
+ sband = &priv->bands[IEEE80211_BAND_5GHZ];
+ else
+ sband = &priv->bands[IEEE80211_BAND_2GHZ];
+
+ geo_ch = &sband->channels[sband->n_channels++];
+
+ geo_ch->center_freq =
+ ieee80211_channel_to_frequency(ch->channel);
+ geo_ch->max_power = ch->max_power_avg;
+ geo_ch->max_antenna_gain = 0xff;
+ geo_ch->hw_value = ch->channel;
+
+ if (is_channel_valid(ch)) {
+ if (!(ch->flags & EEPROM_CHANNEL_IBSS))
+ geo_ch->flags |= IEEE80211_CHAN_NO_IBSS;
+
+ if (!(ch->flags & EEPROM_CHANNEL_ACTIVE))
+ geo_ch->flags |= IEEE80211_CHAN_PASSIVE_SCAN;
+
+ if (ch->flags & EEPROM_CHANNEL_RADAR)
+ geo_ch->flags |= IEEE80211_CHAN_RADAR;
+
+ if (ch->max_power_avg > priv->max_channel_txpower_limit)
+ priv->max_channel_txpower_limit =
+ ch->max_power_avg;
+ } else {
+ geo_ch->flags |= IEEE80211_CHAN_DISABLED;
+ }
+
+ /* Save flags for reg domain usage */
+ geo_ch->orig_flags = geo_ch->flags;
+
+ IWL_DEBUG_INFO("Channel %d Freq=%d[%sGHz] %s flag=0%X\n",
+ ch->channel, geo_ch->center_freq,
+ is_channel_a_band(ch) ? "5.2" : "2.4",
+ geo_ch->flags & IEEE80211_CHAN_DISABLED ?
+ "restricted" : "valid",
+ geo_ch->flags);
+ }
+
+ if ((priv->bands[IEEE80211_BAND_5GHZ].n_channels == 0) &&
+ priv->cfg->sku & IWL_SKU_A) {
+ printk(KERN_INFO DRV_NAME
+ ": Incorrectly detected BG card as ABG. Please send "
+ "your PCI ID 0x%04X:0x%04X to maintainer.\n",
+ priv->pci_dev->device, priv->pci_dev->subsystem_device);
+ priv->cfg->sku &= ~IWL_SKU_A;
+ }
+
+ printk(KERN_INFO DRV_NAME
+ ": Tunable channels: %d 802.11bg, %d 802.11a channels\n",
+ priv->bands[IEEE80211_BAND_2GHZ].n_channels,
+ priv->bands[IEEE80211_BAND_5GHZ].n_channels);
+
+ if (priv->bands[IEEE80211_BAND_2GHZ].n_channels)
+ priv->hw->wiphy->bands[IEEE80211_BAND_2GHZ] =
+ &priv->bands[IEEE80211_BAND_2GHZ];
+ if (priv->bands[IEEE80211_BAND_5GHZ].n_channels)
+ priv->hw->wiphy->bands[IEEE80211_BAND_5GHZ] =
+ &priv->bands[IEEE80211_BAND_5GHZ];
+
+ set_bit(STATUS_GEO_CONFIGURED, &priv->status);
+
+ return 0;
+}
+
+/*
+ * iwlcore_free_geos - undo allocations in iwlcore_init_geos
+ */
+void iwlcore_free_geos(struct iwl_priv *priv)
+{
+ kfree(priv->ieee_channels);
+ kfree(priv->ieee_rates);
+ clear_bit(STATUS_GEO_CONFIGURED, &priv->status);
+}
+EXPORT_SYMBOL(iwlcore_free_geos);
+
+#ifdef CONFIG_IWL4965_HT
+static u8 is_single_rx_stream(struct iwl_priv *priv)
+{
+ return !priv->current_ht_config.is_ht ||
+ ((priv->current_ht_config.supp_mcs_set[1] == 0) &&
+ (priv->current_ht_config.supp_mcs_set[2] == 0)) ||
+ priv->ps_mode == IWL_MIMO_PS_STATIC;
+}
+#else
+static inline u8 is_single_rx_stream(struct iwl_priv *priv)
+{
+ return 1;
+}
+#endif /*CONFIG_IWL4965_HT */
+
+/*
+ * Determine how many receiver/antenna chains to use.
+ * More provides better reception via diversity. Fewer saves power.
+ * MIMO (dual stream) requires at least 2, but works better with 3.
+ * This does not determine *which* chains to use, just how many.
+ */
+static int iwlcore_get_rx_chain_counter(struct iwl_priv *priv,
+ u8 *idle_state, u8 *rx_state)
+{
+ u8 is_single = is_single_rx_stream(priv);
+ u8 is_cam = test_bit(STATUS_POWER_PMI, &priv->status) ? 0 : 1;
+
+ /* # of Rx chains to use when expecting MIMO. */
+ if (is_single || (!is_cam && (priv->ps_mode == IWL_MIMO_PS_STATIC)))
+ *rx_state = 2;
+ else
+ *rx_state = 3;
+
+ /* # Rx chains when idling and maybe trying to save power */
+ switch (priv->ps_mode) {
+ case IWL_MIMO_PS_STATIC:
+ case IWL_MIMO_PS_DYNAMIC:
+ *idle_state = (is_cam) ? 2 : 1;
+ break;
+ case IWL_MIMO_PS_NONE:
+ *idle_state = (is_cam) ? *rx_state : 1;
+ break;
+ default:
+ *idle_state = 1;
+ break;
+ }
+
+ return 0;
+}
+
+/**
+ * iwl_set_rxon_chain - Set up Rx chain usage in "staging" RXON image
+ *
+ * Selects how many and which Rx receivers/antennas/chains to use.
+ * This should not be used for scan command ... it puts data in wrong place.
+ */
+void iwl_set_rxon_chain(struct iwl_priv *priv)
+{
+ u8 is_single = is_single_rx_stream(priv);
+ u8 idle_state, rx_state;
+
+ priv->staging_rxon.rx_chain = 0;
+ rx_state = idle_state = 3;
+
+ /* Tell uCode which antennas are actually connected.
+ * Before first association, we assume all antennas are connected.
+ * Just after first association, iwl_chain_noise_calibration()
+ * checks which antennas actually *are* connected. */
+ priv->staging_rxon.rx_chain |=
+ cpu_to_le16(priv->hw_params.valid_rx_ant <<
+ RXON_RX_CHAIN_VALID_POS);
+
+ /* How many receivers should we use? */
+ iwlcore_get_rx_chain_counter(priv, &idle_state, &rx_state);
+ priv->staging_rxon.rx_chain |=
+ cpu_to_le16(rx_state << RXON_RX_CHAIN_MIMO_CNT_POS);
+ priv->staging_rxon.rx_chain |=
+ cpu_to_le16(idle_state << RXON_RX_CHAIN_CNT_POS);
+
+ if (!is_single && (rx_state >= 2) &&
+ !test_bit(STATUS_POWER_PMI, &priv->status))
+ priv->staging_rxon.rx_chain |= RXON_RX_CHAIN_MIMO_FORCE_MSK;
+ else
+ priv->staging_rxon.rx_chain &= ~RXON_RX_CHAIN_MIMO_FORCE_MSK;
+
+ IWL_DEBUG_ASSOC("rx chain %X\n", priv->staging_rxon.rx_chain);
+}
+EXPORT_SYMBOL(iwl_set_rxon_chain);
/**
* iwlcore_set_rxon_channel - Set the phymode and channel values in staging RXON
* NOTE: Does not commit to the hardware; it sets appropriate bit fields
* in the staging RXON flag structure based on the phymode
*/
-int iwlcore_set_rxon_channel(struct iwl_priv *priv,
+int iwl_set_rxon_channel(struct iwl_priv *priv,
enum ieee80211_band band,
u16 channel)
{
return 0;
}
-EXPORT_SYMBOL(iwlcore_set_rxon_channel);
+EXPORT_SYMBOL(iwl_set_rxon_channel);
static void iwlcore_init_hw(struct iwl_priv *priv)
{
#endif /* CONFIG_IWL4965_HT */
}
+static int iwlcore_init_drv(struct iwl_priv *priv)
+{
+ int ret;
+ int i;
+
+ priv->retry_rate = 1;
+ priv->ibss_beacon = NULL;
+
+ spin_lock_init(&priv->lock);
+ spin_lock_init(&priv->power_data.lock);
+ spin_lock_init(&priv->sta_lock);
+ spin_lock_init(&priv->hcmd_lock);
+ spin_lock_init(&priv->lq_mngr.lock);
+
+ for (i = 0; i < IWL_IBSS_MAC_HASH_SIZE; i++)
+ INIT_LIST_HEAD(&priv->ibss_mac_hash[i]);
+
+ INIT_LIST_HEAD(&priv->free_frames);
+
+ mutex_init(&priv->mutex);
+
+ /* Clear the driver's (not device's) station table */
+ iwlcore_clear_stations_table(priv);
+
+ priv->data_retry_limit = -1;
+ priv->ieee_channels = NULL;
+ priv->ieee_rates = NULL;
+ priv->band = IEEE80211_BAND_2GHZ;
+
+ priv->iw_mode = IEEE80211_IF_TYPE_STA;
+
+ priv->use_ant_b_for_management_frame = 1; /* start with ant B */
+ priv->ps_mode = IWL_MIMO_PS_NONE;
+
+ /* Choose which receivers/antennas to use */
+ iwl_set_rxon_chain(priv);
+
+ iwl_reset_qos(priv);
+
+ priv->qos_data.qos_active = 0;
+ priv->qos_data.qos_cap.val = 0;
+
+ iwl_set_rxon_channel(priv, IEEE80211_BAND_2GHZ, 6);
+
+ priv->rates_mask = IWL_RATES_MASK;
+ /* If power management is turned on, default to AC mode */
+ priv->power_mode = IWL_POWER_AC;
+ priv->user_txpower_limit = IWL_DEFAULT_TX_POWER;
+
+ ret = iwl_init_channel_map(priv);
+ if (ret) {
+ IWL_ERROR("initializing regulatory failed: %d\n", ret);
+ goto err;
+ }
+
+ ret = iwlcore_init_geos(priv);
+ if (ret) {
+ IWL_ERROR("initializing geos failed: %d\n", ret);
+ goto err_free_channel_map;
+ }
+
+ ret = ieee80211_register_hw(priv->hw);
+ if (ret) {
+ IWL_ERROR("Failed to register network device (error %d)\n",
+ ret);
+ goto err_free_geos;
+ }
+
+ priv->hw->conf.beacon_int = 100;
+ priv->mac80211_registered = 1;
+
+ return 0;
+
+err_free_geos:
+ iwlcore_free_geos(priv);
+err_free_channel_map:
+ iwl_free_channel_map(priv);
+err:
+ return ret;
+}
+
int iwl_setup(struct iwl_priv *priv)
{
int ret = 0;
iwlcore_init_hw(priv);
- ret = priv->cfg->ops->lib->init_drv(priv);
+ ret = iwlcore_init_drv(priv);
return ret;
}
EXPORT_SYMBOL(iwl_setup);
if (ret)
IWL_ERROR("Unable to initialize RFKILL system. "
"Ignoring error: %d\n", ret);
+ iwl_power_initialize(priv);
break;
case IWLCORE_START_EVT:
+ iwl_power_update_mode(priv, 1);
break;
case IWLCORE_STOP_EVT:
break;
}
EXPORT_SYMBOL(iwl_send_statistics_request);
+/**
+ * iwl_verify_inst_sparse - verify runtime uCode image in card vs. host,
+ * using sample data 100 bytes apart. If these sample points are good,
+ * it's a pretty good bet that everything between them is good, too.
+ */
+static int iwlcore_verify_inst_sparse(struct iwl_priv *priv, __le32 *image, u32 len)
+{
+ u32 val;
+ int ret = 0;
+ u32 errcnt = 0;
+ u32 i;
+
+ IWL_DEBUG_INFO("ucode inst image size is %u\n", len);
+
+ ret = iwl_grab_nic_access(priv);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < len; i += 100, image += 100/sizeof(u32)) {
+ /* read data comes through single port, auto-incr addr */
+ /* NOTE: Use the debugless read so we don't flood kernel log
+ * if IWL_DL_IO is set */
+ iwl_write_direct32(priv, HBUS_TARG_MEM_RADDR,
+ i + RTC_INST_LOWER_BOUND);
+ val = _iwl_read_direct32(priv, HBUS_TARG_MEM_RDAT);
+ if (val != le32_to_cpu(*image)) {
+ ret = -EIO;
+ errcnt++;
+ if (errcnt >= 3)
+ break;
+ }
+ }
+
+ iwl_release_nic_access(priv);
+
+ return ret;
+}
+
+/**
+ * iwlcore_verify_inst_full - verify runtime uCode image in card vs. host,
+ * looking at all data.
+ */
+static int iwl_verify_inst_full(struct iwl_priv *priv, __le32 *image,
+ u32 len)
+{
+ u32 val;
+ u32 save_len = len;
+ int ret = 0;
+ u32 errcnt;
+
+ IWL_DEBUG_INFO("ucode inst image size is %u\n", len);
+
+ ret = iwl_grab_nic_access(priv);
+ if (ret)
+ return ret;
+
+ iwl_write_direct32(priv, HBUS_TARG_MEM_RADDR, RTC_INST_LOWER_BOUND);
+
+ errcnt = 0;
+ for (; len > 0; len -= sizeof(u32), image++) {
+ /* read data comes through single port, auto-incr addr */
+ /* NOTE: Use the debugless read so we don't flood kernel log
+ * if IWL_DL_IO is set */
+ val = _iwl_read_direct32(priv, HBUS_TARG_MEM_RDAT);
+ if (val != le32_to_cpu(*image)) {
+ IWL_ERROR("uCode INST section is invalid at "
+ "offset 0x%x, is 0x%x, s/b 0x%x\n",
+ save_len - len, val, le32_to_cpu(*image));
+ ret = -EIO;
+ errcnt++;
+ if (errcnt >= 20)
+ break;
+ }
+ }
+
+ iwl_release_nic_access(priv);
+
+ if (!errcnt)
+ IWL_DEBUG_INFO
+ ("ucode image in INSTRUCTION memory is good\n");
+
+ return ret;
+}
+
+/**
+ * iwl_verify_ucode - determine which instruction image is in SRAM,
+ * and verify its contents
+ */
+int iwl_verify_ucode(struct iwl_priv *priv)
+{
+ __le32 *image;
+ u32 len;
+ int ret;
+
+ /* Try bootstrap */
+ image = (__le32 *)priv->ucode_boot.v_addr;
+ len = priv->ucode_boot.len;
+ ret = iwlcore_verify_inst_sparse(priv, image, len);
+ if (!ret) {
+ IWL_DEBUG_INFO("Bootstrap uCode is good in inst SRAM\n");
+ return 0;
+ }
+
+ /* Try initialize */
+ image = (__le32 *)priv->ucode_init.v_addr;
+ len = priv->ucode_init.len;
+ ret = iwlcore_verify_inst_sparse(priv, image, len);
+ if (!ret) {
+ IWL_DEBUG_INFO("Initialize uCode is good in inst SRAM\n");
+ return 0;
+ }
+
+ /* Try runtime/protocol */
+ image = (__le32 *)priv->ucode_code.v_addr;
+ len = priv->ucode_code.len;
+ ret = iwlcore_verify_inst_sparse(priv, image, len);
+ if (!ret) {
+ IWL_DEBUG_INFO("Runtime uCode is good in inst SRAM\n");
+ return 0;
+ }
+
+ IWL_ERROR("NO VALID UCODE IMAGE IN INSTRUCTION SRAM!!\n");
+
+ /* Since nothing seems to match, show first several data entries in
+ * instruction SRAM, so maybe visual inspection will give a clue.
+ * Selection of bootstrap image (vs. other images) is arbitrary. */
+ image = (__le32 *)priv->ucode_boot.v_addr;
+ len = priv->ucode_boot.len;
+ ret = iwl_verify_inst_full(priv, image, len);
+
+ return ret;
+}
+EXPORT_SYMBOL(iwl_verify_ucode);
+