-@c Copyright (C) 1991-2015 Free Software Foundation, Inc.
+@c Copyright (C) 1991-2017 Free Software Foundation, Inc.
@c This is part of the GAS manual.
@c For copying conditions, see the file as.texinfo.
@ifset GENERIC
@item -mips16
@itemx -no-mips16
Generate code for the MIPS 16 processor. This is equivalent to putting
-@code{.set mips16} at the start of the assembly file. @samp{-no-mips16}
+@code{.module mips16} at the start of the assembly file. @samp{-no-mips16}
turns off this option.
@item -mmicromips
@itemx -mno-micromips
Generate code for the microMIPS processor. This is equivalent to putting
-@code{.set micromips} at the start of the assembly file. @samp{-mno-micromips}
-turns off this option. This is equivalent to putting @code{.set nomicromips}
-at the start of the assembly file.
+@code{.module micromips} at the start of the assembly file.
+@samp{-mno-micromips} turns off this option. This is equivalent to putting
+@code{.module nomicromips} at the start of the assembly file.
@item -msmartmips
@itemx -mno-smartmips
Enables the SmartMIPS extensions to the MIPS32 instruction set, which
provides a number of new instructions which target smartcard and
cryptographic applications. This is equivalent to putting
-@code{.set smartmips} at the start of the assembly file.
+@code{.module smartmips} at the start of the assembly file.
@samp{-mno-smartmips} turns off this option.
@item -mips3d
@item -mdspr2
@itemx -mno-dspr2
Generate code for the DSP Release 2 Application Specific Extension.
-This option implies -mdsp.
+This option implies @samp{-mdsp}.
This tells the assembler to accept DSP Release 2 instructions.
@samp{-mno-dspr2} turns off this option.
+@item -mdspr3
+@itemx -mno-dspr3
+Generate code for the DSP Release 3 Application Specific Extension.
+This option implies @samp{-mdsp} and @samp{-mdspr2}.
+This tells the assembler to accept DSP Release 3 instructions.
+@samp{-mno-dspr3} turns off this option.
+
@item -mmt
@itemx -mno-mt
Generate code for the MT Application Specific Extension.
1004kf2_1,
1004kf,
1004kf1_1,
+interaptiv,
+m5100,
+m5101,
p5600,
5kc,
5kf,
sb1,
sb1a,
i6400,
+p6600,
loongson2e,
loongson2f,
loongson3a,
By default @samp{--no-relax-branch} is selected, causing any out-of-range
branches to produce an error.
+@item -mignore-branch-isa
+@itemx -mno-ignore-branch-isa
+Ignore branch checks for invalid transitions between ISA modes.
+
+The semantics of branches does not provide for an ISA mode switch, so in
+most cases the ISA mode a branch has been encoded for has to be the same
+as the ISA mode of the branch's target label. If the ISA modes do not
+match, then such a branch, if taken, will cause the ISA mode to remain
+unchanged and instructions that follow will be executed in the wrong ISA
+mode causing the program to misbehave or crash.
+
+In the case of the @code{BAL} instruction it may be possible to relax
+it to an equivalent @code{JALX} instruction so that the ISA mode is
+switched at the run time as required. For other branches no relaxation
+is possible and therefore GAS has checks implemented that verify in
+branch assembly that the two ISA modes match, and report an error
+otherwise so that the problem with code can be diagnosed at the assembly
+time rather than at the run time.
+
+However some assembly code, including generated code produced by some
+versions of GCC, may incorrectly include branches to data labels, which
+appear to require a mode switch but are either dead or immediately
+followed by valid instructions encoded for the same ISA the branch has
+been encoded for. While not strictly correct at the source level such
+code will execute as intended, so to help with these cases
+@samp{-mignore-branch-isa} is supported which disables ISA mode checks
+for branches.
+
+By default @samp{-mno-ignore-branch-isa} is selected, causing any invalid
+branch requiring a transition between ISA modes to produce an error.
+
@cindex @option{-mnan=} command line option, MIPS
@item -mnan=@var{encoding}
This option indicates whether the source code uses the IEEE 2008
@code{.set nodspr2} directive prevents DSP Release 2 instructions from
being accepted.
+@cindex MIPS DSP Release 3 instruction generation override
+@kindex @code{.set dspr3}
+@kindex @code{.set nodspr3}
+The directive @code{.set dspr3} makes the assembler accept instructions
+from the DSP Release 3 Application Specific Extension from that point
+on in the assembly. This directive implies @code{.set dsp} and
+@code{.set dspr2}. The @code{.set nodspr3} directive prevents DSP
+Release 3 instructions from being accepted.
+
@cindex MIPS MT instruction generation override
@kindex @code{.set mt}
@kindex @code{.set nomt}
projects / deliverable / binutils-gdb.git / blobdiff